Electrolux EK26010LSW User manual

EK 260 10 RE WE

EK 260 10 LI WE

EK 320 10 RE WE

EK 320 10 LI WE

7083 417-01

GEBRAUCHSANWEISUNG

MODE D'EMPLOI

ISTRUZIONE D'USO

OPERATING INSTRUCTIONS

D

GB

F

I

Seite 2

Page 10

Pagina 18

Page 26

Einbaukühlschrank Réfrigérateur encastrable Frigorifero da incasso Built-in refrigerator

Page is loading ...

26

Description of the appliance

Type plate

Adjustable shelves

Adjustable door rack

Butter and cheese

compartment

Operating and control

elements

Vegetable bins

Interior light

(LED light strip)

Disposal notes

The appliance contains reusable materials and should

be disposed of properly - not simply with unsorted

household refuse. Appliances which are no longer

needed must be disposed of in a professional and

appropriate way, in accordance with the current local

regulations and laws.

When disposing of the appliance, ensure that the refrigerant circuit

is not damaged to prevent uncontrolled escape of the refrigerant

it contains (data on type plate) and oil.

• Disable the appliance.

• Pull out the mains plug.

• Cut through the connection cable.

WARNING

Danger of suffocation due to packing material and plastic film!

Do not allow children to play with packaging material. Take the

packaging material to an official collection point.

Freezer tray

Freezing chart

Drawers

Safety instructions and warnings

• To prevent injury or damage to the unit, the ap-

pliance should be unpacked and set up by two

people.

• In the event that the appliance is damaged on

delivery, contact the supplier immediately before

connecting to the mains.

• To guarantee safe operation, ensure that the ap-

pliance is set up and connected as described in

these operating instructions.

• Disconnect the appliance from the mains if any

fault occurs. Pull out the plug, switch off or remove

the fuse.

• When disconnecting the appliance, pull on the

plug, not on the cable.

• Any repairs and work on the appliance should

only be carried out by the customer service

department, as unauthor ised work could prove

highly dangerous for the user. The same applies

to changing the mains power cable.

• Do not allow naked flames or ignition sources

to enter the appliance. When transporting and

cleaning the appliance, ensure that the refrigerant

circuit is not damaged. In the event of damage,

make sure that there are no ignition sources nearby

and keep the room well ventilated.

• Do not stand on the plinth, drawers or doors or

use them to support anything else.

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities or lack of experience and

knowledge unless they have been given initial

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

• Avoid prolonged skin contact with cold surfaces or

chilled/frozen food. This could cause pain, numb-

ness and frostbite. In the case of prolonged skin

contact, protective measures should be taken,

e.g. gloves should be worn.

• Do not eat ice cream, particulary ice lollies or ice

cubes, immediately after taking them from the

freezer compartment as there is a risk of "burning"

because of the very cold temperatures.

• Do not consume food which has been stored for

too long, as it could cause food poisoning.

27

GB

Saving energy

- Always ensure good ventilation. Do not cover ventilation open-

ings or grille.

- Do not place appliance in areas of direct sunlight or next to a

stove, heater or similar object.

- The energy consumption depends on the installation conditions,

e.g. the ambient temperature.

- Keep the time the appliance is open to a minimum.

- Store food logically.

- Ensure that all food is well packed and covered for storage. This

will prevent frost from forming.

- First cool warm food to room temperature before storing it.

- Defrost frozen food in the refrigerator.

Freezer compartment

- If there is a thick layer of frost in the appliance: defrost the appli-

ance.

Setting up

• Standard EN 378 specifies that the room in which you install

your appliance must have a volume of 1 m

3

per 8 g of R 600a

refrigerant used in the appliance, so as to avoid the formation

of inflammable gas/air mixtures in the room

where the appliance is located in the event

of a leak in the refrigerant circuit. The quan-

tity of refrigerant used in your appliance is

indicated on the type plate on the inside of

the appliance.

• Only use the appliance when it is installed.

• Do not cover ventilation openings

or grille.

Electrical connection

Only operate the appliance with alternating current (AC).

The permissible voltage and frequency are indicated on the type

plate. The position of the type plate is shown in the section entitled

Description of the appliance.

The socket must be properly earthed and protected by a fuse.

The tripping current of the fuse must be between 10 A and 16 A.

The socket must not be situated behind the appli-

ance and must be easily accessible.

Do not connect the appliance using an exten-

sion cable or extension socket.

Do not use stand-alone inverters (conversion

of direct current to alternating/three-phase cur-

rent) or energy-saving plugs. Risk of damage

to the electronic control system!

Range of appliance use

The appliance is suitable solely for cooling food in

a domestic environment or similar. This includes,

for example, use

- in staff kitchenettes, bed and breakfast establish-

ments,

- by guests in cottages, hotels, motels and other

forms of accommodation,

- in catering and similar services in the wholesale

trade.

Use the appliance solely as is customary within a domestic envi-

ronment. All other types of use are inadmissible. The appliance

is not suitable for storing and cooling medicines, blood plasma,

laboratory preparations or similar substances and products cov-

ered by the 2007/47/EC Medical Devices Directive. Any misuse

of the appliance may result in damage to or spoilage of stored

goods. Furthermore, the appliance is not suitable for operation in

potentially explosive atmospheres.

Climate rating

The climate rating indicates the room tem-

perature at which the appliance may be

operated in order to achieve full refrigeration

performance.

The climate rating is indicated on the type

plate.

The position of the type plate is shown in the section entitled

Description of the appliance.

Climate rating Room temperature

SN +10°C to +32°C

N +16°C to +32°C

ST +16°C to +38°C

T +16°C to +43°C

SN-ST +10°C to +38°C

SN-T +10°C to +43°C

Do not operate the appliance outside the speci-

fied room temperature range.

• Do not store explosives or sprays using combusti-

ble propellants such as butane, propane, pentane,

etc. in the appliance. Electrical components might

cause leaking gas to ignite. You may identify such

sprays by the printed contents or a flame symbol.

• Do not use electrical appliances inside the appli-

ance.

• The LED light strip illuminates the interior of the

appliance. It is not suitable for lighting a room.

28

Additional functions

In set-up mode you can set the

child lock and adjust the bright-

ness of the display.

Activating set-up mode:

• Press the

button 4 for approx. 5 seconds.

- The

button flashes.

- The display shows c for child lock.

Note: The value to be altered flashes.

• Select the required function by pressing the

/ button 2:

c = child lock,

h = display brightness or

• Now select/acknowledge the function by pressing the

button

briefly:

> For c = child-proof lock,

press the

/ button 2 to select

c1 = child lock on or

c0 = child lock off and acknowledge with the

but-

ton

4. When the symbol is lit, the child lock is

activated.

> For h = brightness,

press the

/ button 2 to select

h1 = minimum to

h5 = maximum brightness and acknowledge with the

button 4.

Exiting set-up mode:

• Exit the set-up mode by pressing the On/Off button

3; after

2 min. the electronic system switches over automatically. The

normal operating mode is activated again.

Power failure „frost-control“ display

If nA appears in the display, this means that the freezer tempera-

ture has risen too high during the last few hours or days due to a

power failure.

If you press the „ALARM“ button whilst the display is

reading nA, the highest temperature registered during

the power failure will be displayed. Check the quality

of the food and its suitability for consumption in case

it has become too warm or even defrosted.

The highest temperature will appear for appox. 1 minute. After that,

the actual temperature in the freezer will re-appear. The display

can be switched off by repeatedly pressing the „ALARM“ button.

Audible warning signal

The appliance is equipped with an alarm function.

Audible/visual temperature alarm:

It sounds when it is not cold enough in the freezer compartment.

The temperature display will also flash;

The audible warning device is switched off by pressing the button.

The temperature display will continue to flash until the cause of

the alarm has been rectified.

This can be caused by:

• the freezer door being left open for a long time, allowing warm

ambient air to enter;

• a long power failure;

• a fault in the appliance.

In each case, make sure food has not defrosted or perished.

Operating and control elements

Setting the temperature

2

To reduce the temperature

Press the

button (on left for refrigerator, on right for freezer).

To increase the temperature/warmer

Press the

button each.

- When pressing one of the buttons for the first time, the display

will start to flash.

- Pressing this button again enables you to change the temperature

setting.

- The electronic controls will switch over automatically about

5 seconds after the last time you pressed the button, and the

actual temperature will be displayed.

- You can change the temperatures

in the refrigerator between 9°C and 2°C

in the freezer between -16°C and -26°C.

Frezzer compartment

1Temperature display

2Temperature setting buttons

3On/O button

4Superfrost-button

5Audible warning On/O button

6Child lock is activated

Refrigerator compartment

7Temperature display

8Temperature setting buttons

9On/O button

bl button (The button

switches the refrigerator

compartment to maximum

cooling)

Switching the appliance on and off

3

You are recommended to clean the appliance before switching it

on for the first time (see „Cleaning“).

Switching on: Press the ON / Off buttons (on left for refrigerator, on

right for freezer) so that the temperature display lights up/flashes.

Switching off: Press the On / Off buttons for approx. two seconds

so that the temperature display goes out.

Note

If the freezer compartment is switched off, the appliance is out

of operation.

Temperature display

In normal operation, the average refrigerator temperature 7and

the warmest frozen food temperature

1will be displayed.

When starting up for the first time or when the appliance is warm,

dashes will appear until the temperature reaches a level that can

be displayed (19° to 0°C in the refrigerator and below 0°C in the

freezer).

If F1 to F5 appears in the display, the appliance has a fault. Con-

sult the customer serv ice department indicating the fault number

displayed.

29

Cooling

Storage example

➊ butter, cheese

➋ eggs

➌ bottles

➍ frozen food, ice cubes

➎ baked goods, pre-cooked meals,

drinks

➏ meat, sausage products, dairy

products

➐ salad, fruit, vegetables, fresh

herbs

Note

• Food which gives off or absorbs

odours and flavours as well as

liquids should always be stored

covered or in closed contain-

ers. High- percentage alcohols

should be tightly sealed and

stored upright.

• Fruit, vegetables, salad can be

stored unpacked in the bins.

GB

Button

The button switches the refrigerator compartment to maximum

cooling. This is recommended particularly if you wish to cool large

quantities of fresh food or drinks as fast as possible.

Switching on

Press the

button briefly so

that the LED comes on. The re-

frigerator temperature will drop

to its lowest value.

After approx. 6 hours, however, the refrigerator switches back

automatically to normal operation.

Cooling with fan

With the fan function switched on, a uniform temperature distribu-

tion will be attained in the refrigerator compartment.

This is recommended:

- in high room temperatures

(approx. 33°C or higher),

- if the air humidity is high (e.g.

during the summer).

To switch on

= on

To switch off

= off

Interior LED light

The interior light switches off auto-

matically after the door has been

opened for approx. 15 minutes.

If the interior light does not switch

on when the door is opened briefly,

but the temperature display is

wo rki n g, t he li g ht m ay b e d efect i ve.

The light intensity of the LED

light corresponds to laser class

1/1M.

Important

The light cover may only be removed by customer service

staff. If the cover is removed, do not look directly at the

light through optical lenses from close distance. This can

damage your eyes.

Repositioning the door racks

- Lift door rack vertically, lift out to

the front and re-insert at a different

height, following these steps in the

reverse order.

Equipment

You can re-arrange the storage

shelves as required.

Lift the glass shelf, align the recess

over the support and replace the shelf

in a higher or lower position.

The sectioned glass shelves

can be moved to make space for

tall containers. Place the shelf

rails provided, fig. 1, on the sup-

ports on the left and right at the

desired height.

Insert the glass shelves

1 and

2 as shown in fig. 2. The glass

shelf

2 with the raised edge

must go at the back.

If you need to make space for

tall containers, simply slide

the front half of the sectioned

glass shelf carefully under-

neath the back half, fig. 2.

g. 1 g. 2

30

Freezing chart

The freezing chart represents the frozen

food and the time it can be safely stored

in months.

The individual storage times and

whether or not the lower or upper

value is applicable depend on the food

quality, its processing prior to freezing,

and the individual household‘s quality

requirements.

The lower values always apply to food

with a high fat content.

Freezer tray

You can use the freezer tray to gently freeze fruit (e.g. berries or

slices of fruit), herbs and vegetables

for serving or garnishing.

Spread the food out loosely on the tray

(the pieces of fruit will retain their shape

and will not stick together). Freeze for

10 to 12 hours then transfer to a freezer

bag or container and store in one of

the drawers.

Notes on freezing

• Pack food which you are freezing yourself in quantities appropriate

to your household. To ensure that the food freezes right through,

the following quantities should not be exceeded per package:

fruit, vegetables: up to 1 kg, meat: up to 2.5 kg.

• Pack frozen food in standard freezer bags or reuseable plastic,

metal or aluminium containers.

• Do not allow fresh food which is to be frozen to come into contact

with food already frozen. Always keep packs dry in order to avoid

them sticking together.

• A l way s w rit e t he da te a n d c onte n ts on the p ac k a nd do not exce e d

the stated storage time for the food.

• Do not freeze bottles and cans which contain carbonated drinks

as they might burst.

• Only take out as much food as is immediately required for thawing.

Use food which has been thawed in prepared meals as quickly

as possible.

Frozen food can be thawed in the following ways:

– in a fan oven

– in a microwave oven

– at room temperature

– in the refrigerator

Making ice cubes

• Fill the ice-cube tray with water.

• Place the ice-cube tray in the appliance

and leave it to freeze.

• The ice cubes can be removed from the

tray by twisting or by holding upside down

for a short time under running water.

Freezing with Superfrost

By activating the Superfrost function the temperature in the freezer

compartment will drop to the lowest attainable value. Thus food

can be rapidly frozen to the core and the quality is preserved.

• Press the Superfrost button

4.

• Wait 24 hours.

• Place the fresh food in the

freezer.

• The Superfrost facility auto-

matically switches the fast

freezing procedure off after 65 hours.

You should not switch on the Superfrost function:

- when placing frozen food in the freezer;

- when freezing up to approx. 2 kg fresh food daily.

Freezing

Fresh food should be frozen to the

core as rapidly as possible. Frozen

food can also be given a cold boost.

This is provided by the „Superfrost“

facility.

The maximum amount of food wich

can be frozen in 24 hours is shown

on the type plate („Freezing capac-

ity...kg/24 hours").

31

GB

Shutting your appliance down

If your appliance is to be shut down for any length of time, switch

it off and disconnect the plug or switch off or unscrew the fuse.

Clean the appliance and leave the door open in order to prevent

unpleasant smells.

The appliance complies with the relevant safety regulations and

EC Directives 2004/108/EC and 2006/95/EC.

All types and models are subject to continuous improvement and

the manufacturer therefore reserves the right to make modifica-

tions to the shape, equipment and technology.

Malfunctions

You may be able to rectify the following faults by checking

the possible causes yourself:

• Appliance does not function:

– Is the appliance switched on?

– Is the plug correctly fitted in the mains socket?

– Is the socket fuse intact?

• Loud running noise:

– Is the appliance set up firmly on the floor?

– Does the appliance cause nearby items of furniture or objects to

vibrate? Please note that noises caused by the refrigerant circuit

cannot be avoided.

• The temperature is not low enough:

– Is the temperature setting correct (see "Setting the temperature")?

– Have excessive amounts of fresh food been placed in the appli-

ance?

– Does the separately installed thermometer show the correct

reading?

– Is the ventilation system working properly?

– Is the appliance set up too close to a heat source?

• The inside of the appliance may feel warm in places

– That is quite normal. The dissipated heat is necessary for normal

operation of the appliance.

If none of the above causes apply

and you cannot rectify the fault

yourself, contact the nearest

customer service department

stating the type of appliance ➊,

PNC number ➋ and appliance

number ➌ as indicated on the

type plate.

The position of the type plate

is shown in the section entitled

Description of the appliance.

Cleaning

Before cleaning always switch o the appliance. Disconnect

from the mains or unscrew or switch o the fuse.

• Clean the inside, equipment parts and outer walls with lukewarm

water and a little detergent. Do not use abrasive or acid cleaners

or chemical solvents.

• Ensure that no cleaning water penetrates into the electrical

components or ventilation grille.

• Dry all parts well with a cloth.

• Do not damage or remove the type plate on the inside of the

appliance. It is very important for servicing purposes.

• Clean the drain hole in the refrigerator compartment with a thin

object, e.g. cotton swab or the like.

Do not use steam cleaners because of the risk

of injury and damage.

Defrosting

Refrigerator compartment

The refrigerator compartment de-

frosts automatically. The condensate

evaporates automatically through the

compressor heat.

Ensure that the water can flow without

hindrance through the hole above the

vegetable bins.

Freezer compartment

After the appliance has been in operation for some time, a layer

of frost or ice will form on the inside walls. This increases energy

consumption. Therefore defrost the freezer compartment regularly.

• Switch the appliance off to

defrost. Pull out the mains plug

or press the freezer compart-

ment- On / Off button

3 so

that the temperature display

goes dark.

• Remove the drawers and glass shelves.

• Wrap the frozen food in paper or blankets and store in a cool

place.

• To speed up the defrosting process put a saucepan of hot water

on the compartment floor.

• Leave the door of the appliance open while defrosting. After

defrosting mop up the remaining water and clean the appliance.

Do not use any mechanical devices or other

artificial aids for defrosting other than those

recommended by the manufactur er.

32

Changing over door hinges

• Unscrew decor frame 1.

• Tilt the door to the front and lift off.

• Transfer plug

bm.

• Remove cover

bl.

• Unscrew hinge bracket

5.

• Transfer cover

9 to the opposite side.

• Unscrew hinge bracket

6 and lift lower door o upwards.

• Transfer plug

bn.

• Unscrew hinge pin

3and screw into the adjacent fastening hole.

• Unscrew hinge bracket

8.

• Unscrew hinge pin

7 and screw into the adjacent fastening hole.

• Remove covers

2 and transfer to the opposite side.

• Remove plugs

4 and transfer to the opposite side.

• Screw hinge bracket

8 into place on the opposite side.

• Suspend lower door on hinge pin

8 and close.

• Screw hinge bracket

6 into place on the opposite side.

• Screw hinge bracket

5 into place on the opposite side.

• Replace cover

bl.

• Suspend upper door on hinge pin

6 and close.

• Insert hinge pin

1 and tighten.

Installation dimensions (mm)

A B C

SMS 12/6 1524 1523 1514

SMS 14/6 1778 1777 1768

33

GB

Assembling decor panels

Decor panel dimensions EK 260

Height Width Thickness max.

Refrigerator 845 mm 535 mm 4 mm

Freezer 598 mm 535 mm 4 mm

Decor panel dimensions EK 320

Height Width Thickness max.

Refrigerator 1099 mm 535 mm 4 mm

Freezer 598 mm 535 mm 4 mm

Assembly

• Unscrew door handle.

• Unscrew decor frames

1.

• Loosen decor frames

2

and slide forwards.

• Slide the decor panel

3between the frames

and the door.

• Screw on the decor frames

1with handle.

• Slide all decor frames

back and screw tightly.

Installing in a kitchen unit

• Slide the attachment element

into the rail underneath the

appliance on the handle side

on the left or right, depending

on which side the handle is.

Screw into place with screw

3.5 x 17.

• Slide the appliance into the

recess.

Fastening in the recess

Fasten the appliance in the recess

- with the attachment profile at the top A1,

- with the attachment element at the bottom A2.

Page is loading ...

Electrolux EK26010LSW User manual

This manual is also suitable for

Electrolux EK26010LSW User manual

in other languages

Related papers

Other documents