Not for
Reproduction
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All Rights Reserved.
8007364
Revision B
Not for
Reproduction
2 simplicitymfg.com
Thank You
Thank you for purchasing this quality-built Brands product.
We are pleased that you have confidence in the Brands
brand. When operated and maintained according to the
manuals, this product will provide many years of dependable
service.
The Operator's Manual contains safety information to make
you aware of the hazards and risks associated with the
unit and how to avoid them. This product was designed to
be used as described in the Operator’s Manual and is not
intended for any other purpose. It is important that you read
and thoroughly understand the instructions in the manual
before attempting to start, operate, or service the product.
Save these original instructions for future reference.
This product requires final assembly, which is described in
the Setup Instructions. Make sure to follow the instructions
completely before use. If you need assistance with assembly,
operation, or maintenance of the product, contact your local
Authorized Service Dealer or visit URL or call Phone (in
USA only).
Identification Tag
Record the model name/number, manufacturer’s
identification numbers, and engine serial numbers in the
space provided for easy access.
Product Model Number:
Product Serial Number:
Engine Model-Type Number:
Engine Code/Serial Number:
Date of Purchase:
Purchase Location:
When contacting the Authorized Dealer for replacement
parts, service, or information you MUST have these
numbers.
The Illustrated Parts List for this machine can be
downloaded from URL . Please provide model and serial
number when ordering replacement parts.
For the location of the identification tag (A), refer to the
following illustration.
1
Vibration Measurement
Uncertainty
Vibration measurement uncertainty - machine vibration
was recorded using methods and procedures outlined in
the appropriate International Standards in effect at the time
of manufacture. The uncertainties due to the measurement
may result in a variance of up to 5% from the published value
shown in the Declaration of Conformity.
Product Warranty
Warranty Statement
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period
specified below, it will repair or replace, free of charge, any
part that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or
replacement under this warranty must be borne by purchaser.
This warranty is effective for and is subject to the time periods
and conditions stated below. For warranty service, find the
nearest Authorized Service Dealer in our dealer locator map
at URL .
The purchaser must contact the Authorized Service Dealer,
and then make the product available to the Authorized
Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties,
including those of merchantability and fitness for a
particular purpose, are limited to the warranty period
listed below, or to the extent permitted by law. Liability
for incidental or consequential damages are excluded
to the extent exclusion is permitted by law. Some states
or countries do not allow limitations on how long an implied
warranty lasts, and some states or countries do not allow
the exclusion or limitation of incidental or consequential
Not for
Reproduction
3
damages, so the above limitation and exclusion may not
apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state
or country to country.**
Warranty Period
Item Consumer
Use
Commercial
Use
Equipment 36 Months 3 Months
Engine* 24 Months 12 Months
Battery (if equipped) 12 Months 12 Months
* Applies to Briggs & Stratton engines only. Warranty
coverage of non-Briggs & Stratton engines is provided by
that engine manufacturer. Emissions-related components are
covered by the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure. For
warranty service, find the nearest Authorized Service Dealer
in our dealer locator map at BRIGGSandSTRATTON.COM,
or by calling 1300 274 447, or by emailing or writing to
[email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia,
2170.
The warranty period begins on the date of purchase by the
first retail or commercial consumer. “Consumer use” means
personal residential household use by a retail consumer.
“Commercial use” means all other uses, including use for
commercial, income producing or rental purposes. Once a
product has experienced commercial use, it shall thereafter
be considered as a commercial use product for purposes of
this warranty.
To ensure prompt and complete warranty coverage, register
your product on-line at www.onlineproductregistration.com.
Save your proof of purchase receipt. If you do not provide
proof of the initial purchase date at the time warranty service
is requested, the manufacturing date of the product will be
used to determine the warranty period. Product registration is
not required to obtain warranty service on Briggs & Stratton
products.
About Your Warranty
Warranty service is available only through Brands Authorized
Service Dealers. This warranty covers only defects in
materials or workmanship. It does not cover damage caused
by improper use or abuse, improper maintenance or repair,
normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of
this product is described in the Operator’s Manual. Using
the product in a way not described in the Operator’s Manual
or using the product after it has been damaged will not be
covered under this warranty. Warranty coverage will also
not be provided if the serial number on the product has been
removed or the product has been altered or modified in any
way, or if the product has evidence of abuse such as impact
damage or water/chemical corrosion damage.
Improper Maintenance or Repair - This product must be
maintained according to the procedures and schedules
provided in the Operator’s Manual, and serviced or repaired
using genuine Briggs & Stratton parts or equivalent. Damage
caused by lack of maintenance or use of non-original parts is
not covered by warranty.
Normal Wear and Tear - Like most mechanical devices,
your unit is subject to wear even when properly maintained.
This warranty does not cover repairs when normal use has
exhausted the life of a part or the equipment. Maintenance
and wear items such as filters, belts, cutting blades, and
brake pads (except engine brake pads) are not covered by
warranty due to wear characteristics alone, unless the cause
is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly,
this product requires fresh fuel that conforms to the criteria
specified in the Operator’s Manual. Engine or equipment
damage caused by stale fuel or the use of unapproved
fuels (such as E15 or E85 ethanol blends) is not covered by
warranty.
Other Exclusions - This warranty excludes damage due
to accident, abuse, modifications, alterations, improper
servicing, freezing or chemical deterioration. Attachments
or accessories that were not originally packaged with the
product are also excluded. There is no warranty coverage on
equipment used for primary power in place of utility power or
on equipment used in life support applications. This warranty
does not include used, reconditioned, second-hand, or
demonstration equipment or engines. This warranty also
excludes failures due to acts of God and other force majeure
events beyond the manufacturer’s control.
80006005EN (Rev A)
Briggs & Stratton Emissions
Warranty
California, U.S. EPA, and Briggs & Stratton Corporation
Emissions Control Warranty - Your Warranty Rights and
Obligations
For Briggs & Stratton Engine Models with "B" or "G"
Trim Designation (Model-Type-Trim Representation
xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs &
Stratton (B&S) are pleased to explain the exhaust emissions
(“emissions”) control system warranty on your 2018-2020
engine. In California, new equipment that use small off-road
engines must be designed, built, and equipped to meet the
State’s stringent anti-smog standards. B&S must warrant
the emissions control system on your engine for the periods
of time listed below provided there has been no abuse,
neglect or improper maintenance of your small off-road
Not for
Reproduction
4 simplicitymfg.com
engine or equipment leading to the failure of the emissions
control system.
Your emissions control system may include parts such as
the carburetor or fuel-injection system, the ignition system,
catalytic converter, fuel tanks, fuel lines (for liquid fuel and
fuel vapors), fuel caps, valves, canisters, filters, clamps and
other associated components. Also included may be hoses,
belts, connectors, and other emission-related assemblies.
Where a warrantable condition exists, B&S will repair your
engine at no cost to you including diagnosis, parts, and
labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is
warranted for two years. If any emissions-related part on
your engine is defective, the part will be repaired or replaced
by B&S.
Owner’s Warranty Responsibilities:
• As the engine owner, you are responsible for the
performance of the required maintenance listed in your
owner’s manual. B&S recommends that you retain all
receipts covering maintenance on your engine, but B&S
cannot deny warranty coverage solely for the lack of
receipts or for your failure to ensure the performance of
all scheduled maintenance.
• As the engine owner, you should however be aware that
B&S may deny you warranty coverage if your engine
or a part has failed due to abuse, neglect, or improper
maintenance or unapproved modifications.
• You are responsible for presenting your engine
to a B&S distribution center or service center as
soon as the problem exists. The warranty repairs
shall be completed in a reasonable amount of time,
not to exceed 30 days. If you have a question
regarding your warranty rights and responsibilities, you
should contact B&S at 1-800-444-7774 (in USA) or
BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty
Provisions
The following are specific provisions relative to your
Emissions Control Warranty Coverage. It is in addition to the
B&S engine warranty for non-regulated engines found in the
Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts
listed below (the emissions control systems parts) to the
extent these parts were present on the B&S engine.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
b. Air Induction System
• Air cleaner
• Intake manifold
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive
valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of
delivery to an ultimate purchaser, or for the time period
listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the
original purchaser and each subsequent purchaser
that the engine is designed, built, and equipped so as
to conform with all applicable regulations adopted by
the Air Resources Board; that it is free from defects in
material and workmanship that could cause the failure
of a warranted part; and that it is identical in allmaterial
respects to the engine described in the manufacturer’s
application for certification. The warranty period begins
on the date the engine or equipment is delivered to an
ultimate purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for
replacement as required maintenance in the
Operator’s Manual supplied, is warranted for the
warranty period stated above. If any such part fails
during the period of warranty coverage, the part will
be repaired or replaced by B&S at no charge to the
owner. Any such part repaired or replaced under
the warranty will be warranted for the remaining
warranty period.
• Any warranted part that is scheduled only for regular
inspection in the Operator’s Manual supplied, is
warranted for the warranty period stated above. Any
such part repaired or replaced under warranty will be
warranted for the remaining warranty period.
• Any warranted part that is scheduled for
replacement as required maintenance in the
Operators’s Manual supplied, is warranted for
the period of time prior to the first scheduled
replacement point for that part. If the part fails prior
to the first scheduled replacement, the part will be
repaired or replaced by B&S at no charge to the
owner. Any such part repaired or replaced under
warranty will be warranted for the remainder of the
period prior to the first scheduled replacement point
for the part.
Not for
Reproduction
5
• Add-on or modified parts that are not exempted by
the Air Resources Board may not be used. The use
of any non-exempted add-on or modified parts by
the owner will be grounds for disallowing a warranty
claim. The manufacturer will not be liable to warrant
failures of warranted parts caused by the use of a
non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine
components caused by the failure of any warranted
emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions
of the B&S engine warranty policy. Warranty coverage
does not apply to failures of emissions parts that are not
original equipment B&S parts or to parts that fail due to
abuse, neglect, or improper maintenance as set forth
in the B&S engine warranty policy. B&S is not liable for
warranty coverage of failures of emissions parts caused
by the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and
Air Index Information On Your Small Off-Road Engine
Emissions Label
Engines that are certified to meet the California Air
Resources Board (CARB) small off-road Emissions Standard
must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this
information available to the consumer on our emissions
labels. The engine emissions label will indicate certification
information.
TheEmissions Durability Perioddescribes the number of
hours of actual running time for which the engine is certified
to be emissions compliant, assuming proper maintenance
in accordance with the Operator’s Manual. The following
categories are used:
Moderate:
Engines at or less than 80 cc displacement are certified to
be emissions compliant for 50 hours of actual engine running
time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 125 hours of actual engine
running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be
emissions compliant for 125 hours of actual engine running
time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 250 hours of actual engine
running time.
Extended:
Engines at or less than 80 cc displacement are certified to be
emissions compliant for 300 hours of actual engine running
time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 500 hours of actual engine
running time.
For example, a typical walk-behind lawn mower is used 20
to 25 hours per year. Therefore, theEmissions Durability
Periodof an engine with anintermediaterating would
equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United
States Environmental Protection Agency (USEPA) Phase 2
or Phase 3 emissions standards. The Emissions Compliance
Period referred to on the Emissions Compliance label
indicates the number of operating hours for which the engine
has been shown to meet Federal emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A
= 300 hours
For engines greater than 80 cc displacement and less
than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category
A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category
A = 1000 hours
80008114EN (Rev G)
Not for
Reproduction
6 simplicitymfg.com
ありがとうございます
この度は高品質の 本ブランド製品をお買い上げいただき、
誠にありがとうございました。私どもの ブランドブランドに
信頼をお寄せいただき、 光栄に存じます。マニュアルに従っ
て、運転 および保守を行っていただければ、購入された製品
は、長年 にわたる信頼性のあるサービスをご提供します。
取扱説明書には、装置をお使いいただく際に伴う危険やリス
クを認識、 回避するための安全に関する情報が 掲載されて
います。本製品は、取扱 説明書に沿った使用を前提に設計さ
れており、他の用途は対象にしておりません。マニュアルを
熟読して 指示内容を十分に理解した上で、本製品の 始動、
運転、整備を行うことが重要です。 今後の参照のため、本取
扱説明書の原本を保管しておいてください。
本製品は最終組立を行う必要があります。詳細はセットアッ
プ手順に 説明されています。使用に当たっては、この手順に
完全に従ってください。製品の組み立て、操作、 メンテナン
スについて支援が必要な場合、お近くの認定サービスディー
ラーにお問合せいただくか、または を ご覧ください URL
または 電話（米国内のみ）へご連絡ください。
識別タグ
ご購入品のモデル名/番号、製造者 識別番号およびエンジン
製造番号を 簡単にアクセスするために提供されたスペース
に表示しておきます。
製品モデル 番号：
製品シリアル 番号：
エンジン・モデル・タイプ 番号：
エンジン・コード/シリアル 番号：
購入日：
購入場所：
交換部品、サービスまたは情報に関して、お近くの認定
ディーラーにお問合せいただくときは、以下の番号をご用意
ください。
この機械用のイラスト付きの部品表は 、 からダウンロード
できます URL . 交換部品をご注文される際は、モデルおよ
びシリアル番号 をご提供ください。
識別タグの位置については (A)、 以下の図をご参照くださ
い。
1
振動測定の不確かさ
振動測定の不確かさ – 機械の振動は 、製造時に有効であった
対応する国際基準に概要が示されていた方法および手順を使
用して記録されました。測定による 不確かさは適合宣言に示
されている 公表値から最大 5% の不一致をもたらす可能性が
あります。
製品の保障
保証声明書
限定保証
ブリッグス アンド ストラットンは、以下に記載した 保証期
間中、材質または仕上がりの欠陥あるいはその両方が認めら
れる一切の 部品について無料にて修理または交換を行なうこ
とを保証します。本保証に基づいて修理または交換を行なう
ための製品配送 費用は、 ご購入者の負担となります。本保
証は以下に述べた 期間内のみ有効であり、以下の条件に従う
ものとします。保証サービスについては、 のディーラー･ロ
ケーターマップで、最寄りの認定サービスディーラーをご確
認下さい URL .
ご購入者はその認定サービスディーラー にご連絡の上、製品
を認定サービスディーラー にて検査および試験を受けられる
状態にしてください。
その他に 明示された保証はありません。市販性、 特定目的
との適合性を含む黙示的な保証は、 以下に表示される保証期
間または法によって許された範囲に限定されます。付随的、
または 結果的に生じる損害に対する責任は、法律で認めら
れている範囲内で除外されます。 州や国によっては、黙示
的 保証期間に制限を設けることが認められない場合や、付随
的、または結果的に生じる損害に対する責任の除外や制限 が
認められない場合があり、お客様に上記の制限や 除外が適用
されない可能性があります。本保証ではお客様に特定の法的
権利を提供しますが、 州や国ごとに 異なる他の権利が与え
られる場合もあります
Not for
Reproduction
7
保証期間
項目 家庭用 業務用
装置 36ヵ月 3ヵ月
エンジン* 24ヵ月 12ヵ月
バッテリー（搭載されている
場合）
12ヵ月 12ヵ月
* ブリッグス アンド ストラットンエンジンにのみ適用。 ブ
リッグス アンド ストラットン製以外のエンジンの保証につ
いては、 エンジンの製造業者によって提供されます。排出ガ
ス関連部品の保証は、Emissions Warranty Statement （排出
ガス保証声明書）によって適用されます。
オーストラリアにおいて - 当社商品は オーストラリア消
費者法に基づいて除外できない保証付で提供されます。
お客様は、 重大な不良が見つかった場合の交換あるいは
払い戻しを受けることができ、その他一切の合理的に予
測可能な損失または 損害に対する補償を受ける権利を有
します。また、 商品が許容品質に到達しておらずその不
良が 重大な不良ではない場合、お客様は商品の修理また
は交換を受ける権利を有します。保証サービスを受ける
には、 BRIGGSandSTRATTON.COMにある当社のディー
ラー位置表示マップにて最寄りの認定サービスディー
ラーを見つけるか、電話（1300 274 447）、 電子メール
（[email protected]）、または郵便
（Briggs & Stratton Australia Pty Ltd, 1 Moorebank Avenue,
NSW, Australia, 2170）にて最寄りの認定サービスディー
ラーにお問合せください。
保証期間は 最初の小売店または商業用消費者による購入日
から開始するものとします。「家庭用」とは、 最終消費者に
よる個人的な家庭における用途を意味します。「業務用」と
は、 業務目的、収益を産んだりレンタルする 目的を含むそ
の他一切の用途を意味します。製品が商業用に一度でも使用
された場合、その後は 本保証の目的において商業的利用の製
品とみなされます。
完全な保証を迅速に受けるためには、
www.onlineproductregistration.com で製品登録を行ってくだ
さい。
購入時のレシートを保管しておいてください。保証サービス
請求時に 最初の購入年月日の証明となるものをお客様から提
示されない 場合、 保証期間の決定に製品の製造年月日が使
用されます。製品の登録は ブリッグス アンド ストラットン
製品の保証サービス を受けるために必須ではありません。
保証について
保証サービスは、ブランドの正規修理店を通してのみご提供
いたします。本保証では、材質または仕上がりの欠陥のみを
対象としています。不適正使用または誤用、不適切な保守ま
たは修理、通常の使用による摩損、あるいは劣化燃料または
非認可燃料の使用によって発生した損傷には対応いたしませ
ん。
不適正な使用および乱用 - 本製品の適切な、意図された用途
は操作マニュアルに記載されています 。操作マニュアルに記
載されていないやり方で製品を使用あるいは製品が損傷を受
けた後に使用した場合、保証は無効となります。製品記載の
シリアル番号が消去されていたり、製品に何らかの変更また
は改変が行なわれている場合、あるいは製品に衝撃損傷また
は水/化学的腐食による損傷など誤用の証拠がある場合、保証
は認められません。
不適正な保守または 修理 - 本製品は操作マニュアルに記載
された手順およびスケジュールにしたがって保守を行い、
ブリッグス アンド ストラットン純正部品あるいは同等品を
使用して整備または修理を行ってください。保守を行なわな
かったり、純正部品以外の部品を使用したことによって生じ
た損傷は、保証の対象外となります。
通常の使用による摩損 - 他の全ての機械類同様、製品は適切
に保守を行なっていても摩損が生じます。本保証では、通
常の使用で部品あるいは製品の耐用期間を消費した場合の修
理を対象としていません。フィルター、ベルト、カッティン
グブレード、ブレーキパッド（エンジンブレーキパッドを除
く）などの保守・消耗部品は、材質または仕上がりの欠陥を
原因としない限り、磨耗特性のみについては保証の対象とは
なりません。
劣化したあるいは未認可の 燃焼 - 本製品が正しく機能するた
めには、操作マニュアルで規定した基準に準拠した新鮮な燃
料を必要とします。劣化燃料または非認可燃料 (E15 または
E85 エタノール混合燃料など) の使用によって発生したエン
ジンまたは装置の損傷は、保証の対象外です。
その他の除外項目 - この保証は、事故、不正使用、変更、改
変、不適切な整備、冷凍、または化学薬品による損傷には適
用されません。製品に同梱されていなかった付属品にも適用
されません。商用電源の代わりの主電源として使用された装
置、または生命維持アプリケーションで使用された装置は保
証の対象外です。中古品、再生品、セカンドハンド品、デモ
用装置またはエンジンは本保証の対象範囲外です。また、製
造業者の責めに帰することができない不可抗力事象による故
障も保証の対象から除外されます。
80006005EN (Rev A)
Not for
Reproduction
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Snapper 2691510-00 User guide
- Type
- User guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Other documents
-
Simplicity RIDER, SIMPLICITY, JA User guide
-
Simplicity RIDER, REGENT, RDLT User guide
-
-
-
-
Simplicity 100802-0118-B8 User manual
-
-
Simplicity 200000 Vanguard User manual
-
-
Simplicity 13D137-0023-F1 User manual