Tyan YR190-B8238 Service Engineer's Manual

1

http://www.tyan.com

YR190-B8238

Service Engineer’s Manual

2

http://www.tyan.com

3

http://www.tyan.com

PREFACE

Copyright

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced

without written consent of manufacturer.

TYAN

®

is a registered trademark of MiTAC International Corporation.

Version 1.0

Disclaimer

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to

printing. MiTAC assumes no liability whatsoever, and disclaims any

express or implied warranty, relating to sale and/or use of TYAN

®

products

including liability or warranties relating to fitness for a particular purpose or

merchantability. MiTAC retains the right to make changes to produce

descriptions and/or specifications at any time, without notice. In no event

will MiTAC be held liable for any direct or indirect, incidental or

consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Trademark Recognition

All registered and unregistered trademarks and company names

contained in this manual are property of their respective owners including,

but not limited to the following.

TYAN

®

is a trademark of MiTAC International Corporation.

Intel

®

is a trademark of Intel

®

Corporation.

AMI

®

, AMIBIOS

®

and combinations thereof are trademarks of AMI

Technologies.

Microsoft

®

, Windows

®

are trademarks of Microsoft Corporation.

IBM

®

, PC

®

, AT

®

and PS/2

®

are trademarks of IBM Corporation.

Winbond

®

is a trademark of Winbond Electronics Corporation.

4

http://www.tyan.com

Federal Communication Commission (FCC)

Notice for the USA

Compliance Information Statement (Declaration of

Conformity Procedure) DoC FCC Part 15: This

device complies with part 15 of the FCC Rules

Operation is subject to the following conditions:

1) This device may not cause harmful interference;

2) This device must accept any interference received including

interference that may cause undesired operation. If this equipment

does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the

user is encouraged to try one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the receiver.

– Plug the equipment into an outlet on a circuit different from that of

the receiver.

Consult the dealer on an experienced radio/television technician for

help.

Notice for Canada

This apparatus complies with the Class A limits for radio interference as

specified in the Canadian Department of Communications Radio

Interference Regulations. (Cet appareil est conforme aux norms de

Classe A d’interference radio tel que specifie par le Ministere Canadien

des Communications dans les reglements d’ineteference radio.)

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 89/336/EEC, 92/31/EEC (EMC).

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. There will be danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery according

to manufacturer instructions and in accordance with your local

regulations.

5

http://www.tyan.com

About this Manual

This manual provides you with instructions on installing your TYAN

YR190-B8238. This Manual is intended for experienced users and

integrators with hardware knowledge of personal computers.

This manual consists of the following parts:

Chapter1:

Provides an introduction to the TYAN YR190-B8238

barebones, standard parts list, describes the external

components, gives a table of key components, and

provides block diagram of the system.

Chapter2:

Covers procedures on installing the CPU, memory

modules and hard drives.

Chapter3:

Covers removal and replacement procedures for

pre-installed components.

Appendix:

List the cable connection and FRU part tables for

reference of system setup, and technical support

in

case a problem arises with your system.

6

http://www.tyan.com

SAFETY INFORMATION

Before installing and using TYAN YR190-B8238, take note of the

following precautions:

·Read all instructions carefully.

·Do not place the unit on an unstable surface, cart, or stand.

·Do not block the slots and opening on the unit, which are provided for

ventilation.

·Only use the power source indicated on the marking label. If you are not sure,

contact the power company.

·The unit uses a three-wire ground cable, which is equipped with a third pin to

ground the unit and prevent electric shock. Do not defeat the purpose of this

pin. If you outlet does not support this kind of plug, contact your electrician to

replace your obsolete outlet.

·Do not place anything on the power cord. Place the power cord where it will not

be in the way of foot traffic.

·Follow all warnings and cautions in this manual and on the unit case.

·Do not push objects in the ventilation slots as they may touch high voltage

components and result in shock and damage to the components.

· When replacing parts, ensure that you use parts specified by the

manufacturer.

·When service or repairs have been done, perform routine safety checks

to verify that the system is operating correctly.

·Avoid using the system near water, in direct sunlight, or near a heating device.

·Cover the unit when not in use.

·Please separate HDD during shipment, and install HDD after system set

up completely and prior to power up.

7

http://www.tyan.com

Table of Contents

Chapter 1: Overview.........................................................................9

1.1 About the TYAN YR190-B8238 ................................................ 9

1.2 Features.................................................................................. 10

1.3 Product Model......................................................................... 14

1.4 Standard Parts List ................................................................. 15

1.4.1 Box Contents Per Node................................................... 15

1.4.2 Accessories ..................................................................... 16

1.5 About the Product................................................................... 18

1.5.1 System Front View (Per Node)........................................ 18

1.5.2 System Rear View (Per Node) ..................................... 20

1.5.3 Internal View (Per Node) ................................................. 21

Chapter 2: Setting Up.....................................................................23

2.0.1 Before you Begin ............................................................. 23

2.0.2 Work Area........................................................................ 23

2.0.3 Tools ................................................................................ 23

2.0.4 Precautions...................................................................... 24

2.1 Installing Motherboard Components....................................... 25

2.1.1 Installing Hard Drives....................................................... 25

2.1.2 Installing the CPU and Heatsink...................................... 28

2.1.3 Installing the Memory....................................................... 31

2.2 Rack Mounting........................................................................ 36

2.2.1 Installing the Server in a Rack......................................... 36

2.2.2 Installing the inner Rails to the Chassis........................... 37

2.2.3 Installing the Outer Rails to the Rack .............................. 38

2.2.4 Rack mounting the Server ............................................... 39

Chapter 3: Replacing Pre-Installed Components ........................ 43

3.1 Introduction ............................................................................. 43

3.2 Disassembly Flowchart........................................................... 43

3.3 Replacing Motherboard Components..................................... 45

3.3.1 Replacing Expansion Card .............................................. 45

3.3.2 Disconnecting All Motherboard Cables ........................... 47

3.3.3 Removing the Motherboard ............................................. 48

3.4 Replacing the Power Distribution Board ............................... 49

3.5 Replacing the Front Panel Board.......................................... 51

3.5.1 Front Panel Board Features ............................................ 53

3.5.2 Front Panel Board Connector Pin Definition ................... 53

3.6 Replacing the System Fan.................................................... 54

3.7 Replacing the SATA Backplane Board................................. 56

8

http://www.tyan.com

3.7.1 SATA Backplane Board Features.................................... 58

3.7.2 SATA Backplane Board Connector Pin Definitions ......... 59

3.8 Replacing the Power Supply................................................. 61

Appendix I: Cable Connection Tables .......................................... 63

Appendix II: FRU Parts Table ........................................................65

Appendix III: Technical Support.................................................... 67

9

http://www.tyan.com

Chapter 1: Overview

1.1 About the TYAN YR190-B8238

Congratulations on your purchase of the TYAN

®

YR190-B8238, a highly

optimized rack-mountable barebone system. The YR190-B8238 is

designed to support two AMD

®

32nm 16-Core/12-Core/8-Core/4-Core

Opteron 6200 Series Processors and up to 48GB RDIMM / 48GB UDIMM

DDR3-800/1066/1333/1600 memory per node, providing a rich feature set

and incredible performance. Leveraging advanced technology from Intel

®

,

YR190-B8238 server system is capable of offering scalable 32 and 64-bit

computing, high bandwidth memory design, and lightning-fast PCI-E bus

implementation. The YR190-B8238 not only empowers your company in

nowadays IT demand but also offers a smooth path for future application

usage.

TYAN

®

is also proud to deliver the YR190-B8238 in flavor while

supporting up to eight hot-swap hard drives (four per node). The

YR190-B8238 uses TYAN

®

’s latest chassis featuring a robust structure

and a solid mechanical enclosure. All of this provides YR190-B8238 the

power and flexibility to meet the needs of nowadays server application.

10

http://www.tyan.com

1.2 Features

TYAN YR190B8238 (B8238Y190X2-045V4HI)

Form Factor 1U Rackmount

Chassis Model YR190

Dimension (D x W

x H)

28.74" x 17.32" x 1.72" (730 x 440 x 43.6mm)

Blade Dimension

(D x W x H)

28.74" x 8.46" x 1.61" (730 x 214.8 x 40.8mm)

Motherboard S8238GM2NRI

Board Dimension 6.3"x18" (160x457.2mm), per blade

Gross Weight 25 kg

System

Feature Two nodes in one chassis

Buttons (1) RST / (1) PWR / (1) UID

LEDs (1) PWR / (1) BMC / (2) LAN / (1) HDD

Front Panel (per

blade)

I/O Ports (2) USB ports

Type / Q'ty 2.5" Hot-Swap / (4)

External Drive

Bay (per blade)

Supported HDD

Interface

SATA-II 3.0Gb/s

System Cooling

Configuration

(per blade)

FAN (3) 4cm fans

Type ERP1U cold-swap

Input Range Full-range AC(100-240V)

Frequency 47 - 63 Hertz

Output Watts 450 Watts

Power Supply

(per blade)

Efficiency PFC / 80-plus Silver

Supported CPU

Series

AMD 32nm 16-Core/12-Core/8-Core/4-Core

Opteron 6200 Series Processors (Interlagos)

Socket Type / Q'ty G34 / (2)

Average CPU

Power (ACP)

wattage

Up to 80W

Processor (per

blade)

System Bus Up to 6.4 GT/s Hyper-Transport link support

Chipset (per

blade)

Chipset AMD SR5670 + SP5100

Supported DIMM

Qty

(8)+(4) DIMM slots

DIMM Type /

Speed

U/RDDR3 800/1066/1333/1600 MHz

Memory (per

blade)

Capacity

Up to 192GB

(NOTE: The system does not support DDR3 with

heat spreader.)

11

http://www.tyan.com

Memory channel 2 Channels per CPU

Memory voltage 1.5V/ 1.35V

PCI-E (1) PCI-E Low-Profile Gen.2 x16 slot

Pre-install TYAN

Riser Card

M7018-R16-1L, 1U PCI-E x16 riser card (right)

Expansion Slots

(per blade)

Max. HBA

Dimension (H x L)

(1) 68.90mm x 167.65mm (HH/HL)

Port Q'ty (2)

LAN (per blade)

Controller Intel 82574L

Connector (1) mini-SAS for (4) SATA2

Controller AMD SP5100

Speed 3.0 Gb/s

Storage (per

blade)

SATA

RAID RAID 0/1/10/5 (Promise Integrated RAID)

Connector type D-Sub 15-pin

Resolution 1600x1200@60Hz

Graphic (per

blade)

Chipset Aspeed AST2050

Port Q'ty / Speed (1) QSFP port / 40Gb/s

Chipset Mellanox ConnectX IB MT25408A0-FCCR-QIS

Infiniband (per

blade)

Feature QDR (Quad. Data Rate)

USB (4) ports (2 at front, 2 at rear)

COM (1) DB-9 COM port

VGA (1) D-Sub 15-pin port

RJ-45 (2) ports

I/O ports (per

blade)

Infiniband (1) QSFP Connector

Chipset Winbond W83795G

Temperature

Monitors temperature for CPU & system

environment

LED

Fan fail LED indicator / Over temperature warning

indicator

System

Monitoring (per

blade)

Others Watchdog timer support

Onboard Chipset Onboard Aspeed AST2050

AST2050 IPMI

Feature

IPMI 2.0 compliant baseboard management

controller (BMC) / BIOS update

Server

Management

(per blade)

AST2050 iKVM

Feature

24-bit high quality video compression / Dual 10/100

Mb/s MAC interfaces

Brand / ROM size AMI / 4MB

BIOS (per blade)

Feature

Multiple boot options / Plug and Play (PnP) /PCI2.3

/WfM2.0 /SMBIOS2.3 /PXE boot / ACPI 2.0 power

management /Power on mode after power

recovery / User-configurable H/W monitoring /

Auto-configurable of hard disk types

Operating OS supported list Please visit our Web site for the latest update.

12

http://www.tyan.com

System

FCC (DoC) Class A

Regulation

CE (DoC) Yes

Operating Temp. 10° C ~ 35° C (50° F~ 95° F)

Non-operating

Temp.

- 40° C ~ 70° C (-40° F ~ 158° F)

Operating

Environment

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS

RoHS 6/6

Complaint

Yes

Barebone (1) YR190B8238 Barebone

Manual (1) User's manual

Installation CD (1) TYAN installation CD

Heatsink / Cooler (4) G34 CPU heatsinks

Rail kit (1) sliding rail kit for YR190

Package

Contains

Cable Power Cord

(2) CCBL-0310, US type power cord / (2)

CCBL-0300, EU type power cord

TYAN YR190B8238 (B8238Y190X2-045V4H-LE)

Form Factor 1U Rackmount

Chassis Model YR190

Dimension (D x W

x H)

28.74" x 17.32" x 1.72" (730 x 440 x 43.6mm)

Blade Dimension

(D x W x H)

28.74" x 8.46" x 1.61" (730 x 214.8 x 40.8mm)

Motherboard S8238GM2NR-LE

Board Dimension 6.3"x18" (160x457.2mm), per blade

Gross Weight 25 kg

System

Feature Two nodes in one chassis

Buttons (1) RST / (1) PWR / (1) UID

LEDs (1) PWR / (1) BMC / (2) LAN / (1) HDD

Front Panel (per

blade)

I/O Ports (2) USB ports

Type / Q'ty 2.5" Hot-Swap / (4)

External Drive

Bay (per blade)

Supported HDD

Interface

SATA-II 3.0Gb/s

System Cooling

Configuration

(per blade)

FAN (3) 4cm fans

Type ERP1U cold-swap

Power Supply

(per blade)

Input Range Full-range AC(100-240V)

13

http://www.tyan.com

Frequency 47 - 63 Hertz

Output Watts 450 Watts

Efficiency PFC / 80-plus Silver

Supported CPU

Series

AMD 32nm 16-Core/12-Core/8-Core/4-Core

Opteron 6200 Series Processors (Interlagos)

Socket Type / Q'ty G34 / (2)

Average CPU

Power (ACP)

wattage

Up to 80W

Processor (per

blade)

System Bus Up to 6.4 GT/s Hyper-Transport link support

Chipset (per

blade)

Chipset AMD SR5650 + SP5100

Supported DIMM

Qty

(8)+(4) DIMM slots

DIMM Type /

Speed

U/RDDR3 800/1066/1333/1600 MHz

Capacity

Up to 192GB

(NOTE: The system does not support DDR3 with

heat spreader.)

Memory channel 2 Channels per CPU

Memory (per

blade)

Memory voltage 1.5V/ 1.35V

PCI-E (1) PCI-E Low-Profile Gen.2 x16 slot

Pre-install TYAN

Riser Card

M7018-R16-1L, 1U PCI-E x16 riser card (right)

Expansion Slots

(per blade)

Max. HBA

Dimension (H x L)

(1) 68.90mm x 167.65mm (HH/HL)

Port Q'ty (2)

LAN (per blade)

Controller Intel 82574L

Connector (1) mini-SAS for (4) SATA2

Controller AMD SP5100

Speed 3.0 Gb/s

Storage (per

blade)

SATA

RAID RAID 0/1/10/5 (Promise Integrated RAID)

Connector type D-Sub 15-pin

Resolution 1600x1200@60Hz

Graphic (per

blade)

Chipset Aspeed AST2050

USB (4) ports (2 at front, 2 at rear)

COM (1) DB-9 COM port

VGA (1) D-Sub 15-pin port

I/O ports (per

blade)

RJ-45 (2) ports

Chipset Winbond W83795G

System

Monitoring (per

blade)

Temperature

Monitors temperature for CPU & system

environment

14

http://www.tyan.com

LED

Fan fail LED indicator / Over temperature warning

indicator

Others Watchdog timer support

Onboard Chipset Onboard Aspeed AST2050

AST2050 IPMI

Feature

IPMI 2.0 compliant baseboard management

controller (BMC) / BIOS update

Server

Management

(per blade)

AST2050 iKVM

Feature

24-bit high quality video compression / Dual 10/100

Mb/s MAC interfaces

Brand / ROM size AMI / 4MB

BIOS (per blade)

Feature

Multiple boot options / Plug and Play (PnP) /PCI2.3

/WfM2.0 /SMBIOS2.3 /PXE boot / ACPI 2.0 power

management /Power on mode after power

recovery / User-configurable H/W monitoring /

Auto-configurable of hard disk types

Operating

System

OS supported list Please visit our Web site for the latest update.

FCC (DoC) Class A

Regulation

CE (DoC) Yes

Operating Temp. 10° C ~ 35° C (50° F~ 95° F)

Non-operating

Temp.

- 40° C ~ 70° C (-40° F ~ 158° F)

Operating

Environment

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS

RoHS 6/6

Complaint

Yes

Barebone (1) YR190B8238 Barebone

Manual (1) User's manual

Installation CD (1) TYAN installation CD

Heatsink / Cooler (4) G34 CPU heatsinks

Rail kit (1) sliding rail kit for YR190

Package

Contains

Cable Power Cord

(2) CCBL-0310, US type power cord / (2)

CCBL-0300, EU type power cord

1.3 Product Model

Model HDD Bays Power supply

YR190-B8238

(two nodes)

Hot-swap, 8 HDDs

2 x 450 Watts

(110-240VAC)

15

http://www.tyan.com

1.4 Standard Parts List

This section describes the YR190-B8238 package contents and

accessories. Open the box carefully and ensure that all components are

present and undamaged. The product should arrive packaged as

illustrated below.

1.4.1 Box Contents Per Node

Component Description

1U chassis, 2 nodes

(4) hot swap HDD bays per node

TYAN

®

S8238 system board

(pre-installed)

450 Watts (110-240VAC)

Power Supply (pre-installed)

(3) 40x56mm System Fans

(pre-installed)

Power Distribution Board

(pre-installed)

SATA HDD Backplane Board

(pre-installed)

M7018-R16-1L PCI-E Riser Card

(pre-installed)

Front Panel Board

(pre-installed)

16

http://www.tyan.com

1.4.2 Accessories

If any items are missing or appear damaged, contact your retailer or

browse to TYAN

®

’s website for service: http://www.tyan.com

The web site also provides information of other TYAN

®

products, as

well as FAQs, compatibility lists, BIOS settings, etc.

TYAN

®

Motherboard Drive CD x 1

Heat sink x 4

AC Power Cord 125V x 2 (US)

AC Power Cord 250V x 2

(Europe)

Barebone Manual Mainboard Manual

HDD Screws

17

http://www.tyan.com

Rail Kit

Rail x 2 Screw Pack

18

http://www.tyan.com

1.5 About the Product

The following views show you the product.

1.5.1 System Front View (Per Node)

HDD LED Description

Activity LED: Off

Fault LED: Off

No HDD activity

Activity LED: blinking green

Fault LED: Off

HDD activity

Activity LED: Off

Fault LED: Red

HDD Fail

Activity LED: random

Fault LED: blinking red @ 4 Hz

Identify

Activity LED: random

Fault LED: blinking red @ 1 Hz

Rebuild

19

http://www.tyan.com

Front Panel LED Description

1. HDD

Green: Ready

Blinking Green: Activity

2. LAN2

Green: Link

Blinking Green: Activity

3. LAN1

Green: Link

Blinking Green: Activity

4. IPMI

Green: Normal Status

Amber: Failed System Warning caused by

HDD/BMC/FAN failure, thermal problem, etc

5. Power

Green: Power ON

Blue: ID LED

Front Panel Button Description

6. Power On/ Off Power up and power down the system

7. ID (UID)

Press the ID (UID) button once and the dual-color

Power LED on the front panel and the blue ID LED

on the rear panel will turn blue. Press the button

again to stop.

8. Reset Press to reset the system

20

http://www.tyan.com

1.5.2 System Rear View (Per Node)

 blue ID LED: When the ID (UID) button on the front panel is

pressed, the dual-color Power LED and the blue ID LED will

turn blue. The technical personnel can easily locate the system

on the rack, disconnect cables from the system, and remove it

from the rack for later repair.

LAN LED: The two onboard Ethernet ports have green and amber

LEDs to indicate LAN status. The table below illustrates the

different LED states.

Ethernet LAN Link/Activity LED Description

Left: slow blinking green

Right: Off

10 Mbps Link

Left: blinking green

Right: Off

10 Mbps Activity

Left: slow blinking green

Right: green

100 Mbps Link

Left: blinking green

Right: green

100 Mbps Activity

Left: slow blinking green

Right: amber

1000 Mbps Link

Left: blinking green

Right: amber

1000 Mbps Activity

Left: Off

Right: Off

No Link

Page is loading ...

Tyan YR190-B8238 Service Engineer's Manual

Tyan YR190-B8238 Service Engineer's Manual

Related papers

Other documents