Panasonic WVCF420 Operating instructions

Brand: Panasonic

Model: WVCF420

Category: Security cameras

Type: Operating instructions

• Unobtrusive smoke detector housing design

• Horizontal resolution of 330 lines for WV-

CF420 or 380 lines for WV-BF320

• Minimum illumination of 10 lx (1.0 foot-can-

dle) for WV-CF420 or 0.5 lx (0.05 foot-candle)

for WV-BF320

FEATURES

• Signal-to-noise ratio of 46 dB with AGC off

• Exclusive lens is provided

1. Do not attempt to disassemble the camera.

To prevent electric shock, do not remove

screws or covers.

There are no user serviceable parts inside.

Ask a qualified service person for servicing.

2. Handle the camera with care.

Do not abuse the camera. Avoid striking,

shaking, etc. The camera could be damaged

by improper handling or storage.

3. Do not expose the camera to rain or

moisture, or try to operate it in wet areas.

Turn the power off immediately and ask a

qualified service person for servicing.

Moisture can damage the camera and also

create the danger of electric shock.

4. Do not use strong or abrasive detergents

when cleaning the camera body.

Use a dry cloth to clean the camera when

dirty.

In case the dirt is hard to remove, use a mild

detergent and wipe gently.

5. Clean the lens with care.

Do not clean the lens with strong or abrasive

detergents. Use lens tissue or a cotton tipped

applicator and ethanol.

6. Never face the camera towards the sun.

Do not aim the camera at bright objects.

Whether the camera is in use or not, never

aim it at the sun or other extremely bright

objects. Otherwise, blooming or smear may

be caused.

7. Do not operate the camera beyond the

specified temperature, humidity or power

source ratings.

Use the camera under conditions where tem-

perature is between –10°C - +50°C (14°F -

122°F), and humidity is below 90 %.

PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK), NO USER SERVICEABLE PARTS

INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and mainte-

nance (servicing) instructions in the

literature accompanying the appli-

ance.

The lightning flash with arrowhead

symbol, within an equilateral trian-

gle, is interned to alert the user to

the presence of uninsulated "dan-

gerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

WARNING:

TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

The serial number of this product may be found on

the top of the unit.

You should note the serial number of this unit in the

space provided and retain this instruction as a per-

manent record of your purchase to aid identification

in the event of theft.

Model No.

Serial No.

CCTV Camera

WV-CF420/WV-BF320

Before attempting to connect or operate this product,

please read these instructions carefully.

N0599-2089 YWV8QA5220CN Printed in Japan

N 30

Wij verklaren als enige aansprakelijke, dat het product waarop

deze verklaring betrekking heeft, voldoet aan de volgende nor-

men of andere normatieve documenten, overeenkomstig de

bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.

Vi erklærer os eneansvarlige for, at dette produkt, som denne

deklaration omhandler, er i overensstemmelse med standarder

eller andre normative dokumenter i følge bestemmelserne i

direktivene 73/23/EEC og 89/336/EEC.

Vi deklarerar härmed värt fulla ansvar för att den produkt till

vilken denna deklaration hänvisar är i överensstämmelse med

standarddokument, eller andra normativa dokument som

framstölls i EEC-direktiv nr. 73/23 och 89/336.

Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä

ilmoitus koskee, noudattaa seuraavia standardeja tai muita

ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC

ja 89/336/EEC säädöksiä.

Vi erklærer oss alene ansvarlige for at produktet som denne

erklæringen gjelder for, er i overensstemmelse med følgende

normer eller andre normgivende dokumenter som følger

bestemmelsene i direktivene 73/23/EEC og 89/336/EEC.

We declare under our sole responsibility that the product to

which this declaration relates is in conformity with the stan-

dards or other normative documents following the provisions of

Directives EEC/73/23 and EEC/89/336.

Noi dichiariamo sotto nostra esclusiva responsabilità che il

prodotto a cui si riferisce la presente dichiarazione risulta con-

forme ai seguenti standard o altri documenti normativi confor-

mi alle disposizioni delle direttive CEE/73/23 e CEE/89/336.

80 mm (3-1/8

”)

80 mm (3-1/8

”)

15 mm (9/16”)

Arrow Mark for

upright positioning

of image

INSTALLATION

To AC Adapter

To Video Input

Arrow mark

Important Notices:

• The following installation should be made

by qualified service personnel or system

installers and should conform to all local

codes.

• Be sure to use a ceiling board having

enough strength to support this camera.

• Do not use the camera at a place where it

may be exposed to oil splashes.

Oil can cause cracks in the part where the

camera is mounted.

Mounting the camera (by leading the cables

through a hole in the ceiling)

To make a hole for the cables in the ceiling

where the camera is to be installed, proceed

as follows:

1. Determine the place on the ceiling where

you want to install the camera. Then make

a hole (approx. φ15 mm) in the ceiling

referring to the diagram at right.

2. Detach the panel cover by rotating it coun-

terclockwise.

3. Pass the cables through the cable hole.

4. Connect the cables as shown in the dia-

gram.

5. Mount the camera onto the ceiling by fix-

ing it with the mounting screws.

Note: The arrow mark on the camera’s

base plate indicates the direction of

the camera and coincides with the top

of the image displayed on the monitor.

To monitor images in upright position,

confirm that the arrow mark points in

the right direction before fixing the

camera with the screws.

6. Attach the panel cover to match the

“Panasonic” logo and arrow mark, and

rotate the cover clockwise. Make sure the

panel cover is closed firmly.

3. Tilt the camera in the direction of the Arrow

Mark until the protrusions on the camera fit

into the grooves in the upper portion of

the screw hole.

If the camera is difficult to tilt, slightly bend

open the bracket on both sides.

4. Tighten camera and bracket with the two

screws.

5. Detach the camera with the bracket from

the base plate by removing the two screws

to change the camera position.

6. Move the camera with the bracket to the

position on the base plate as shown in the

diagram and tighten it with the two screws.

Caution: Confirm that the direction of the

camera shown in the diagram coin-

cides with the top of the image dis-

played on the monitor screen.

Tilt the camera until protrusions

of the camera fit into these

grooves in the screw hole.

This camera can pick up images through the

holes on both sides of the panel cover. This

requires moving the position of the camera.

To pick up images through the hole above, fol-

low the procedure shown below.

1. Detach the panel cover by rotating it coun-

terclockwise.

2. Remove the two screws holding the cam-

era shown in the diagram.

■ CHANGING OF CAMERA INSTALLATION POSITION

Arrow mark

Top of screen image

Camera

Pick-up Device: 512 (H) x 582 (V) pixels, Interline Transfer CCD

Scanning Area: 3.61 (H) x 2.70 (V) mm (Equivalent to scanning area of 1/4”

pick-up tube)

Scanning System: 2 : 1 interlace

Scanning: 625 lines / 50 fields / 25 frames

Horizontal: 15.625 kHz

Vertical: 50 Hz

Synchronization: Internal

Video Output: 1.0 V[p-p] composite 75 Ω (Standard RCA type pin plug)

Horizontal Resolution: WV-CF420: 330 lines at centre

WV-BF320: 380 lines at centre

Signal-to-Noise Ratio: 46 dB (AGC OFF, weight ON)

Minimum Illumination: WV-CF420: 10 lx (1.0 foot-candle) at F2.8

WV-BF320: 0.5 lx (0.05 foot-candle) at F2.8

Automatic Gain Control (AGC): +15 dB preset

Electronic Light Control (ELC): Equivalent to continuous variable shutter speed between

1/50 s and 1/96 000 s

White Balance (WV-CF420 only): ATW (Automatic Tracing White Balance) preset

Angular Field of View: Horizontal; 45˚, Vertical; 34˚

Power Requirement: 6 V DC 0.2 A by exclusive AC adapter model A20620GPA

Ambient Operating Temperature: −10°C - +50°C (14°F - 122°F)

Ambient Operating Humidity: Less than 90 %

Dimensions: φ129 x 46.5 mm [φ5-1/16” x 1-13/16”]

Weight: 160 g [0.35 lbs]

AC Adapter

Input: 230 V AC 50 Hz

Output: 6 V DC, 0.2 A, 1.2 VA

Weights and dimensions indicated are approximate.

Specifications are subject to change without notice.

Note: Noise may appear in the monitor images when the camera is used under high-temperature

and low-light conditions.

STANDARD ACCESSORY

AC Adapter.......................................................................................1

SPECIFICATIONS

Matsushita Electric Industrial Co., Ltd.

Central P.O. Box 288, Osaka 530-91, Japan

Panasonic WVCF420 Operating instructions

Brand: Panasonic

Model: WVCF420

Category: Security cameras

Type: Operating instructions

Download PDF

report

in other languages

dansk: Panasonic WVCF420 Betjeningsvejledning

Panasonic WVCF420 Operating instructions

Panasonic WVCF420 Operating instructions

in other languages

Related papers

Other documents