Whirlpool ART 800-2/H User guide

ART 800-2/H
Whirlpool
Brand
Whirlpool
Model
ART 800-2/H
Category
Fridge-freezers
Type
User guide
13
TABLE OF CONTENTS GB
BEFORE USING THE APPLIANCE
PAGE
14
SAFEGUARDING THE ENVIRONMENT
PAGE
14
PRECAUTIONS AND GENERAL HINTS
PAGE
15
HOW TO OPERATE THE REFRIGERATOR
COMPARTMENT
PAGE
16
HOW TO OPERATE THE FREEZER COMPARTMENT
PAGE
17
HOW TO DEFROST THE FREEZER COMPARTMENT
PAGE
19
CARE AND MAINTENANCE
PAGE
20
TROUBLESHOOTING GUIDE
PAGE
21
AFTER SALES SERVICE
PAGE
21
INSTALLATION
PAGE
22
ELECTRICAL CONNECTION
PAGE
23
14
Your new appliance is a combined fridge-freezer
exclusively for domestic use.
The
freezer compartment
can be
used for freezing fresh and cooked food, making
ice cubes and storing frozen food.
Defrosting
the freezer is a manual procedure
. The
refrigerator compartment,
which has
an
automatic defrost feature
, is used for the
storage of fresh food and beverages.
To make optimum use of your appliance,
read this user handbook thoroughly as it
contains a description of the appliance and
useful tips for storing food.
Keep this handbook for future consultation.
1.
After unpacking the appliance, make sure
that the doors shut properly. Any damage
must be reported to your retailer within 24
hours after delivery of the appliance.
2. Wait at least two hours without moving
the appliance before connecting it to the
power supply.
3.
Appliance installation and electrical
connections must be carried out by a
qualified technician in accordance with the
manufacturer’s instructions and local
regulations.
1. Packing
The packaging material is 100% recyclable
(marked with recycling symbol). Follow local
regulations for disposal.
The packaging material (plastic bags,
polystyrene parts, etc.) is potentially dangerous
and must be kept out of reach of children.
2. Product
The appliance is made using recyclable
materials and must be scrapped in accordance
with local waste disposal regulations.
Make the appliance unusable by cutting off the
power cord. Dispose of this appliance correctly.
Take it to an authorised collection centre for the
recovery of refrigerant gas.
Information:
This appliance does not contain CFCs (replaced
with R134a) or HFCs (replaced with R600a -
Isobutane). For more information, refer to the
rating plate affixed to the appliance.
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
15
•
Use the
refrigerator compartment
only for
storing fresh food and beverages and use the
freezer compartment
only for storing frozen food,
freezing fresh food and making ice cubes.
•
Do not cover or obstruct the air vents of the
appliance.
•
Do not store liquids in glass containers in the
freezer compartment - danger of bursting.
•
Do not eat ice cubes or ice lollies immediately after
taking them out of the freezer compartment - risk
of “cold” burns.
•
To avoid the risk of children becoming trapped or
suffocating, do not allow them to play or hide inside
the appliance.
•
Do not ingest the contents (non-toxic) of the ice
packs.
• Before cleaning or carrying out maintenance,
always unplug the appliance or switch the
power supply off.
•
The power cable can only be replaced by an
authorized person.
•
After installation, make sure that the appliance is
not resting on the supply cable.
Declaration of conformity
•
This appliance is intended to come into contact
with foodstuffs and conforms to D.L. 108 of
25.01.1992 (European Directive 89/109/EEC).
Information
Appliances with isobutane (R600a)
Isobutane is a natural gas having low environmental
impact. Caution is required, however, because
Isobutane is inflammable. Therefore, ensure that the
pipelines of the refrigerant circuit do not get damaged.
PRECAUTIONS AND GENERAL HINTS
16
This appliance is a refrigerator with
a
star
freezer compartment.
Defrosting of the refrigerator compartment is
completely automatic.
Optimal performance is obtained at
temperatures between +16°C and +32°C.
Switching on the appliance
Depending on the model, the appliance has
external (
A
) or internal (
B
) controls.
For appliances having
external controls (A)
:
press the startup button (A1).
•
The interior light switches on when the door
is opened.
•
Green LED (A2) switches on, indicating
operation of the appliance.
In models having
internal controls (B)
, when
the appliance is connected, the interior light
switches on when the door is opened if the
thermostat knob is not set on symbol z.
Important:
•
There is no need to adjust the thermostat
knob (
5
) as it has already been factory set to
ensure the correct storage temperature of
fresh food at ambient temperatures between
+20°C and +25°C.
•
After being switched on, the appliance needs
approx. 30 minutes to reach the correct
temperature to store a typical volume of food
in the refrigerator compartment.
Adjusting the temperature:
Turn the thermostat knob (
5
) setting:
•
to
lower numbers 1-2
if you require
HIGHER
TEMPERATURES
in the compartments.
•
to the
highest number
-
5 -
for
LOWER
TEMPERATURES.
To switch off the refrigerator compartment:
Press the ON/OFF button (A1) (if present;
alternatively, disconnect the plug from the
socket).
Using the refrigerator compartment
Position the food as shown in the figure.
A Cooked food
B Fish, meat
C Fruit and vegetables
D Bottles
E Butter
F Dairy products
.
Notes:
•
The space between the shelves and the rear
wall of the refrigerator compartment must be
unobstructed to allow air circulation.
•
Do not place the food in direct contact with the
rear wall of the refrigerator compartment.
•
Do not place hot food in the refrigerator or
freezer compartments.
•
Store liquids in closed containers.
•
Storing vegetables with high water content
can cause condensate formation in the
crisper: this will not affect the appliance's
efficiency.
.
HOW TO OPERATE THE
REFRIGERATOR COMPARTMENT
A
B
17
Important:
•
There is no need to adjust the thermostat
knob (
5
) as it has already been factory set to
provide the correct storage temperature of
frozen food in the freezer compartment at
ambient temperatures between +20°C
and +25°C.
•
After being switched on, the appliance needs
approx. 3 hours to reach the correct
temperature to store a typical volume of food
in the freezer compartment.
Adjusting the temperature:
Turn the thermostat knob (
5
) setting.
•
to
lower numbers
if the internal temperature
is too low.
•
to
higher numbers
to lower the internal
temperature.
Freezing fresh food
The freezer compartment
is used for
freezing fresh food.
The quantity of fresh food that can be frozen in
24 hours, at an ambient temperature of +25°C, is
indicated on the rating plate.
How to operate:
1.
Set the thermostat knob (
5
) on 2-3.
2.
If the appliance is equipped with a freeze
button (
4
), press it to activate the function
(the yellow LED switches on).
This operation makes it possible to obtain the
maximum freezing capacity indicated on the
rating plate and to avoid excessive lowering
of the refrigerator compartment temperature
during freezing.
3.
Wrap and seal the food in:aluminium foil,
cling film, air and water-tight plastic bags,
polythene containers with lids or special
freezer containers.
4.
Place food in the top compartment, leaving
enough space for air to circulate around
packages. To speed up the freezing process
and increase the compartment capacity,
remove the top basket and the ice pack
storage drawer (if provided). Put the already
frozen food into the other drawers and the
food still to be frozen directly onto the
refrigerator grid.
5.
The food will be completely frozen in 24
hours. Press freeze button (
4
) to deactivate
the function.
Note:
•
In the event of a power failure,
the freezer compartment will maintain the
storage temperature as indicated on the
product description sheet.
•
In models with one or two ice packs, this
temperature can be maintained for about 25/
30 hours.
•
Do not open the freezer compartment door
during a power failure.
HOW TO OPERATE THE FREEZER COMPARTMENT
18
Important:
For the periods of storage of frozen fresh foods,
refer to the adjacent table.
When purchasing frozen food products:
•
Ensure that the packaging is not damaged
(frozen food in damaged packaging may have
deteriorated). Avoid packages that are swollen or
show evidence of damp areas indicating that the
food may have thawed partially during its period of
storage.
•
When shopping, leave frozen food purchases till
last and transport the products in a thermally
insulated bag.
•
Place the items in the freezer compartment as
soon as you get home.
•
If food has thawed, even partially, do not re-freeze
it. Consume within 24 hours.
•
Avoid or reduce temperature variations to the
minimum. Respect the “best before” date on the
package.
•
Always observe the storage information on the
package.
Making ice cubes
•
Fill the ice cube tray 3/4 with water and place it in
the freezer compartment. To speed up the ice
making process, place the tray at the bottom of the
first basket (as shown in the figure) and not on the
ice rack (if provided).
•
Do not use sharp or pointed instruments to detach
the ice tray if it is stuck to the shelf.
HOW TO OPERATE THE FREEZER COMPARTMENT
MONTHS
FOOD
19
Defrost the freezer compartment once or twice a
year, or when the frost build-up on the walls
reaches a thickness of about 3 mm. Defrost the
appliance when there is very little food stored
inside.
1.
24 hours before defrosting, press the fast freeze
button (
4
). The yellow LED switches on. This
action brings the foods to the lowest possible
temperature.
2.
Open the door and remove the food from the
freezer compartment, wrap in sheets of
newspaper and group together in a cool place or in
a portable cooler.
3.
Disconnect the appliance from the mains supply.
4.
Remove the ice cube trays.
5.
Remove the baskets.
6.
Pull out the defrost water drain from the base of the
freezer compartment.
7.
Leave the freezer compartment door open.
Remove the drain plug (if present), place a
container (or the lower basket, if present) under
the drain to collect the defrost water, as shown in
the figure.
8. Note:
Do not use sharp or pointed instruments to
scrape off ice; do not heat the freezer
compartment artificially. Any damage to the
appliance resulting from failure to observe these
instructions is not covered by the guarantee.
9.
Clean the freezer compartment using a sponge
moistened with a solution of warm water and
neutral detergent. Do not use abrasive products.
10.
Rinse and dry thoroughly.
11.
Reconnect the appliance to the mains.
12.
Refit the drain in place and reposition the baskets.
13.
Press the freeze button (
4
) and leave the yellow
LED switched on for about 3 hours before
replacing the food in the freezer compartment. If
there is no freeze button (
4
), keep the thermostat
knob (
5
) turned to position 3 for about 4 hours
before replacing the food in the freezer.
Then return the thermostat knob to the normal
position.
Note:
The temperature rise of frozen food during
defrosting may shorten its storage life.
HOW TO DEFROST THE FREEZER COMPARTMENT
20
Before cleaning, unplug the appliance from the
mains.
•
Clean the inside of the freezer compartment when
defrosting.
•
Periodically clean the refrigerator compartment
with a sponge moistened with warm water and/or
neutral detergent. Rinse and dry with a soft cloth.
Do not use abrasive products.
•
Clean the outside with a soft cloth moistened with
water. Do not use abrasive products, scouring
pads, stain removers (e.g. acetone, trichloro-
ethylene) or vinegar.
•
Defrosting of the refrigerator compartment is
completely automatic. Some models are provided
with a drain hole. Periodically clean the inside
using the tool supplied to ensure constant and
proper drainage of the defrost water.
• Periodically clean the condenser at the rear of
the appliance and the plinth with a vacuum
cleaner or a brush.
Prolonged disuse
1.
Empty the refrigerator and freezer compartments.
2.
Disconnect the appliance from the mains.
3.
Defrost the freezer compartment, and clean and
dry both compartments.
4.
Leave the doors open to prevent formation of
unpleasant odours.
CARE AND MAINTENANCE
21
1. The appliance is not working.
•
Is there a power failure?
•
Is the plug properly inserted in the socket?
•
Is the electric power supply switched on?
•
Has the fuse blown?
•
Is the power cord in perfect condition?
•
Is the thermostat set to z (Stop)?
•
Is button 1 pressed?
2. Temperature inside the compartments is
not low enough.
•
Are the doors closed properly?
•
Is the appliance installed next to a heat
source?
•
Is the thermostat setting correct?
•
Are the air circulation grilles blocked?
•
Is the condenser clean?
3. Temperature inside the refrigerator
compartment is too low.
•
ls the thermostat setting correct?
4. Water collects at the bottom of the
refrigerator compartment.
•
Is the defrost water drain obstructed?
•
Is the thermostat setting correct?
5. The appliance is excessively noisy.
•
Is the appliance in contact with other units,
or objects?
•
Are the pipes at the back touching or
vibrating?
•
Has the compressor fixing block been
removed?
6. The interior light is not working.
Perform the checks for problem 1, and then:
•
Disconnect the appliance from the mains.
•
Remove the bulb cover.
•
Check the bulb, unscrew and replace it if
necessary. Do not exceed 15W.
Notes:
• The front edge of the appliance may be
hot. This prevents the formation of
condensation and is not a defect.
• Gurgling and hissing noises due to
expansion in the refrigerant circuit are
normal.
Before calling After Sales Service:
1.
See if you can solve the problem yourself
(see “Troubleshooting Guide”).
2.
Switch the appliance on to see if the problem
persists.
If it does, disconnect the appliance and wait
for about an hour before switching on again.
3.
If the problem persists, contact After Sales
Service.
Specify:
•
the nature of the fault,
•
the model,
•
the service number (the number after the
word SERVICE on the rating plate on the
inside of the appliance),
•
your complete address,
•
your telephone number and area code.
Note:
The direction of door opening can be
changed. If this operation is performed by
After Sales Service it is not covered by the
warranty.
TROUBLESHOOTING GUIDE
AFTER SALES SERVICE
22
•
Install the appliance away from heat sources.
•
Install the appliance in a dry, well-ventilated place.
•
Make sure that the appliance is level.
Adjust the front feet if necessary.
•
Leave at least 5 cm clearance above the
appliance.
•
In some models, the sides project to the rear so the
appliance can be placed in direct contact with the
rear wall.
Alternatively, fit the spacers (if supplied) on the
upper part of the condenser at the rear of the
appliance. For models without projecting sides, the
distance between the appliance and rear wall must
be at least 4.5 cm.
•
Clean the inside (see “Cleaning the Appliance”).
•
Fit the accessories supplied.
•
Remove the compressor fixing block (if supplied).
Electrical connection
•
Electrical connections must be made in
accordance with local regulations.
•
Ensure that the voltage indicated on the appliance
rating plate corresponds to the domestic supply
voltage.
• Appliance earthing is
compulsory by law.
The Manufacturer declines all liabilities for
injury to persons and animals or damage to
property resulting from failure to observe
these regulations.
•
If the plug and socket are not of the same type,
have the socket replaced by a qualified electrician.
•
Do not use extension cables, multiple sockets or
adapters.
INSTALLATION
23
For Great Britain only
Warning
- this appliance must be
earthed
Fuse replacement
If the mains lead of this appliance is fitted with a
BS 1363A 13amp fused plug, to change a fuse in
this type of plug use an A.S.T.A. approved fuse
to BS 1362 type and proceed as follows:
1.
Remove the fuse cover (A) and fuse (B).
2.
Fit replacement 13A fuse into fuse cover.
3.
Refit both into plug.
Important:
The fuse cover must be refitted when changing a
fuse and if the fuse cover is lost the plug must not
be used until a correct replacement is fitted.
Correct replacement are identified by the colour
insert or the colour embossed in words on the
base of the plug.
Replacement fuse covers are available from
your local electrical store.
Connection to a rewirable plug
If the fitted plug is not suitable for your socket
outlet, then it should be cut off and disposed of in
order to avoid a possible shock hazard should it
be inserted into a 13A socket elsewhere.
A suitable alternative plug should then be fitted
to the cable.
Connection to a rewirable plug
If the fitted plug is not suitable for your socket
outlet, then it should be cut off and disposed of in
order to avoid a possible shock hazard should it
be inserted into a 13A socket elsewhere.
A suitable alternative plug should then be fitted
to the cable.
1.
yellow.
2.
The BLUE wire must be connected to the
terminal which is marked with the letter “N” or
coloured black.
3.
The BROWN wire must be connected to the
terminal which is marked with the letter “L” or
coloured red.
For the Republic of Ireland only
The information given in respect of Great Britain
will frequently apply, but a third type of plug and
socket is also used, the 2-pin, side earth type.
In this case, the wire which is coloured GREEN
AND YELLOW must be connected to the EARTH
contact, and the two wires to the two pins,
irrespective of colour. The supply to the socket
must be fitted with a 16 amp fuse.
ELECTRICAL CONNECTION
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Whirlpool ART 800-2/H User guide

ART 800-2/H
Whirlpool
Brand
Whirlpool
Model
ART 800-2/H
Category
Fridge-freezers
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents