Raven AccuBoom Installation guide

Raven
Brand
Raven
Model
AccuBoom
Type
Installation guide

Raven AccuBoom

Raven AccuBoom is a system designed to provide worry-free automatic turn on and turn off of your booms with respect to the as-applied coverage map. It helps you avoid skips and overlaps in coverage, reducing chemical and fertilizer waste. The system can be easily installed by following the instructions in the Installation Manual.

AccuBoom is compatible with Envizio Plus/Pro or Viper/Viper Pro consoles. It requires a CAN AccuBoom Node, a Machine Specific Console Cable, and CAN Tee Cables. Once installed, the system uses LED lights to provide diagnostic information about Logic Power, Micro 1 Hz, CAN Rx, CAN Tx, and High Current Power.

Raven AccuBoom

Raven AccuBoom is a system designed to provide worry-free automatic turn on and turn off of your booms with respect to the as-applied coverage map. It helps you avoid skips and overlaps in coverage, reducing chemical and fertilizer waste. The system can be easily installed by following the instructions in the Installation Manual.

AccuBoom is compatible with Envizio Plus/Pro or Viper/Viper Pro consoles. It requires a CAN AccuBoom Node, a Machine Specific Console Cable, and CAN Tee Cables. Once installed, the system uses LED lights to provide diagnostic information about Logic Power, Micro 1 Hz, CAN Rx, CAN Tx, and High Current Power.

Case IH FLX 10 Series
Installation Manual
P/N 016-1001-049 Rev A 09/15
Copyright 2007, 2015
Manual # 016-1001-049
1
C H A P T E R
1
INTRODUCTION
Congratulations on your purchase of the Raven AccuBoom system! This system
is designed to provide worry-free turn on and turn off of your booms with respect
to the as-applied coverage map. The following instructions are designed to
assist you in the proper installation of the AccuBoom system. See the Installation
and Operation Manual of your particular console for instructions on setting up the
software and using the AccuBoom system.
Basic Kit
Contents
AccuBoom CAN Node
Machine Specific Console Cable (115-1001-018)
CAN Tee Cable: 12’ long (115-0171-362)
CAN Tee Cable: 6’ long (115-0171-753) (2)
Install Manual
Important! All boom switches must be in the ON
position while AccuBoom control is in operation!
Important! Boom configuration must be set up in
Envizio Plus/Pro or Viper/Viper Pro so that
Boom 1 = Left Fence Row
Boom 2 = Boom 1
Boom 3 = Boom 2, etc.
Boom 1 (left fence row) normally gets a 0” or 1” value and
uncheck Boom 1 from Accuboom operation.
CaseIH FLX 10 Series AccuBoom Installation Manual
2
Notes:
Manual # 016-1001-049
3
C H A P T E R
2
INSTALLATION
Use the following procedure to properly install the CAN AccuBoom
system.
1. Locate Bulthead 5 Connector beneath cab.
2. Disconnect Bulkhead 5 Connector and tee in Accuboom
harness.
3. Locate power and ground studs near bulkhead connectors.
Connect Red/White wires with ring terminals on Accuboom
harness to power/ground studs.
Bulkhead panel and power/
ground studs beneath cab
CaseIH FLX 10 Series AccuBoom Installation Manual
4
4. Locate Acc Power connector beneath cab. Remove cap and
connect Accuboom Harness (switched power).
5. Drill 2 holes in enclosure lid underneath catwalk on the right side
of the cab to mount the CAN Node.
Mount CAN Node to enclosure lid.
6. Connect the Accuboom harness to the CAN Node. Connect the
12’ CAN Tee (115-0171-362) to the Accuboom harness and
connect the terminator (063-0172-369) to the CAN Tee. Route
the CAN Tee harness through the floorboard into the cab.
Connect harness to CAN Node
Manual # 016-1001-049
5
7. Locate the A-Post panel in the cab. Remove the 4 screws and
locate the CAN Bus Terminator behind the plate.
8. Remove the Terminator and route the CAN Tee harness
(115-0171-753) to the CAN Connector and connect. Replace the
A-Post panel.
9. Connect the CAN Tee cable (115-0171-753) to the CAN Tee
cable routed into the cab (115-0171-362) from the CAN Node.
Connect the CAN Terminator from the A-Post to the CAN Tee
cable (115-0171-753).
NOTE: If you are using an Envizio Plus, you will need to use the
additional CAN Tee cable (115-0171-753) and connect the Envizio
Plus to the CAN Bus. Connect the CAN Terminator from the
A-Post to the CAN Tee cable (115-0171-753).
10. Installation is now complete.
CaseIH FLX 10 Series AccuBoom Installation Manual
6
Manual # 016-1001-049
7
C H A P T E R
3
DIAGNOSTICS
The CAN AccuBoom Node P/N 063-0172-316 has additional features to allow the
user to diagnose the AccuBoom system. The CAN AccuBoom node has a
plastic window in the case that allows the user to view green diagnostic lights.
The picture below shows the positioning and function of each of the LED lights.
Logic Power
Micro 1 Hz
CAN Rx
CAN Tx
High Current
Power (HC)
Logic Powr: Lit when 12VDC logic power is available at the node.
Micro 1 Hz: Flashes at 1 Hz interval when processor is active.
CAN Rx: Flashes when CAN messages are being received.
CAN Tx: Flashes when CAN messages are being transmitted.
High Current Power: Lit when High Current Power is applied to teh node.
CaseIH FLX 10 Series AccuBoom Installation Manual
8
Notes:
RAVEN INDUSTRIES
LIMITED WARRANTY
WHAT IS COVERED?
This warranty covers all defects in workmanship or materials in your Raven
Flow Control Product under normal use, maintenance, and service.
HOW LONG IS THE COVERAGE PERIOD?
This warranty coverage runs for 12 months from the purchase date of your
Raven Flow Control Product. This warranty coverage applies only to the
original owner and is not transferrable.
HOW CAN YOU GET SERVICE?
Bring the defective part, and proof of date of purchase, to your local dealer. If
your dealer agrees with the warranty claim, he will send the part, and proof
of purchase to his distributor or to Raven for final approval.
WHAT WILL RAVEN INDUSTRIES DO?
When our inspection proves the warranty claim, we will, at our option, repair
or replace the defective part and pay for return freight.
WHAT DOES THIS WARRANTY NOT COVER?
Raven Industries will not assume any expense or liability for repairs made
outside our plant without written consent. We are not responsible for damage
to any associated equipment or product and will not be liable for loss of profit
or other special damages. The obligation of this warranty is in lieu of all
other warranties, expressed or implied, and no person is authorized to
assume for us any liability. Damages caused by normal wear and tear, mis-
use, abuse, neglect, accident, or improper installation and maintenance are
not covered by this warranty.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Raven AccuBoom Installation guide

Raven
Brand
Raven
Model
AccuBoom
Type
Installation guide

Raven AccuBoom

Raven AccuBoom is a system designed to provide worry-free automatic turn on and turn off of your booms with respect to the as-applied coverage map. It helps you avoid skips and overlaps in coverage, reducing chemical and fertilizer waste. The system can be easily installed by following the instructions in the Installation Manual.

AccuBoom is compatible with Envizio Plus/Pro or Viper/Viper Pro consoles. It requires a CAN AccuBoom Node, a Machine Specific Console Cable, and CAN Tee Cables. Once installed, the system uses LED lights to provide diagnostic information about Logic Power, Micro 1 Hz, CAN Rx, CAN Tx, and High Current Power.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents