IBM ARTIC960RxD User manual

IBM

IBM ARTIC960RxD Quad Digital Trunk

PCI Adapter

Installation and User's Guide

Second Edition (March, 1999)

The following paragraph does not apply to the United Kingdom or any country where

such provisions are inconsistent with local law: THIS PUBLICATION IS PROVIDED “AS

IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied

warranties in certain transactions, therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are

periodically made to the information herein; these changes will be incorporated in new editions

of the publication. The manufacturer may make improvements and/or changes in the

product(s) and/or the program(s) described in this publication at any time, without notice.

It is possible that this publication may contain reference to, or information about, products

(machines and programs), programming, or services that are not announced in your country.

Such references or information must not be construed to mean that these products,

programming, or services will be announced in your country. Any reference to a specific

licensed program in this publication is not intended to state or imply that you can use only that

licensed program. You can use any functionally equivalent program instead.

Requests for technical information about products should be made to your authorized reseller

or marketing representative.

Note to U.S. Government Users -- Documentation related to restricted rights -- Use,

duplication or disclosure is subject to restrictions set forth is GSA ADP Schedule Contract with

IBM Corp.

Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Handling Static Sensitive Devices ........................... vii

About This Book ...................................... ix

ISO 9000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Related Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

IBM ARTIC960 Run Time Enviornment (RTE) Version 1.3 (or later) Support for

AIX Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Jumper Installation Information ............................. 1-3

Installing the IBM ARTIC960RxD Quad Digital Trunk PCI Adapter ......... 1-4

Operating System Support ................................ 1-9

Chapter 2. Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Features and Function .................................. 2-2

Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Optional Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Operating System Support Programs and Publications ............... 2-5

Chapter 3. Removing and Reinstalling the Quad T1/E1 DTA .......... 3-1

Removing the Quad T1/E1 DTA ............................. 3-1

Reinstalling the Quad T1/E1 DTA ............................ 3-2

Chapter 4. Installing the Device Driver on the RS/6000 SP System ..... 4-1

Check System Pre-Requisites .............................. 4-1

Install Software on the Control Workstation ...................... 4-4

Chapter 5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Problem Determination Procedures ........................... 5-1

Diagnostic Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Diagnostic Wrap Plugs .................................. 5-2

Chapter 6. Cables and Connectors ......................... 6-1

Port Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Connector Pin Numbers and Assignments ....................... 6-4

Contents iii

Appendix A. Communications Statements . . . . . . . . . . . . . . . . . . . . . A-1

Federal Communications Commission (FCC) Statement .............. A-1

European Union (EU) Statement ............................ A-1

International Electrotechnical Commission (IEC) Statement ............. A-2

United Kingdom Telecommunications Safety Requirements ............. A-2

Avis de conformité aux normes du ministère des Communications du Canada . A-2

Canadian Department of Communications Compliance Statement ......... A-2

VCCI Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Electromagnetic Interference (EMI) Statement - Taiwan ............... A-3

Radio Protection for Germany .............................. A-4

Telecommunications Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-1

Reader's Comments — We'd Like to Hear From You ............... X-3

iv Installation and User's Guide

Safety Information

DANGER

An electrical outlet that is not correctly wired could place hazardous

voltage on metal parts of the system or the devices that attach to the

system. It is the responsibility of the customer to ensure that the outlet

is correctly wired and grounded to prevent an electrical shock.

Before installing or removing signal cables, ensure that the power

cables for the system unit and all attached devices are unplugged.

When adding or removing any additional devices to or from the system,

ensure that the power cables for those devices are unplugged before

the signal cables are connected. If possible, disconnect all power

cables from the existing system before you add a device.

Use one hand, when possible, to connect or disconnect signal cables

to prevent a possible shock from touching two surfaces with different

electrical potentials.

During an electrical storm, do not connect cables for display stations,

printers, telephones, or station protectors for communication lines.

Safety Information v

vi Installation and User's Guide

Handling Static Sensitive Devices

Attention: Static electricity can damage this device and your system unit. To avoid

damage, keep this device in its static protective bag until you are ready to install it.

To reduce the possibility of electrostatic discharge, follow the precautions listed

below:

 Limit your movement. Movement can cause static electricity to build up around

you.

 Handle the device carefully, holding it by its edges or its frame.

 Do not touch solder joints, pins, or exposed printed circuitry.

 Do not leave the device where others can handle and possibly damage the

device.

 While the device is still in its anti-static package, touch it to an unpainted metal

part of the system unit for at least two seconds. (This drains static electricity

from the package and from your body.)

 Remove the device from its package and install it directly into your system unit

without setting it down. If it is necessary to set the device down, place it on its

static-protective package. (If your device is an adapter, place it component-side

up.) Do not place the device on your system unit cover or on a metal table.

 Take additional care when handling devices during cold weather, as heating

reduces indoor humidity and increases static electricity.

Preface vii

viii Installation and User's Guide

About This Book

This book describes the IBM ARTIC960RxD Quad Digital Trunk PCI Adapter. Use

this information along with your system unit documentation to help install the adapter

and device driver software.

Terminology Note

Throughout this book, the IBM ARTIC960RxD Quad Digital Trunk PCI Adapter is

referred to as the

IBM ARTIC960RxD Quad DTA

, the Quad T1/E1 DTA is

referred to as the

mezzanine card

, and the IBM ARTIC960RxD PCI Adapter is

referred to as the

base adapter

.

ISO 9000

ISO 9000 registered quality systems were used in the development and

manufacturing of this product.

Related Information

This book refers to documentation that came with your system unit.

Trademarks

AIX, RS/6000 and IBM are registered trademarks of International Business Machines

Corporation.

Other company, product, and service names may be trademarks or service marks of

others.

About This Book ix

x Installation and User's Guide

Chapter 1. Installation

Each IBM ARTIC960RxD Quad DTA package includes the following:

 The IBM ARTIC960RxD PCI Adapter and Quad T1/E1 DTA pair

 This book (with Warranty Statement)

Note: The IBM ARTIC960RxD Quad DTA is a Class A device.

The Federal Communications Commission (FCC) classification for this

product might differ from the FCC classification for your system unit. Use the

classification that is highest. For example, if the FCC classification for your

system unit is Class B and a card that you install is Class A, the classification

of your system unit would change to Class A.

Hardware Requirements

The IBM ARTIC960RxD Quad DTA requires a 32-bit, PCI slot. It can be installed in

any PCI-compliant computer with a fixed frequency PCI bus clock, Not

spread-spectrum.

Chapter 1. Installation 1-1

IBM ARTIC960 Run Time Enviornment (RTE) Version 1.3 (or later)

Support for AIX Installation

The IBM ARTIC960 Run Time Enviornment (RTE) Version 1.3 (or later) Support for

AIX must be installed on your system for the IBM ARTIC960RxD Quad DTA to

function. This software is provided on the CD-ROM that came with this product. If

your system is currently on, you may install the device drivers now. If your system is

currently off, you may install the device drivers after installing the adapters.

Note: If you are using the RxD with the IBM DirectTalk for AIX (DT/AIX) software,

the IBM ARTIC960 Run Time Environment (RTE) software (including the device

drivers and RxD support) is installed automatically as part of the DirectTalk for AIX

install process. Refer to the DT/AIX installation guide for further information.

To install the IBM ARTIC960 RTE Version 1.3 Support for AIX:

1. Turn on your system unit.

2. Log in as root.

3. Insert the CD-ROM into the CD-ROM drive.

4. At the command line, type smitty devinst and press Enter.

5. Press F4.

6. Select the CD-ROM option and press Enter.

Note: The installation will start. The message OK will display when the

installation is completed.

7. If you are ready to install the adapter at this time:

a. Type shutdown -F and press Enter to shutdown your system.

b. Skip to “Jumper Installation Information” on page 1-3.

8. If you have already installed the adapter cards:

a. Type shutdown -Fr and press Enter to reboot your system.

b. Log in again as root. The adapters should now be configured and the

system should be ready for use.

1-2 Installation and User's Guide

Jumper Installation Information

Before installing this adapter, set jumper JP01 as follows:

Table 1-1. Jumper Installation Information

Jumper Positions Condition

If the adapter to be installed is connected to either end of the H.100

Cable (see the illustration on page 1-5), the jumper must be installed

as shown in the illustration to the left.

If the adapter to be installed is the only IBM ARTIC960RxD in the

system, then set the jumper as shown in the illustration to the left.

This is the factory setting.

If the adapter to be installed is NOT connected to either end of the

H.100 Cable (see the illustration on page 1-5), then set the jumper as

shown in the illustration to the left.

Chapter 1. Installation 1-3

Installing the IBM ARTIC960RxD Quad Digital Trunk PCI Adapter

The following procedure describes how to install the IBM ARTIC960RxD Quad DTA

into the system unit. The steps may vary depending on your system unit. Refer to

the documentation that came with your system unit for detailed instructions on

performing the following procedures:

Note: Insure that the jumpers are set as described in “Jumper Installation

Information” on page 1-3

 Be sure to perform necessary shutdown procedures to protect your system and

data.

 Shut down your system unit

 Remove the system unit covers

 Install the IBM ARTIC960RxD Quad DTA into your system unit

 Install the H.100 cable if necessary

 Replace the system unit covers

1-4 Installation and User's Guide

IBM ARTIC960RxD Quad Digital Trunk PCI Adapter Internal Cabling

Multi-drop cable assemblies are used to connect the internal busses on up to four

Quad Digital Trunk PCI Adapters. There are three top card cables, RW, RX and RY.

RW is used to connect multiple IBM ARTIC960RxD Quad DTAs to each other as well

as other adapters with H.100 connectors, see below. Cables RX and RY are used to

connect Quad DTAs or other adapters that have H.100 connectors as well as

adapters that have SC-Bus connectors, see the following two pages.

These cables are just long enough to connect four adapters that support H.100

connectors in adjacent slots.

H.100, 4-Drop Cabling: The IBM ARTIC960RxD Quad DTAs have H.100 top

card connectors.

The following figure illustrates the internal cabling for the IBM ARTIC960RxD Quad

DTAs with the H.100 top card connectors cabled together. Up to four IBM

ARTIC960RxD Quad DTAs are supported and must be in adjacent slots. Refer to

Table 1-1 on page 1-3 to position the jumper on JP01 on the base card.

H.100, 4-Drop Ribbon Cabling

RW

Table 1-2. H.100, 4-drop Internal Cable Information

Cable

Letter

Cable Name/ Description Part

Number

Feature

Code

Length

m ft

RW H.100, 4-drop Internal Cable 08L1215 2877 0.127 0.417

Chapter 1. Installation 1-5

SC-Bus, 5-Drop Cable: This Multi-drop cable assembly is used to connect up to

four adapters with SC-Bus internal connectors. It has an additional SC-Bus

connector which connects to cable RY. See “H.100, 4-Drop Cable With SC-Bus

Converter Connector” on page 1-7. This allows adapters with SC-Bus connectors to

be used with the IBM ARTIC960RxD Quad DTAs and with other adapters that have

H.100 top card connectors.

The following figure illustrates the internal cabling for up to four adapters with

SC-Busses and an additional SC-Bus connector which goes to the H.100 4-drop

Cable with SC-Bus converter connector. Refer to Table 1-1 on page 1-3 to position

the jumper on JP01 on the base card.

SC-Bus, 5-Drop Cable

SC-Bus

to H.100 Bus

with SC-Bus

Converter

Connector

RX

Table 1-3. SC-Bus, 5-Drop Cable Information

Cable

Letter

Cable Name/ Description Part

Number

Feature

Code

Length

m ft

RX SC-Bus, 5-Drop Cable 08L1217 2878 0.176 0.58

1-6 Installation and User's Guide

H.100, 4-Drop Cable With SC-Bus Converter Connector: This Multi-drop

cable assembly is used to connect the internal busses on up to four IBM

ARTIC960RxD Quad DTAs with H.100 connectors. It has an additional connector to

connect to cable RX. See “SC-Bus, 5-Drop Cable” on page 1-6. This allows

adapters with SC-Bus connectors to be used with the IBM ARTIC960RxD PCI

Adapters and other adapters that have H.100 connectors.

The following figure illustrates the internal cabling for up to four IBM ARTIC960RxD

Quad DTAs with an additional connector to the SC-Bus 5-drop cable with SC-Bus

converter connector. Refer to Table 1-1 on page 1-3 to position the jumper on

JP01 on the base card.

H.100, 4-Drop cable with SC-Bus Converter Connector

SC-Bus

Converter

Connector

RY

Table 1-4. H.100, 4-Drop Cable with SC-Bus Converter Connector Cable Information

Cable

Letter

Cable Name/ Description Part

Number

Feature

Code

Length

m ft

RY H.100, 4-Drop Cable with SC-Bus

Converter Connector

08L1219 2879 0.176 0.58

Note: This cable is referred to as the Four-drop, H.100 Cable with SC-Bus

Converter in other publications associated with this cable.

Chapter 1. Installation 1-7

Connecting Telecommunications Cables

Attention

Do not connect or handle the cable during a lightning storm.

The following instructions assume that you have the adapter in the system unit and

are ready to attach an Telecommunications Cables.

1. Align the 36-pin connector of the cable with the 36-pin connector at the rear of

the IBM ARTIC960RxD Quad DTA.

2. Depress the latch buttons on either side of the cable connector and firmly press

the cable connector into the 36-pin connector.

3. Release the latch buttons and make sure that the cable connector latches are

securely seated.

If required, connect a lightning protection device to the other ends of the cable.

Refer to the instructions that came with the device.

At the very least, the grounding strap on the lightning protection device should be

connected to an earth-ground on or near the computer.

4. Connect one or more of the four ports of the optional cable to the target device.

Each connector is marked with its port number.

Telecommunications ports are numbered 0,1,2 and 3 whereas some software (such

as DirectTalk/AIX) refers to the ports as 'Trunks 1,2,3 and 4'.

Note: Moving the system unit with a cable attached can dislodge an adapter. If any

adapter or card becomes dislodged while power is applied, proceed as

follows:

1. Turn off the computer and unplug all power cords.

2. Remove the system unit cover.

3. Loosen the expansion-slot screw of the dislodged adapter. Press down

on the top edge of the adapter to reseat it. Then, re-tighten the

expansion-slot screw.

4. Reinstall the system unit cover and replug power cords.

5. Turn on the computer.

1-8 Installation and User's Guide

Operating System Support

If the DirectTalk for AIX software is used, the IBM ARTIC960 RTE is automatically

installed as part of the DirectTalk for AIX installation. Proceed to Chapter 2.

Downloading the Operating System Support Programs and Diagnostics

The adapter diagnostic program and the support programs for AIX can be obtained

through the World Wide Web or a Bulletin Board System (BBS).

The IBM ARTIC960 Run Time Enviornment (RTE) Version 1.3 (or later) Support for

AIX is shipped with the adapter.

Downloading from the Web: Do the following.

1. Using a Web browser of your choice, type:

http://wwprodsoln.bocaraton.ibm.com/artic/file_rep.html

2. Select the operating-system support you want.

3. Download the Program file.

4. Download the Installation/file creation instructions file, and follow the steps for

installing and configuring the product support.

Chapter 1. Installation 1-9

Downloading from the BBS: Do the following.

1. Check that your modem settings are as follows:

Data Bit 8

Parity Bit N

Stop Bit 1

2. Dial the U.S.A. number 561-443-8222.

3. Select the operating system support you want.

4. Select a Transfer Protocol supported by your communications software.

5. View on-line or download the Readme/Instruction file.

6. Follow the instructions in the readme file for downloading and installing the

program support that comes with the diagnostics.

Obtaining Operating System Software when Web/BBS Support Is

Unavailable: For those who are unable to retrieve the files from either the Web or

BBS, support is provided by telephone or E-mail.

For telephone assistance (U.S.A. ONLY), call:

1-800-426-4968 and ask for technical support for the IBM ARTIC960.

For E-mail assistance, send to:

[email protected]

1-10 Installation and User's Guide

Page is loading ...

IBM ARTIC960RxD User manual

This manual is also suitable for

IBM ARTIC960RxD User manual

Related papers

Other documents