A Division of Stevens Lee Company
1600 Xenium Lane North, Minneapolis, MN 55441-3787
Phone (763) 553-1881
Technical Manual
and
Replacement Parts List
Majestic
Milk Dispensers
Specifications Subject to Change Without Notice.
MODEL SK5MAJ
1
TECHNICAL MANUAL
MAJESTIC SERIES BULK MILK DISPENSERS
INSTALLATION, OPERATION AND MAINTENANCE
Thank you for purchasing Silver King food service equipment. Our goal is to provide our customers with the most
reliable equipment in the industry today. Please read this manual and the accompanying warranty information before
operating your new Silver King unit. Be sure to complete and mail the warranty card within 10 days of purchase to
validate your warranty.
Upon delivery of your new Silver King unit, inspect the carton and unit for shipping damages. Report any damage
immediately to the transportation carrier and file a written freight damage claim to protect your investment. If a claim is
to be filed, save all packaging materials.
INSTALLATION
The stainless steel exterior of the cabinet has been protected by a plastic covering during manufacturing and shipping.
This covering can be readily peeled before installation. After removing this covering, wash the interior and exterior
surfaces using a warm mild soapy water solution and a sponge or cloth, rinse with clean water and wipe dry.
Drip Tray:
Follow the instructions supplied with the drip tray for mounting it to the unit.
Location:
When locating your new milk dispenser, convenience and accessibility are important considerations, but the following
factors must be observed:
* When placing the unit on a counter, the counter must be able to support a minimum of 300 pounds.
* When wall mounting the unit, follow the instructions supplied with the wall mounting kit.
* When placed on a counter, the unit must be on the legs supplied and secured to the counter with the Hold Down
Brackets supplied. If the legs are not installed the unit will not operate properly and the warranty will be void.
* There must be at least four (4) inches of clear space above the unit, two (2) inches on each side and back and open
in front.
* At no time should anything be stored or placed on top of the unit.
* Correct serving height is important so that those using the dispenser can operate the dispenser properly.
* The unit must be level. The feet on the front legs are adjustable to aid in leveling the unit.
* Avoid placing the unit next to an oven, heating element or hot air source which would adversely affect the performance
of the unit.
Electrical Connections:
Be sure to check the data plate, located on the liner of the cabinet, for required voltage prior to connecting the unit to
power. The specifications on the data plate supersede any future discussion.
The standard dispenser is equipped with an seven (7) foot power cord that requires a 115 Volt, 60 Cycle, 1 Phase
properly grounded electrical receptacle. The power cord comes with a 3 prong plug for grounding purposes. Any
attempt to cut off the grounding spike or to connect to an ungrounded adapter plug will void the warranty, terminate the
manufacturers responsibility and could result in serious injury.
The circuit must be protected with a 15 or 20 ampere fuse or breaker.
2
OPERATION
Initial startup:
After satisfying the installation requirements, the milk dispenser is ready to start. The unit will start when the power cord
is connected to a live electrical receptacle. If the compressor is not running when the unit is initially plugged in, check
to make sure that the Temperature Control is not set to the off position. Allow the unit to run a minimum of two hours
before loading it with product.
Preparation For Use:
Once the unit has achieved proper operating temperature, observe the procedures noted in the label on the door liner
for loading milk into the milk dispenser. When removing an empty milk krate, be sure to raise the valve arm fully before
pulling the milk tube out of the valve. The last half inch of upward valve travel will lock the valve jaw in place and prevent
it from coming out of the valve.
Temperature Control:
The Temperature Control, located on the front of the unit behind the valve splash guard (see label on door liner), is
factory set at the midpoint position, which will maintain an average product temperature of around 36 - 38 Deg F. To
access the temperature control, follow the instructions on the door liner. To obtain cooler temperatures turn the Tem-
perature Control stem clockwise and vise versa with a flat blade screwdriver. Allow the unit a minimum of six (6) hours
to respond to a control setting adjustment if the product is in the cabinet.
Temperature Indicator:
The Temperature Indicator, mounted on the door, is factory set to indicate the temperature of the product within two (2)
degrees. Should the Temperature Indicator read inaccurately there are instructions for recalibrating it located on the
door liner.
Defrost:
The Silver King Majestic milk dispenser is a manual defrost unit. The unit should be defrosted whenever the walls
accumulate a frost bank that is 1/2 inch thick. To defrost the unit, either turn the Temperature Control knob to the off
position or disconnect the power cord from the electrical receptacle, and open the door. After the frost has melted or
come loose from the cabinet walls, wipe out the cabinet interior. Do not attempt to scrape or chisel off the frost as you
could do irreparable damage to the unit.
Mixers (Optional Equipment/Factory Installed):
The optional malt mixers for the Silver King Majestic milk dispensers have 3 speeds. The speed is adjusted by the 3
position knob on the top of the mixer. To operate the mixer put a mixer cup with product in it under the mixer shaft and
raise it until the lip of the cup engages the cup guide on the mixer. The mixer shaft and impeller will spin when the cup
guide is raised.
MAINTENANCE
Preventative maintenance is minimal although these few steps are very important to continued operation and maximiz-
ing the life of the appliance.
Cabinet Surfaces:
The cabinet interior and exterior are stainless steel and should be cleaned periodically with a solution of warm water
and a mild soap, rinsed and wiped dry with a clean soft cloth. A stainless steel cleaner can also be used. Should a
surface become stained or discolored, do not attempt to clean with an abrasive cleaner or scouring pad. Use a soft
cleaner and rub with the grain of the metal to avoid scratching the surface. Do not use chlorinated cleaners.
Valves:
To clean the valve start by removing the bottom valve body cap (item 32) by prying it down and off. Remove the valve
jaw (item 33) by pushing up through the bottom of the valve and pulling it out the top of the valve. Clean all loose parts
and the valve (in place) with a solution of warm water and mild soap or a sanitizing solution and rinsing afterwards.
Replace the valve jaw by sliding it into the valve from above and pressing down on the valve jaw until it snaps firmly
onto the valve push rod. Replace the bottom valve body cap.
Leaking Valves:
To stop a valve from dripping milk start by removing the splash guard (item 10) by hand and the apron (item 12) with a
Phillips screwdriver. Locate and loosen the adjustment nut and bolt shown in the valve cross section on page 3.
Remove the milk tube from the valve. Raise and drop the valve arm (item 34) several times until the valve jaw (item 33)
is tight to the front of the valve opening when the valve arm is fully lowered. Re-tighten the adjustment nut and bolt and
replace the apron and splash guard. Also make sure that the milk tube is cut as close as possible to the valve.
90037
MODEL____________________ SERIAL NO.____________________ DATE INSTALLED____________________
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
9
PUSH ARM
ADJUSTMENT
NUT & BOLT
PARTS LIST - SK5MAJ
ITEM NO. DESCRIPTION PART NO.
1 DOOR ASSEMBLY 63319
2 DOOR GASKET 10310-26
3 THERMOMETER 20361
4 THERMOMETER LENS 22986
5 HINGE KIT (MALE, FEMALE, COVERS & SCREWS) 10327-09
6 HINGE KIT (MALE, FEMALE, COVERS & SCREWS) 10327-09
7 HINGE COVER 21758
8 DOOR STRIKE 21073
9 LATCH 21069
10 SPLASH GUARD 63303
11 GLASS STOP 21074
12 APRON 63367
13 BACK PANEL 63291
14 FRONT LEG 63599
15 REAR LEG 63600
16 DRIP TRAY SUPPORT 43287
17 DRIP TRAY 63374
18 DRIP TRAY COVER 63376
19 LOADING SHELF 63406
20 PIVOT SCREW, LOADING SHELF 23503
21 STOP SCREW, LOADING SHELF 23504
22 POWER CORD 115V 22099
POWER CORD 220V 23514
23 TEMPERATURE CONTROL 43064
24 MILK KRATE 63344
25 GROMMET 20481
26 WASHER 22401
27 HAIRPIN CLIP 98106
28 PUSH ROD 23742
29 HAIRPIN CLIP 23530
30 SPRING, SHUT OFF 23450
31 SPRING, OVERTRAVEL 23496
32 VALVE BODY CAP 23409
33 JAW VALVE 23918
34 VALVE HANDLE 43259
35 COMPRESSOR 115V/60HZ 10343-02
COMPRESSOR 220V/50HZ 10343-33
36 & 37 ELECTRICAL KIT 115V (RELAY & OVERLOAD) 10344-02
ELECTRICAL KIT 230V (RELAY & OVERLOAD) 10344-33
38 HAIRPIN CLIP 23744
39 DRIER 22677
10
WHEN ORDERING REPLACEMENT PARTS, PLEASE PROVIDE MODEL AND SERIAL NUMBERS
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Silver King Majestic SK12MAJ User manual
-
-
-
-
-
-
-
-
-
Other documents
-
SEVERIN SM9669 Datasheet
-
Zanussi TD184-260133215090 User manual
-
Champion Power Equipment 90037 User manual
-
Filter Queen Majestic High-Filtration Surface Cleaner User manual
-
Hobart HCM300-HCM450 Cutter Mixer Installation guide
-
Haier BrewMaster HBF205E User manual
-
-
Redmond RMC-M23A Owner's manual
-
-
The First Years Breastflow Memory Pump Y4947 User manual
