Whirlpool ARZ 8970/H User guide

ARZ 8970/H
Whirlpool
Brand
Whirlpool
Model
ARZ 8970/H
Category
Fridge-freezers
Type
User guide
66
GB CONTENTS
.
BEFORE USING THE REFRIGERATOR
PAGE
67
SAFEGUARDING THE ENVIRONMENT
PAGE
67
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
PAGE
68
HOW TO OPERATE THE REFRIGERATOR
COMPARTMENT
PAGE
69
HOW TO OPERATE THE FREEZER COMPARTMENT
PAGE
69
HOW TO DEFROST THE FREEZER COMPARTMENT
PAGE
71
CARE AND MAINTENANCE
PAGE
72
TROUBLESHOOTING GUIDE
PAGE
73
AFTER-SALES SERVICE
PAGE
73
INSTALLATION
PAGE
74
ELECTRICAL CONNECTION
PAGE
75
33124Gb.fm5 Page 66 Wednesday, February 23, 2000 9:03 AM
67
Your new appliance is a combined fridge-freezer
exclusively for domestic use.
The freezer compartment can be
used for freezing fresh and cooked food, making
ice cubes, and storing frozen and deep-frozen
food; defrosting is a manual procedure. The
refrigerator compartment, which has an
automatic defrost feature, is used for the
storage of fresh food and beverages.
To get the most out of your new appliance,
read the user handbook thoroughly. The
handbook contains a description of the
appliance and useful tips for storing food.
Keep this handbook for future consultation.
1. After unpacking the appliance, make sure
that the doors shut properly. Any damage
must be reported to your dealer within 24
hours after delivery of the appliance.
2. Wait at least two hours without moving
the appliance before switching on. This
will give the refrigerant circuit time to
settle and operate efficiently.
3. Installation of the appliance and electrical
connections must be carried out by a
qualified electrician, in accordance with the
manufacturer’s instructions and local
regulations.
1. Packing
The packaging material is entirely recyclable,
and marked with the recycling symbol.
Follow local regulations for scrapping.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
2. Appliance
The appliance is made using recyclable
materials. Dispose of the appliance in conformity
with local environmental regulations.
Make the appliance unusable by cutting off the
power cord. The appliance must be delivered to
an authorised collection centre for the recovery
of refrigerant gas.
Information:
This appliance does not contain CFCs
(replaced with R134a) or HFCs (replaced with
R600a - Isobutane). For more information, refer
to the identification data plate affixed to the
appliance.
BEFORE USING THE REFRIGERATOR
SAFEGUARDING THE ENVIRONMENT
33124Gb.fm5 Page 67 Wednesday, February 23, 2000 9:03 AM
68
• Use the refrigerator compartment only for
storing fresh food and beverages and use the
freezer compartment only for storing frozen
food, freezing fresh food and making ice
cubes.
• Do not cover or obstruct the air vents of the
appliance.
• Do not store liquids in glass containers in the
freezer compartment - danger of bursting.
• Do not eat ice cubes or ice lollies immediately
after taking them out of the freezer
compartment - risk of “cold” burns.
• Do not allow children to play or hide inside
the appliance - risk of becoming trapped and
suffocating.
• Do not ingest the contents (non-toxic) of the
ice packs (if provided).
• Before servicing or cleaning the
appliance, unplug it from the mains or
disconnect the electrical power supply.
• The power cable may only be replaced by an
authorised person.
• After installation, make sure that
therefrigerator is not standing on the power
supply cable.
Declaration of conformity
• This appliance is intended to come into
contact with foodstuffs and conforms to
D.L. 108 of 25.01.1992 (European
Directive 89/109/EEC).
Information
Appliances with Isobutane (R600a)
Isobutane is a natural gas having low
environmental impact. Caution is required,
however, since isobutane is flammable.
Therefore, it is essential to ensure that
refrigerant pipelines are not damaged.
Defrosting of the refrigerator compartment is
completely automatic.
The refrigerator can operate at ambient
temperature between +10° C and +38° C.
Optimal performance is obtained at
temperatures between +16° C and +32° C.
Switching on the appliance
• Turn the selector (1) to the position shown on
the product description sheet (recommended
by the Manufacturer).
• Green LED (3) lights up, indicating operation
of the refrigerator compartment. In models
with one compressor only, also turn the knob
to switch on the appliance (4).
• Turn the knob (1) to Off to switch off the
refrigerator compartment.
• To switch the light off when the door is open,
pull the switch (8).
SUPERCOOL FUNCTION/TURBOCOOL
• In order to cool food rapidly, press the button
(2): green LED (3) will become yellow and
remain so throughout this function. To cancel
the operation, press the button again.
Important:
• After being switched on, the refrigerator
needs approximately 30 minutes to reach the
correct temperature to store a typical volume
of food in the refrigerator compartment.
.
CLEANING FUNCTION
• By turning the knob (1) to Off it is possible to
clean and empty the refrigerator
compartment with the light on. Pull the switch
(8) to switch the light off.
PRECAUTIONS AND GENERAL RECOMMENDATIONS
HOW TO OPERATE THE REFRIGERATOR
COMPARTMENT
33124Gb.fm5 Page 68 Wednesday, February 23, 2000 9:03 AM
69
To adjust the temperature, follow the
instructions in the accompanying chart.
To switch off the refrigerator
compartment:
•
Turn the knob (1) to Off.
•
Pull the light switch (8) if you wish to leave the
door open.
Using the refrigerator compartment
Position the food as shown in the figure.
A Cooked food
B Fish, meat
C Fruit and vegetables
D Bottles
E Butter
F Dairy products, cheese
Notes:
•
The space between the shelves and the rear
wall of the refrigerator compartment must be
unobstructed to allow circulation of air.
•
Do not place food in direct contact with the rear
wall of the refrigerator compartment.
•
Do not place hot food in the refrigerator or
freezer.
•
Store liquids in closed containers.
•
Storing vegetables with a high water content
can result in condensation in the crisper
drawer: this will not affect the correct
operation of the appliance.
•
Turn the temperature selector (4) to the position
shown on the product description sheet.
•
The
red LED
(9) remains lit (for about 1
hour), until the critical alarm temperature is
reached. The red LED lights up when:
-
the appliance is connected to the power
supply for the first time;
-
the door of the freezer is open too long;
-
the quantity of food loaded into the
freezer exceeds that indicated on the
data plate;
-
the freezer compartment temperature is
too high.
•
The
green LED
(7) lights up when the freezer
compartment is operating.
•
After switching on, the freezer compartment
takes approximately 3 hours to reach a
suitable temperature for frozen food storage.
To adjust the temperature, follow the
instructions in the accompanying chart.
To switch off the freezer compartment
(and the refrigerator compartment in the
models with 1 compressor):
Turn the knob (4) to Off.
How to freeze fresh food
You can use the freezer compartment
to freeze food.
The amount of fresh food that can be frozen
in 24 hours, at an ambient temperature
of +25°C, is indicated on the data plate.
HOW TO OPERATE THE REFRIGERATOR COMPARTMENT
HOW TO OPERATE THE FREEZER COMPARTMENT
33124Gb.fm5 Page 69 Wednesday, February 23, 2000 9:03 AM
70
How to operate:
• 24 hours before freezing fresh food, press
the fast freeze button (6). The freezer
compartment operation LED (7) turns from
green to yellow and remains so throughout
this function (24 h).
• Wrap and seal the food in: aluminium foil,
cling film, watertight plastic bags, polythene
containers with lids or special freezer
containers.
• Place food in the top compartment, leaving
enough space for air to circulate around
packs. To speed up the freezing process and
increase the compartment capacity remove
the top basket and the ice pack storage
drawer (if provided). Put the already frozen
food into the other drawers and the food still
to be frozen directly onto the refrigerator grid.
For more efficient freezing, use the fast freeze
function for the next 24 hours by pressing the
button (6) again when the yellow LED (7)
turns back to green.
ECO/ÖKO FUNCTION
• When the freezer is only partially full and the
food is already frozen, set the knob (4) to
“Eco/öko” for energy saving.
Note:
• In the event of a power failure, the freezer
compartment maintains the correct storage
temperature for about 16 hours.
• In models with one or two ice packs, this
temperature can be maintained for about
25/30 hours.
• Do not open the freezer compartment door
during a power failure.
Important:
The table alongside shows the recommended
maximum storage time for frozen fresh foods.
When purchasing frozen food products:
• Ensure that the packaging is not damaged
(frozen food in damaged packaging may
have deteriorated). If the package is swollen
or has damp patches, it may not have been
stored under optimal conditions and
defreezing may have already begun.
• When shopping, leave frozen food
purchases until last and transport the
products in a thermally insulated cool bag.
• Place the items in the freezer compartment
as soon as you get home.
• If food has defrozen even partially, do not re-
freeze it. Consume within 24 hours.
• Avoid, or reduce temperature variations to
the minimum.
• Respect the best-before date on the package.
• Always observe the storage information on
the package.
HOW TO OPERATE THE FREEZER COMPARTMENT
MONTHS FOOD
33124Gb.fm5 Page 70 Wednesday, February 23, 2000 9:03 AM
71
Making ice cubes
•
Fill the ice cube tray 3/4 with water and place
it at the bottom of the freezer compartment.
To speed up the ice making process, place
the tray on the bottom of the first drawer (as
shown in the figure) and not on the ice pack
rack (if provided).
•
If the tray sticks to the bottom of the
compartment, do not use pointed or sharp
instruments to free it.
.
Defrost the freezer compartment once or
twice a year, or when the ice on the walls
reaches a thickness of about 3 mm. If
possible, defrost the freezer compartment
when it is nearly empty.
•
24 hours before defrosting, press the fast
freeze button (6); the LED (7) turns from
green to yellow. This brings the foods to the
lowest possible temperature.
•
Remove the food from the freezer
compartment, wrap in a newspaper and
group together in a cool place or in a portable
cooler.
•
Disconnect the appliance from the mains
power supply.
•
Remove the ice-cube tray.
•
Remove the baskets.
•
Pull out the defrost water drain from the base
of the freezer compartment.
•
Leave the freezer compartment door open.
Place the lower basket, which has a hole in
the rear part, under the drain to collect the
defrost water.
Note: Do not use sharp or pointed metal
instruments to scrape off ice; do not heat the
freezer compartment artificially. Any damage
to the appliance resulting from failure to
observe these instructions is not covered by
the guarantee.
•
Clean the freezer compartment using a sponge
dampened in a solution of warm water and
neutral detergent. Do not use abrasive products.
•
Rinse the interior and dry thoroughly.
•
Reconnect the appliance to the power supply.
•
Refit the drain in place and reposition the
baskets.
•
Before putting the food back in the freezer
compartment, press the fast freeze button
(6). The green LED (7) turns to yellow.
Note:
The increase in temperature of frozen food
during defrosting can shorten its storage life.
HOW TO OPERATE THE FREEZER COMPARTMENT
HOW TO DEFROST THE FREEZER COMPARTMENT
33124Gb.fm5 Page 71 Wednesday, February 23, 2000 9:03 AM
72
Before carrying out any cleaning operations,
unplug the appliance.
• Clean the inside of the freezer compartment
when defrosting.
• Periodically clean the inside of the
refrigerator compartment with a sponge
dampened in warm water and/or neutral
detergent. Rinse the interior and dry with a
soft cloth. Do not use abrasive products.
• Clean the outside with a damp cloth. Do not
use abrasive products, scourers,
stain-removers (e.g. thrichlorethylene
acetone) or vinegar.
• Defrosting of the refrigerator compartment is
completely automatic. Some models are
provided with a drain hole. Clean the defrost
water drain outlet regularly using the tool
supplied with the appliance. This precaution
ensures that defrost water is removed
correctly.
• Periodically clean the condenser
(radiator) at the rear of the appliance and
the plinth with a vacuum cleaner or brush.
Prolonged disuse
1. Empty the refrigerator and freezer
compartments.
2. Disconnect the appliance from the power
supply.
3. Defrost the freezer compartment, and clean
and dry both compartments.
4. Leave the doors open to prevent formation of
unpleasant odours.
CARE AND MAINTENANCE
33124Gb.fm5 Page 72 Wednesday, February 23, 2000 9:03 AM
73
1. The appliance is not working.
• Is there a power failure?
• Is the plug properly inserted in the socket?
• Is the double-pole switch on?
• Has the fuse blown?
• Is the power cord in perfect condition?
• Are the thermostat knobs set to OFF?
2. Temperature inside the compartments is
not low enough.
• Are the doors closed properly?
• Is the appliance installed near a heat source?
• Is the thermostat set correctly?
• Are the air circulation grilles blocked?
• Is the condenser clean?
3. Temperature inside the refrigerator
compartment is too low.
• Is the thermostat set correctly?
4. Water collects at the bottom of the
refrigerator compartment.
• Is the defrost water drain blocked?
• Is the thermostat set correctly?
5. The appliance is excessively noisy.
• Is the appliance in contact with other
furniture or objects?
• Are the pipes at the back touching or vibrating?
• Has the compressor locking pin been
eliminated?
6. The inside light is not working.
Perform the checks for problem 1, and then:
• Disconnect the appliance from the mains
power supply.
• Remove the bulb cover.
• Check the bulb and if necessary replace it.
Replace using maximum 15W bulb.
N.B.: This product uses a special bulb; to
replace do not unscrew. Pull towards the
inside of the appliance.
7. The red LED remains lit.
See: “How to operate the freezer compartment”.
Notes:
• The front edge of the appliance may be
hot. This prevents the formation of
condensation and is not a defect.
• Gurgling and hissing noises due to
expansion in the refrigerant circuit are
normal.
Before contacting After-Sales Service:
1. See if you can solve the problem yourself with
the help of the Trouble-shooting guide.
2. Switch the appliance on again to see if the
problem has been solved. If it has not,
disconnect the appliance from the power
supply and wait for about an hour before
switching on again.
3. If the problem persists after this course of
action, contact After-sales Service.
Specify:
• the nature of the problem,
• the model,
• the Service number (the number after the
word SERVICE on the data plate on the
inside of the appliance),
• your full address,
• your telephone number and area code.
Note:
The direction of door opening can be
changed. If this operation is performed by
After-sales Service it is not covered by the
warranty.
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
33124Gb.fm5 Page 73 Wednesday, February 23, 2000 9:03 AM
74
• Install the appliance away from heat sources.
• Install the appliance in a dry, well-ventilated
place.
• Ensure that the appliance is level.
Adjust the front feet if necessary.
• Leave at least 5 cm clearance above the
appliance.
• The sides of some models are extended at
the rear so the appliance can be placed
directly against the rear wall. Otherwise, fit
the spacers (if supplied) on the upper part of
the condenser at the rear of the appliance.
For models without spacer walls, the
distance between the unit and the wall must
be at least 4.5 cm.
• Clean the inside (see the chapter “Care and
Maintenance”).
• Fit the accessories supplied.
• Remove the compressor locking pin
(according to the model).
Electrical connection
• Electrical connections must be made in
accordance with local regulations.
• Ensure that the voltage indicated on the
appliance data plate corresponds to the
domestic supply voltage.
• Regulations require that the appliance is
earthed.
The Manufacturer declines all liabilities
for injury to persons or animals or
damage to property resulting from failure
to observe these regulations.
• If the plug and socket are not of the same
type, have the socket replaced by a qualified
electrician.
• Do not use extension cables, multiple
sockets or adapters.
INSTALLATION
33124Gb.fm5 Page 74 Wednesday, February 23, 2000 9:03 AM
75
For Great Britain only
Warning
- this appliance must be
earthed
Fuse replacement
If the mains lead of this appliance is fitted with a
BS 1363A 13amp fused plug, to change a fuse in
this type of plug use an A.S.T.A. approved fuse
to BS 1362 type and proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a
fuse and if the fuse cover is lost the plug must not
be used until a correct replacement is fitted.
Correct replacement are identified by the colour
insert or the colour embossed in words on the
base of the plug.
Replacement fuse covers are available from
your local electrical store.
Connection to a rewirable plug
If the fitted plug is not suitable for your socket
outlet, then it should be cut off and disposed of in
order to avoid a possible shock hazard should it
be inserted into a 13A socket elsewhere.
A suitable alternative plug should then be fitted
to the cable.
The wires in the mains lead are coloured in
accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
1. The GREEN AND YELLOW wire must be
connected to the terminal in the plug which is
marked with the letter “E” or by the Earth
symbol or coloured green or green and
yellow.
2. The BLUE wire must be connected to the
terminal which is marked with the letter “N” or
coloured black.
3. The BROWN wire must be connected to the
terminal which is marked with the letter “L” or
coloured red.
For the Republic of Ireland only
The information given in respect of Great Britain
will frequently apply, but a third type of plug and
socket is also used, the 2-pin, side earth type. In
this case, the wire which is coloured GREEN
AND YELLOW must be connected to the EARTH
contact, and the two wires to the two pins,
irrespective of colour. The supply to the socket
must be fitted with a 16 amp fuse.
ELECTRICAL CONNECTION
33124Gb.fm5 Page 75 Wednesday, February 23, 2000 9:03 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Whirlpool ARZ 8970/H User guide

ARZ 8970/H
Whirlpool
Brand
Whirlpool
Model
ARZ 8970/H
Category
Fridge-freezers
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents