Ibanez Artist Series ART2EX1 User manual

Type
User manual
Table of Contents
Instruction Manual
NGLISH 2 ..................................................... 2
NGLISH 2 .............................................................. 4
NGLISH 2 ............................................................................... 6
ENGLISH Maintenance Manual ....................................................................... 15
Adjustment Manual .......................................................................... 17
DEUTSCH Wartungs- und Pflegehinweise ....................................................... 28
Einstellungsanleitung ......................................................................30
FRANÇAIS Manuel d'entretien ........................................................................... 41
Réglage manuel ............................................................................... 43
ESPAÑOL Manual de mantenimiento ............................................................... 54
Manual de ajustes ............................................................................ 56
ITALIANO Manuale di manutenzione ............................................................... 67
Manuale di regolazione....................................................................69
Maintena 2 .................................................................................80
a 2
......................................................................................... 82
Guitar Electronics
..................................................................................93
Guitar Controls
........................................................................................95
Thank you for purchasing an Ibanez guitar. In order to keep your guitar in
the best possible condition, please read this manual for information on
care and adjustment.
ᆒઐۣዸ၄ݿ
ࢯᑳ၄ݿ
ᒦᆪ
15
ENGLISH
FX_EDGE3_8_English
Maintenance
Our congratulations and deepest thanks on making Ibanez your choice of instrument.
Ibanez standards are second to none. All Ibanez instruments are set up to our strict quality
control standards before shipping. The purpose of this manual is to explain how to
maintain your instrument’s finish and to keep your guitar playing as well as it did when it
left our factory.
CLEANING
Regular cleaning of your guitar is one the most important ways
you can maintain the finish and lengthen string life. After
playing, wipe down your instrument to remove any perspiration
from the instrument. Perspiration can actually contain acids
that can be corrosive to the strings and metal parts of the
guitar. Gloss finish guitars should be polished with polish
formulated specifically for musical instruments, and a soft,
treated guitar cloth or a cotton rag. Abrasive rags such as
polyester can scratch the finish. Oil finished guitars should be
wiped clean immediately after playing with a dry cotton rag only. If your guitar has become discolored due to
extended use or heavy perspiration, factory appearance, see a qualified guitar repair person about methods to
restore the oil finish to its original factory appearance.
STRINGS AND TUNING MACHINES
If strings become dirty, discolored, or produce a dull sound or buzz, replace the
strings with new ones. For best results we recommend replacing one string at a
time, this will help to avoid removing the string tension from the neck. When
replacing strings with different gauge strings, it may be necessary to adjust the
truss rod tension. (We recommend only qualified technicians perform this.)
Instruments that have tremolo systems installed may need to be adjusted after
string replacement as changes in string tension can cause the tremolo to raise
or lower. Ibanez guitars and basses are factory equipped with the following
string gauges. Please follow the instructions below for your particular model.
The strings should be tightly wound on to the tuning machines from top to
bottom with 2 to 3 string wraps around the post. In the case of unwound guitar
strings, the ends of the strings should be prepared as shown in the diagram to
prevent unintentional slippage from the posts. In the case of tuning machines,
where the string ends are inserted into the posts, the string can be cut to length
in advance using a pair of string cutters.
If the tuning machines are sealed gear units, they are self-lubricating types. The set screws for the tuning knob
are adjustment screws that can be tightened with a small Phillips head screwdriver to increase the tension.
*The use of coarse strings may lead to buzzing and sound distortion. Using strings that have twists or kinks may cause buzzing or
decreased sustain. Make sure that the new strings are smooth and free from any defects before installing.
TIGHTEN
LOOSEN
1
2
3
STRING GAUGES
Solid guitars w/Tremolo, NDM2, JTK & ALL Gio
RG321MH, SZR, AXS, AR, ART, ARX, VBI & IC
7-String model
MMM1
MTM1
MTM2
ARTCORE guitars
Bass guitars (AFB, AGB, ARTB)
.009/.011/.016/.024/.032/.042 inch
.010/.013/.017/.026/.036/.046 inch
.010/.013/.017/.026/.036/.046/.054 inch
.014/.017/.030/.040/.056/.074 inch
.011/.014/.018/.028/.038/.049 inch
.011/.015/.018/.028/.038/.054 inch
.010/.013/.017/.030/.042/.052 inch
.050/.070/.085/.105 inch
16
FX_EDGE3_8_English
NECK
Ibanez steel string models are equipped with adjustable truss
rods. The purpose of a truss rod is to adjust the neck to
counteract string tension. There are many reasons for truss rod
adjustments. One of the most frequent reasons is changing string
gauges or tuning pitch which can affect string tension. String
tension changes may affect the string height and cause fret buzz
or notes that don’t ring true. To adjust the truss rod, locate the
truss rod nut and adjust it by inserting the correct wrench into the
nut and tightening (clockwise) or loosening (counter clockwise)
the rod. Truss rod tension can be measured by installing a capo at the first fret the
holding the strings down at the fret position where the neck joins the body. Insert a
thickness gauge between the string and the fret at the 8th fret. There should between
0.3 mm to 0.5mm clearance. That clearance is referred to as “neck relief. Too much
neck relief can cause the neck to have higher action in the middle of the neck causing
poor intonation and uncomfortable playability. No neck relief can cause fret buzz.
*Appropriate care must be taken when adjusting the neck and we recommend only qualified technicians
perform this procedure.
ACTION
Ibanez guitar and bass string action is set at the factory. However there are many
reasons that an instrument’s string height can change. Instruments can be affected by
changes in temperature and moisture. High string action can make the guitar difficult to
play. If the string action is too low, fret buzz or unclear notes can occur. To remedy this,
follow the instructions for the particular type of bridge installed. In the case of string
action, make sure the guitar is in tune and the truss rod is adjusted properly. Ibanez
action is set at the guitar 14th fret bass 12th fret. The action may also need to be
readjusted after the neck has been adjusted or strings have been changed to a different
gauge. Follow the instructions in the relevant bridge manual to make adjustments.
*If strings other than those described above are used, gradually increase the action clearance from the treble
side through to the bass side.
0.3~0.5mm
8th fret
LOOSEN
TIGHTEN
LOOSEN
TIGHTEN
LOOSEN
TIGHTEN
LOOSEN
TIGHTEN
.009-string's guitars except Gio Ibanez
all Gio Ibanez & .010-, .014- string's guitars
Bass guitars (AFB, AGB, ARTB)
1.5mm
1.7mm
2.0mm
2.0mm
2.3mm
2.5mm
TREBLE SIDE BASS SIDE
INTONATION
Intonation adjustment is the operation of adjusting the
location of the string at the saddle to compensate for different
string gauges or different tunings. Follow the instructions of
the particular bridge intonation below. Intonation is properly
set when the 12th fret note and the 12th fret harmonic are
exactly the same note . This is the center point of the scale
and the most accurate way of setting a standard scale length.
With the harmonic note as the standard, if the fretted note is
flat move the bridge saddle forward toward the headstock (a) to decrease the string length. If the fretted note is
sharp, move it back away from the headstock (b) to increase the string length intonation adjustments.
*Please note that strings can be broken when the saddle is moved, so always loosen the strings before making adjustments.
17
ENGLISH
FX_EDGE3_8_English
Guitar Bridges
GIBRALTAR CUSTOM BRIDGE
The height adjustment can be adjusted by 4 pcs of 2.0mm of allen screws (B) on the
bridge. Since the adjustment screws are locked by the bridge lock screw (A), you must
loosen the bridge lock screw by 3.0mm Allen wrench before adjustment.
Each saddle is also locked by a saddle lock screw (C). To adjust the intonation, use a
2.0mm Allen wrench to loosen the saddle locke screws, and then adjust the Intonation
screw (D) by a 2.0mm Allen wrench. When you are finished with the adjustment, lock the
saddle and tune the guitar.
* The same should be applied for the seven string version.
A
B
C
D
PICKUPS
The output level of the instrument as well
as the quality of the signal can be affected
by the pickup height. Pickup height should
be adjusted until the volume of neck and
bridge pickups are almost equal with both
volumes wide open. The volume may drop
drastically if the pickup height is too low.
As the pickups are magnetic, fret buzzing
and distortion may occur if the pickup is
too close to the strings. Use a small screwdriver to make adjustments to raise or lower the pickup.
*Instruments that have adjustable pole pieces can be adjusted to balance the output of each string.
Below is the standard location of the bridge for AF, AFS and AG guitars.
Adjust the location to obtain proper intonation.
AGAF, AFS, AK AFB
BATTERY
For guitars with Pre-Amps or EQs, please use 006P (9V) or AA (1.5V) high-quality batteries according to your
guitar's specifications. Batteries are located either in a battery box or inside the control cavity of your instrument.
Old batteries or batteries with a low-charge should be replaced as they can cause poor sound performance
including low volume and unwanted distortion.
The output plug of your instrument also acts as power switch for the battery: when a guitar cable is plugged in,
the battery will be connected and then disconnected when the guitar cable is unplugged from the output jack.
Attention
If your guitar or bass requires two batteries, do not use a new battery and with an old battery together. Do not use any
combination of different battery types such as an alkaline battery with a carbon battery, or alkaline battery with a
rechargeable battery, etc.
Unplug your instrument when not in use for extended periods. For the longest battery life and to prevent battery fluid
leakage, which could damage your instrument, always unplug your cable from your guitar or bass when it will be
unplayed for long periods of time.
To avoid unwanted noise and possible speaker, electronics or hearing damage, always turn the volume control to the
off position ("0") on your amp or any device your instrument is connected to when unplugging the cable from the
output jack of your guitar or bass.
* The non-alkaline battery(s) your instrument may come with is for circuit testing purposes only and should be replaced.
18
FX_EDGE3_8_English
GIBRALTAR III (GUITAR & BASS),
CB3, & FULL TUNE III, ART1, ART2
The action can be adjusted by using a slot
head (-) screwdriver to turn the adjustment
bolt at either end (A).
Intonation can be adjusted by moving the
saddle forward or backward by turning the
intonation adjustment screw (B) at the rear
of the bridge. You can use either a Phillips
(+), a flat head (-) screwdriver, or the
optional hex wrench.
HARDTAIL BRIDGE
To change strings, thread the new strings through the string grommets
located on the back of the guitar and bring them up and over the saddle.
The intonation can be adjusted by adjusting the saddle forward or
backward using a Phillips (+) head screwdriver on the intonation
adjustment screw at the rear of the bridge. String height is controlled by
raising or lowering the small Allen screws using a wrench on either side
of the saddle.
(A)
(B)
(A)
ADJUSTABLE ARCH TOP BRIDGE
The string height of an arch top bridge can be adjusted by turning the
thumb wheel screws located on either side of the bridge. Clockwise
lowers the string action; counter clockwise raises the string action.
As the bridge is not fixed to the body, intonation can be adjusted by
loosening the strings and moving the location of the bridge forward or
backward.
(B)
REPLACING THE STRINGS : CB3
Install strings by inserting them from the front of the bridge.
GIBRALTAR III, CB3
FULL TUNE II,
ART1, ART2
GIBRALTAR STANDARD
There are two methods to attach the strings: One method is to thread
the strings through the string grommets located on the back of the
guitar, and the other is to hook and stop the ball-end on the back of the
bridge (A).
To adjust the height of the strings, use a 1.5mm hexagonal wrench to
turn and adjust the height of each saddle (B).
To adjust the intonation, use a 2.5mm hexagonal wrench to turn the
intonation adjustment screws of each saddle on the back of the bridge
(C).
(B)
(C)
(A)
19
ENGLISH
FX_EDGE3_8_English
QUIK CHANGE III
QUIK CHANGE MINI
QUIK CHANGE ULTRA / FINE TUNNING FUNCTION
QUIK CHANGE ULTRA has FINE TUNER function.
Even after by the tuning machine, you can make a quick-fine
adjustment by FINE TUNERS (E).
QUIK CHANGE CLASSIC
QUIK CHANGE ULTRA
(C)
(E)
Tailpieces
QUIK CHANGE TAILPIECES
The height adjustment of the QUIK CHANGE III can be adjusted by using a
slot head (-) screwdriver or a coin turn the adjustment studs at either
side of the tailpiece (C).
Vintage Vibrato
For best results we recommend replacing one string at a time. This will
help to avoid removing the string tension from the neck and keep the
vibrato spring under tension.
To replace the strings on the VBX60 or VBS80, thread the new string
under the front tailpiece retainer bar (A).
The ball end of the string should be threaded over and around the rear
tailpiece retainer bar (B).
The ball end of the string’s hole is inserted into the rear tailpiece
retainer bar pin and the string should be pulled tight towards the
headstock. Releasing the string tension from the tailpiece may cause
the ball end to slip off the pin. Keeping string tension on the string by
pulling it towards the headstock will alleviate this problem.
Thread the string through the machine head and while keeping tension
on the string, wind the string around the post. Make sure that the string
lands on the proper string saddle on the bridge. Once tight, tune the
string to pitch. Repeat this process for the other strings.
(B)
(A)
VBX60
VBS80
VBF70
(B)
DOWNSHIFTER
INSTALLING THE STRING
To install a new string insert the ball end of the new string into the slot and place the
ball end into the internal hook area of the saddle as shown. Pull the string tight to the
saddle and restring the rest of the string as you normally would on the machine head.
SPECIAL TUNING
The Downshifter also allows the pitch to be raised by setting the standard tuning
while the lever is in the lower position. When the lever is raised the pitch will also be
1
2
3
20
FX_EDGE3_8_English
raised and can be adjusted to the desired pitch.
The Ibanez DOWNSHIFTER allows the pitch of a string to be dropped to a preset
desired position with a simple lever operation. To achieve precise tuning for both the
up and down positions, you will need to preset both lever settings before operating
the Downshifter.
TUNING
First check that the Downshifter lever arm is raised to the up position then tune the
string normally using the standard tuning machines on the headstock.
(Note: the Downshifter tuning screw has no effect on the pitch in the up position.)
Next, lower the lever on the Downshifter to the down position and the pitch of the
string will drop down. Adjust the rear tuning screw clockwise to reduce the pitch, or
counter clockwise to raise the pitch. This adjustment can be done by hand or with a
standard screwdriver or a coin until the desired down pitch is acquired. (The preset
factory pitch is set one whole step down to D.) When the lever is raised to the up
position, the thumbscrew can be turned freely but will have no effect on the raised
lever pitch. However, it will affect the settings of down lever pitch.
PLEASE NOTE: The Downshifter device was designed to provide the highest level of pitch accuracy. However, it
should be understood that the Downshifter is a mechanical device. Pitch variations and tuning readjustments,
especially after frequent use, are to be expected.
TIGHT-TUNE BRIDGE
The Tight-Tune bridge achieves the optimum in stability and sound transference while suppressing unnecessary
vibrations by allowing each part of the bridge to be locked.
STRING HEIGHT ADJUSTMENT
*
String height can be adjusted by loosening the lock nut (A) on both sides of
the bridge and turning the stud bolt (B) with a 3mm hexagonal wrench (E).
After adjusting the string height, tighten the lock nut (A).
NOTE: * Always be sure to unlock the interior stud lock screw before adjusting the string
height. Otherwise, damage may occur.
STUD LOCK FUNCTION
The Tight-Tune Bridge has a stud lock function. This fixes the stud bolt (B) to
the guitar body securely after finishing string height adjustment.
Before performing string height adjustment, completely loosen the stud lock
screw located on the interior of the bridge stud (F) in a counter-clockwise
direction using a 2mm hexagonal wrench (H). After finishing the string
height adjustment, turn the interior stud lock screw clockwise (F). When the
screw touches the anchor nut (G) and cannot be turned further, it is locked.
INTONATION ADJUSTMENT
To adjust the location of the saddle, loosen the saddle lock bolt (C) on the
saddle to be adjusted and turn the intonation adjustment screw (D). Tighten
the saddle lock bolts again (C) after finishing adjustment.
*Hint: Resonance may occur if the intonation adjustment screw (D) is loose. In this case,
lightly tighten the intonation adjusting screw (D) until the saddle does not move.
REPLACING THE STRINGS
The Tight-Tune tailpiece is equipped with a ball-end lock function, which
doesn't allow the ball-end to separate from the tailpiece when replacing the
strings. When installing the string, insert the ball-end into the slot of the
tailpiece as shown in Fig. 1. The string can be removed easily by pulling it in
the direction as shown in Fig. 2.
1
2
21
ENGLISH
NOTE
*Although the string height of the guitar can be raised or lowered up to 0.3mm to 0.5mm with a rotation of the studs, it is recommended
that the adjustments be made in smaller increments.
*The string height may change after the final adjustment of the rear stud. It is recommended to check the final string height after the rear
stud is adjusted.
MAIN STUD
REAR STUD
MAIN STUD
PARALLEL
Locking Tremolos
EDGE III TREMOLO
TREMOLO ARM INSTALLATION
The tremolo arm can be inserted and removed very easily. Insert the arm into the
armhole on the tremolo base plate. Pull up on the arm to remove it.
ARM ROTATION TORQUE
The rotation torque of the arm can be adjusted by raising the tremolo and
inserting a 2 mm Allen wrench in the screw (A) on the tremolo block, turning this
screw clockwise will tighten the arm torque and turning the screw counter
clockwise will loosen the arm torque.
(A)
Locking Bridge
FX EDGE, FX EDGE
III -FIXED BRIDGE
The Ibanez FX-Edge Bridge is a fixed, double locking bridge, based on
the popular Ibanez Lo-Pro Edge Tremolo. Please read the instructions
below regarding the use and proper adjustment of the bridge.
THREE STUD SYSTEM
Three studs support the FX-Edge Bridge; two main studs and one
smaller, rear stud. The rear stud helps to lock the bridge in place and
also passes additional string vibration through the body.
STRING HEIGHT ADJUNSTMENT
String height can be adjusted by raising or lowering all three studs.
After adjusting the height of the two main studs, the rear stud must be
compensated by using the provided 3mm Allen key to keep the angle
of the bridge in proper alignment. (The bridge should sit parallel to the
body.)
22
FX_EDGE3_8_English
ARM ACTION
The tremolo arm action can be adjusted by using a 3.0mm Allen wrench on the screw
(B) of the tremolo screw.
FINE TUNING
Even after locking the locking nut, you can use the fine tuners to make fine
adjustments to the tuning of each string. You should adjust all of the fine tuners (C) to
the center of adjustable range before you lock the locking nut.
ADJUSTING THE ACTION
To adjust the entire tremolo unit up or down, use an Allen wrench to turn the stud
bolt (E) located at the left and right of the tremolo unit. (This cannot be adjusted for
each individual string.)
ADJUSTING THE INTONATION
Loosen the Pressure pad screw (D) on the locking nut and loosen the string to be
adjusted. Loosen the Saddle lock screws (F) on the saddle to be adjusted and adjust
the saddle forward or backward. Tighten the Saddle lock screw (F) and tune the
string. After rechecking the intonation, tighten the Pressure pad screw (D).
*On the base plate there are two holes for each Saddle lock screw. These allow the user to change string
gauges while allowing thee maximum saddle movement. If the intonation cannot be adjusted because
the saddle needs to be set back further, remove the intonation screw and insert it into the hole located
further back on the bridge plate.
REPLACING THE STRINGS
In the case of EDGE III tremolo, replace the strings one by one. Removing all the old
strings at once will release the tension on the tremolo and change the tremolo angle
“up-pull.” Loosen the Pressure pad screw (D) on the locking nut and loosen the string
to be replaced. Loosen the String stopper screw (G) and remove the string from the
saddle. Cut off the ball end of new string as shown on the illustration and insert the
cut side of new string between the saddle and the String holder block.Tighten the
String stopper screw (G) and tune the string. After checking the intonation, tighten
the Pressure pad screw (D) on the locking nut.
EDGE III ADJUSTING THE TREMOLO SPRING
The tremolo springs adjust the tremolo angle by tightening or loosening the tremolo
tension. To adjust tremolo angle, locate the adjustment screws in the rear tremolo
cavity. The tremolo system when in tune should sit parallel to the surface of the
guitar as follows. If the tremolo system is not sitting parallel to the surface of the
guitar, remove the tremolo cavity cover plate and
tighten the Tremolo tension adjustment screws if the tremolo is forward
dumped. Loosen the screws if the tremolo is up-pulled.Retune the strings to
the proper pitch and check the angle. Choose the number and placement of the
tremolo springs according to the string gauge and the tremolo angle.
(B)
(G)
(C)
(F)
(E)
(D)
23
ENGLISH
FX_EDGE3_8_English
ZR (ZERO RESISTANCE) TREMOLO
TREMOLO ARM
Loosen the screw cap, insert the arm
into the tremolo unit, and rotate it to
fasten it in place (Fig.8). Rotate the arm
to adjust it to the desired height. The
arm torque is adjusted by the tightness
of the screw cap. To remove the arm,
loosen the screw cap and rotate the
arm counter-clockwise (Fig.9).
FINE TUNING
Even after locking the locking nut, you can use the fine tuners (Fig.10 A) to
make fine adjustments to the tuning of each string.
You should adjust all of the fine tuners to the center of their adjustable
range before you lock the locking nut.
ADJUSTING THE ACTION
To adjust the entire tremolo unit up or down, use an Allen wrench to turn
the stud bolt (Fig.10 B) located at the left and right of the tremolo unit.
(This cannot be adjusted for each individual string.)
ADJUSTING THE INTONATION
Loosen the string stopper bolt of the locking nut (Fig.11). Remove the
intonation adjustment bolt (Fig.12 B) from within the bridge unit, fasten it
into the screw hole in the rear of the saddle, and tighten it so that the tip
of the bolt contacts the boss of the bridge unit. Loosen the saddle lock bolt
(Fig.10 C), and turn the intonation adjustment bolt to adjust the position of
the saddle. After completing the adjustment, tighten the saddle lock bolt
sufficiently to prevent the saddle from moving forward during tuning, and
store the intonation adjustment bolt inside the bridge unit.
REPLACING THE STRINGS
Loosen the string stopper bolt of the locking nut (Fig.11), completely
loosen the string at the tuning machine, use an Allen wrench to loosen the
string stopper bolt of the bridge saddle (Fig.12 A), and remove the old
string. Use wire cutters to remove the ball end from the new string as
shown in Figure 13, insert this end of the string into the bridge saddle,
fasten it firmly, and then tighten the string at the tuning machine. After
tuning, check the angle of the tremolo unit, and fasten the string stopper
bolt of the locking nut to finish the procedure.
ADJUSTING THE ZERO POINT SYSTEM
The Zero Point system makes it easier to tune a floating tremolo unit,
provides greater tuning stability after arming, and limits the tuning drift
that would otherwise occur when a string breaks.
*If the Zero Point system is not adjusted to the correct position it will not
function optimally, since it will either be completely floating, or the Zero
Point system and the string tension will be in balance. You must perform
this adjustment accurately.
A
B
C
FIG.8
FIG.11
FIG.13
FIG.12
FIG.10
FIG.14
FIG.9
24
FX_EDGE3_8_English
Main Spring
Tremolo Block
Stop Rod
Stopper
2
1
SWITCHING TO FLOATING OPERATION
By stopping the Zero Point system from functioning, you can make the
tremolo float completely. While holding the arm up, remove the stop rod
and sub spring. With the guitar tuned correctly, use the main spring
adjustment knob (Fig. 14E) to adjust the angle of the tremolo unit. If the
tremolo unit is tilted forward toward the neck, turn the spring adjustment
knob in the plus (+) direction. Conversely, if the tremolo unit is tilted
backward away from the neck, turn the spring adjustment knob in the
minus (-) direction.
*You will need to tune repeatedly during the process of adjusting the
tremolo angle in the floating state, since the tuning will drift each time you
adjust the main spring adjustment knob.
With the guitar tuned correctly, adjust the Main Spring make
sure that the Stop Rod makes contact with the Tremolo
Block and Stopper.
If the Stop Rod does not make contact with the Tremolo
Block and Stopper, adjust the Main Spring adjustment
screw until contact is made.
With the guitar tuned correctly, Stop Rod must make contact
with the Tremolo Block and Stopper. If it is adjusted
correctly, the tension while pushing down on the arm will be
slightly less than tension while pulling up.The balance of
force is about 3:7 (With this setup, stop rod must the
tremolo block and stopper even the 1st string is completely
loosened.)
Again, if the Stop Rod does not make contact with theTremolo
Block and Stopper, adjust the Main Spring adjustment
screwuntil contact is made.
<Note>
When a string breaks,because of the tension of neck,the tuning of other strings will be a little higher butstill limits within acceptable range.
ZPS (ZERO POINT SYSTEM) OF ZR TREMOLO
25
ENGLISH
FX_EDGE3_8_English
FAT/SAT TREMOLO
TREMOLO ARM INSTALLATION
The tremolo arm can be inserted and removed very easily. Insert the arm into
the armhole on the tremolo base plate. Pull up on the arm to remove it.
TREMOLO ARM ADJUSTMENT (SAT PRO2)
To adjust the height of the arm, remove the tremolo spring cover from the back
of the guitar, and use a 3 mm Allen wrench to turn the height adjustment screw
attached to the bottom of the tremolo block. Tightening this in the clockwise
direction will raise the height.
ARM ROTATION TORQUE
The rotation torque of the arm can be adjusted by raising the tremolo and
inserting a 1.5mm Allen wrench in the screw (A) on the tremolo block, Turning
this screw clockwise will tighten the arm torque and turning the screw counter
clockwise will loosen the arm torque.
ADJUSTING THE STRING HEIGHT (SAT PRO2)
To adjust the action of each string, use a 1.5 mm Allen wrench to turn the screw on the
saddle (C). The overall height can be adjusted on either side of the SAT PRO2 tremolo
unit. To adjust the height, use a 3 mm Allen wrench to turn the stud (D) located on
either side of the unit. Use caution when adjusting the height of the entire tremolo unit;
adjust both sides to the same height to ensure optimum tremolo operation.
ADJUSTING THE STRING HEIGHT (FAT20/FAT10/SAT10)
The height adjustment of the tremolo can be raised or lowered by adjusting the pivot studs (C) that the tremolo
mounts on. These are located at either side of the front of the bridge. Clockwise lowers the tremolo and counter
clockwise raises the tremolo.
INTONATION ADJUSTMENT (SAT PRO2)
To adjust the intonation, use a 1.5 mm Allen wrench to turn the screw located
at the rear of the saddle (E). Turn the screw clockwise to move the saddle
toward the rear, or counter-clockwise to move the saddle forward.
Non Locking Tremolo
(C)
(D)
(E)
(C) (C) (C)
FAT20 FAT10 SAT10
(A)
(C)
(D)
(E)
SAT PRO2
26
FX_EDGE3_8_English
REPLACING THE STRINGS
To replace strings, thread the new strings through the string holes located on
the back of the guitar. The strings are then threaded through the tremolo block
and up and over the saddle.
FAT/SAT (expect FAT6) ADJUSTING THE TREMOLO SPRING
A standard tremolo can be adjusted so that the pitch can be raised when the
tremolo arm is pulled up to loosen the tremolo springs located under the
tremolo cavity on the back of the guitar. One disadvantage of this procedure is
that it can cause the pitch to go sharp if string breaks. To remedy this, adjust
the tremolo plate so it sits flush on the body by tightening the tremolo springs.
Choose the number and placement of the tremolo springs according to the
string gauge and the tremolo adjustment .
(D)
(E)
FAT20
FAT10
INTONATION ADJUSTMENT (FAT20)
To assure that no movement can occur each saddle has a set screw that locks
the saddle. When adjusting the intonation, loosen the saddle lock screw using
a 2mm Allen wrench. (D)
To adjust the intonation, insert a 2.5mm Allen wrench into the saddle screw at
the rear of the tremolo. Turning the wrench clockwise will adjust the saddle
backward. Counter clockwise will adjust the saddle forward. After the correct
intonation location of the saddle is set tighten the saddle lock down screw to
assure no movement will occur. (E)
INTONATION ADJUSTMENT (FAT10/SAT10)
The intonation can be adjusted by adjusting
the saddle forward or backward using a
Phillips (+) head screwdriver on the
intonation adjustment screw at the rear of
the bridge.
ADJUSTING THE INTONATION & THE STRING HEIGHT (FAT 6)
The intonation can be adjusted by adjusting the saddle forward or backward
using a philips(+) head adjustment screw at the rear of the bridge. String height
is controlled by raising or lowering the small allen screws using a wrench on
either side of the saddle.
SAT10
Floating PARALLEL
27
ENGLISH
FX_EDGE3_8_English
ACT TREMOLO
REPLACING THE STRINGS
ACT tremolo allow two styles of string installation.
1) The strings are installed by putting the ball end into the string slot and
hooking the ball end below the string catch at the rear of the tremolo unit.
2) The strings are installed by putting the ball end into the string slot and
hooking the ball end in the string catch at the bottom of the tremolo unit.
This increases string tension and adds sustain.
TREMOLO ARM INSTALLATION
The tremolo arm can be inserted and removed very easily. Insert the arm into the armhole on the tremolo base
plate. Pull up on the arm to remove it.
ARM ROTATION TORQUE
The rotation torque of the arm can be adjusted by raising the tremolo and inserting a 2.0mm Allen wrench in the
screw (A) on the tremolo block. Turning this screw clockwise will tighten the arm torque and turning the screw
counter clockwise will loosen the arm torque.
ADJUSTING THE TREMOLO SPRINGS
ACT Tremolo is designed to function optimally when
it is installed approximately parallel with the
surface of the guitar body. The angle at which the
tremolo is attached can be adjusted by changing the
length of the tremolo springs under the tremolo unit.
Use a Philips (+) screwdriver to turn the tremolo
tension adjustment screws to adjust the length of
the tremolo springs. (B) If the tremolo is tilted
forward toward the neck of the guitar, turn the screws clockwise to tighten the springs. Conversely, if the tremolo
is tilted backward away from the neck, turn the screws counter-clockwise to loosen the springs. Tune the guitar
acctually, re-check the angle of the tremolo, and repeat the adjustment until the tremolo angle is correct.
ADJUSTING THE ACTION
To adjust the entire tremolo unit up or down, use a 3.0mm Allen wrench to turn the stud bolt (C) located at the
left and right of the tremolo unit. (This cannot be adjusted for each individual string.)
ADJUSTING THE INTONATION
Use a 2.0mm Allen wrench to loosen the saddle lock
screws (D) of each saddle, and move the saddle.
Firmly tighten the saddle lock screws, tune the
guitar, and then check the intonation. Repeat these
adjustments until the intonation is correct.
(D)
(C)
(B)
(A)
93
FX_EDGE3_8
NECK SIDE :HUMBUCKER PICKUP MODE
BRIDGE SIDE:HUMBUCKER PICKUP MODE
NECK SIDE :SINGLE PICKUP MODE
BRIDGE SIDE:HUMBUCKER PICKUP MODE
NECK SIDE :HUMBUCKER PICKUP MODE
BRIDGE SIDE:SINGLE PICKUP MODE
NECK SIDE :SINGLE PICKUP MODE
BRIDGE SIDE:SINGLE PICKUP MODE
NECK CENTER BRIDGE
NECK CENTER BRIDGE
VOLUME TONE
VOLUME TONE
VOLUME TONE
VOLUME TONE
NECK CENTER BRIDGE
NECK CENTER BRIDGE
Guitar Electronics
SWITCHING FUNCTION
Ibanez Instruments are unique in the simplicity and
versatility of our switching systems. Each model was
designed to allow the maximum amount of useful
pickup positions with the simplest operations.
SPLITS FUNCTION
WITH "TRUE-DUO"SYSTEM
SAS32EX : 2 PICKUPS (H-H)
NECK CENTER BRIDGE
NECK CENTER BRIDGE
JEM. PGM, RG, GRG, S, NDM, GRX :
3 PICKUPS (H-S-H)
GSA, GRX, SA160 : 3 PICKUPS (S-S-H)
SPLITS FUNCTION
NECK CENTER BRIDGE
NECK CENTER BRIDGE
HUMBUCKER PICKUP MODE
SINGLE PICKUP MODE
TONE POT
SWITCH PUSH DOWN
TONE POT
SWITCH PULL UP
SAS36/SA260 : 3 PICKUPS(S-S-H)
94
FX_EDGE3_8
OTHERS
JS, DN500 : 2 PICKUPS (H-H)
JS : Coilt Tap Switch by TONE POT
Pull up=TAP ON NECK&BRIDGE Both
pickups
NECK CENTER BRIDGE
NECK CENTER BRIDGE
JS (WHEN COIL TAP SWITCH WORKED)
MTM1, APEX2, MMM, RG120, RG or RGT (w/EMG PICKUPS),
RGA32, GSA, GRX, GAX30:
2 PICKUPS (H-H)
NECK CENTER BRIDGE
SZR : 2 PICKUPS (H-H)
NECK CENTER BRIDGE
ART, ARX, AX, AXS, GAX(*), IC, ICT, XPT, JTK, AF, AFS, AK, AG,
AGS, AM, AS, AJD, AFB, AGB, STM1, DTT :
2 PICKUPS (H-H)
(*) except GAX30
NECK CENTER BRIDGE
NECK CENTER BRIDGE
Humbucking is parallel connected.
RG(*), SA120, MTM2, S : 2 PICKUPS (H-H)
(*)except RG120
NECK CENTER BRIDGE
JTK3, DN400 : 2 PICKUPS (S-S)
95
FX_EDGE3_8
VOLUME
TOGGLE SWITCH
TONE
VOLUME
TONE
w/COIL TAP ON/OFF SW.
TOGGLE SWITCH
VOLUME
5 WAY
PICKUP SELECTOR
TONE
Guitar Controls
CONTROLS
1 VOL(*), 1 TONE & 5 WAY LEVER SELECTER 0
*SAS/SA220, 260 : TRUE-DUO SWITCH ON VOLUME
JEM, PGM, NDM, RG, SAS, SA, GSA60, S,
GRX70,40, GRG
1 VOL, 1 TONE & 3 WAY LEVER SELECTER
JS
(*)Coil Tap Switch on Tone
1 VOL, 1 TONE(*) & 3 WAY TOGGLE SWITCH
XPT, ADC, JTK, ICT
1 VOL, 1 TONE & 3 WAY TOGGLE SWITCH
TONE
NECK VOLUME
BRIDGE
VOLUME
TOGGLE SWITCH
NECK TONE
BRIDGE TONE
3 WAY
PICKUP SELECTOR
NECK
VOLUME
BRIDGE VOLUME
ARX, ART, SZR
2 VOL, 1 TONE & 3 WAY TOGGLE SWITCH
AXS, AX, GAX70,75, AS
AF, AFS, AK, AG, AGS, AM
2 VOL, 2 TONE & 3 WAY TOGGLE SWITCH
1 VOL & 1 LEVER SELECTER
VOLUME
3 WAY
PICKUP SELECTOR
TONE
MMM, RG120, GSA20, GRX20, 22, GAX30,
RG or RGT(w/EMG PICKUPS)
3 WAY
PICKUP SELECTOR
VOLUME
MTM1, APEX2 (w/3 way LEVER SELECTOR)
MTM2 (w/5 way LEVER SELECTOR)
AJD, AFB, AGB
1 VOL, 1 TONE & 3 WAY TOGGLE SWITCH
TONE
VOLUME
TOGGLE SWITCH
96
FX_EDGE3_8
1 VOL, 1 TONE, 1 BALANCER
2 VOL, 1 TONE & 3 WAY TOGGLE SWITCH
1 VOL, 1 PRE-SET EQ & 3 WAY TOGGLE SWITCH
FX_EDGE3_8
This is to certify that the aforementioned
equipments fully conform to protection
requirements of the following EC council directives.
DIRECTIVES:89/336/EEC Electromagnetic compatibility
FX_EDGE3_8
WWW.ibanez.com
©2008 Printed in China SEP08689
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101

Ibanez Artist Series ART2EX1 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI