• Unobtrusive Passive Infrared Sensor housing
design
• Horizontal resolution of 330 lines for WV-
CF400 or 380 lines for WV-BF300
• Minimum illumination of 42 lx (4.2 foot-can-
dle) for WV-CF400 or 2.1 lx (0.21 foot-candle)
for WV-BF300
FEATURES
• Signal-to-noise ratio of 46 dB with AGC off
• Exclusive lens is provided
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove
screws or covers.
There are no user serviceable parts inside.
Ask a qualified service person for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be damaged
by improper handling or storage.
3. Do not expose the camera to rain or
moisture, or try to operate it in wet areas.
Turn the power off immediately and ask a
qualified service person for servicing.
Moisture can damage the camera and also
create the danger of electric shock.
4. Do not use strong or abrasive detergents
when cleaning the camera body.
Use a dry cloth to clean the camera when
dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently.
5. Clean the lens with care.
Do not clean the lens with strong or abrasive
detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects.
Whether the camera is in use or not, never
aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where tem-
perature is between –10°C - +50°C (14°F -
122°F), and humidity is below 90 %.
PRECAUTIONS
CCTV Camera
WV-CF400/WV-BF300
Before attempting to connect or operate this product,
please read these instructions carefully.
N0599-2089 YWV8QA5219CN Printed in Japan
N 30
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK), NO USER SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte-
nance (servicing) instructions in the
literature accompanying the appli-
ance.
The lightning flash with arrowhead
symbol, within an equilateral trian-
gle, is interned to alert the user to
the presence of uninsulated "dan-
gerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
The serial number of this product may be found on
the rear of the unit.
You should note the serial number of this unit in the
space provided and retain this instruction as a per-
manent record of your purchase to aid identification
in the event of theft.
Model No.
Serial No.
Wij verklaren als enige aansprakelijke, dat het product waarop
deze verklaring betrekking heeft, voldoet aan de volgende nor-
men of andere normatieve documenten, overeenkomstig de
bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.
Vi erklærer os eneansvarlige for, at dette produkt, som denne
deklaration omhandler, er i overensstemmelse med standarder
eller andre normative dokumenter i følge bestemmelserne i
direktivene 73/23/EEC og 89/336/EEC.
Vi deklarerar härmed värt fulla ansvar för att den produkt till
vilken denna deklaration hänvisar är i överensstämmelse med
standarddokument, eller andra normativa dokument som
framstölls i EEC-direktiv nr. 73/23 och 89/336.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä
ilmoitus koskee, noudattaa seuraavia standardeja tai muita
ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC
ja 89/336/EEC säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne
erklæringen gjelder for, er i overensstemmelse med følgende
normer eller andre normgivende dokumenter som følger
bestemmelsene i direktivene 73/23/EEC og 89/336/EEC.
We declare under our sole responsibility that the product to
which this declaration relates is in conformity with the stan-
dards or other normative documents following the provisions of
Directives EEC/73/23 and EEC/89/336.
Noi dichiariamo sotto nostra esclusiva responsabilità che il
prodotto a cui si riferisce la presente dichiarazione risulta con-
forme ai seguenti standard o altri documenti normativi confor-
mi alle disposizioni delle direttive CEE/73/23 e CEE/89/336.
INSTALLATION
Important Notices:
• The following installation should be made by qualified service personnel or system installers
and should conform to all local codes.
• Be sure to use a wall board having enough strength to support this camera.
• Do not use the camera at a place where it may be exposed to oil splashes.
Oil can cause cracks in the part where the camera is mounted.
Mounting the camera (by leading the cables through a hole in the wall)
To make a hole for the cables in the wall where the camera is to be installed, proceed as follows:
15mm (9/16”)
50mm (2”)
To AC Adapter
To Video Input
3. Pass the cables through the cable hole.
4. Connect the cables as shown in the dia-
gram.
5. Mount the camera onto the wall by fixing it
with the mounting screws.
Note:
To monitor images in upright position,
confirm that the cable outlet is up as
shown in the diagram before fixing the
camera with the screws.
6. Attach the panel cover. Make sure that the
cover is closed firmly and that the camera
wires are not caught.
1. Determine the place on the wall where you
want to install the camera. Then make a
hole (approx. φ15 mm) in the wall referring
to the diagram above.
2. Detach the panel cover by pressing it at
the top and bottom as shown in the dia-
gram.
INSTALLATION OF OPTIONAL LENS
To install the optional lens, follow the procedure shown below.
Cushioning Ring
Lens
1. Detach the cover by pressing it at the top
and bottom as shown in the diagram.
2. Detach the camera by removing the four
screws shown in the diagram.
5. Remove the lens (originally mounted on
the camera) from the camera by turning it
counterclockwise.
6. Remove the lens cap from the optional
lens.
4. Install the camera with the brackets on the
base with two screws.
Caution:
Confirm that the camera is mounted
with the top up.
3. Place the brackets (provided as standard
accessory) on both sides of the camera
and tighten with the two screws.
Side view of the camera
Top
Cushioning Ring
Lens
7. Mount the optional lens onto the camera
by turning it clockwise as shown in the dia-
gram.
Cautions:
• Do not forget to install the cushioning
ring as shown in the diagram.
• Install only one cushioning ring bet-
ween the lens and the camera.
• When the WV-LXY18C4 optional lens
are installed in the WV-BF300 or WV-
CF400 camera, a picture with missing
corners will appear on the monitor
screen as shown below.
Camera
Pick-up Device: 512 (H) x 582 (V) pixels, Interline Transfer CCD
Scanning Area: 3.61 (H) x 2.70 (V) mm (Equivalent to scanning area of 1/4”
pick-up tube)
Scanning System: 2 : 1 interlace
Scanning: 625 lines / 50 fields / 25 frames
Horizontal: 15.625 kHz
Vertical: 50 Hz
Synchronization: Internal
Video Output: 1.0 V[p-p] composite 75 Ω (Standard RCA type pin plug)
Horizontal Resolution: WV-CF400: 330 lines at centre
WV-BF300: 380 lines at centre
Signal-to-Noise Ratio: 46 dB (AGC OFF, weight ON)
Minimum Illumination: WV-CF400: 42 lx (4.2 foot-candle) at F2.8
WV-BF300: 2.1 lx (0.21 foot-candle) at F2.8
Automatic Gain Control (AGC): +15 dB preset
Electronic Light Control (ELC): Equivalent to continuous variable shutter speed between 1/50 s
and 1/96 000 s
White Balance (WV-CF400 only): ATW (Automatic Tracing White Balance) preset
Angular Field of View: Horizontal; 45˚, Vertical; 34˚
Power Requirement: 6 V DC 0.2 A by exclusive AC adapter model A20620GPA
Ambient Operating Temperature: −10°C - +50°C (14°F - +122°F)
Ambient Operating Humidity: Less than 90 %
Dimensions: 70 (W) x 80 (H) x 38 (D) mm
[2-3/4” (W) x 3-1/8” (H) x 1-1/2” (D)]
Weight: 115 g (0.25 lbs.)
AC Adapter
Input: 230 V AC, 50 Hz
Output: 6 V DC, 0.2 A, 1.2 VA
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
Note: Noise may appear in the monitor images when the camera is used under high-temperature
and low-light conditions.
SPECIFICATIONS
STANDARD ACCESSORIES
AC Adapter.......................................................................................1
Bracket..............................................................................................2
OPTIONAL ACCESSORIES
Lenses : WV-LXY18C4E, WV-LXY23C4E, WV-LXY47C4E
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Panasonic WVCF420 Operating instructions
-
-
-
-
-
-
-
-
-