Zinsser 260544 User guide

Type
User guide

Zinsser 260544 is a Tape & Adhesive Remover that can remove all types of tape, stickers, labels and adhesive residue from walls, doors, floors, wood, metal, glass and other painted and non-painted hard surfaces. This product is easy-to-use, is effective, and works in minutes.

To use, place the foam applicator directly onto the tape or adhesive. Lightly squeeze the bottle to wet the foam applicator. Rub the wetted form applicator on the tape, adhesive, sticker, etc. Allow the product to penetrate the tape or adhesive for 2-5 minutes.

Zinsser 260544 is a Tape & Adhesive Remover that can remove all types of tape, stickers, labels and adhesive residue from walls, doors, floors, wood, metal, glass and other painted and non-painted hard surfaces. This product is easy-to-use, is effective, and works in minutes.

To use, place the foam applicator directly onto the tape or adhesive. Lightly squeeze the bottle to wet the foam applicator. Rub the wetted form applicator on the tape, adhesive, sticker, etc. Allow the product to penetrate the tape or adhesive for 2-5 minutes.

TECHNICAL DATA JMX-03
JOMAX
®
TAPE & ADHESIVE REMOVER
Form: CS2145
Rev.: 030713
1
.DESCRIPTION AND USES .
JOMAX® Tape & Adhesive Remover removes all types of
tape, stickers, labels and adhesive residue from walls,
doors, floors, wood, metal, glass and other painted and
non-painted hard surfaces. This product is easy-to-use, is
effective, and works in minutes.
PRODUCTS .
SKU Container Size
260544 4 fluid ounces
PRODUCT APPLICATION .
DIRECTIONS FOR USE
Place the foam applicator directly onto the tape or
adhesive. Lightly squeeze the bottle to wet the foam
applicator. Rub the wetted form applicator on the tape,
adhesive, sticker, etc. Allow the product to penetrate the
tape or adhesive for 2-5 minutes. For tougher jobs, allow
the product to penetrate for 5 minutes. Use a plastic
scraper tool to remove the tape or adhesive from the
surface. Wipe the surface clean with clean rag or towel
and allow the surface to dry.
CAUTION! If respiratory irritation, dizziness, nausea, or
unconsciousness occurs, seek immediate medical
assistance. If eye contact occurs, flush with water for at
least 15 minutes. If irritation persists, seek medical
attention. Do not take internally. If swallowed get medical
attention immediately. Do not induce vomiting. KEEP OUT
OF REACH OF CHILDREN.
DISPOSAL
The empty container can be recycled. If recycling is not
available, discard in trash.
TECHNICAL DATA
JOMAX
®
TAPE & ADHESIIVE REMOVER
Rust-Oleum Corporation Form: CS2145
11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 030713
Vernon Hills, Illinois 60061 www.rustoleum.com
An RPM Company
.PHYSICAL PROPERTIES .
TAPE & ADHESIVE REMOVER
Composition
Petroleum Distillates, D-Limonene
Weight
Per Gallon
8.50 lbs.
Per Liter
1.02 kg
pH
NA
VOC (Based on Consumer
Product Rule)
1.0%
Shelf Life
2 years
Flash Point
>200ºF (93ºC)
Caution!
May cause eye irritation. May be harmful if swallowed. Avoid contact with eyes and
prolonged contact with skin. Do not swallow. Use only with adequate ventilation. KEEP
OUT OF REACH OF CHILDREN.
Safety Information
For additional information, see MSDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The
statements of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use
of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any,
will be limited to replacement of defective materials. All technical information is subject to change without notice.
  • Page 1 1
  • Page 2 2

Zinsser 260544 User guide

Type
User guide

Zinsser 260544 is a Tape & Adhesive Remover that can remove all types of tape, stickers, labels and adhesive residue from walls, doors, floors, wood, metal, glass and other painted and non-painted hard surfaces. This product is easy-to-use, is effective, and works in minutes.

To use, place the foam applicator directly onto the tape or adhesive. Lightly squeeze the bottle to wet the foam applicator. Rub the wetted form applicator on the tape, adhesive, sticker, etc. Allow the product to penetrate the tape or adhesive for 2-5 minutes.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI