WisyCom MTP30 Quick User Manual

Type
Quick User Manual
WISYCOM s.r.l. - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) - Italy - MTP30-eng-b04.doc
Tel. (Ph.). +39 0424 382605 - Fax +39 0424 382733 - http:// www.wisycom.com
- e-mail: [email protected]
WIRELESS MICROPHONE SYSTEMS
MTP30
Ultra-lite Wireless Professional Transmitters
UMain Features
Up to 96 MHz bandwidth in 470/870 MHz range
Enhanced robustness against inter-modulation and antenna
performances:
Æ RF part with pass-band filter and circulator (option)
Miniature design with flexible pcb (no connectors)
for extended reliability
Ultra-light metal alloy body (80g without batteries)
ENR compander system
Battery:
- 2 AA Alkaline or rechargeable NiMH
Autonomy:
> 10h @ 50mW output power
> 14h @ 10mW output power
Infrared interface for management and firmware update
Easy and quick to setup thru an Oled display gain/freq button and a
joggle selector
Extended regulation on Mic input gain: 80dB in 2dB step
Max input level 26dBu (15.5 V clipping) to connect directly to mixers
and instruments
UGeneral Description
“MTP30 is an extremely small and light pocket
transmitters especially designed for professional
wireless microphone applications”
Very easy and quick to use thanks to OLED display and gain/freq
button and an easy joggle selector.
MTP30 benefits also of the latest Wisycom RF technology along with
an enhanced robustness against noise and inter-modulation
(available also with the RF circulator option).
Subject to change without notice
WISYCOM s.r.l. - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) - Italy - MTP30-eng-b04.doc
Tel. (Ph.). +39 0424 382605 - Fax +39 0424 382733 - http:// www.wisycom.com
- e-mail: [email protected]
MTP30 470 ÷ 870 MHz UHF HAND-HELD TRANSMITTER
T
T
E
E
C
C
H
H
N
N
I
I
C
C
A
A
L
L
S
S
P
P
E
E
C
C
I
I
F
F
I
I
C
C
A
A
T
T
I
I
O
O
N
N
S
S
1
Switchable channels 320 allocated by 8 groups of 40 channels (in the 470 ÷ 870 MHz range), quickly selectable with dedicated buttons
2
Switching window 70 to 100 MHz, depending on band (see below code table):
1 470-550 MHz 2 520-590 MHz 3 560-660 MHz 4 630-730 MHz 5 700-800 MHz 6 770-870 MHz
3
Frequencies Quartz PLL frequency synthesizer circuit (25 kHz step)
Frequency stability
± 2,5 ppm (in the rated temperature range)
± 2.5 kHz (in the rated temperature range)
Temperature range -10 ÷ +55 °C
Max RF power
50 mW (ERP) when high power selected
10 mW (ERP) when low power selected
Spurious emissions < 2 nW
Modulation wideband FM, with 50 µs pre-emphasis
Nominal deviation ±40 kHz (Peak deviation = ±56 kHz)
Telemetry feature MTP30 transmits also a digitally modulated sub-carrier, suitable for:
tone-squelch operating remote battery monitoring optional PTT (push to talk) operation
AF input connector Configurable on ‘mic’ display menu in 3 options:
’2 wires’: Æ gain selectable -40 ÷ +40, no bias voltage
‘2 wires + bias’: Æ gain selectable -20 ÷ +40, 5.5 V bias voltage (4k7 internal resistance)
‘3 wires + bias’: Æ gain selectable -20 ÷ +40, 5.5 V bias voltage (4k7 internal resistance)
AF input level 80 dB adjustable range from -60 dBu (775 uV) to 20 dBu (7.75 V) at nominal deviation (1 kHz), adjustable in 2 dB steps
Max. input level +26 dBu (15.5 V) at clipping, +20 dBu (7.75 V) at nominal level
Noise-Reduction ENR (Wisycom Extended-NR), with independent Attack-time and Recovery-time
AF bandwidth
45 Hz ÷ 21 KHz (3dB)
55 Hz ÷ 20 KHz (1dB)
Distortion < 0.3 % (0.15 % typ.)
Signal-to-noise ratio
typ. 115 dB (A)
rms
with 40 kHz deviation
typ. 121 dB (A)
rms
with 56 kHz deviation
Led Led indication with bicolor led (red & green) on wireless power switch:
Wireless transmission status: GREEN on/off Battery lifetime status: GREEN -
UsteadyU (> 25%)
-
Uslowly blinkingU (< 25%) - Uquickly blinkingU (<12%)
Modulation peek (if activated): RED Ptt status: RED if active
Display High contrast OLED (Organic light-emitting diode) display (96 x 36 pixels)
8 step battery lifetime indication: 7
UbarsU (100%-87%-75%-63-50%-38%-25%) and “Uempty barU” quickly blinking (12%
remaining
)
PTT function Pin 3 of the AF connector can be setup to an external push button
Power supply 2 AA size batteries (Alkaline, rechargeable NiMH)
orking
Battery life
(2 AA alkaline)
approx. 10 hours @ 50mW continuous working
approx. 14 hours @ 10mW continuous w
Dimensions th-Depth) 73 x 61 x 17.5 mm (Height-Wid
Weight Approx 80 g. without batteries
UOPTION CODE MTP3
0
-
X
-Y-Z:
AUDIO CONNECTOR (-X)
L 3 PIN LEMO CONNECTOR
COLOR (-Y)
C body color "champagne"
B body color "matt black"
FREQUENCY RANGE (-Z)
1 470-550 MHz
2 520-590 MHz
3 560-660 MHz
4 630-730 MHz
5 700-800 MHz
6 770-870 MHz
EXAMPLE: MTP30 LB4 is 3 pin LEMO connector, color matt
black, and 630-730 MHz frequency range
Subject to change without notice
WISYCOM s.r.l. - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) - Italy - MTP30-eng-b04.doc
Tel. (Ph.). +39 0424 382605 - Fax +39 0424 382733 - http:// www.wisycom.com
- e-mail: [email protected]
0BMTP30 QUICK USER GUIDE
MTP30 is a professional pocket transmitter especially designed for broadcast/high quality
applications.
1. 1BOPERATION
MTP30 is composed by a main body made up of light metal alloy.
(1) Switch to enable wireless transmission, it also indicates
the battery status and peak/mute operation (with PTT).
(2) In order to allow front visibility same colour information
on (1) is replicated with this LED.
(3) Oled display for transmitter setup
(4) <ch>, <gain> and 3 positions <selector>
(5) Battery holder
(6) Cover (to open push side buttons)
1.1 2BLED INDICATIONS
Led indication with bicolor led (red & green) on wireless power switch (1) and in front led (2):
- Wireless transmission status: green when wireless on.
- Battery status: green steady, slowly blinking (< 25%), quickly blinking (<12%).
- Modulation peek (if activated): red.
- Ptt status: red if active (push to talk “pushed”).
1.2 3BBATTERIES
MTP30 is working with 2 AA alkaline or NiMH batteries (select correct type on setup controls).
Battery status can be checked on internal OLED display or looking to LED status on power
switch (see 1.1).
1.2.1
6BUBATTERY SUBSTITUTION
Open transmitter cover and insert batteries following polarity indicated.
1.3 4BPOWERING UP
Move the wireless power switch (3) in “I” position to activate wireless transmission: a green
LED lights up (blinking when battery is low! See 1.1)
Turn on wireless:
Move the Wireless power switch in
“I” position: switch becomes green
(red indicate PTT/MUTE).
A green blinking gives you
indications on battery status.
Open MIC Body:
Push the side buttons and flip down
the cover, to access internal setup
controls and batteries.
Front LED color is
the same of
power switch.
1
2
3
5
6
4
Turn on display:
Push <select switch>
and hold it.
WISYCOM s.r.l. - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) - Italy - MTP30-eng-b04.doc
Tel. (Ph.). +39 0424 382605 - Fax +39 0424 382733 - http:// www.wisycom.com
- e-mail: [email protected]
1.4 5BSETUP CONTROLS
Open transmitter Body to access the
“display and controls” area (fig. 3):
A) Graphics Display (OLED)
B) Channel selection button (ch)
C) MIC gain setup button (gain)
D) 3 position selector (- / click / +)
Fig. 3
1.4.1 7BULED POWER UP (OLED IS IN OFF CONDITION)
Pushing down selector (click), oled turns on. A first menu with serial NO and brand logo is
display, then <status> menu enters automatically.
Pushing and holding selector (click) > 2 sec, serial NO menu is displayed till (-/+) is selected.
1.4.2
8BUOLED POWER DOWN (OLED IS IN ON CONDITION)
Pushing and holding selector (click) > 2 sec, display is turned off.
Display turns off automatically after 15 sec, unless in <irda> menu or in <audio> menu (with
audio level < 5% from nominal).
1.4.3
9BUDISPLAY MENU
Setup menu are accessed in sequence:
Æ <status> Æ <tuning> Æ <audio> Æ <mic> Æ <rf power> Æ <other> Æ <irda> Æ <lock> Æ
Using <+/-> selector all menus can be accessed in sequence
Push <click> to enter edit mode:
<+/-> to setup field
Æ <click> again to confirm changes and exit.
Æ exit without confirmation if no button is pressed after a few seconds time out.
1.4.3.1 10B<start up> menu
This menu is displayed during power up for few seconds:
Keep selector pushed to hold this menu.
Main information are:
Æ Product name – software version
Æ Brand name
Æ Transmitter bandwith
Æ Serial No:
1.4.3.2 11B<status> menu
This is the first menu displayed after power up.
Major info are displayed:
- Current channel/group (i.e. CH:00 GR:1)
- Current frequency (i.e. 770.000 MHz)
- Mic gain (i.e. -04) and high pass filter (i.e. FLAT)
- RF active, top right label RF (if present RF is on)
1.4.3.3 12B<tuning> menu
This menu can be entered by scrolling selector or using
Uquick
channel setupU buttons (<ch>).
In this menu current channel/group and frequencies can be setup.
Use the selector to change values (<+/->) and <click> to
confirm.
A
C
D
B
(- / click / +
Ch Gain
WISYCOM s.r.l. - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) - Italy - MTP30-eng-b04.doc
Tel. (Ph.). +39 0424 382605 - Fax +39 0424 382733 - http:// www.wisycom.com
- e-mail: [email protected]
1.4.3.4 13B<audio> menu
This menu can be entered by scrolling selector or using quick gain
setup buttons (<gain>).
To help proper audio gain setting, an audio bar is supplied (with
peak hold bar) Æ TRY TO SETUP TO HAVE A MAX PEAK HOLD
BAR CLOSE TO 100.
High pass audio filter can be setup with different preset values.
Use the selector to change values (<+/->) and <click> to
confirm.
UNOTE: while in this menu display is not automatically turned off.U
1.4.3.5 14B<mic> menu
This menu can be entered by scrolling selector.
Following Mic mode can be setup:
- 2 wired (PTT is possible)
- 2 wires + bias (PTT is possible)
- 3 wires + bias (no PTT)
Additional field to setup
- Phase: is audio phase can be 0/180 deg.
- PTT operation mode:Normal (pushing make a
remote switch)/Muting (pushing mute the audio)
Use the selector to change values (<+/->) and <click> to
confirm.
1.4.3.6 15B<rf power> menu
This menu can be entered by scrolling selector.
RF power can be setup to High (50 mW ERP) or Low (10 mW ERP).
Use the selector to change values (<+/->) and <click> to
confirm.
1.4.3.7 16B<others> menu
This menu can be entered by scrolling selector.
Power switch green LED brightness can be setup Æ LED light.
Modulation peak LED on power switch (become RED when audio
get close to saturation) can be enabled/disabled). Battery type can
be setup in Alkaline or NiMH.
1.4.3.8 17B<irda> menu
This menu can be entered by scrolling selector.
While is this menu MIC can be connected to IRDA for setup or
firmware upgrades.
UNOTE: while in this menu display is not automatically turned off.U
1.4.3.9 18B<lock> menu
This menu can be entered by scrolling selector.
Long pressing (2 sec.) selector button (click) it locks MTP30 in
transmission mode.
To unlock, long pressing (2 sec.) selector button again.
WISYCOM s.r.l. - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) - Italy - MTP30-eng-b04.doc
WISYCOM s.r.l. - Via Spin, 156 - I-36060 Romano d’Ezzelino (VI) - Italy - MTP30-eng-b04.doc
Tel. (Ph.). +39 0424 382605 - Fax +39 0424 382733 - http:// www.wisycom.com
Tel. (Ph.). +39 0424 382605 - Fax +39 0424 382733 - http:// www.wisycom.com
- e-mail: [email protected]
- e-mail: [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

WisyCom MTP30 Quick User Manual

Type
Quick User Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI