Simplicity RIDER, REGENT, RDLT User guide

Type
User guide
Not for
Reproduction
80027143JA
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All Rights Reserved. Revision B
Not for
Reproduction
Thank You
Thank you for purchasing this quality-built Simplicity® product.
We are pleased that you have confidence in the Simplicity®
brand. When operated and maintained according to the manuals,
this product will provide many years of dependable service.
The Operator's Manual contains safety information to make you
aware of the hazards and risks associated with the unit and
how to avoid them. This product was designed to be used as
described in the Operator’s Manual and is not intended for any
other purpose. It is important that you read and thoroughly
understand the instructions in the manual before attempting to
start, operate, or service the product. Save these original
instructions for future reference.
This product requires final assembly, which is described in the
Setup Instructions. Make sure to follow the instructions
completely before use. If you need assistance with assembly,
operation, or maintenance of the product, contact your local
Authorized Service Dealer or visit simplicitymfg.com or call
1-800-837-6836 (in USA only).
Identification Tag
Record the model name/number, manufacturer’s identification
numbers, and engine serial numbers in the space provided for
easy access.
Product Model Number:
Product Serial Number:
Engine Model-Type Number:
Engine Code/Serial Number:
Date of Purchase:
Purchase Location:
When contacting the Authorized Dealer for replacement parts,
service, or information you MUST have these numbers.
The Illustrated Parts List for this machine can be downloaded
from simplicitymfg.com. Please provide model and serial
number when ordering replacement parts.
For the location of the identification tag (A), refer to the
following illustration.
1
Vibration Measurement
Uncertainty
Vibration measurement uncertainty - machine vibration was
recorded using methods and procedures outlined in the
appropriate International Standards in effect at the time of
manufacture. The uncertainties due to the measurement may
result in a variance of up to 5% from the published value shown
in the Declaration of Conformity.
Product Warranty
Warranty Statement
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period
specified below, it will repair or replace, free of charge, any part
that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or
replacement under this warranty must be borne by purchaser.
This warranty is effective for and is subject to the time periods
and conditions stated below. For warranty service, find the
nearest Authorized Service Dealer in our dealer locator map at
simplicitymfg.com.
The purchaser must contact the Authorized Service Dealer, and
then make the product available to the Authorized Service
Dealer for inspection and testing.
There is no other express warranty. Implied warranties,
including those of merchantability and fitness for a
particular purpose, are limited to the warranty period listed
below, or to the extent permitted by law. Liability for
incidental or consequential damages are excluded to the
extent exclusion is permitted by law. Some states or countries
do not allow limitations on how long an implied warranty lasts,
and some states or countries do not allow the exclusion or
2 simplicitymfg.com
Not for
Reproduction
limitation of incidental or consequential damages, so the above
limitation and exclusion may not apply to you. This warranty
gives you specific legal rights and you may also have other
rights which vary from state to state or country to country.**
Warranty Period
Commercial UseConsumer UseItem
3 Months36 MonthsEquipment
12 Months24 MonthsEngine*
12 Months12 MonthsBattery (if equipped)
* Applies to Briggs & Stratton engines only. Warranty coverage
of non-Briggs & Stratton engines is provided by that engine
manufacturer. Emissions-related components are covered by
the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. For warranty service,
find the nearest Authorized Service Dealer in our dealer locator
map at BRIGGSandSTRATTON.COM, or by calling 1300 274
447, or by emailing or writing to
[email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first
retail or commercial consumer. “Consumer use” means personal
residential household use by a retail consumer. “Commercial
use” means all other uses, including use for commercial, income
producing or rental purposes. Once a product has experienced
commercial use, it shall thereafter be considered as a
commercial use product for purposes of this warranty.
In order to ensure prompt and complete warranty coverage,
register your product at www.onlineproductregistration.com.
Save your proof of purchase receipt. If you do not provide proof
of the initial purchase date at the time warranty service is
requested, the manufacturing date of the product will be used
to determine the warranty period. Product registration is not
required to obtain warranty service on Briggs & Stratton
products.
About Your Warranty
Warranty service is available only through Simplicity®
Authorized Service Dealers. This warranty covers only defects
in materials or workmanship. It does not cover damage caused
by improper use or abuse, improper maintenance or repair,
normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this
product is described in the Operator’s Manual. Using the product
in a way not described in the Operator’s Manual or using the
product after it has been damaged will not be covered under
this warranty. Warranty coverage will also not be provided if the
serial number on the product has been removed or the product
has been altered or modified in any way, or if the product has
evidence of abuse such as impact damage or water/chemical
corrosion damage.
Improper Maintenance or Repair - This product must be
maintained according to the procedures and schedules provided
in the Operator’s Manual, and serviced or repaired using genuine
Briggs & Stratton parts or equivalent. Damage caused by lack
of maintenance or use of non-original parts is not covered by
warranty.
Normal Wear and Tear - Like most mechanical devices, your
unit is subject to wear even when properly maintained. This
warranty does not cover repairs when normal use has exhausted
the life of a part or the equipment. Maintenance and wear items
such as filters, belts, cutting blades, and brake pads (except
engine brake pads) are not covered by warranty due to wear
characteristics alone, unless the cause is due to defects in
material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this
product requires fresh fuel that conforms to the criteria specified
in the Operator’s Manual. Engine or equipment damage caused
by stale fuel or the use of unapproved fuels (such as E15 or
E85 ethanol blends) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to
accident, abuse, modifications, alterations, improper servicing,
freezing or chemical deterioration. Attachments or accessories
that were not originally packaged with the product are also
excluded. There is no warranty coverage on equipment used
for primary power in place of utility power or on equipment used
in life support applications. This warranty does not include used,
reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God
and other force majeure events beyond the manufacturer’s
control.
80006005EN (Rev B)
Emissions Warranty
California, U.S. EPA, and Briggs & Stratton
Corporation Emissions Control Warranty
Statement
For Briggs & Stratton Engine Models with “B” or “G” Trim
Designation
(Model-Type-Trim Representation xxxxxx xxxx Bx or xxxxxx
xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs &
Stratton (B&S) are pleased to explain the emissions control
system warranty on your 2017-2019 engine. In California, new
small off-road engines and large spark ignited engines less than
or equal to 1.0 liter must be designed, built, and equipped to
meet the State’s stringent anti-smog standards. B&S must
warrant the emissions control system on your engine for the
periods of time listed below provided there has been no abuse,
neglect, or improper maintenance of your engine.
Your exhaust emissions control system may include parts such
as the carburetor or fuel injection system, ignition system, and
3
Not for
Reproduction
catalytic converter. Also included may be hoses, belts,
connectors, sensors, and other emissions-related assemblies.
Where a warrantable condition exists, B&S will repair your
engine at no cost to you including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
Small off-road engines and large spark ignited engines less
than or equal to 1.0 liter, are warranted for two years, or for the
time period listed in the respective engine or product warranty
statement, whichever is greater. If any emissions-related part
on your B&S engine is defective, the part will be repaired or
replaced by B&S.
Owner’s Warranty Responsibilities:
As the engine owner, you are responsible for the
performance of the required maintenance listed in your
Operator’s Manual. B&S recommends that you retain all
receipts covering maintenance on your engine, but B&S
cannot deny warranty solely for the lack of receipts or your
failure to ensure the performance of all scheduled
maintenance.
As the engine owner, you should however be aware that
B&S may deny you warranty coverage if your engine or a
part has failed due to abuse, neglect, improper maintenance,
or unapproved modifications.
You are responsible for presenting your engine to a B&S
distribution center, servicing dealer, or other equivalent
entity, as applicable, as soon as a problem exists. The
warranty repairs should be completed in a reasonable
amount of time, not to exceed 30 days. If you have any
questions regarding your warranty rights and responsibilities,
you should contact B&S at 1-800-444-7774 (in USA) or
BRIGGSandSTRATTON.com.
Briggs & Stratton Emissions Control
Warranty Provisions
The following are specific provisions relative to your Emissions
Control Warranty Coverage. It is in addition to the B&S engine
warranty for non-regulated engines found in the Operator’s
Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed
below (the emissions control systems parts) to the extent these
parts were present on the B&S engine.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor or fuel injection system
Oxygen sensor
Electronic control unit
Fuel pump module
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse valve
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and
switches
Connectors and assemblies
2. Length of Coverage
Coverage is for a period of two years from the date of original
purchase, or for the time period listed in the respective engine
or product warranty statement, whichever is greater. B&S
warrants to the original purchaser and each subsequent
purchaser that the engine is designed, built, and equipped so
as to conform with all applicable regulations adopted by the Air
Resources Board; that it is free from defects in material and
workmanship that could cause the failure of a warranted part;
and that it is identical in all material respects to the engine
described in the manufacturer’s application for certification. The
warranty period begins on the date the engine is originally
purchased.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement
as required maintenance in the Operator’s Manual supplied,
is warranted for the warranty period stated above. If any
such part fails during the period of warranty coverage, the
part will be repaired or replaced by B&S at no charge to the
owner. Any such part repaired or replaced under the
warranty will be warranted for the remaining warranty period.
Any warranted part that is scheduled only for regular
inspection in the Operator’s Manual supplied, is warranted
for the warranty period stated above. Any such part repaired
or replaced under warranty will be warranted for the
remaining warranty period.
Any warranted part that is scheduled for replacement as
required maintenance in the Operators’s Manual supplied,
is warranted for the period of time prior to the first scheduled
replacement point for that part. If the part fails prior to the
first scheduled replacement, the part will be repaired or
replaced by B&S at no charge to the owner. Any such part
repaired or replaced under warranty will be warranted for
the remainder of the period prior to the first scheduled
replacement point for the part.
Add-on or modified parts that are not exempted by the Air
Resources Board may not be used. The use of any
non-exempted add-on or modified parts by the owner will
be grounds for disallowing a warranty claim. The
manufacturer will not be liable to warrant failures of
warranted parts caused by the use of a non-exempted
add-on or modified part.
4 simplicitymfg.com
Not for
Reproduction
3. Consequential Coverage
Coverage shall extend to the failure of any engine components
caused by the failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the
B&S engine warranty policy. Warranty coverage does not apply
to failures of emissions parts that are not original equipment
B&S parts or to parts that fail due to abuse, neglect, or improper
maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions
parts caused by the use of add-on or modified parts.
Look For Relevant Emissions Durability
Period and Air Index Information
Engines that are certified to meet the California Air Resources
Board (CARB) small off-road Emissions Standard must display
information regarding the Emissions Durability Period and
the Air Index. Briggs & Stratton makes this information available
to the consumer on our emissions labels. The engine emissions
label will indicate certification information.
The Emissions Durability Period describes the number of
hours of actual running time for which the engine is certified to
be emissions compliant, assuming proper maintenance in
accordance with the Operator’s Manual. The following categories
are used:
Moderate:
Engines at or less than 80 cc displacement are certified to be
emissions compliant for 50 hours of actual engine running time.
Engines greater than 80 cc displacement are certified to be
emissions compliant for 125 hours of actual engine running
time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be
emissions compliant for 125 hours of actual engine running
time. Engines greater than 80 cc displacement are certified to
be emissions compliant for 250 hours of actual engine running
time.
Extended:
Engines at or less than 80 cc displacement are certified to be
emissions compliant for 300 hours of actual engine running
time. Engines greater than 80 cc displacement are certified to
be emissions compliant for 500 hours of actual engine running
time. For example, a typical walk-behind lawn mower is used
20 to 25 hours per year. Therefore, the Emissions Durability
Period of an engine with an intermediate rating would equate
to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States
Environmental Protection Agency (USEPA) Phase 2 or Phase
3 emissions standards. The Emissions Compliance Period
referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown
to meet Federal emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A =
300 hours
For engines greater than 80 cc displacement and less than
225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A
= 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A
= 1000 hours
80008114 (Rev F)
5
Not for
Reproduction
ありがとうございます
この度は高品質の Simplicity®製品をお買い上げいただき、誠
にありがとうございました。私どもの Simplicity®ブランドに
信頼をお寄せいただき、 光栄に存じます。マニュアルに従っ
て、運転 および保守を行っていただければ、購入された製品
は、長年 にわたる信頼性のあるサービスをご提供します。
取扱説明書には、装置をお使いいただく際に伴う危険やリス
クを認識、 回避するための安全に関する情報が 掲載されてい
ます。本製品は、取扱 説明書に沿った使用を前提に設計され
ており、他の用途は対象にしておりません。マニュアルを熟
読して 指示内容を十分に理解した上で、本製品の 始動、運
転、整備を行うことが重要です。 今後の参照のため、本取扱
説明書の原本を保管しておいてください。
本製品は最終組立を行う必要があります。詳細はセットアッ
プ手順に 説明されています。使用に当たっては、この手順に
完全に従ってください。製品の組み立て、操作、 メンテナン
スについて支援が必要な場合、お近くの認定サービスディー
ラーにお問合せいただくか、または を ご覧ください
simplicitymfg.com または 1-800-837-6836(米国内のみ)へ
ご連絡ください。
識別タグ
ご購入品のモデル名/番号、製造者 識別番号およびエンジン
製造番号を 簡単にアクセスするために提供されたスペースに
表示しておきます。
製品モデル 番号:
製品シリアル 番号:
エンジン・モデル・タイプ 番号:
エンジン・コード/シリアル 番号:
購入日:
購入場所:
交換部品、サービスまたは情報に関して、お近くの認定ディー
ラーにお問合せいただくときは、以下の番号をご用意くださ
い。
この機械用のイラスト付きの部品表は 、 からダウンロード
できます simplicitymfg.com. 交換部品をご注文される際は、
モデルおよびシリアル番号 をご提供ください。
識別タグの位置については (A)、 以下の図をご参照ください。
1
振動測定の不確かさ
振動測定の不確かさ – 機械の振動は 、製造時に有効であった
対応する国際基準に概要が示されていた方法および手順を使
用して記録されました。測定による 不確かさは適合宣言に示
されている 公表値から最大 5% の不一致をもたらす可能性が
あります。
製品の保障
保証声明書
限定保証
ブリッグスアンドストラットンは、以下に記載した保証期間
中、材質または仕上がりの欠陥あるいはその両方が認められ
る一切の 部品について無料にて修理または交換を行なうこと
を保証します。本保証に基づいて修理または交換を行なうた
めの製品配送 費用は、 ご購入者の負担となります。本保証は
以下に述べた 期間内のみ有効であり、以下の条件に従うもの
とします。保証サービスについては、 のディーラー・ロケー
ターマップで、最寄りの認定サービスディーラーをご確認下
さい simplicitymfg.com.
ご購入者はその認定サービスディーラー にご連絡の上、製品
を認定サービスディーラー にて検査および試験を受けられる
状態にしてください。
その他に 明示された保証はありません。市販性、 特定目的と
の適合性を含む黙示的な保証は、 以下に表示される保証期間
または法によって許された範囲に限定されます。付随的、ま
たは 結果的に生じる損害に対する責任は、法律で認められて
いる範囲内で除外されます。 州や国によっては、黙示的保証
期間に制限を設けることが認められない場合や、付随的、ま
たは結果的に生じる損害に対する責任の除外や制限 が認めら
れない場合があり、お客様に上記の制限や 除外が適用されな
い可能性があります。本保証ではお客様に特定の法的権利を
6 simplicitymfg.com
Not for
Reproduction
提供しますが、 州や国ごとに 異なる他の権利が与えられる場
合もあります
保証期間
業務用家庭用項目
3ヵ月36ヵ月装置
12ヵ月24ヵ月エンジン*
12ヵ月12ヵ月バッテリー(搭載されている場
合)
* ブリッグス アンド ストラットンエンジンにのみ適用。 ブ
リッグス アンド ストラットン製以外のエンジンの保証につい
ては、 エンジンの製造業者によって提供されます。排出ガス
関連部品の保証は、Emissions Warranty Statement (排出ガ
ス保証声明書)によって適用されます。
オーストラリアにおいて - 当社商品は オーストラリア消費者
法に基づいて除外できない保証付で提供されます。お客様は、
重大な不良が見つかった場合の交換あるいは払い戻しを受け
ることができ、その他一切の合理的に予測可能な損失または
損害に対する補償を受ける権利を有します。また、 商品が許
容品質に到達しておらずその不良が重大な不良ではない場合、
お客様は商品の修理または交換を受ける権利を有します。保
証サービスを受けるには、 BRIGGSandSTRATTON.COMにあ
る当社のディーラー位置表示マップにて最寄りの認定サービ
スディーラーを見つけるか、電話(1300 274 447)、 電子メー
ル([email protected])、または郵便
(Briggs & Stratton Australia Pty Ltd, 1 Moorebank Avenue,
NSW, Australia, 2170)にて最寄りの認定サービスディーラー
にお問合せください。
保証期間は 最初の小売店または商業用消費者による購入日か
ら開始するものとします。「家庭用」とは、 最終消費者によ
る個人的な家庭における用途を意味します。「業務用」とは、
業務目的、収益を産んだりレンタルする 目的を含むその他一
切の用途を意味します。製品が商業用に一度でも使用された
場合、その後は 本保証の目的において商業的利用の製品とみ
なされます。
完全な保証を迅速に受けるためには、
www.onlineproductregistration.com で製品登録を行ってくださ
い。
購入時のレシートを保管しておいてください。保証サービス
請求時に 最初の購入年月日の証明となるものをお客様から提
示されない 場合、 保証期間の決定に製品の製造年月日が使用
されます。製品の登録はブリッグスアンドストラットン製品
の保証サービス を受けるために必須ではありません。
保証について
保証サービスは、 Simplicity® 修理店を通してのみご提供いた
します。本保証では、材質または仕上がりの欠陥のみを対象
としています。不適正使用または誤用、不適切な保守または
修理、通常の使用による摩損、 あるいは劣化燃料または非認
可燃料の使用によって発生した損傷には対応 いたしません。
不適正な使用および乱用 - 本製品の適切な、意図された用途は
操作 マニュアルに記載されています。操作マニュアルに記載
されていないやり方で製品を使用あるいは 製品が損傷を受け
た後に使用した場合、 保証は無効となります。製品記載の シ
リアル番号が消去されていたり、製品に何らかの 変更または
改変が行なわれている場合、あるいは 製品に衝撃損傷または
水/化学的腐食による損傷など誤用の証拠がある場合、保証
は認められません。
不適正な保守または 修理 - 本製品は操作マニュアルに記載さ
れた手順およびスケジュールにしたがって保守を行い、ブリッ
グス アンド ストラットン純正部品あるいは同等品を使用して
整備または修理を行ってください。保守を行なわなかったり
、純正部品以外の部品を使用したことによって生じた損傷は、
保証の対象外となります。
通常の使用による摩損 - 他の全ての機械類同様、製品は 適切
に保守を行なっていても摩損が生じます。本保証では、通常
の使用で部品あるいは製品の耐用期間を 消費した場合の修理
を対象としていません。フィルター、ベルト、カッティング
ブレード、ブレーキパッド(エンジンブレーキパッドを除く)
などの 保守・消耗部品は、材質または仕上がりの欠陥を原因
としない限り 、磨耗特性のみについては保証の対象とはなり
ません。
劣化したあるいは未認可の 燃焼 - 本製品が正しく機能するた
めには 、操作マニュアルで規定した基準に準拠した新鮮な燃
料を必要とします。劣化燃料または 非認可燃料 ( E15 または
E85 エタノール混合燃料など) の使用によって発生したエンジ
ンまたは装置の損傷は、保証の対象外です。
その他の除外項目 - この保証は、事故、不正使用、変更、 改
変、不適切な整備、冷凍、または化学薬品による損傷には適
用されません。 製品に同梱されていなかったアタッチメント
やアクセサリも 除外対象となります。商用電源の代わりの主
電源として使用された装置、または生命維持 アプリケーショ
ンで使用された装置は保証の対象外です。中古品、再生品、
セカンドハンド品、 デモ用装置またはエンジンは本保証の対
象範囲外です。また、製造業者の 責めに帰することができな
い 不可抗力事象による故障も保証の対象から除外されます。
80006005EN (Rev B)
7
Not for
Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Simplicity RIDER, REGENT, RDLT User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI