Tascam DA-6400 User manual

Type
User manual

This manual is also suitable for

TASCAM DA-6400/DA-6400dp
1
DA-6400/DA-6400dp
D01283920F
Contents
New functions in firmware version 2.10 ................................................................................................................................................... 2
Cascade function support .................................................................................................................................................................................................................... 2
cascade status added to INFORMATION screen ........................................................................................................................................................................... 7
New functions in firmware version 2.00 ................................................................................................................................................... 8
Playlist function supported .................................................................................................................................................................................................................. 8
Theater play function added .............................................................................................................................................................................................................17
AUTO READY function added ............................................................................................................................................................................................................18
Support for timecode synchronized playback of all takes in the current folder ............................................................................................................19
Support for playback of WAV files in 32-bit PCM and 32-bit floating formats ................................................................................................................. 19
Take list sorting functions added .....................................................................................................................................................................................................19
Home Screen menu functions added ............................................................................................................................................................................................20
My MENU function added ..................................................................................................................................................................................................................21
mDNS (Multicast DNS) supported for easy network connection .........................................................................................................................................22
Two types of VNC server compressed transmission formats supported ........................................................................................................................... 23
“None” added to REC FILE FORMAT menu FILE NAME setting ..............................................................................................................................................23
SNTP menu page now shows current date and time ...............................................................................................................................................................23
Current folder name added to INFORMATION screen .............................................................................................................................................................. 23
Marks added automatically at buffer overflows during recording ...................................................................................................................................... 23
Change in display when Master Clock is not locked. ................................................................................................................................................................ 23
Track Names and other metadata added to BEXT chunk data of BWF files .....................................................................................................................23
iXML chunk data of Track Names and other metadata added to BWF files ......................................................................................................................23
New functions in firmware version 1.50 ................................................................................................................................................. 24
TRACK NAMES function added ......................................................................................................................................................................................................... 24
New functions in firmware version 1.40 ................................................................................................................................................. 26
TASCAM IF-AN16/OUT analog output interface card support added ................................................................................................................................ 26
New functions in firmware version 1.30 ................................................................................................................................................. 28
TASCAM DA-6400 Control iPad remote control app support added .................................................................................................................................. 28
TASCAM IF-AE16 AES/EBU interface card support added .......................................................................................................................................................28
Function added to synchronize with SMPTE timecode and play the current take ........................................................................................................29
VAMPING mode added to repeat playback function modes .................................................................................................................................................30
Function added to set the input and output signal routing for each individual channel...........................................................................................31
On/off setting added for NO SIGNAL error checking function .............................................................................................................................................33
Function added that requires pressing and holding the button to stop recording ......................................................................................................33
New functions in firmware version 1.21 ................................................................................................................................................. 34
Support for the TASCAM IF-DA64 Dante interface card ..........................................................................................................................................................34
Owner's Manual Addendum .................................................................................................................................................................... 35
FTP connection settings note ...........................................................................................................................................................................................................35
Function explanation additions and changes .............................................................................................................................................................................35
Document corrections ......................................................................................................................................................................................................................... 36
0418.MA-2475B
DA-6400/DA-6400dp
2
TASCAM DA-6400/DA-6400dp
New functions in firmware version 2.10
The following new functions have been added in firmware version 2.10.
0 A cascade function that allows simultaneous recording/playback operations on two units is now supported.
0 The
INFORMATION
screen now shows the cascade status.
Cascade function support
A cascade function is now supported. This allows simultaneous recording/playback operations with sample-precise synchronization on
two units that are connected to the same network. Cascade operation of up to two units is possible with the following simultaneous re-
cording/playback channel limits.
0 When the sampling frequency is 44.1/48 kHz, up to 64 channels on 2 units (128 total channels)
0 When the sampling frequency is 88.2/96 kHz, up to 32 channels on 2 units (64 total channels)
Cascade function setup
Use the
CASCADE
page added to the menu screen to make cascade function settings and check its status.
CASCADE STATUS
This shows the cascade status.
Cascade status ERROR/ALERT classification Contents
Cascade OFF
--- The cascade function is off.
Offline
(No Network)
ERROR
Cascade operation is not possible because it is not connected to a
network.
Offline
(Duplicate Slave)
ERROR
Proper cascade operation is not possible because multiple units are
set to the same cascade slave ID.
Offline
(Duplicate Master)
ERROR
Cascade operation is not possible because multiple units are set as
the cascade master.
Comms Lost with
Slave
ALERT
The cascade master is no longer able to communicate to one of the
cascade slaves.
Offline (No
Slaves)
ALERT
Cascade operation is not possible because no unit set to be a cas-
cades slave could be found on the network.
Offline (No Mas-
ter)
ERROR
Cascade operation is not possible because no unit set to be the cas-
cade master could be found on the network.
Syncing... ERROR
Cascade synchronization is being prepared.
Waiting... ERROR
The unit is waiting for cascade to be ready.
OK (N active)
--- Cascade synchronization is working properly for N number of units.
TASCAM DA-6400/DA-6400dp
3
DA-6400/DA-6400dp
NOTE
i The cascade status is also shown on the
INFORMATION
screen.
i If the status is anything other than
Cascade OFF
or
OK
, the INFO indicator lights red, and an
ERROR INFORMATION
or
ALERT
INFORMATION
screen appears with an error/alert as shown below.
ERROR INFORMATION
screen
ALERT INFORMATION
screen
i If one of the above cascade errors occurs, recording/playback cannot be started.
i If one of the above cascade alerts occurs, recording/playback can be started. if the error is
Offline (No Slaves)
, then only the
cascade master unit will operate.
CASCADE UNITS
This shows the IDs of the cascade units recognized by this unit.
Check whether each device is operating with cascade synchronization by looking at its
CASCADE STATUS
item.
Example when MASTER and SLAVE-1 devices are recognized:
M S1
Example when no devices are recognized:
NONE
CASCADE SETUP
Use this to set up the cascade function.
Select
CASCADE SETUP
, and press the MULTI JOG dial to open a screen where you can change the cascade function settings.
When on
APPLY
in the last line, press the MULTI JOG dial to confirm the changed settings and return to the Menu Screen.
Press the EXIT [PEAK CLEAR] button to cancel the menu operation and return to the Menu Screen.
CASCADE MODE
This sets the cascade operation mode.
Options
OFF
(default): This disables the cascade function.
ON
: This enables the cascade function.
CASCADE ID
This sets the cascade device ID.
The cascade ID should always be set to one not used by any other device.
Option Meaning
MASTER
(default) Sets this unit as the cascade master.
SLAVE-01
Sets this unit as cascade slave 1.
DA-6400/DA-6400dp
4
TASCAM DA-6400/DA-6400dp
Home Screen in cascade mode
When
CASCADE MODE
is on, the top right of the Home Screen will appear as follows.
This will blink if the
CASCADE STATUS
is not
OK
.
Cascade status Cascade master unit Cascade slave 1
Off
No cascade indicator
Normal
Appears with blue background Appears with yellow background
Connecting
Blinks with blue background Blinks with yellow background
2
x
2
x
Error occurring
Blinks with red background
2
x
2
x
Recording file name format in cascade mode
When
CASCADE MODE
is
ON
, recorded files will be named with the following format.
Tnnn_<name>_<ID>_TTT_tt.wav
nnn: Take number
<name>: Name according to
REC FILE FORMAT
screen
FILE NAME
setting.
<ID>: Characters that show cascade ID (M/S1)
TTT: Number
tt: Channel number
TASCAM DA-6400/DA-6400dp
5
DA-6400/DA-6400dp
Examples:
Recording file names for cascade master unit
Recording file names for cascade slave unit
T001_TASCAM_M_001_01.wav
T001_TASCAM_M_001_02.wav
:
T001_TASCAM_M_001_63.wav
T001_TASCAM_M_001_64.wav
T001_TASCAM_S1_001_01.wav
T001_TASCAM_S1_001_02.wav
:
T001_TASCAM_S1_001_63.wav
T001_TASCAM_S1_001_64.wav
Attention
If a take that has the name specified by the cascade master device already exists on the cascade slave device when recording starts, an
"A" will be added to the characters that show the cascade ID in the name of the take recorded (e.g. T001_TASCAM_S1A_001).
Be aware that since takes are selected for cascade playback by take name, the intended take will not be played back if this take is se-
lected.
Example when the FILE NAME setting is USER WORD “TASCAM”
Cascade master device Cascade slave device
Before recording No take T001_TASCAM_S1_001
Start of record-
ing
T001_TASCAM_M_001
Since a take named T001_TASCAM_S1_001” already
exists, the name T001_TASCAM_S1A_001” will be used
for recording
After recording T001_TASCAM_M_001
T001_TASCAM_S1_001
T001_TASCAM_S1A_001
Playback Cascade playback will play T001_TASCAM_M_001 and T001_TASCAM_S1_001
Current Folder during Cascade operation
0 Cascade slave's current folder will be the same name as the current folder on the Cascade Master. If a folder with the same name does
not exist on the slave, it will be created automatically.
0 If a new folder is created on the Master, a folder of the same name is also created on the slave.
0 If a folder is loaded on the Master, the slave will automatically load the folder with the same name.
Limitations
0 To operate the Cascaded devices together, use the transport controls* on the Master. If the transport controls on a Cascade slave are
operated, that unit will operate independently.
* Transport operation using the buttons on the front of the unit, RS-422, NETWORK (including TASCAM DA-6400 Control) or PARALLEL
control, or a USB keyboard
0 When the following settings are made on the cascade master, the cascade slave unit will be set the same way.
The following settings cannot be changed on a cascade slave unit during cascade connection.
o
REC FUNCTION
,
ALL ON
and
ALL OFF
settings on the
REC FILE FORMAT
menu page (channel settings can be set for each
unit individually when
Individual
)
o
REC FILE FORMAT
menu page
BIT LENGTH
setting
o
REC FILE FORMAT
menu page
REC Fs
setting
o
REC OPTIONS
menu page
AUTO FILE INCREMENT
,
PAUSE MODE
setting
o
PLAY SETUP
menu page
PLAY MODE
,
REPEAT MODE
,
THEATER PLAY
and
AUTO READY
settings
0 The file name recorded on the cascade slave does not depend on the cascade slave device's
FILE NAME
setting, it uses the file name
provided by the cascade master device.
0 The Timestamp recorded into files on a cascade slave device does not depend on the cascade slave devices Timecode Settings, it is
always received directly from the cascade master device.
0 The cascade slave device always plays back the take that matches the cascade master devices take, regardless of the cascade slave
devices's
PLAY SETUP
menu settings.
0 When cascaded, Folders cannot be deleted or renamed on cascade slave devices. Disable cascade before attempting to delete or re-
name folders.
0 This unit does not have a function that mixes the monitoring output of the cascade units. The channels selected on each unit will be
output from their own PHONES jacks for monitoring.
0 When in Playlist Mode,
CASCADE MODE
cannot be set to
ON
.
0 If
CASCADE MODE
is
ON
when a playlist is loaded and Playlist Mode is activated,
CASCADE MODE
will automatically turn
OFF
.
0 When
CASCADE MODE
is
ON
,
CHASE MODE
cannot be turned
ON
. For details about timecode synchronized playback of multiple units,
see “Support for timecode synchronized playback of all takes in the current folder” on page 19.
DA-6400/DA-6400dp
6
TASCAM DA-6400/DA-6400dp
Procedures to enable cascade operation
Audio clock synchronization is necessary for cascade connections and connecting multiple DA-6400 units.
See step 4 below for details about audio clock synchronization.
1. Set
CASCADE MODE
to
ON
on all units.
2. Set the
CASCADE ID
of one unit to
MASTER
, and set the other unit to
SLAVE-01
.
3. Connect all the units to the same network.
When connecting to a network that has a DHCP server or when only the DA-6400 and a hub are connected in a network that does not
have a DHCP server, set the
IP SETUP
MODE
item to
AUTO
on the
NETWORK
menu page.
When computers or devices other than DA-6400 units are connected on a network that does not have a DHCP server and only the
DA-6400 and a hub are connected, set the
IP SETUP
MODE
item to
STATIC
on the
NETWORK
menu page. Also set the
IP ADDR
of
all devices so that the same segments have different values.
Example of settings when the network does not have a DHCP server
CASCADE ID MODE IP ADDR SUBNET
MASTER
STATIC
192.168.100.100
255.255.255.0
SLAVE-01 192.168.100.101
Connection example
WORD THRU
WORD IN
WORD IN
MASTER unit
SLAVE-01 unit
Gigabit hub Clock generator
Connections for cascade synchronization
When setting and connections are completed for 1–3, implementation of the cascade connection will automatically start.
When all the cascade connections are established,
OK
and the number of cascade connected units will appear in the
CASCADE STA-
TUS
line on the
CASCADE
menu page of every device.
In addition, the cascade setting indicator will appear on the Home Screen.
Furthermore, unless there is an error or other issue, the INFO indicator will light blue.
4. Audio clock synchronization requires routing that is separate from the cascade connections.
For this reason, all the units should be connected so that audio clock can be synchronized.
Connection example: Using an external word clock for master clock
WORD THRU
WORD IN
WORD IN
MASTER unit
SLAVE-01 unit
Clock generatorGigabit hub
Connections for audio clock synchronization
TASCAM DA-6400/DA-6400dp
7
DA-6400/DA-6400dp
5. If you want to conduct recording operations using timecode, the same timecode can also be provided to cascade slave unit by input-
ting a timecode signal into the timecode input connector of the cascade master unit.
NOTE
i If a cascade unit is added to the network during recording or playback,
CASCADE UNITS
will appear for that device's ID. That unit will
not be able to operate with cascade synchronization until the cascade-synchronized recording or playback stops.
i If cascade connection is interrupted due to network connection failure during recording or playback, after the network connection is
restored, cascade connection will not be reestablished until it is stopped. For this reason, stopping recording/playback on the master
unit will not stop slave units that have had the cascade connection interrupted. In this case, stop each unit individually. When they are
stopped, implementation of the cascade connection will automatically start.
Cascade recording
After cascade operation settings and connections have been completed, starting/stopping/pausing recording on the cascade master unit
will simultaneously start/stop/pause recording on the cascade slave unit.
Cascade playback
After cascade operation settings and connections have been completed, starting/stopping/pausing playback on the cascade master unit
will simultaneously start/stop/pause playback on the cascade slave unit.
When searching forward/backward on the cascade master unit, the slave unit will not synchronize until after the master unit is stopped.
Then, it will synchronize to the stopping point.
If takes are skipped during playback, the slave unit will synchronize to the master unit playback after it stops skipping. Then, it will also
resume playing.
If takes are skipped when stopped, the slave unit will immediately stop at the same playback take as the master unit.
Takes used for cascade playback
The cascade Master can play back any Take in the current folder whose Sampling rate matches the
Rec FS
setting.
The cascade Slave will play back a take in the folder with the same name as the Master's currently selected folder that matches the
Master's Take according to one of the following rules:
a) The Take name matches the Master's Take name and the cascade ID in the take name matches the slave's Cascade ID.
b) The take name matches the Master's Take name exactly.
If takes for both a) and b) exist in the Slave's current folder, the take matching rule a) is used.
if a take matching rule a) does not exist in the Slave's current folder, a take matching rule b) will be played.
When using cascade playback, as a rule, play takes back on the same units that were used for cascade recording.
If you want to use a take that has a CASCADE ID added to its take name for cascade playback that differs from the cascade ID setting,
do one of the following.
o Change the CASCADE ID to match the take you want to play.
o Edit the CASCADE ID in take name to match the cascade ID setting.
o Edit the slave's Take name to match the Master's Take name.
Examples:
CASCADE ID: SLAVE-1
Take name: T001_TASCAM_M_001
In this state, cascade playback with T001_TASCAM_M_001” is not possible. Do one of the following to enable cascade playback of the
take.
1) Change the
CASCADE ID
setting to
MASTER
to match the take.
2) Change the take name to T001_TASCAM_S1_001” to match the
CASCADE ID
setting.
cascade status added to INFORMATION screen
The
INFORMATION
screen now shows the cascade status.
DA-6400/DA-6400dp
8
TASCAM DA-6400/DA-6400dp
New functions in firmware version 2.00
The following new functions have been added in firmware version 2.00.
0 A playlist function is now supported. This allows takes to be
assigned in any order and playback areas for each one to be
set, for example.
0 A theater play function has been added. This allows the addi-
tion of marks for the playback starting and ending points of
each take and the playback of the set parts of multiple takes
in order.
0 An AUTO READY function has been added. After a take com-
pletes playback, this puts the unit into playback standby at
the beginning of the next take.
0 Timecode synchronized playback of all takes in the current
folder is now supported.
0 Playback of WAV files in 32-bit PCM and 32-bit floating formats
is now supported.
0 Sorting functions have been added that allow the take list to
be arranged in take timecode and take name orders.
0 When the Home Screen is open, pressing the MENU button
while pressing the SHIFT button now opens a menu with op-
erations for the current take or playlist.
0 A My MENU function has been added that can be used to
show only selected menu pages.
0 mDNS is now supported, and network connection with the
DA-6400 can be achieved easily from Mac OS and Telnet, VNC
and FTP apps that support mDNS.
0 Two types of compressed transmission formats are now sup-
ported with the VNC server function.
0
None
has been added to the
FILE NAME
setting on the
REC FILE FORMAT
menu page.
0 The
SNTP
menu page now shows the current date and time.
0 The
INFORMATION
screen now shows the current folder
name.
0 A mark is now set automatically when a buffer overflow occurs
during recording.
0 Change in display when Master Clock is not locked.
0 Track Names and other metadata will now be added to the
BEXT chunk data of BWF files.
0 The iXML chunk data of Track Names and other metadata will
now be added to BWF files.
Playlist function supported
The playlist function now supported makes it possible to assign takes to a list in the order you want, change playback order, and nonde-
structively set playback ranges for audio files without affecting their data.
Loading and writing of JPPA flash start playlist files is supported.
Operation modes
This unit has two operation modes: Take List Mode and Playlist
Mode.
Playing takes in the file list order of the current folder on the
BROWSE
screen is called Take List Mode”. (This operation of the
unit is the same as used before firmware version 2.00).
In contrast, “Playlist Mode allows you to assign takes to a list in
the order you like. The Playlist Mode allows you to change play-
back order, and nondestructively set playback ranges for audio
files without affecting their data, for example.
In Take List Mode, appears to the left of the take name on the
Home Screen.
In Playlist Mode, appears to the left of the take name on the
Home Screen.
Limitations in Playlist Mode
Playlist Mode has the following limitations.
0 Take names cannot be changed.
0 The start timecode of a take cannot be changed
0
CHASE MODE
cannot be set to
ON
.
0 If
CHASE MODE
is
ON
when a playlist is loaded and Playlist
Mode is activated,
CHASE MODE
will automatically turn
OFF
.
0
CASCADE MODE
cannot be set to
ON
.*
0 If
CASCADE MODE
is
ON
when a playlist is loaded and Playlist
Mode is activated,
CASCADE MODE
will automatically turn
OFF
.*
* Supported from firmware version 2.10. (See “Function ex-
planation additions and changes” on page 35.)
Changing operation modes (loading playlists)
To switch between Take List and Playlist Modes, select and the
load a corresponding file on the
BROWSE
screen, either a take
list file (da6400_takes.bin) or a playlist file (JPPA PPL file with ppl
extension).
The following procedures explain switching from Take List Mode
to Playlist Mode.
TASCAM DA-6400/DA-6400dp
9
DA-6400/DA-6400dp
1. Move to the current folder on the
BROWSE
screen from the
menu screen.
As shown by the red frame below ( ), Take List and Playlist
file names are shown with either
<TakeList>
or
<Play-
list>
in gray characters at the top of the folder list.
As shown by the orange frame below ( ), a yellow icon
is shown next to the currently loaded file.
NOTE
If the current folder does not contain any playlist files, the
unit will automatically generate an empty playlist file named,
da6400PPL.ppl
”.
2. Turn the MULTI JOG dial to select a playlist file.
3. Press the MULTI JOG dial to open the menu.
4. Select
LOAD
and press the MULTI JOG dial to open a load
pop-up confirmation message.
5. Press the MULTI JOG dial to open a pop-up message, and
switch to Playlist Mode if a playlist was loaded.
6. When loading completes, the playlist entry list screen opens.
In the current folder list display, a yellow current playlist
icon appears next to the loaded playlist, as shown in the or-
ange frame below ( ).
Creating new playlists
In addition to the automatically created
da6400PPL.ppl
playlist, you can also create new playlists in the JPPA PPL format
in the current folder.
1. Move from the menu screen to the current folder on the
BROWSE
screen, and turn the MULTI JOG dial to select the
current folder or playlist file on the top line.
2. Press the MULTI JOG dial to open the menu, and select
CREATE PLAYLIST
.
3. Press the MULTI JOG dial to open a screen where you can
input the name of the created playlist.
4. Input the name of the playlist being created. For details
about how to input names, see “Editing text in “4 – Record-
ing” of the Owners Manual.
5. After editing the playlist name, select
ENTER
, and press the
MULTI JOG dial to open a confirmation pop-up message.
6. Press the MULTI JOG dial to open a pop-up message, and
create a playlist.
NOTE
i The playlist just created becomes the current playlist.
i If the playlist was created in Take List Mode, the unit switches
to Playlist Mode.
DA-6400/DA-6400dp
10
TASCAM DA-6400/DA-6400dp
Deleting, copying and editing the names of play-
list files
For details about how to delete, copy and edit the names of play-
list files, see “Editing folder, take and file names”, “Deleting folders,
takes and files” and “Copying folders, takes and file in “5 – Work-
ing with Folders (BROWSE screen)” of the Owners Manual.
NOTE
The playlist file that is currently loaded can be copied, but it
cannot be deleted and its name cannot be edited.
Naming and saving playlist files
You can select
SAVE AS
in a menu to give the current playlist file
a name and save it.
1. Open the menu in one of the following ways.
1.1 Move from the menu screen to the
BROWSE
screen cur-
rent folder, and turn the MULTI JOG dial to the loaded
(current) playlist file. Press the MULTI JOG dial to open
the menu.
1.2 On the playlist entry list screen, select playlist in the top
line, and press the MULTI JOG dial to open the menu.
1.3 On the Home Screen, while pressing the SHIFT button,
press the MENU button to open the menu.
2. Select
SAVE AS
, and press the
MULTI JOG
dial to open a
screen where you can input the name of the saved playlist.
3. Input the name of the playlist being saved.
For details about how to input names, see “Editing text in
“4 – Recording of the Owners Manual.
4. After you finish editing the playlist name, select
ENTER
and
press the MULTI JOG dial to start saving it.
A progress pop-up window appears while saving.
This window closes when saving completes.
Playlist editing
Playback units in the playlist are called entries.
A maximum of 999 entries can be assigned to a playlist.
Only takes in the folder that contains the created playlist can be
assigned as entries.
When takes in other folders are assigned to a playlist, they will be
copied to the folder that contains the created playlist.
Playlists can be edited on the playlist entry list screen of the
BROWSE
screen.
NOTE
When editing the contents of a playlist, the playlist file is auto-
matically saved for you at the following timings:
o When going from the playlist entry list screen to any other
screen.
o When going from the playlist entry
ADJUST
screen to any
other screen.
o When the Shutdown popup is confirmed with the MULTI
JOG dial after press and holding the STANDBY/ON button.
CAUTIO
When editing the playlist contents, if the SSD is ejected or the
external power is lost without performing any of the above
actions, changes to the playlist will be lost.
TASCAM DA-6400/DA-6400dp
11
DA-6400/DA-6400dp
Limitations to editing the playlist that is playing
0 Takes in the current folder can be assigned to or removed from the playlist. The entry that is currently being played, however, cannot
be changed.
0 Takes in other folders cannot be assigned to the playlist.
0 Entries cannot be inserted (INSERT), copied (COPY), moved (MOVE) or deleted (DELETE).
Playlist entry list screen
To open this screen, load or ENTER a playlist when the
BROWSE
screen is open. Alternatively, when the Home Screen is open, press the
MENU button while pressing the SHIFT button to open the menu, select
ENTRY LIST
, and press the MULTI JOG dial.
1 Playlist entry number
These icons show the entry numbers.
The status of the entry is shown as follows.
Icon Meaning INFO pop-up example
Current entry (entry is currently set for playback)
Normal entry with no problems
Entry that cannot be played back (take does not match the cur-
rent REC Fs setting or when a take that cannot be played back is
assigned)
File assigned to entry does not exist (take was deleted after be-
ing assigned to playlist or the playlist file alone was copied from
another folder, for example)
2 Entry with assigned take
This entry has a take assigned to it.
3 Entry without assigned take
This entry does not have a take assigned to it.
DA-6400/DA-6400dp
12
TASCAM DA-6400/DA-6400dp
Assigning takes to playlist entries (ASSIGN)
1. Load the playlist to which you want to assign takes, and
open the playlist entry list screen.
2. Turn the MULTI JOG dial to select the entry to which you
want to assign a take, and press the MULTI JOG dial to open
the menu.
3. Select
ASSIGN
, and press the MULTI JOG dial to open the
ASSIGN TAKE
screen.
4. Select the take that you want to assign on the
ASSIGN
TAKE
screen.
Select files and move between directories in the same way
as on the
BROWSE
screen.
NOTE
To cancel an ASSIGN operation, press the EXIT [PEAK CLEAR]
button to open the following pop-up message.
Press the MULTI JOG dial to return to the playlist entry list
screen.
Press the EXIT [PEAK CLEAR] button to close the pop-up
message.
5. Press the MULTI JOG dial to open the menu.
6. Select
ASSIGN
, and press the MULTI JOG dial to return to
the playlist entry list screen and assign the selected take to
the selected entry.
Inserting playlist entries (INSERT)
You can insert an empty entry.
1. Open the playlist entry list screen.
2. Turn the MULTI JOG dial to select the position where you
want to create an empty entry, and press the MULTI JOG dial
to open the menu.
3. Select
INSERT
, and press the MULTI JOG dial to insert an
empty entry at the selected position.
NOTE
If a take has been assigned to entry 999, which is the last pos-
sible playlist entry, the following pop-up message will appear.
Press the MULTI JOG dial to delete entry 999 and insert an
empty entry at the selected position.
Press the EXIT [PEAK CLEAR] button to close the pop-up
message without inserting an empty entry.
TASCAM DA-6400/DA-6400dp
13
DA-6400/DA-6400dp
Copying playlist entries (COPY)
The selected entry can be copied to a designated position.
1. Open the playlist entry list screen.
2. Turn the MULTI JOG dial to select the take you want to copy
(copy source entry), and press the MULTI JOG dial to open
the menu.
3. Select
COPY
, and press the MULTI JOG dial to open the
SE-
LECT DESTINATION
screen.
On this screen, the copy
source entry is shown with a yellow number icon and other
entries are shown with gray icons.
NOTE
To cancel a
COPY
operation, press the EXIT [PEAK CLEAR]
button to open the following pop-up message.
Press the MULTI JOG dial to return to the playlist entry list
screen.
Press the EXIT [PEAK CLEAR] button to close the pop-up
message.
4. Turn the MULTI JOG dial to select the position to which you
want to copy the entry (copy destination entry).
5. Press the MULTI JOG dial to open the following pop-up con-
firmation message.
If the copy destination is an empty entry
If the copy destination already has an assignment
6. Press the MULTI JOG dial to to copy the selected entry (copy
source entry) to the designated entry (copy destination en-
try).
Press the EXIT [PEAK CLEAR] button to close the pop-up
message.
DA-6400/DA-6400dp
14
TASCAM DA-6400/DA-6400dp
Moving playlist entries (MOVE)
The selected entry can be moved to a designated position.
1. Open the playlist entry list screen.
2. Turn the MULTI JOG dial to select the entry you want to
move, and press the MULTI JOG dial to open the menu.
3. Select
MOVE
, and press the MULTI JOG dial to open the
MOVE ENTRY
screen.
On this screen, the entry to be moved is shown with a yellow
number icon and other entries are shown with gray icons.
NOTE
To cancel a
MOVE
operation, press the EXIT [PEAK CLEAR]
button to open the following pop-up message.
Press the MULTI JOG dial to return to the playlist entry list
screen.
Press the EXIT [PEAK CLEAR] button to close the pop-up
message.
4. Turn the MULTI JOG dial to select the position to which you
want to move the entry.
5. Press the MULTI JOG dial to move the selected entry to that
position.
Clearing playlist entry take assignments (CLEAR)
You can clear assigned takes from entries to make them empty.
1. Open the playlist entry list screen.
2. Turn the MULTI JOG dial to select the entry for which you
want to clear its take assignment, and press the MULTI JOG
dial to open the menu.
3. Select
CLEAR
and press the MULTI JOG dial to open the fol-
lowing pop-up confirmation message.
Press and hold the MULTI JOG dial to clear the selected entry,
making it empty.
Press the EXIT [PEAK CLEAR] button to close the pop-up
message.
TASCAM DA-6400/DA-6400dp
15
DA-6400/DA-6400dp
Deleting playlist entries (DELETE)
The selected entry can be deleted, moving following entries for-
ward.
1. Open the playlist entry list screen.
2. Turn the MULTI JOG dial to select the entry you want to de-
lete, and press the MULTI JOG dial to open the menu.
3. Select
DELETE
and press the MULTI JOG dial to open a pop-
up confirmation message.
4. Press and hold the MULTI JOG to delete the selected entry
and move the following entries forward.
Press the EXIT [PEAK CLEAR] button to close the pop-up
message.
Editing playlist entries (ADJUST)
This explains how to edit the playback starting and ending points
of playlist entries.
NOTE
When a take is assigned, the take beginning and end are set as
the starting and ending points by default.
1. Open the menu in one of the following ways.
1.1 Open the playlist entry list screen, turn the MULTI JOG
dial to select the entry you want to edit, and press the
MULTI JOG dial to open the menu.
1.2 On the Home Screen, select the entry you want to edit,
and press the MENU button while pressing the SHIFT
button to open the menu.
2. Select
ADJUST
, and press the MULTI JOG dial to open the
START/END POINT
screen.
3. The light blue part between the blue bars in the area at the
top of the
START/END POINT
screen shows the playback
area.
The blue t on the left side is the playback starting point.
The blue g on the right side is the playback ending point.
The bar that can be edited will blink red.
The green b shows the current playback position.
The white b icons show marks have been added to the en-
try.
DA-6400/DA-6400dp
16
TASCAM DA-6400/DA-6400dp
4. Operations on the
START/END POINT
screen are some-
what different than on other screens.
Control assignments are shown at the top right of the screen.
1 When the frame cursor is visible, turn the MULTI JOG dial
to move the cursor.
2 When the frame cursor is visible, press the MULTI JOG dial
to switch to the solid cursor.
3 When the solid cursor is visible, press the MULTI JOG dial
to switch to the frame cursor.
4 When the solid cursor is visible, turn the MULTI JOG dial
to change the setting at the cursor position.
Turn the MULTI JOG dial while pressing and holding the
SHIFT button to make large setting changes.
However, the solid cursor is always visible on
RESET>>
and
<<CURRENT
. Turning the MULTI JOG dial will move
the cursor, and pressing the MULTI JOG dial will execute
the
RESET>>
or
<<CURRENT
operation.
With
RESET>>
, press the MULTI JOG at the
START
line
to reset to the beginning of the take or at the
END
line to
reset to the end of the take.
In either case, a confirmation pop-up message will appear
before resetting. Press the MULTI JOG dial to reset it.
With
<<CURRENT
, press the MULTI JOG dial to capture
the current playback position to a cursor line.
NOTE
Editing operations are also possible using a USB keyboard.
o Press the ENTER key to switch between the frame cursor
and solid cursor.
o Use the up and down cursor keys to change settings.
o Use the left and right cursor keys to move the cursor.
o Numbers can be input when the solid cursor is on a numer-
ical value.
5 Use transport operations on the
START/END POINT
screen to conduct rehearsal playback.
o Use the . and / buttons to move between the
file start, the
Start Point
, the
End Point
and the
file end. Otherwise, transport operations are as usual.
o If you change the
Start Point
, the playback position
will move to that point. If it is changed during playback,
playback will continue after moving to this playback po-
sition.
o If you change the
End Point
, the playback position
will move to 2 seconds before that point. If it is changed
during playback, playback will continue after moving to
this playback position.
o Depending on the
PREVIEW
setting at the top right of
the screen, the content of rehearsal playback will be dif-
ferent.
Rehearsal playback when PREVIEW OFF
Press the 7 button to start playback from the cur-
rent position. Playback and movement are possible
outside the range between the
Start Point
and
the
End Point
.
Rehearsal playback when PREVIEW ON
Press the 7 button to start playback from the cur-
rent position. In this case, playback is only possible
inside the range between the
Start Point
and
the
End Point
. Movement outside this range is not
possible.
5. When done editing, press the EXIT button to return to the
original screen.
Recording in Playlist Mode
Recording is possible even when using Playlist Mode.
When a take is recorded, it is automatically added as the next en-
try after the highest numbered entry that has an assigned take in
the current playlist.
Example:
Playlist before recording
Playlist after recording
NOTE
If a take has been assigned to entry 999, which is the last play-
list entry, pressing the 0 [SPLIT] button will cause the follow-
ing pop-up message to appear. Recording will not be possible.
TASCAM DA-6400/DA-6400dp
17
DA-6400/DA-6400dp
Theater play function added
A theater play function has been added. This allows the addition of marks for the playback starting and ending points of each take and the
playback of the set parts of multiple takes in order.
Theater play settings
Settings are made with the
THEATER PLAY
item added to the
PLAY SETUP
menu page.
MODE
This sets the theater play operation mode.
Option
OFF
: This disables the theater play function.
ON
: This enables the theater play function.
Theater play playback range
The playback range of each take is set with marks.
The mark points with the following names are the starting and
ending points in theater play.
Mark name Function
Start point mark
names
$START
When moving to this mark
from the $END of another
take, playback will continue
from this point.
$STANDBY
When moving to this mark
from the $END of another
take, playback will pause at
this point.
End point mark
names
$END
Take playback will end at this
mark, and it will move to the
first $START or $STANDBY
mark in the next take.
If the next take does not have
a $START or $STANDBY mark,
it will move to the beginning
of the next take and continue
playback.
No $END
Playback will continue to the
end of the take and continue
according to the operation
mode.
* Example of operation with the following settings
PLAY MODE
=
ALL
REPEAT MODE
=
ON
THEATER PLAY
=
ON
s
$STANDBY
s
$START
s
$STANDBY
s
$END
s
$END
s
$END
Take 3
$STANDBY, so pause
If
REPEAT MODE
is
ON
, return to $START or
$STANDBY in the first take.
If REPEAT MODE is OFF, stop .
Take 1
Take 2
Detected, so jump
Detected, so jump
$STANDBY, so pause
$START, so continue playing
Take range
Playback range
DA-6400/DA-6400dp
18
TASCAM DA-6400/DA-6400dp
Inputting names for theater play playback range
marks
Use the following procedures to easily input the names of marks
used for playback ranges in the theater play.
1. When the home screen is open, turn the MULTI JOG dial to
select the take for which you want to set the playback range.
2. Press the INFO button while pressing and holding the SHIFT
button to open the
MARK INFO
screen.
3. Select the mark that you want to set as the starting or ending
point for the playback range.
4. Press the MULTI JOG dial to open the menu, and select
EDIT NAME
.
5. Press the MULTI JOG dial to open a screen where you can
edit the name of the selected mark.
6. Turn the MULTI JOG dial to move the cursor to
PRESET
5,
and press the MULTI JOG dial to open a pull-up menu.
7. Turn the MULTI JOG dial to select the mark name you want
to input.
8. Press the MULTI JOG dial to input the selected mark name
and return to the
MARK INFO
screen.
NOTE
Rather than using
PRESET
5, you can input the characters
for
“$START
”, “
$STANDBY
or
“$END
the normal way.
Showing marks for theater play playback ranges
When the Home Screen is open, use the following procedure to
show marks for theater play playback ranges.
Mark name Mark
$START
(white t)
$STANDBY
(blue t)
$END
(blue g)
AUTO READY function added
An AUTO READY function has been added. After a take completes playback, this puts the unit into playback standby at the beginning of
the next take.
Settings are made with the
AUTO READY
item added to the
PLAY SETUP
menu page.
MODE
This sets the AUTO READY function operation mode.
Option
OFF
: This disables the AUTO READY function.
ON
: This enables the AUTO READY function.
TASCAM DA-6400/DA-6400dp
19
DA-6400/DA-6400dp
Support for timecode synchronized playback of all takes in the current folder
Timecode synchronized playback of all takes in the current folder is now supported.
Limitations
0 When in Playlist Mode,
CHASE MODE
cannot be set to
ON
.
0 If
CHASE MODE
is
ON
when a playlist is loaded and Playlist Mode is activated,
CHASE MODE
will automatically turn
OFF
.
0 When
CASCADE MODE
is
ON
,
CHASE MODE
cannot be turned
ON
.*
Setting timecode synchronized playback of multiple units
To use timecode synchronized playback with multiple units, input the same timecode into all units and set
CHASE MODE
to
ON
on all of
them.
Connection example
TIMECODED IN
TIMECODED IN
TIMECODED IN
TIMECODED IN
CASCADE MODE : OFF* / CHASE MODE : ON
CASCADE MODE : OFF* / CHASE MODE : ON
CASCADE MODE : OFF* / CHASE MODE : ON
CASCADE MODE : OFF* / CHASE MODE : ON
Timecode generator
* *Supported from firmware version 2.10. (See “Function explanation additions and changes” on page 35.)
Support for playback of WAV files in 32-bit PCM and 32-bit floating formats
Playback of WAV files in 32-bit PCM and 32-bit floating formats is now supported.
However, both formats will be converted to 24-bit PCM when played back.
NOTE
Playback is possible even when a single file contains a mixture of 16-bit PCM, 24-bit PCM 32-bit PCM and 32-bit float formats.
Take list sorting functions added
Sorting functions have been added that allow the take list to be arranged in take timecode and take name orders.
SORT BY NAME
and
SORT BY TC
functions have been added to the menu when the current folder is selected on the
BROWSE
screen.
DA-6400/DA-6400dp
20
TASCAM DA-6400/DA-6400dp
Home Screen menu functions added
When the Home Screen is open, pressing the MENU button while pressing the SHIFT button now opens a menu with operations for the
current take or playlist.
The menu items shown in Take List Mode are as follows.
Menu item Contents
TAKE LIST
Open the current folder list on the
BROWSE
screen.
INFO
Open a pop-up message with information about the current take.
RENAME
Open a screen where you can change the name of the current take.
EDIT TC
Open a screen where you can edit the timecode of the current take.
DELETE
Delete the current take.
CANCEL
Close the menu.
The menu items shown in Playlist Mode are as follows.
Menu item Contents
ENTRY LIST
Open the entry list screen for the current playlist.
ADJUST
Open the
ADJUST
screen for the current playlist.
INFO
Open a pop-up message with information about the current playlist entry.
SAVE AS
Name and save the current playlist file.
CANCEL
Close the menu.
NOTE
i If no SSD or hard disk drive is loaded, the following pop-up message will appear and the menu will not open.
i Menu items that cannot be used are shown with gray characters.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Tascam DA-6400 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI