Distributeur d'eau
Water dispenser
Distribuidor de agua
Distribuidor de água
Waterautomaat
IT Libretto istruzioni Distributore d'acqua
Vanddispenseren
Wasserspender
6
- Before using your water dispenser, please read the instructions in this manual carefully.
- When unpacking the product, please ensure that the BARAO is not damaged. If the drinks
dispenser seems to be defective, please contact the After-Sales Service.
- You must scrupulously observe the following instructions. We decline any responsibility and
rescind any guarantee in the event of non-observance of these instructions, which can cause
material damage or physical injury.
- Before using your dispenser for the first time, we recommend that you service the circuit and all
the receptacles (see the "Maintenance Instructions" section)
We strongly recommend that you avoid using the BARAO with fizzy drinks.
If you are using the BARAO as a dispenser of infusions (tea, tisanes, etc), we recommend that you
use a filter. The dispenser must be regularly serviced (see the "Maintenance Instructions" section).
We would strongly advise against using the appliance with drinks with a high sugar content (fruit
juice, syrups, aperitifs, etc.), which would damage the system and cause hygiene concerns inside
the refrigerator.
The BARAO is a system that enables you to
serve cold drinks at any time of day without
opening the door of your refrigerator, thereby
saving on energy consumption. You do not
need a water connection to use your
appliance.
The unit is totally integrated into your refriger-
ator's door and consists of the following three
main elements:
- A reservoir (in the inner door)
- A water dispenser (on the front surface)
- The distribution circuit (fixed on the door)
Reservoir
The reservoir consists of (drawing 1):
- A receptacle (E)
- A cover (I)
- A valve with spring and ring (D)
- A filter holder (H)
- A filter (G) for purifying the tap water (sup-
plied separately from your After-sales Service
or your authorized Clearit distributor).
- The filter must be changed after one month's
use.
General recommendations
EN
Instructions
Description of the dispenser
Drawing 1
I
G
H
E
D
F
7
Dispenser
The dispenser (drawing 2) consists of:
- A blanking plate to cover the circuit (A)
- A removable anti-drip system holder (B)
- A distribution lever (C)
Circuit
The circuit (F) is fixed on the door and protect-
ed by plastic supports.
You do not need to remove the supports to
service the distribution circuit (please refer to
the Maintenance Instructions section).
Maintenance of the circuit
- Fill the reservoir with hot water mixed with white vinegar and empty it using the dispenser.
- Then rinse thoroughly with fresh water.
Maintaining the removable parts
- Remove the reservoir, the cover and the filter holder and clean them using detergent mixed with
water.
- Rinse thoroughly.
Maintaining the reservoir valve
- Remove the ring by pushing it downwards and turning it to the right.
- Remove the spring from the valve.
- Wash them using a flexible brush and a warm vinegar and water mixture.
- Rinse everything in fresh water.
- Refit the ring and the valve by pushing downwards and turning counter-clockwise.
Maintaining the anti-drip system holder
- Remove the holder (drawing 3) and clean it
by hand with water and detergent .
- Never use solvents to clean the Barao
system's components.
- Please refer to the user's manual for our
instructions on the general maintenance of
your refrigerator.
Description of the dispenser
EN
Drawing 2
A
C
B
Maintenance instructions
Drawing 3
8
You do not need to use the filter if you fill the
reservoir with bottled water.
The reservoir can either be filled directly in the
inner door or by removing it to fill it with
running water.
If you use Barao with running water, we
recommend that you use a filter (supplied
separately from your After-sales Service or
your authorized Clearit distributor).
The filter must be changed after one
month's use.
- Insert the filter in the holder (drawing 4).
- Insert the holder in the reservoir (drawing 4).
You can fill the reservoir directly in the door
without removing it if you use a bottle or under
the tap by removing the reservoir as shown in
the drawing 5.
- Remove the cover (drawing 5).
- Fill via the top part of the reservoir and wait
for the water to pass completely through the
filter and then continue filling.
- Replace the cover over the reservoir. Fit the
reservoir in its holder taking care to position
the valve correctly.
To fill the reservoir directly in the door, remove
the cover by pulling on the two side pieces
(drawing 6).
- Fill the reservoir.
- Refit the cover.
To serve yourself with a drink, press a glass or
a carafe under the dispenser and push
upwards slightly (drawing 7).
Operating instructions
EN
Drawing 6
Drawing 4
Drawing 5
Drawing 7
9
Operating anomalies
EN
ANOMALIES ADVICE
Your appliance does not
distribute water
- Check that the reservoir is correctly engaged in its housing.
Water leak inside the refrigerator
on the lower part of the
distribution circuit (drawing 1 -
element F)
- Check that the reservoir is correctly engaged in its housing.
- Check that the carafe sealing joint is correctly engaged in its
housing.
Reservoir difficult to extract
from its housing
- Pull it upwards, first to the right and then to the left in a rocking
motion (drawing 8).
Drops after water distribution
- We would recommend that you hold the glass for one second
longer after distribution to avoid drips.
Water loss from the reservoir
valve
- Check that the valve is correctly engaged in its housing.
Reservoir difficult to insert
in its housing
- Moisten the reservoir sealing joint with water.
Drawing 8
-
1
-
2
-
3
-
4
-
5
Brandt D3120X Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Kenmore 625344800 User manual
-
Baumatic PECM1SS User manual
-
Miele G 666 Owner's manual
-
WaterLogic WL270 Operating, Installation And Service Manual
-
-
-
-
Miele G 665 SCG665SC Owner's manual
-
-