Tyan S5105 User manual

Tomcat i875PF S5105 User’s Manual

i

http://www.tyan.com

Tomcat i875PF

///

S5105

Revision 1.00

may be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Tomcat, i875PF and S5105 are trademarks of TYAN Computer Corporation.

Intel, Pentium 4, and combinations thereof are trademarks of Intel Corporation.

Award, AwardBIOS are trademarks of Award Software Incorporated.

Microsoft and Windows are trademarks of Microsoft Corporation.

IBM, PC, AT and PS/2 are trademarks of IBM Corporation.

ATI, ATI RAGE is a trademark of ATI Technologies Incorporated.

Winbond is a trademark of Winbond Electronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has

been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability

whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for a particular purpose or

merchantability. TYAN retains the right to make changes to product descriptions and/or

specifications at any time, without notice. In no event will TYAN be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Tomcat i875PF S5105 Table of Contents

ii

http://www.tyan.com

Table of Contents

Before you begin… ................................................................................................................. iii

Chapter 1: Introduction............................................................................................................ 1

1.1 – Congratulations!......................................................................................................... 1

1.2 – Hardware Specifications ............................................................................................ 1

Chapter 2: Board Installation .................................................................................................. 3

2.1 – Board Parts ................................................................................................................ 4

2.2 – Block Diagram............................................................................................................ 5

2.3 – Jumper and Connector Settings ................................................................................ 6

2.4 – Mounting the Motherboard ....................................................................................... 13

2.5 – Installing the Memory............................................................................................... 14

2.6 – Memory Installation Procedure ................................................................................ 15

2.7 – Installing the Processor and Heatsink...................................................................... 16

2.8 – Attaching Drive Cables ............................................................................................ 18

2.9 – Installing Add-In Cards............................................................................................. 20

2.10 – Connecting External Devices................................................................................. 21

2.11 – Installing the Power Supply.................................................................................... 21

2.12 – Finishing Up ........................................................................................................... 22

Chapter 3: BIOS Setup...........................................................................................................23

3.1 – Main BIOS Setup ..................................................................................................... 25

3.2 – Standard CMOS Features ....................................................................................... 26

3.3 – Advanced BIOS Features ........................................................................................ 28

3.4 – Advanced Chipsets Features................................................................................... 31

3.5 – Integrated Peripherals.............................................................................................. 32

3.6 – Power Management Setup ...................................................................................... 37

3.7 – PnP/PCI Configurations ........................................................................................... 41

3.8 – PC Health Status ..................................................................................................... 42

3.9 – Frequency/Voltage Control ...................................................................................... 43

3.10 – Load Fail-Safe Defaults ......................................................................................... 44

3.11 – Load Optimized Defaults........................................................................................ 44

3.12 – Supervisor/User Password Setting ........................................................................ 45

3.13 – Exit Selecting ......................................................................................................... 46

Chapter 4: SATA/RAID Setup................................................................................................ 48

4.1 BIOS Configuration ..................................................................................................... 48

4.2 Installing Serial ATA (SATA) hard disks ..................................................................... 48

4.3 Creating, Deleting, and Resetting RAID Volumes ...................................................... 49

4.4 Create RAID 0 or RAID 1 Volume............................................................................... 50

4.5 Delete RAID Volume................................................................................................... 51

4.6 Reset Disks to Non-RAID ........................................................................................... 52

4.7 Pre-Installation of the Intel® RAID Driver ................................................................... 53

4.8 Using the Intel® Application Accelerator RAID Edition Utility ..................................... 54

4.8.1 Installing the Intel® Application Accelerator RAID Edition ....................................... 54

4.8.2 RAID Migration Instructions ..................................................................................... 54

4.8.3 Uninstalling the Intel® Application Accelerator RAID Edition................................... 60

Chapter 5: Diagnostics ..........................................................................................................62

5.1 Beep Codes ................................................................................................................ 62

5.2 Flash Utility.................................................................................................................. 62

Appendix I: Glossary ............................................................................................................. 63

Appendix II: Post Error Code for BIOS ................................................................................ 69

Appendix III: SMDC Information ........................................................................................... 74

Technical Support ............................................................................................................. 75

Tomcat i875PF S5105 Before you begin…

iii

http://www.tyan.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Tomcat i875PF S5105 motherboard

1x 34-Pin floppy drive cable

1x Ultra-DMA-133/100/66/33 IDE cable

1 x Serial ATA power cable

2 x Serial ATA cable

1x Tomcat i875PF S5105 User’s Manual

1x Tomcat i875PF S5105 Quick Reference Guide

1x TYAN driver CD

1x I/O shield

1 x Serial ATA driver diskette

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

Tomcat i875PF S5105 Chapter 1: Introduction

1

http://www.tyan.com

Chapter 1: Introduction

1.1 – Congratulations!

You have purchased one of the most powerful solutions for the Intel® Pentium



4 processor,

the Tomcat i875PF S5105 Based on Intel® 875P chipset, this platform offers convenient

remote Intelligent Platform Management Interface (IPMI) monitoring through a Server

Management Daughter Card. The Tomcat i875PF S5105 are Flex ATX form factor, onboard

dual Gigabit Ethernet port, Serial ATA, and an onboard ATI 8MB PCI RAGE XL VGA.

Remember to visit TYAN’s Website at http://www.tyan.com

. There you can find information on

all of TYAN’s products with FAQs, distributors list, and BIOS setting explanations.

1.2 – Hardware Specifications

PROCESSOR

 Socket 478

 Intel® Pentium 4 Processors,

“Northwood/Prescott”

 On-board VRM 10.0

 800/533/400 MHz System Bus support

CHIPSET

 Intel® 875P chipset

 MCH + ICH5R

 Winbond W83627HF Super I/O chip

EXPANSION SLOTS

 Total two 32-bit/33MHz PCI v2.2 slots

MEMORY

 Dual Channel Memory Bus

 Four DDR DIMM slots

 DDR 266/333/400 supported

 Max. 4 GB with Unbuffered DDR

 Supports non-ECC/ECC type memory

modules

 Registered RAM not supported

INTEGRATED LAN

 Intel® 82547 CSA 10/100/1000 controller

 Intel® 82540/82541 PCI 10/100/1000

controller

 WOL/PXE/ASF2.0 support

 Two RJ-45 LAN connectors w/ LEDs

INTEGRATED PCI GRAPHICS

 ATI RageTM XL PCI graphics

controller

 8MB Frame Buffer of video memory

BIOS

 Award BIOS on 4Mb Flash (FWH)

 ACP1.1/APM1.2

 User settings of HW monitoring

 Auto configuration of IDE hard disk

types

 Quick boot and multiple boot options

 LAN remote boot (PXE) support

 Event Log support (4K EEPROM)

 Power Management: S1, S3, S4 and

S5

SYSTEM MANAGEMENT

 W83627HF HW monitoring

 One 3-pin CPU fan header with

temperature controlled

 Two 3-pin chassis fan headers with

temperature controlled

 2-pin Chassis Intrusion header

 Two temperature sensors and voltage

monitoring

 Watchdog timer

 Supports Tyan Server Management

Daughter card (SMDC*) via Tyan-

defined header

Tomcat i875PF S5105 Chapter 1: Introduction

2

http://www.tyan.com

INTEGRATED I/O

 One Floppy connector for up to two drives

 Two 9-pin UART Serial ports (one header

via cable)

 Four USB 2.0 Ports (2 rear ports and 2

headers)

 PS/2 Mouse & Keyboard ports

INTEGRATED PCI ATA AND SATA

 Intel® ICH-5 or ICH-5R

 Up to four Enhanced UDMA and SATA

devices

 Dual channel UDMA Master mode for up

to 4 devices

− Supports for UDMA 33/66/100 IDE

drives and ATAPI compliant devices

 Support two independent SATA ports

− Data transfer at 1.5 Gb/s

− Supports RAID 0 or 1

FORM FACTOR

 Flex ATX (9.0” x 8.0”)

 ATX12V power connectors

 Side by side PS2 Mouse/Keyboard

connectors

 Stacked 2 USB connectors and RJ45

LAN connector w/LEDs

 One Serial connector

 One VGA connector

 One RJ45 LAN connectors w/ LEDs

REGULATORY

 FCC Class B (Declaration of

Conformity)

 CE (Declaration of Conformity)

* Tyan SMDC is a System Management

Daughter Card. It enables you to access

the hardware remotely and perform

monitor, control, and diagnose activities

effectively.

See Appendix III (Pg 75) for details In

Tyan SMDC.

Software Specifications

OS (Operating System) Support

Microsoft Windows Server 2000

Microsoft Windows Advanced Server 2000

Microsoft Windows XP

Microsoft Windows Server 2003

Red Hat 8.0, 9.0

FreeBSD5.1

Solaris 9.0

Other distributions of Linux pending validation

Note: TYAN reserves the right to add support or discontinue support for any OS with or

without notice.

Tomcat i875PF S5105 Chapter 2: Board Installation

3

http://www.tyan.com

Chapter 2: Board Installation

Installation

You are now ready to install your motherboard. The mounting holes pattern of the Tomcat

i875PF S5105 matches the Flex ATX specification. Before continuing with installation, confirm

that your chassis supports a standard Flex ATX motherboard.

How to install our products right…. the first time!

The first thing you should do read this user’s manual. It contains important information that

will make configuration and setup much easier. Here are some precautions you should take

when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch a safely

grounded object to release static charge (i.e. power supply case). For the safest

conditions, TYAN recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex

the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors, memory

modules and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag that

the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis, as

well as installing the processor, memory, disk drives and cables.

Note: DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

Tomcat i875PF S5105 Chapter 2: Board Installation

4

http://www.tyan.com

2.1 – Board Parts

This jumper diagram is representative of the latest board revision available at the time

of publishing. The board you receive may or may not look exactly like the above

diagram. The board parts are not to scale.

Tomcat i875PF S5105 Chapter 2: Board Installation

5

http://www.tyan.com

2.2 – Block Diagram

The following is a block diagram of the Tomcat i875PF S5105.

PS/2

KBD & MS

800/533/400 MHz FSB

FDD

Port

Serial

Port

Serial

Port

LPC Bus

2 PCI Slots

PCI BUS

266MB/

s

H

ub Link 1.

5

266

MB/S

ECC / Non-ECC

DDR 266 / 333 / 400

Memory

Channel A

Channel B

LPC

Su

p

er I/O

2 x ATA

100/66/33

Ports

USB 2.0

2 Ports and 2

front Headers

Gigabit LAN

Intel

82540

/

82541

ATI

Rage XL

Intel

82801ER

ICH5-R

2 x SATA Ports

150MB/S

mPGA478 Socket

for Prescott or

Northwood CPU

Intel 82875P

MCH

CSA Gigabit LAN

Intel 82547

BIOS

Parallel

Port

Tomcat i875PF S5105 Chapter 2: Board Installation

6

http://www.tyan.com

2.3 – Jumper and Connector Settings

Jumper or Connector Functions Ref. Page

J9 Front USB Header Page 7

J10 External Speaker Header Page 7

J13 SATA LED Header Page 8

J18 CMOS Reset Page 8

J20 Front Panel Connector Page 9

J21 Chassis Intrusion Header Page 9

J42 SMDC Connector Page 10

J43 Serial Port Internal Header Page 10

J44 Parallel Port Internal Header N/A

FAN1 ~ FAN4 Fan Connectors Page 11

SATA1 ~ SATA2 SATA Connectors Page 11

LAN1 Intel® 82547 GbE connector Page 12

LAN2 Intel® 82540/82541 GbE connector Page 12

Jumper Legend

Jumper OFF – OPEN (without jumper cap)

Jumper ON – CLOSED (with jumper cap)

To indicate the location of pin-1

Tomcat i875PF S5105 Chapter 2: Board Installation

7

http://www.tyan.com

Front USB Header (J9)

Signal

Description

Pin #

Signal

Description

VCC 1 2 VCC

USB

Channel_1

Data -

3 4

USB

Channel_2

Data -

USB

Channel_1

Data +

5 6

USB

Channel_2

Data +

GND 7 8 GND

NC 9 10 GND

External Speaker Header (J10)

Pin_1

Pin_4

Pin_1 : Speaker +

Pin_2 : Buzzer +

Pin_3 : Speaker/ Buzzer –

Pin_4 : Speaker -

Close Pin-2and Pin-3 (Default)

Enable onboard buzzer

Open Pin-1 ~ Pin-4

Disable onboard buzzer and can connect

to chassis 1x4 speaker by Pin_1 and

Pin_4

Tomcat i875PF S5105 Chapter 2: Board Installation

8

http://www.tyan.com

SATA LED Header (J13)

1 2

Pin_1 SATA LED+

Pin_2 GND

CMOS Reset (J18)

Pin_1

Clear COMS

Pin_1

Normal

You can reset the CMOS settings in case an

incorrect setting causes system instability or

you have forgotten your system / setup

password or have just flashed your BIOS by

using these jumpers.

- Power off system, disconnect power supply

from the motherboard

- Set jumper to Clear CMOS

- Wait about 5 seconds

- Set jumper to Normal (Default)

And plug the power supply back into the

motherboard.

Tomcat i875PF S5105 Chapter 2: Board Installation

9

http://www.tyan.com

Front Panel Connector (J20)

Your chassis will usually come with connectors to install onto the motherboard, such as HD

and Power LEDs. The Front Panel Connector (J20) has been implemented for such purposes.

Function Pin Pin Function

HDD_LED+ 1 2 PWR_LED+

HDD_LED- 3 4 PWR LED -

Reset Button - 5 6 PWR Button+

Reset Button+ 7 8 PWR Button-

+5V 9

10

NC

IR_RX 11 12 Power

GND 13 14 NC

IR_TX 15 16 NC

Reserved 17 18 Reserved

Chassis Intrusion Header (J21)

1 2

Pin_1 INTRUDER_L

Pin_2 GND

If you would like to protect your

system from outside intrusion, the

detect connector is available for

deployment.

Note: For use with chassis that

support this feature.

Tomcat i875PF S5105 Chapter 2: Board Installation

10

http://www.tyan.com

SMDC Connector (J42)

Connect Server Management Daughter

Card (SMDC)

Compatible with Tyan M3289 (SMDC)

See Appendix III for details In Tyan

SMDC

Serial Port Internal Header (J43)

Signal

Description

Pin # Pin #

Signal

Description

DCD

(Data Carrier

Detect)

1 2

DSR (Data-Set-

Ready)

RXD (Receive-

Data)

3 4

RTS (Request-

to-Send)

TXD (Transfer-

Data)

5 6

CTS (Clear-to-

Send)

DTR (Data-

Terminal-

Ready)

7 8

RI (Ring-

Indicator)

GND 9 10 NC

Tomcat i875PF S5105 Chapter 2: Board Installation

11

http://www.tyan.com

Fan Connectors (FAN 1 & FAN 2 & FAN 3 & FAN 4)

+12V fans supported

Use these connectors to connect cooling

fans, both chassis and processor fans, to

your motherboard. Cooling fans help

keep the system more stable and

operating reliably for its product life.

FAN # Description Functions

Amp Rated

(Maximum)

1 CPU Fan Tachometer/speed Read and controlled 1.5A

2 Chassis Fan Tachometer/speed Read and controlled 1.0A

3 Chassis Fan Tachometer/speed Read and controlled 1.0A

4 Chassis Fan None 0.8A

Serial ATA Connectors (SATA1 & SATA2)

SATA1 / SATA2 (from ICH5-R): Support SATA RAID 0 or 1

1 7

Pin1 234567

Signal GND TXP TXN GND RXN RXP GND

Supports serial ATA devices

Tomcat i875PF S5105 Chapter 2: Board Installation

12

http://www.tyan.com

Onboard LAN LED Color Definition

LAN1---Intel® 82547 GbE NIC activity/link LED information

Left LED Right LED

Network link not established Off Off

Linked at 10 Mbps (10 BaseT)

Activity at 10 Mbps

Off

Green

Blink Green

Linked at 100 Mbps (100 BaseTX)

Activity at 100 Mbps

Yellow

Blink Yellow

Off

Linked at 1000 Mbps (1000 BaseT)

Activity at 1000 Mbps

Yellow

Blink Yellow

Green

Blink Green

LAN2---Intel® 82540/52541 GbE NIC activity/link LED information

Left LED

Right LED

Network link not established Off Off

Linked at 10 Mbps (10 BaseT)

Activity at 10 Mbps

Off

Green

Blink Green

Linked at 100 Mbps (100 BaseTX)

Activity at 100 Mbps

Yellow

Blink Yellow

Off

Linked at 1000 Mbps (1000 BaseT)

Activity at 1000 Mbps

Yellow

Blink Yellow

Green

Blink Green

Tomcat i875PF S5105 Chapter 2: Board Installation

13

http://www.tyan.com

2.4 – Mounting the Motherboard

Before installing your motherboard, make sure your chassis has the necessary motherboard

support studs installed. These studs are usually metal and are gold in color. Usually, the

chassis manufacturer will pre-install the support studs. If you’re unsure of stud placement,

simply lay the motherboard inside the chassis and align the screw holes of the motherboard to

the studs inside the case. If there are any studs missing, you will know right away since the

motherboard will not be able to be securely installed.

Some chassis’ include plastic studs instead of metal. Although the plastic studs are usable,

TYAN recommends using metal studs with screws that will fasten the motherboard more

securely in place.

- Memory Type: The Tomcat i875PF S5105 supports unbuffered ECC and non-ECC type

memory modules. Registered Memory is NOT supported.

Below is a chart detailing what the most common motherboard studs look like and how they

should be installed it.

TIP: Use metal studs if possible, as they hold the motherboard into place more securely than

plastic standoffs.

Tomcat i875PF S5105 Chapter 2: Board Installation

14

http://www.tyan.com

2.5 – Installing the Memory

Before attempting to install any memory, make sure that the memory you have is compatible

with the motherboard as well as the processor. For example, while PC1600 DDR modules are

compatible with all DDR based motherboards, they will not work if you are required to run the

motherboard and processor buses at 133MHz. For this, PC2100 DDR modules are required.

Critically important is whether you’re using the recommended memory for the current board

you have. For this information, please check TYAN’s web site at: www.tyan.com

The following diagram shows the types of RAM modules you may encounter depending on

your board:

DDR Unbuffered ECC

DDR Unbuffered

Here are a few key points to note before installing memory into your Tomcat i875PF S5105:

• 128MB, 256MB, 512MB and 1GB unbuffered ECC and non-ECC

PC2100/PC2700/PC3200

DDR memory modules are supported

• All installed memory will be automatically detected - no need to set any jumpers

• The Tomcat i875PF S5105 supports up to 4GB of memory

• Registered Memory is NOT supported.

• You can install either single- or double-sided modules on this board. Each DIMM

can work respectively for single-channel mode and dual-channel mode. Please note

that the same type and density memory modules are necessary while using dual-

channel DDR, otherwise it may cause system instability.

Please refer to the following table for detailed dual-channel DDR.

Channel A Channel B Dual-Channel Mode

DIMM1 DIMM2 DIMM3 DIMM4

System

Density

Two DIMM Symmetrical

Population

 

256MB~2GB

Two DIMM Symmetrical

Population

 

256MB~2GB

Four DIMM Symmetrical

Population

   

512MB~4GB

Note

1. : Installing128MB~1GB Memory modules

2. Symmetrical DIMMs must be identical

- Same DRAM Technology, eg 128M-bit, 256-bit, etc.

- Same DRAM bus width, eg x8 or x16

- Matched Sided DIMMs (Single Sided or Double Sided)

Tomcat i875PF S5105 Chapter 2: Board Installation

15

http://www.tyan.com

• Supported System Bus Frequency and Memory Speed Combinations

To use this type of DIMM… The processor’s system bus frequency must be…

DDR400 800MHz

DDR333 *800MHz or 533MHz

*When using an 800MHz system bus frequency processor, DDR333 memory is clocked at 320MHz.

This minimizes system latencies to optimize system throughput.

NOTE:

While using ECC type memory, it will take longer time to post. Due to the manner in which it

counts the memory and has to write zero’s to every bit of the stick before progressing through

the POST.

2.6 – Memory Installation Procedure

When installing memory modules, make sure the modules align properly with the memory

socket. There should be keys (small indents) on your memory modules that fit according to the

keys in the memory socket. DDR modules and sockets have only one key, which is slightly

near the center of the module/socket. The method of installing memory modules is detailed in

the following diagrams.

Once the memory modules are firmly seated in the socket, two clamps on either side will close

and secure the module into the socket. Sometimes you may need to close the clamps

manually.

To remove the memory module, simply push the clamps outwards until the memory module

pops up. Then simply remove the module.

Tomcat i875PF S5105 Chapter 2: Board Installation

16

http://www.tyan.com

TIP: When installing memory, a module may require a considerable amount of force to seat

properly, although this is very rare. To avoid bending and damaging your motherboard, place

it on its anti-static bag and onto a flat surface, and then proceed with memory installation.

Note: You MUST unplug the power connector to the motherboard before performing system

hardware changes, to avoid damaging the board or expansion device

2.7 – Installing the Processor and Heatsink

Your Tomcat i875PF S5105 supports the latest processor technologies from Intel®. Check

the following page on TYAN’s website for latest processor support:

http://www.tyan.com

The following diagrams will detail how to install your processor:

The diagram is provided as a visual guide to help you install socket processors and may not

be an exact representation of the processors you have.

1. Lift the lever on the socket until it is approximately 90

o

or as far back as

possible to the socket.

2. Align the processor with the socket. There are keyed pins underneath the processor

to ensure that the processor’s installed correctly.

3. Seat the processor firmly into the socket by gently pressing down until the processor

sits flush with the socket.

4. Place the socket lever back down until it locks into place.

5. Your processor is installed.

Take care when installing the processor as it has very fragile connector pins below the

processor that can bend and break if inserted improperly.

Tomcat i875PF S5105 Chapter 2: Board Installation

17

http://www.tyan.com

Heatsink Installation

After you are done installing the processor, you should proceed to installing the heatsink.

Heatsink will ensure that the processor not overheat and continue to operate at maximum

performance for as long as you own them. An overheated processor is dangerous to the

health of the motherboard.

Because there are many different types of heatsinks available from many different

manufacturers, a lot of them have their own method of installation. For the safest method of

installation and information on choosing the appropriate heatsink, please refer to INTEL’s

website at www.Intel.com.

The following diagram will illustrate how to install the most common heatsinks:

Install the mounting bracket onto the

motherboard by aligning the bracket with the four

holes around the processor socket. Once the

bracket is aligned, press down on the four white

pegs on the bracket until they insert securely,

locking the bracket onto the motherboard. Then

proceed to installing the heatsink. Instructions on

how to install heatsinks should be provided with

the heatsink itself.

First, use thermal compound (also

called heatsink compound or thermal

grease) and apply a small amount on

to the processor’s core – the small

shiny square in the center of the

processor.

You may then use a small soft plastic

tool, like a credit card to gently smear

a thin layer of heatsink compound as

evenly as you can across the core. In

most cases, you don’t need to do this

but it may help.

Then, at an angle, clip one side of the

heatsink onto the socket and then lay

the heatsink flat onto the processor.

Then clip the other end of the heatsink

down either with your finger or by

using a flathead screwdriver.

Some heatsinks have a small clip on

the inside of one of the clips which

you can insert a small flathead screw

driver into to secure the heatsink.

In most cases, either side of the

heatsink can be clipped down last, but

usually, the side of the socket where it

is raised, secures last.

Because one side of the socket is

raised (and usually has “SOCKET”

imprinted into it) heatsinks have an

indent on one side to secure flush with

the raised side of the socket.

Be sure to carefully observe which

side your heatsink is seated before

securing it down to avoid damaging

the processor, the heatsink or both.

Page is loading ...

Tyan S5105 User manual

This manual is also suitable for

Tyan S5105 User manual

Related papers

Other documents