Hobart GF-60 S Installation & Operation Manual
- Type
- Installation & Operation Manual
This manual is also suitable for
Hobart GF-60 S is a glasswasher designed to wash dishes such as glasses, cups, cutlery etc. The machine is easy to install and features a built-in softener to prevent limescale build-up. It has three wash programs to choose from, depending on the level of cleaning required. The machine also features a detergent and rinse agent dispenser, which can be adjusted to suit the specific needs of your dishes. With its compact size and efficient operation, the Hobart GF-60 S is the perfect choice for any commercial kitchen.
Hobart GF-60 S is a glasswasher designed to wash dishes such as glasses, cups, cutlery etc. The machine is easy to install and features a built-in softener to prevent limescale build-up. It has three wash programs to choose from, depending on the level of cleaning required. The machine also features a detergent and rinse agent dispenser, which can be adjusted to suit the specific needs of your dishes. With its compact size and efficient operation, the Hobart GF-60 S is the perfect choice for any commercial kitchen.
INSTALLATION OPERATION
Glasswasher
GF-60 and GF-60 S
VERSION 02/08/01
2
Installation and Operation Instructions
for Model GF-60 and
GF-60 S (with built-in softener)
Content Page
1 Installation ............................................................................................. 3
2 Connections .......................................................................................... 4
3 Controls................................................................................................. 5
4 First run ................................................................................................. 6
5 Dispensers ............................................................................................ 7
6 Softener (GF-60 S only) ....................................................................... 8
7 Operation ............................................................................................ 10
8 Cleaning .............................................................................................. 11
9 Frost prevention .................................................................................. 12
10 Manitenance ....................................................................................... 12
11 Trouble shooting guide ......................................................................... 13
Machine noise level is
≤
70 dB (A).
Important Notes
● Use in Accordance with Regulations
This Machine is exclusively to be used to wash dishes such as glasses,
cups, cutlery etc.
Do not use for electrically heated cooking and heat conservation
appliances.
● Safety
Never hose down the machine.
The "Attention" symbol is shown beside instructions that are essential
for the safe operation of the machine. Please read these passages
very thoroughly.
● Liability
Installations and repairs which are not carried out by authorized
technicians or the use of other than original spare parts, and any
technical alterations to the machine, may affect the warranty set
out in the standard conditions of sale.
3
1 Installation
1.1 Transport to installation location
– If possible in its packing and on skid.
– Use a wheel barrow or slide on piece of carpet.
– Avoid damage to floor and doors.
1.2 Remove packing
– Cut steel bands.
– Remove carton.
– Remove wooden skid.
– Remove inside packing material and accessories.
– Check for are any shipping damage.
In case of doubt do not use the machine until it has been
checked by an authorized specialist.
1.3 Locating
– Wall clearance is not required.
– Level machine by turning the feet.
– Distribute machine weight equally onto all feet.
4
2 Connections
2.1 Electrical connection
Must be carried out by an authorized technician
according to the local and national codes.
– Set main switch at site.
– Check machine specifications to make sure they correspond to
those of the site supply and the wiring diagram.
– Check site fuse rating.
According to EN 60 335 the appliance must be connected to a
equipotential conductor. The connecting screw is located beside
the cable inlet.
2.2 Water connection
– Connect if possible to soft and warm water (4 °Clark, max. 50°C).
– Line flow pressure 2 – 4 bar.
If line flow pressure is below 2 bar: provide rinse booster
pump at site.
If line flow pressure is above 4 bar: provide pressure reducer.
– Connect flexible supply hose with union nut
3
/
4
" to site
connection.
– Site pipework min. 19 mm ID.
– Provide shut-off valve.
– The machine is equiped with a backflow preventer
(GF-60 S with a Type A airgap).
The machine must be operated with water of
drinking quality.
For water with an extremely high mineral content,
water treatment is recommended.
2.3 Drain connection
– Connect to trapped drain line.
– Connection between machine and site drain must not exceed
max. height of 1 metre.
– Do not kink drain hose.
– When connected to floor drain the drain hose must be at least
400 mm above the floor to prevent the tank from draining empty.
Should be fixed with the supplied hose clamp if necessary.
min. 400 mm
max. 1 m
5
1. Start button
2. Detergent dispenser pilot light (illuminates when the container is empty)
3. Programme pilot light
4. Pilot light Regeneration (GF-60 S only)
5. Pilot light Machine ON
SELECTOR SWITCH:
6. 60 sec. short wash programme
7. 120 sec. normal wash programme
8. Machine OFF
9. Tank drain
10. Regeneration (GF-60 S only)
To reach hygienic rinse temperatures even with cold water connection or reduced heating power,
the actual cycle times extend accordingly.
3 Controls
1 2 3 4 5
7
8 9
6 10
6
4 First Run
Check level of detergent and rinse agent containers.
Make sure that the strainer is in correct position.
(If it is in a wrong position or missing, the machine cannot be
started.)
4.1 Filling the machine
– Open shut-off valve.
– Switch on main switch.
– Close the door.
– Set selector switch to Wash programme (I or II).
Pilot light Machine ON illuminates.
– The machine will automatically fill-up and at the same time the
rinse booster heater will be switched on.
Attention: Do not push the Start button !
– For single-phase machine allow 15 minutes for the wash water
to heat up before commencing washing.
This time is reduced for three-phase machines.
– After installation: switch off machine.
– Loosen the connection indicated (see fig.) to release air from
the pipe work.
– Tighten the connection.
4.2 Test cycle
– Push Start button until the pilot light programme illuminates.
The wash cycle starts.
A complete wash cycle consists of: wash, drain and rinse.
– When pilot light switches off, wash cycle is finished.
4.3 Check
– While the cycle is running open the door slowly, and check
if upper and lower wash and rinse arms rotate smoothly.
– Check and eliminate any leakages from the supply and drain
pipe-work.
7
5 Dispensers
5.1 Filling the containers
Rinse agent
– Open the flap of the lower front panel and fill the receptacle by
using the supplied funnel.
Detergent
Do not use any acidic detergent products with the built-in
detergent pump.
– Put suction hose into detergent container.
Note: Run machine empty for one wash cycle until suction
hose is filled.
– To avoid the dry running of the detergent pump, the suction
hose is equipped with a level switch.
Use only commercial detergent and rinse agent.
Please pay attention to the manufacturers safety rules
and instructions.
5.2 Concentration adjustment
To be done by an authorized technician in accordance with the
detergent and rinse agent producer’s instructions.
Rinse agent
– Switch off machine.
– Set main switch to "0".
– Remove lower front panel carefully.
– Turn the adjusting screw (behind the panel).
Turn to left: increase dosage / turn to right: decrease dosage.
– The dispenser is factory adjusted to max. position.
Detergent
– Switch off machine.
– Set main switch to "0".
– Open the upper front panel (A).
– To adjust the detergent concentration turn the potentiometer (B)
of the electronic board.
Turn to right: increase dosage / turn to left: decrease dosage.
– Close panels after adjustment.
– The dispenser is factory adjusted to medium position.
Ask your rinse agent and detergent supplier concerning an
optimum adjustment for quantity.
+
–
A
B
03
12
"B"
8
6 Softener (GF-60 S only)
6.1 Adjustment
The built-in cycle counter compares the number of performed
wash cycles with the set degree of water hardness.
– To know water hardness level ask local water authority.
– The softener is factory adjusted to 25° clark.
To modify the settings:
– Switch off machine.
– Set main switch to "0".
– Open the upper front panel (A).
The water hardness and the number of wash cycles respectively
can be adjusted by means of pushing-in a number of notches at
the cycle counter (C).
(e.g. factory adjusted water hardness is 25° clark, that means
17 pushed-in notches resp. 34 wash cycles)
Number of wash cycles between two regenerations:
°clark cams
wash
°clark cams
wash
cycles cycles
2.5 52 104 20 22 44
442 842120 40
5 38 76 22.5 19 38
636 722418 36
7.5 35 70 25 17 34
933 662615 30
10 32 64 27.5 14 28
11 30 60 29 12 24
12.5 29 58 30/31 11 22
14 28 56 32.5/34 10 20
15 27 54 35/37.5 9 18
16 26 52 39/42.5 8 16
17.5 24 48 44/46 7 14
19 23 46 47.5/50 6 12
After adjustment rotate the cam-shaft clockwise until the micro-
switch locks into place.
A
C
9
6.2 Regeneration
When the machine is delivered, the softener is already
regenerated.
– When regeneration pilot light illuminates (indicating that salt is
required), set programme switch to drain position.
– Push the start button until the programme pilot light illuminates.
– When the pilot light switches off, open the door.
– Unscrew the softener lid.
– Hold the supplied dispenser funnel at its handle and fill up with
salt to mark "B" (250 g).
Use Granular salt only. Salt tablets or powdered salt are not
recommended.
– Set the funnel on the opening of the salt receptacle and push
down handle until the funnel is empty.
– Take out funnel.
Clean seal and rim of softener lid and border carefully
before closing the lid.
– Close lid and tighten.
Important: only fill with salt just before starting the
regeneration programme.
– Close the door.
– Set the programme switch to regeneration position.
Push start button until the programme pilot light illuminates.
– While the cycle is running, the pilot light regeneration switches off.
Attention:
Do not open the door during regeneration.
– After approx. 20 minutes the programme pilot light switches off,
the regeneration is finished.
– Machine is ready to wash.
A
B
10
min.
max.
7 Operation
7.1 Preparation (daily)
First remove lemon peels, tooth- Spray off dishes.
picks, olive pips etc. Then put
glasses and cups into racks with
the opening facing downwards.
7.2 Racking
Check correct position of wash and Check level of detergent and rinse Close door, set programme switch
rinse arms and the strainer. The agent containers. to wash programme.
machine can only be started if the After approx. 30 sec. (when tank
strainer is in correct position. is filled) push start button.
Switch on main switch and open
shut-off valve.
11
Set programme switch to drain When programme pilot light Set main switch to "0" and close
position. Close the door and push switches off, open door, take out shut-off valve.
start button until programme pilot and clean strainer. Clean interior of Put strainer back into place.
light illuminates. machine. Switch OFF machine. Leave the door open for ventilation.
If required
7.3 Washing
Put rack into the machine and Select the wash programme and When the programme pilot light
close door. push start button. Programme pilot switches off, open door and take
light illuminates, cycle is running. out rack.
Give glasses sufficient time to dry.
IMPORTANT
Since the two wash arms are
different, they cannot be installed
in the wrong position.
If, while fitting an arm, any
resistance is experienced, never
force it in, exchange it with the
other arm.
Dismantle the rinse arms by Put the parts back into place in
un-screwing the thumb-screws. reverse order.
Remove wash arms from the shaft.
Check and clean all nozzles.
8 Cleaning (daily)
12
9 Frost prevention
In case of frost or longer operation pauses (e.g. for seasonal
operations) the machine must be completely drained.
This should be carried out by HOBART after sales service.
Please contact your local HOBART Office.
Reset for operation according to chapter 4.
10 Maintenance
For trouble free operation we recommend you enter into a service
contract with your local HOBART Service Office.
13
11 Trouble shooting guide
TYPE OF FAILURE POSSIBLE CAUSE REMEDY
Poor wash result
Glasses are not clean. Wash arms stiff (you should be able Take out wash arms and clean them thoroughly.
to turn them easily by hand). Check water outlet from machine to wash arms is
clear.
Wash arm nozzles are clogged Take out wash arm and rinse it thoroughly until
(visual check). soil is removed. Replace correctly.
Rinse nozzles are clogged (generally Remove rinse arms and decalcify them in
through lime deposit). separate container.
Please check external water treatment device.
Detergent concentration is too low or Check setting of detergent concentration.
too high.
Strainer soiled. Take out strainer, empty and clean it.
Wrong programme selected for heavily Select programme with longer wash cycle.
soiled dishes.
Glasses do not dry Rinse aid concentration too low. Increase settings (see operating instructions).
properly.
Dishes still greasy. 1. Detergent concentration too low: increase.
2. Check if detergent is appropriate if not
choose a stronger one.
3. Drain soiled water and refill machine.
Check pre-scrapping procedure.
Rack is not suitable for type of dishes Use appropriate racks to create a sloping position
(sloping). which allows water to drain away from cavities.
Dishes stay too long in the machine Take out dishes as soon as cycle is completed
at the end of programme. to enable them to dry.
Stripes and stains on Rinse aid concentration too high. Reduce settings (see operating instructions).
glasses.
Hard water or high mineral content. Check water quality.
Obtain details from local water authority.
Recommended values:
Ideal degree of hardness is 4˚ Clark.
Ideal conductivity value for glasses is max.
150 µs/cm and for dishes max. 400 µs/cm.
Rack is not suitable for type of dishes Use appropriate racks to create a sloping position
(sloping). which allows water to drain away from cavities.
Insufficient rinse aid concentration Increase settings (see instructions).
causes stains.
Machine with softener:
use of wrong type of salt (too coarse). Use only fine salt (grain size 1 – 3 mm).
Machine with softener:
salt container is full although softening Only fill in salt just before regeneration
does not take place. programme will be activated.
14
Trouble shooting guide
TYPE OF FAILURE POSSIBLE CAUSE REMEDY
Softener malfunctions
(only concerning GF-60 S)
Lime deposit in the Regeneration call was "ignored" i.e. Run regeneration program 2-3 times (refill salt
machine. the machine went on washing when container every time). Decalcify machine.
regeneration was needed.
Strainer in water supply pipe clogged Clean it. If necessary replace it with heavy duty
(in site tap). filter (available as accessory).
Salt container not tight. During filling, salt was spilt over the Open softener lid, remove salt with a cloth and
edge and not removed. close lid tightly.
Other malfunctions
Glasses are totally or Surface of glasses is rough and porous; This is not caused by a malfunction on the
partially cloudy. this is called glass corrosion. machine. Replace with new glasses.
Glass breakages. Use of inappropriate dish or glass racks. Use appropriate racks.
Machine suddenly stops Machine is connected to a "maximum Connect machine separately (call electrician).
during wash programme. power supply unit", or machine is inter-
locked with another power using unit.
Blown site fuse. Check site fuses.
15
As continued product improvement is a policy of HOBART, specifications are subject to change without notice.
Printed in Germany AG-20636-C-08-01-PC
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Hobart GF-60 S Installation & Operation Manual
- Type
- Installation & Operation Manual
- This manual is also suitable for
Hobart GF-60 S is a glasswasher designed to wash dishes such as glasses, cups, cutlery etc. The machine is easy to install and features a built-in softener to prevent limescale build-up. It has three wash programs to choose from, depending on the level of cleaning required. The machine also features a detergent and rinse agent dispenser, which can be adjusted to suit the specific needs of your dishes. With its compact size and efficient operation, the Hobart GF-60 S is the perfect choice for any commercial kitchen.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hobart AUXXT Series Installation & Operation Manual
-
-
Hobart FP Installation And Operation Instructions Manual
-
-
-
-
-
-
-