Kodak M35 User manual

Publication No. 981777

September 1992

Supersedes 635819 and 635040

10/87 and 12/87

Service Manual

for the

KODAK

M35 and M35A

X-OMAT Processors

H112_0089AC

 Eastman Kodak Company, 1992

PLEASE NOTE

The information contained herein is based on the experience and knowledge relating to the subject matter gained by

Eastman Kodak Company prior to publication.

No patent license is granted by this information.

Eastman Kodak Company reserves the right to change this information without notice, and makes no warranty, express

or implied, with respect to this information. Kodak shall not be liable for any loss or damage, including consequential or

special damages, resulting from the use of this information, even if loss or damage is caused by Kodak’s negligence or

other fault.

This equipment includes parts and assemblies sensitive to damage from electrostatic discharge. Use

caution to prevent damage during all service procedures.

Related Publications for the M35 and M35A Processors

This publication is part of a series of instruction books that provide technical support information on the KODAK

M35 and M35A

X-OMAT Processors. It is recommended that these publications be kept in the binder provided.

If an individual book is misplaced or destroyed, order another copy from your Eastman Kodak Representative

using the Publication Part Numbers below.

981778

PARTS LIST

SERVICE

MANUAL

981777981158

MANUAL

OPERATOR

981157

SITE SPECS

INSTALLATION

INSTRUCTIONS

981159

981797

BINDER

COMPLETE

H112_9002BC

2 981777

Table of Contents

Description Page

Introduction........................................................................................................................................................1-1

Electrostatic Discharge.............................................................................................................................1-1

Processor Description...............................................................................................................................1-2

Special Tools..............................................................................................................................................1-2

Specifications and Data............................................................................................................................1-2

Service Procedures...........................................................................................................................................2-1

Feed Shelf...................................................................................................................................................2-3

Adjustment of the Feed Shelf...............................................................................................................2-3

Replacement of the Protective Material...............................................................................................2-3

Detector Switches......................................................................................................................................2-4

Adjustment of the Detector Switches...................................................................................................2-4

Replacement of the Detector Switches................................................................................................2-5

Crossover Assemblies ..............................................................................................................................2-6

Adjustment for Squareness..................................................................................................................2-6

Installation of a New Guide Shoe ........................................................................................................2-6

Rack Assemblies .......................................................................................................................................2-7

Adjustment for Squareness..................................................................................................................2-7

Drive Chain...........................................................................................................................................2-8

Adjustment of the Tension on the Drive Chain.............................................................................2-8

Replacement of the Drive Chain...................................................................................................2-8

Turnaround Assembly...........................................................................................................................2-9

Adjustment for Squareness...........................................................................................................2-9

Disassembling the Turnaround Assembly.....................................................................................2-10

Replacement of the B Roller.........................................................................................................2-11

Checking the Guide Shoes ...........................................................................................................2-11

Replacement of the A Rollers.......................................................................................................2-12

Replacement of the Resilient Drive Roller in the Developer and Fixer Racks ...................................2-13

Replacement of the Resilient Rollers in the Wash Rack.....................................................................2-14

Dryer Rack............................................................................................................................................2-15

Adjustment for Squareness...........................................................................................................2-15

Replacement of the Drive Roller...................................................................................................2-16

Main Drive...................................................................................................................................................2-17

Adjustment of the Main Drive Chain....................................................................................................2-17

Alignment of the Main Drive Motor ......................................................................................................2-18

Replacement of the Main Drive Shaft, Worm Gears, or Bearing Blocks............................................2-19

Dryer Heater ...............................................................................................................................................2-21

Adjustment of the Dryer Temperature..................................................................................................2-21

Replacement of the Blower Assembly .................................................................................................2-22

Replacement of the Dryer Heater or the Heater Core ........................................................................2-25

Plumbing.....................................................................................................................................................2-28

Adjustment of the Developer Temperature..........................................................................................2-28

Replacement of the Developer Heater.................................................................................................2-30

Replacement of the Developer Over-temperature Thermostat............................................................2-32

Replacement of the Developer Thermistor ..........................................................................................2-33

981777 3

Description Page

Replacement of the Heat Exchangers .................................................................................................2-34

Recirculation Pump...............................................................................................................................2-36

Replacement of the Recirculation Pump.......................................................................................2-36

Replacement of the O-Ring...........................................................................................................2-37

Replenishment Pump ...........................................................................................................................2-38

Replacement of the Replenishment Pump ...................................................................................2-38

Adjustment of the Replenishment Pumps.....................................................................................2-39

Adjustment of the Replenishment Flow Rates in M35A Processors with Serial No. 10,000

and Above or in M35 Processors with Serial No. 35,000 and Above......................................2-40

Adjustment of the Replenishment Flow Rates in M35A Processors with Serial No. 8940 and

Below or in M35 Processors with Serial No. 3760 and Below.................................................2-42

Plumbing Circulation Diagrams, M35 and M35A Processors..............................................................2-43

Periodic Maintenance .......................................................................................................................................3-1

General Information...................................................................................................................................3-1

Lubrication Table ..................................................................................................................................3-1

Periodic Maintenance Schedule...........................................................................................................3-2

Roller Transport.........................................................................................................................................3-3

Detector Switches.................................................................................................................................3-3

Detector Crossover Assembly..............................................................................................................3-3

Crossover Assemblies..........................................................................................................................3-4

Rack Assemblies ..................................................................................................................................3-5

Turnaround Assemblies........................................................................................................................3-6

Dryer............................................................................................................................................................3-8

Main Drive...................................................................................................................................................3-9

Plumbing.....................................................................................................................................................3-10

General .................................................................................................................................................3-10

Recirculation Pumps.............................................................................................................................3-11

Developer Filter ....................................................................................................................................3-12

Temperature of the Developer .............................................................................................................3-13

Chemical Replenishment......................................................................................................................3-15

Interlock Switch .........................................................................................................................................3-16

Correcting Difficulties.......................................................................................................................................4-1

Diagrams............................................................................................................................................................5-1

Publication Change Table................................................................................................................................6-1

4 981777

Introduction

Electrostatic Discharge

Overview Preventive Measures

ESD--electrostatic discharge--is a primary source of: • Always look for an ESD warning label before doing

any procedure involving static-sensitive

components such as circuit boards. All

• product downtime

static-sensitive components are marked with bright

• lost productivity

graphic labels, which frequently include

• costly repairs

instructions. Follow all label instructions.

• If the work area is carpeted, spray the carpet with

While one cannot feel a static charge of less than

an antistatic solution. In low-humidity

3,500 volts, as few as 30 volts can damage or

environments, spray carpets periodically with an

destroy essential components in electronic

antistatic preparation, available at local stores.

equipment.

• Wear a grounding strap when handling

Effective ESD control requires following these static-sensitive components. Always make certain

guidelines. that the clip remains attached to a properly

grounded, unpainted, clean surface.

• Repair static-sensitive components at an

Personnel Awareness

ESD-protected work station or use a portable

grounding mat. For help in setting up an

Everyone within the organization needs to be aware

ESD-protected work station, contact your Kodak

of ESD, because partial ESD control is no ESD

representative.

control at all. Please note:

• When moving static-sensitive components from one

area to another, insert and transport the

• ESD is a primary source of

components in ESD-protective packaging.

frustrating equipment failures and

Transparent antistatic bags are available from a

intermittent malfunctions.

variety of manufacturers and will help shield

• ESD affects productivity and

components from ESD damage.

profitability.

• ESD can be controlled.

General Precautions

• Do not store trash near static-sensitive equipment.

• Do not place plastic materials near electronic

components. Trash-can liners and styrofoam cups

generate static electricity, which can damage or

destroy electronic components.

981777 1-1

Processor Description

The KODAK

M35 and M35A

X-OMAT Processors

are designed to process medical x-ray film in either

sheets or rolls. This tabletop processor is

self-threading and has a 3-rack processing section

with a dryer.

Special Tools

The following special tools are necessary for some of

the service procedures in this manual.

• TL-3230 Sealant

• TL-2244 Motor Oil, 1-oz Tube

• TL-2324 Motor Oil, 12-oz Tube

H112_0089AC

• TL-1481 Potentiometer Adjusting Tool

• 761217 Thermometer

Specifications and Data

Film Sizes Wash Water

The water for washing the film comes from the

• 10 - 35 cm (4 - 14 in.) width

customer’s water supply. The FLOW CONTROL

• 10 cm (4 in.) minimum length

VALVE regulates the usage at approximately 1 litre

• 4.6 m (15 ft) maximum length

(⁄

1

4

gal) per minute.

Dryer

Processor Speed

The processor has a roller transport dryer with

approximately slotted AIR TUBES. A thermostat controls the

76 cm (30 in.) per minute

temperature from 46 - 65°C (115 - 150°F).

Control of the Solution Temperature

Power Requirements

The temperature of the developer is adjustable from

The M35 Processor uses 200, 208, 220, or 240

approximately 30 to 46°C (85 to 115°F). The

volts with a single-phase, 2-wire plus earth ground or

temperature of the fixer is not controlled by

220 or 240 volts with a 2-phase, 3-wire plus earth

adjustment.

ground and 50/60 Hz.

The M35A Processor uses 120 volts and a

single-phase, 2-wire plus an earth ground and

50/60 Hz.

1-2 981777

Dimensions Main Drive Motor

The MAIN DRIVE MOTOR is an open-frame

Height: 52 cm (20.5 in.)

gearhead motor with an automatic thermal overload

Width: 67.3 cm (26.5 in.)

protector.

Depth: 1.27 metres (50 in.) overall,

from the end of the FEED SHELF to

the end of the RECEIVING BIN

Blower Motor

Weight: approximately 90 kg (200 pounds)

The BLOWER MOTOR is equipped with an

empty

automatic thermal overload protector.

Films and Chemicals

Capacity of the Tanks with Racks Installed

The KODAK

M35 and M35A

X-OMAT Processors

The developer, fixer, and wash tanks each contain

accept film that can be processed in KODAK

RP

7.8 litres (2.07 gallons).

X-OMAT Chemicals.

The RECIRCULATION PUMP for the developer and

Site Specifications

the fixer consists of a thermally protected MOTOR

that operates two magnetic, centrifugal pumps.

Publication No. 981157 contains the site

specifications for the KODAK

M35 and M35A

X-OMAT Processors.

Replenishment Pump

The replenishment system uses a positive

displacement BELLOWS PUMP, designed for

accurate delivery of replenishment solutions

regardless of the solution level in the REPLENISHER

TANKS.

981777 1-3

BLANK PAGE

1-4 981777

Service Procedures

Table of Contents

Description Page

Feed Shelf..........................................................................................................................................................2-3

Adjustment of the Feed Shelf......................................................................................................................2-3

Replacement of the Protective Material ......................................................................................................2-3

Detector Switches.............................................................................................................................................2-4

Adjustment of the Detector Switches ..........................................................................................................2-4

Replacement of the Detector Switches.......................................................................................................2-5

Crossover Assemblies .....................................................................................................................................2-6

Adjustment for Squareness .........................................................................................................................2-6

Installation of a New Guide Shoe................................................................................................................2-6

Rack Assemblies...............................................................................................................................................2-7

Adjustment for Squareness .........................................................................................................................2-7

Drive Chain..................................................................................................................................................2-8

Adjustment of the Tension on the Drive Chain....................................................................................2-8

Replacement of the Drive Chain..........................................................................................................2-8

Turnaround Assembly..................................................................................................................................2-9

Adjustment for Squareness..................................................................................................................2-9

Disassembling the Turnaround Assembly............................................................................................2-10

Replacement of the B Roller................................................................................................................2-11

Checking the Guide Shoes...................................................................................................................2-11

Replacement of the A Rollers ..............................................................................................................2-12

Replacement of the Resilient Drive Roller in the Developer and Fixer Racks...........................................2-13

Replacement of the Resilient Rollers in the Wash Rack............................................................................2-14

Dryer Rack...................................................................................................................................................2-15

Adjustment for Squareness..................................................................................................................2-15

Replacement of the Drive Roller..........................................................................................................2-16

Main Drive..........................................................................................................................................................2-17

Adjustment of the Main Drive Chain ...........................................................................................................2-17

Alignment of the Main Drive Motor..............................................................................................................2-18

Replacement of the Main Drive Shaft, Worm Gears, or Bearing Blocks ...................................................2-19

Dryer Heater.......................................................................................................................................................2-21

Adjustment of the Dryer Temperature.........................................................................................................2-21

Replacement of the Blower Assembly.........................................................................................................2-22

Replacement of the Dryer Heater or the Heater Core................................................................................2-25

Plumbing............................................................................................................................................................2-28

Adjustment of the Developer Temperature .................................................................................................2-28

Replacement of the Developer Heater........................................................................................................2-30

Replacement of the Developer Over-temperature Thermostat...................................................................2-32

Replacement of the Developer Thermistor..................................................................................................2-33

Replacement of the Heat Exchangers ........................................................................................................2-34

Recirculation Pump......................................................................................................................................2-36

Replacement of the Recirculation Pump..............................................................................................2-36

Replacement of the O-Ring..................................................................................................................2-37

981777 2-1

Description Page

Replenishment Pump...................................................................................................................................2-38

Replacement of the Replenishment Pump...........................................................................................2-38

Adjustment of the Replenishment Pumps............................................................................................2-39

Adjustment of the Replenishment Flow Rates in M35A Processors with Serial No. 10,000 and

Above or in M35 Processors with Serial No. 35,000 and Above ....................................................2-40

Adjustment of the Replenishment Flow Rates in M35A Processors with Serial No. 8940 and

Below or in M35 Processors with Serial No. 3760 and Below........................................................2-42

Plumbing Circulation Diagrams, M35 and M35A Processors.....................................................................2-43

2-2 981777

Feed Shelf

Adjustment of the Feed Shelf

[1] Adjust the height of the FEED SHELF to

approximately 1.5 mm (0.06 or 1/16 in.) below

the NIP of the DETECTOR CROSSOVER

ROLLERS.

(a) Loosen the 4 SCREWS.

(b) Adjust the FEED SHELF for the correct

height by moving the FEED SHELF up

or down.

(c) Insert a sheet of 35 x 43 cm film into

the NIP of the DETECTOR

CROSSOVER ROLLERS.

[2] Use the edges of the film to align the FILM

GUIDE with the DETECTOR CROSSOVER

ROLLERS for squareness.

1.5 mm

(0.06 in.)

H112_0090AA

H112_0090ACA

GUIDE

FILM

SHELF

FEED

SCREW (4)

ROLLERS

CROSSOVER

DETECTOR

NIP

film entry path

[3] Tighten the 4 SCREWS.

Replacement of the Protective Material

[1] Remove the 4 SCREWS and the FEED IMPORTANT

SHELF.

Be sure the FEED SHELF is dry before

[2] Remove all of the existing PROTECTIVE

installing the PROTECTIVE

MATERIAL and adhesive from the FEED

MATERIAL.

SHELF.

[4] Install the new PROTECTIVE MATERIAL.

[3] Clean the FEED SHELF with a damp sponge.

[5] Install the FEED SHELF and adjust if

necessary. See the above procedure.

H112_0113BA

H112_0113BCA

FEED SHELF

SCREW (4)

MATERIAL

PROTECTIVE

981777 2-3

Detector Switches

(c) Insert a 5 x 7 inch sheet of film.

Adjustment of the Detector Switches

(d) Move the drive side DETECTOR

SWITCH until the REPLENISHMENT

PUMP activates.

(e) Check that the REPLENISHMENT

Moving parts.

PUMP stops in 3 seconds after you

remove the sheet of film.

[1] Remove the TOP COVER.

[6] Adjust the clearance between the MAGNET

[2] Check the DEVELOPER RACK and the

and the DETECTOR SWITCH if necessary.

DETECTOR CROSSOVER ASSEMBLY for

(a) Loosen the SCREW.

squareness. See pages 2-6 and 2-7.

(b) Move the ROCKER ARM.

[3] Install the DEVELOPER RACK and the

DETECTOR CROSSOVER ASSEMBLY.

(c) Tighten the SCREW.

[4] Set the clearance between the MAGNET and

[7] Do steps 4 - 6 to adjust the DETECTOR

the DETECTOR SWITCH on the drive side to

SWITCH on the non-drive side.

1.6 mm (0.06 or 1/16 in.).

[8] Install the TOP COVER.

[5] Check the clearance between the MAGNET

[9] Check that the REPLENISHMENT PUMP

and the DETECTOR SWITCH:

does not operate unless you feed film.

(a) Energize the processor.

(b) Lift the top DETECTOR ROLLER.

1.6 mm

(0.06 in.)

H112_0112BA

H112_0112BCA

SWITCH (2)

DETECTOR

MAGNET (2)

SCREW

SWITCH (2)

DETECTOR

ROLLER

DETECTOR

ROCKER ARM

ROCKER

ARM

Adjusting the Detector Switches

2-4 981777

[4] Connect the new SWITCH CABLE.

Replacement of the Detector Switches

[5] Install the:

• new DETECTOR SWITCH

• 2 WASHERS

Dangerous voltage.

• 2 LOCK WASHERS

• 2 SCREWS

[1] Disconnect the main power.

• new WIRE TIES

[2] Remove the:

[6] Connect the main power.

• 2 SCREWS

[7] Do the adjustment procedure if necessary.

• 2 LOCK WASHERS

See page 2-4.

• 2 WASHERS

• WIRE TIES, not shown

[3] Disconnect the SWITCH CABLE from the

ELECTRICAL BOX.

H112_0067BA

SCREW (2)

DETECTOR

SWITCH

WASHER (2)

LOCK WASHER (2)

H112_0067BCA

Replacement of the Detector Switch

981777 2-5

Crossover Assemblies

Adjustment for Squareness

NOTE

Use this procedure to check the

squareness of any of the

CROSSOVER ASSEMBLIES.

[1] Remove the CROSSOVER ASSEMBLY from

the processor.

[2] Place the CROSSOVER ASSEMBLY on a

smooth, flat surface.

[3] Loosen the 2 NUTS on the 2 TIE RODS.

[4] Check that the 2 SIDE PLATES touch the flat

surface evenly.

[5] Tighten the 2 NUTS.

Installation of a New Guide Shoe

[1] Remove the existing GUIDE SHOE SCREWS

and GUIDE SHOE.

[2] Install the GUIDE SHOE with the LONG TIPS

in the direction of film travel.

[3] Install the 2 GUIDE SHOE SCREWS.

H048_0155CA

H048_0155CCB

GUIDE

SHOE

LONG

TIP

SHORT

TIP

NOTE

Installing a Guide Shoe

The GUIDE SHOES have no adjustment procedures.

H112_0056BA

H112_0056BCA

TIE ROD

NUT

SIDE PLATE

NUT

LONG TIP

TIE ROD

SCREW (2)

GUIDE SHOE

PLATE

SIDE

2-6 981777

Rack Assemblies

Adjustment for Squareness

NOTE

Use this procedure to check the

squareness of any of the RACK

ASSEMBLIES.

[1] Remove the RACK ASSEMBLY from the

processor.

[2] Place the RACK ASSEMBLY on a smooth,

flat surface.

[3] Loosen the SCREWS on the ends of the

3 TIE RODS.

[4] Check that the 2 SIDE PLATES touch the flat

surface evenly.

[5] Tighten the SCREWS.

smooth, flat surface

H112_0110AA

H112_0017AC

H112_0017ACA

SIDE PLATE

SCREW (2)

TIE ROD

SIDE PLATE

Adjusting a Rack Assembly for Squareness

981777 2-7

Drive Chain

Adjustment of the Tension on the Drive Chain

[1] Check that the DRIVE CHAIN is wet with

solution.

[2] Check that the RACK ASSEMBLY is at

approximately the same temperature as the

solutions in the tanks, to assure that the

DRIVE CHAIN is the correct length.

[3] Loosen the 4 HOLDING SCREWS.

[4] Hold the RACK ASSEMBLY above the work

surface until gravity tightens the DRIVE

CHAIN around the TURNAROUND

ASSEMBLY.

[5] Rotate the DRIVE GEAR one full turn.

[6] Tighten the 2 HOLDING SCREWS on the

drive side first.

[7] Place the RACK ASSEMBLY on the work

surface.

[8] Rotate the ADJUSTING SCREWS until the

distance between the SIDE PLATE of the

RACK and the SIDE PLATE of the

TURNAROUND ASSEMBLY on the non-drive

side is equal to the distance between the

2 SIDE PLATES on the drive side.

[9] Tighten the 2 HOLDING SCREWS on the

non-drive side.

NOTE

Remove LINKS from the DRIVE

CHAIN if necessary to provide the

correct length. See steps 1 - 5.

H112_0109CA

H112_0109CCA

DRIVE CHAIN

HOOK

LINK

ASSEMBLY

TURNAROUND

SCREW (4)

HOLDING

SCREW (4)

ADJUSTING

GEAR

DRIVE

SIDE PLATE

Replacement of the Drive Chain

[1] To open the existing DRIVE CHAIN, insert a [3] Pull the existing DRIVE CHAIN through the

screwdriver under the HOOKS of a LINK. RACK ASSEMBLY until the new DRIVE

Rotate the screwdriver if necessary. CHAIN is in the correct position.

[2] Attach the new DRIVE CHAIN to the existing [4] Disconnect the existing DRIVE CHAIN from

DRIVE CHAIN with the HOOKS in the the new DRIVE CHAIN.

direction of travel and the openings of the

[5] Connect the ends of the new DRIVE CHAIN.

LINKS outward. See the illustration.

[6] Do the Drive Chain Adjustment above.

2-8 981777

[2] Loosen the 4 HOLDING SCREWS.

Turnaround Assembly

[3] Rotate the 4 ADJUSTING SCREWS the same

amounts to move the TURNAROUND

Adjustment for Squareness

ASSEMBLY up or down.

NOTE

[4] Check that the 2 SIDE PLATES of the

TURNAROUND ASSEMBLY touch the flat

The illustration shows a DEVELOPER

surface evenly.

RACK ASSEMBLY; however, the

procedure is the same for

[5] Tighten the 4 HOLDING SCREWS.

disassembling all the RACK

ASSEMBLIES.

[1] Place the RACK ASSEMBLY on a smooth,

flat surface.

H112_0096DA

H112_0096DCA

SCREW (4)

ADJUSTING

SCREW (4)

HOLDING

SIDE PLATE (2)

Assembly

Turnaround

Upper Rack Assembly

Rack and Turnaround Assemblies

981777 2-9

Disassembling the Turnaround Assembly

[1] Remove the: [3] Remove the:

• EXIT GUIDE SHOE and the BRACKETS • 4 HOLDING SCREWS

• ROLLER above the GUIDE SHOE • CHAIN from the B ROLLER

• 2 SPRINGS and LOCKING PLATE from the • TURNAROUND ASSEMBLY

TURNAROUND ASSEMBLY

• 2 A ROLLERS

[2] From the non-drive side, pull the SHAFT from

the B ROLLER.

H112_0075EA

B ROLLER

A ROLLER

SHAFT

CHAIN

HOLDING

SCREW (4)

LOCKING

PLATE

SCREW (2)

BRACKET (2)

A ROLLER

EXIT

GUIDE

SHOE

H112_0075ECA

SPRING

(2)

Disassembling the Turnaround Assembly

2-10 981777

Replacement of the B Roller

[1] See the illustration on page 2-10. Remove

the:

• TURNAROUND ASSEMBLY from the RACK

• 2 SPRINGS

• LOCKING PLATE

• 2 A ROLLER ASSEMBLIES

• 2 SCREWS

• 2 BRACKETS

• EXIT GUIDE SHOE

• SHAFT, THRUST WASHERS, and the

BEARING from the B ROLLER

[2] See page 2-10. Install the:

• new B ROLLER, THRUST WASHERS, and

BEARING onto the SHAFT

• 2 SCREWS

• 2 BRACKETS

• EXIT GUIDE SHOE

• 2 A ROLLER ASSEMBLIES

• LOCKING PLATE

• 2 SPRINGS

• TURNAROUND ASSEMBLY onto the RACK

[3] Check that the DRIVE CHAIN has the correct

tension. See page 2-8 if adjustment of the

DRIVE CHAIN is necessary.

Checking the Guide Shoes

[1] Check that the LONG TIPS are in the

direction of film travel.

H048_0155CA

H048_0155CCB

GUIDE

SHOE

LONG

TIP

SHORT

TIP

Checking the Guide Shoes

981777 2-11

Replacement of the A Rollers

NOTE [2] Install the:

• new A ROLLER on the SHAFT

Each TURNAROUND ASSEMBLY has

• A ROLLER in the TURNAROUND

2 A ROLLERS.

ASSEMBLY

[1] Remove the:

• LOCKING PLATE

• 2 SPRINGS • 2 SPRINGS

• LOCKING PLATE

[3] Check that all the GEARS in the

• SCREW TURNAROUND ASSEMBLY engage.

• A ROLLER from the SHAFT

H112_0075EA

GEAR

SHAFT

A ROLLER

GEAR

SHAFT

A ROLLER

GEAR

SPRING (2)

LOCKING

PLATE

SCREW

H112_0075ECB

Replacement of the A Rollers

2-12 981777

Page is loading ...

Kodak M35 User manual

This manual is also suitable for

Kodak M35 User manual

Related papers

Other documents