Air Lift 94375 Installation guide

Air Lift
Brand
Air Lift
Model
94375
Type
Installation guide

This manual is also suitable for

Kits 57375 | 88375 | 89375
4WD
For maximum effectiveness and safety, please read these instructions
completely before proceeding with installation.
Installation
Guide
MN-1080 • (031909) • ECR 9387
Failure to read these instructions can result in an incorrect installation.
RAM 1500
SERIES
IDENTIFYING THE DIFFERENCES BETWEEN KITS
Should you need to contact Air Lift customer service, you will need to know which kit you are inquiring about:
standard LoadLifter 5000, LoadLifter 5000 Ultimate or LoadLifter 5000 Ultimate Plus. The kits are easily
identifiable by looking
at the roll plates and air lines.
Standard LoadLifter 5000 — Zinc-plated steel roll plates and black nylon air lines.
LoadLifter 5000 Ultimate — Black powder-coated roll plates and black nylon air lines.
LoadLifter 5000 Ultimate Plus — Stainless steel roll plates, braided stainless steel air lines, stainless steel
air spring mounting hardware.
Air Lift offers two Ultimate Plus upgrade kits:
52300 - Braided stainless steel air line and fittings.
52301 - Stainless steel roll plates, air spring mounting hardware, braided stainless steel air lines and fittings.
LoadLifter 5000 Ultimate
black powder-coated
roll plate
LoadLifter 5000 Ultimate Plus
stainless steel
roll plate
LoadLifter 5000
silver zinc-plated steel
roll plate
LoadLifter 5000 Ultimate
nylon air line
LoadLifter 5000 Ultimate PLUS
braided stainless steel air line
LoadLifter 5000
nylon air line
TABLE OF CONTENTS
A. Installation Diagram ................................ 2
B. Hardware and Tools Lists ........................... 3
C. Introduction ....................................... 4
Notation Explanation ...................................................4
D. Installing the LoadLifter 5000 Series System ............ 5
Preparing the Vehicle ...................................................5
Assembling the Air Springs ..............................................7
Installing the Upper Brace ...............................................8
Installing the Assemblies ................................................9
E. Installing the Air Lines ..............................13
Installing Nylon Air Lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installing Braided Stainless Steel Air Lines ..................................14
Installing the Heat Shield ............................................... 15
F. Finished Installation ................................16
Installation Checklist ...................................................17
Maintenance and Use Guidelines ......................................... 17
Limited Warranty and Return Policy ....................................... 17
LoadLifter 5000 Series
MN-1080
2
A. Installation Diagram
G
I
C
L
M
N
B
G
J
D
E
D
A
2
G
I
K
A2
g. A.1
Passenger’s
(Right) Side
CAUTION
PROFESSIONAL
MECHANIC SKILLS
ARE REQUIRED TO
COMPLETE THE
INSTALLATION OF
THIS KIT.
LoadLifter 5000 Series
MN-1080
3
Item Part# Description ........................................................ Qty
D 11951 Zinc-coated roll plate .............................................. 4
E 58437 Air spring ................................................................. 2
J 21837 1/8” MNPT-1/4” Swivel elbow fitting ....................... 2
K 17215 3/8”-24 x 3/4” Flat head socket cap screw ............ 4
L 17203 3/8”-24 x 7/8” Hex cap screw................................. 4
M 18427 3/8” Split lock washer ............................................. 4
N 18444 3/8” Flat washer ...................................................... 4
AA* 20086 Air line assembly ..................................................... 1
EE* 21233 5/16” Hex nut .......................................................... 4
II* 21230 Valve cap ................................................................. 2
STOP!
B. Hardware and Tools Lists
TOOLS LIST
KIT 57375
KIT 88375
KIT 89375
Item Part# Description ........................................................ Qty
A1 03017 Left-hand lower bracket .......................................... 1
A2 03625 Right-hand lower bracket ....................................... 1
B 07652 Upper bracket ......................................................... 2
C 11652 Upper brace ............................................................ 2
F* 13978 Spacer ..................................................................... 1
G 17134 3/8”-16 x 1” Carriage bolt ..................................... 12
H* 17252 M8-1.25 x 35 Hex flange bolt ................................. 1
I 18422 3/8”-16 Serrated flange nut .................................. 12
O* 11968 3/8” Wire bolt leader tool ........................................ 2
BB* 10466 Zip ties .................................................................... 6
CC* 18411 5/16” Lock washer .................................................. 2
FF* 21234 Rubber washer ........................................................ 2
JJ* 18501 M8 Flat washer........................................................ 2
Common Parts Included in All 3 Kits
Item Part# Description ........................................................ Qty
D 11967 Black powder coated roll plate ............................... 4
E 58496 Air spring with integrated jounce bumper ............... 2
J 21837 1/8” MNPT-1/4” Swivel elbow fitting ....................... 2
K 17215 3/8”-24 x 3/4” Flat-head socket cap screw ............ 4
L 17203 3/8”-24 x 7/8” Hex-cap screw ................................ 4
M 18427 3/8” Split lock washer ............................................. 4
N 18444 3/8” Flat washer ...................................................... 4
AA* 20086 Air line assembly ..................................................... 1
EE* 21233 5/16” Hex nut .......................................................... 4
II* 21230 Valve cap ................................................................. 2
Unique Parts in Each Kit
The photos in this manual show the LoadLifter 5000 kit.
Item Part# Description .......................................................... Qty
D 11880 Stainless steel roll plate ............................................ 4
E 58496 Air spring with integrated jounce bumper ................. 2
J 21815 AN-Type fitting .......................................................... 2
K 17363
3/8”-24 x 3/4” Stain. steel flat-head socket cap screw
... 4
L 17284 3/8”-24 x 7/8” Stainless steel hex cap screw ........... 4
M 18504 3/8” Stainless steel split lock washer ....................... 4
N 18507 3/8” Stainless steel flat washer ................................. 4
AA* 20084 Nylon air line ............................................................. 1
DD* 20987 Braided stainless steel air line .................................. 2
GG* 21813 AN to PTC fitting ....................................................... 2
HH* 21709 Schrader valve with cap & nut .................................. 2
Description ............................................................................ Qty
Standard and metric open-end or box wrenches ...............................Set
9/16" ratchet wrench ............................................................................... 1
Ratchet .................................................................................................... 1
Standard and metric regular and deep-well sockets ...........................Set
Torque wrench ......................................................................................... 1
Die grinder or angle grinder with cut off wheel .......................................1
7/32” hex-key wrench (socket preferable)............................................... 1
Needle nose pliers ...................................................................................1
China marker or equivalent .....................................................................1
Hose cutter, razor blade, or sharp knife .................................................. 1
Hoist or floor jack ....................................................................................1
Safety glasses .........................................................................................1
Safety stands ...........................................................................................2
Black paint or undercoating ...................................................................1
Air compressor or compressed air source ..............................................1
Spray bottle with dish soap/water solution ............................................. 1
Missing or damaged parts? Call Air Lift customer
service at (800) 248-0892 for a replacement part.
Missing or damaged parts? Call Air Lift customer
service at (800) 248-0892 for a replacement part.
* These parts are not shown in the Installation Diagram (Fig. A.1).
LoadLifter 5000 Series
MN-1080
4
C. IntroductionC. IntroductionC. Introduction
The purpose of this publication is to assist with the installation and maintenance of the
LoadLifter 5000 series air spring kits. All LoadLifter 5000 series kits utilize sturdy, reinforced,
commercial-grade single or double, depending on the kit, convolute bellows.
The air springs are manufactured like a tire with layers of rubber and cords that control
growth. LoadLifter 5000 kits provide up to 5,000 pounds (2,268kg) of load-leveling support
with air adjustability from 5-100 PSI (.34-7BAR).
It is important to read and understand the entire installation guide before beginning
installation or performing any maintenance, service or repair.
NOTATION EXPLANATION
Hazard notations appear in various locations in this publication. Information which is
highlighted by one of these notations must be observed to help minimize risk of personal
injury or possible improper installation which may render the vehicle unsafe. Notes are used
to help emphasize areas of procedural importance and provide helpful suggestions. The
following definitions explain the use of these notations as they appear throughout this guide.
INDICATES IMMEDIATE HAZARDS WHICH WILL RESULT IN SEVERE PERSONAL INJURY
OR DEATH.
INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN SEVERE
PERSONAL INJURY OR DEATH.
INDICATES HAZARDS OR UNSAFE PRACTICES WHICH COULD RESULT IN DAMAGE TO
THE MACHINE OR MINOR PERSONAL INJURY.
DANGER
CAUTION
WARNING
PREPARING THE VEHICLE
1. Lift the vehicle and support the frame with safety stands. Leave enough room to drop
the axle down low enough to set the air spring assemblies into position between the
frame and axle. (Fig. D.1).
2. Twist and pull the jounce bumpers to remove them from the mounting cups (Fig. D.2).
3. Strike a line using a china marker or equivalent, on the jounce bumper bracket,
beside and above the bottom of the frame (Fig. D.3). Use a die grinder or angle
grinder with a cut-off wheel to cut along the line on the bracket. Stop slightly short of
the frame.
It may be necessary to grind down some weld if the weld travels under your cut on the
bracket and frame.
DO NOT CUT INTO THE FRAME WITH THE CUT OFF WHEEL. STOP SHORT AND TAP
THE BRACKET WITH A HAMMER FOR FINAL REMOVAL FROM THE FRAME.
LoadLifter 5000 Series
MN-1080
5
D. Installing the LoadLifter 5000 Series System
g. D.2
g. D.1
CAUTION
Cut the jounce bumper
bracket to level above
the bottom of the
frame. Do not cut into
the frame. Passenger’s
(right) side shown.
g. D.3
NOTE
4. Remove the sharp edges with the cut off wheel. Clean and paint the exposed surfaces
of the remainder of the jounce bumper bracket that will be left on the frame (Fig. D.4).
5. The brake line holder that is on the inside of the left side frame, above the axle,
will need to be spaced up to make room for the upper brace (Fig. D.5). Do this by
removing the stock bolt (discard), then insert the spacer (F) between the holder and
bracket; finally attach the line holder back onto the bracket using the M8-1.25 x 35
hex flange bolt (H). Tighten securely.
LoadLifter 5000 Series
MN-1080
6
g. D.4
Remove sharp edges
and paint.
g. D.5
H
F
NOTE
1. Place the roll plates (D) on the air springs (Fig. D.6). Install the elbow swivel air fittings
(J) on the air springs (E). Tighten the air fittings finger-tight plus 1 1/2 turns.
These assemblies will be left- and right-hand specific once assembled.
2. For LoadLifter 5000 Ultimate Plus, install the braided stainless steel air line (DD) (Fig.
D.7). Tighten the air line hex nut finger-tight, then use 2 wrenches to turn 1 additional
flat (1/6 of one full turn). Do not overtighten. For additional information on installing
the braided stainless steel air line, see E. Installing the Air Lines — Installing Braided
Stainless Steel Air Lines.
3. Attach the upper brackets (B) and roll plates with 3/8”-24 x 7/8” hex cap screws (L),
3/8” split lock washers (M) and 3/8” flat washers (N). Leave loose at this time.
4. Attach the roll plate, left-hand lower bracket (A1) and right-hand lower bracket (A2)
with 3/8”-24 x 3/4” flat-head socket cap screws (K) and torque to no more than 20
lb.-ft. (27Nm). Note the orientation of the brackets in Fig. D.6.
LoadLifter 5000 Series
MN-1080
7
ASSEMBLING THE AIR SPRINGS
J
B
N
M
L
D
K
D
E
Driver’s (left) side Passenger’s (right) side
A1
A2
LoadLifter
5000 Ultimate
Plus
For Ultimate
Plus kits, it will
be necessary to
insert the air line
through the slot
while setting the
upper bracket
onto the air spring
assemblies.
g. D.6
Angled flanges
point toward
front of truck
J
DD
The air fitting must be
on the opposite side
of the offset in the
lower brackets.
g. D.7
Front of truck
INSTALLING THE UPPER BRACE
1. Using the 3/8” wire bolt leader tools (O), thread over two 3/8”-16 x 1” carriage bolts
(G) (Fig. D.9).
2. Insert the tools with the carriage bolts, through the two slots using the square hole in
the frame to guide them through (Fig. D.10).
g. D.9
g. D.10
LoadLifter 5000 Series
MN-1080
8
g. D.8
5. Fig. D.8 shows the completed air spring assemblies for LoadLifter 5000 and
LoadLifter 5000 Ultimate kits. LoadLifter Ultimate Plus kits would have the braided
stainless steel air line.
Driver’s (left)
side
Passenger’s
(right) side
O
G
3. Once the carriage bolts are in position, insert the tools through the holes in the brace
(C) (Fig. D.11) and push the brace up against the frame.
4. Carefully remove (twist off) the tool from the top carriage bolt first and install the
3/8”-16 serrated flange nuts (I). Tighten the nuts finger-tight only (Fig. D.12). Carefully
remove the tool from the bottom carriage bolt and repeat. Leave both nuts loose.
Repeat for right side.
INSTALLING THE ASSEMBLIES
1. Index a 3/8”-16 x 1” carriage bolt (G) into the opening on the front of the driver’s (left)
side assembly as shown (Fig. D.13).
2. Drop the axle if not done so already, to gain clearance to put the two assemblies into
position on the axle.
g. D.13
LoadLifter 5000 Series
MN-1080
9
G
g. D.12g. D.11
C
I
3. Set the driver's (left) side assembly into position with the carriage bolt (previously
installed) still in the slot. Set into place on the axle, making sure the back of the
bracket is “hooked” below the jounce bumper strike plate. Push the assembly
forward while lining up the carriage bolt with the existing hole in the front of the lower
jounce bumper strike plate (Figs. D.14 & D.15). Install a 3/8”-16 serrated flange nut (I)
onto the carriage bolt (G), but leave loose at this time.
4. Insert another 3/8” carriage bolt (G) through the corresponding hole in the front side
of the bracket (Fig. D.16).
5. It will be necessary to use a socket with an extension to reach the inside threads on
the carriage bolt previously set into position (Figs. D.17 & D.18) to install the 3/8”-16
serrated flange nut (I). It may be helpful to pull the carriage bolt out slightly so that it
can be angled enough to get the nut started on the threads.
g. D.17
g. D.15g. D.14
g. D.16
I
G
LoadLifter 5000 Series
MN-1080
10
I
g. D.18
Use the slot in the lower control
arm mount for the extension to fit
through while threading the nut
on the bolt.
6. Install the passenger’s (right) side in the same way and torque all of the lower
hardware to 31 lb.-ft. (42Nm).
7. Raise the axle up just enough so that the upper brackets meet the braces. Insert the
3/8”-16 x 1” carriage bolts (G) up through the square holes in the upper brackets and
through the braces (Fig. D.19). Install the 3/8”-16 serrated flange nuts (I) onto the
carriage bolts. Snug the nuts but do not tighten at this time.
It may be helpful to use a pair of needle nose pliers to help guide the carriage bolts into place.
8. Making sure that the upper brackets are flat to the frame (Fig. D.20). Push the upper
assembly forward as far as it can go until the upper brace butts against the jounce
bumper bracket that was left on the frame (Fig. D.21). Torque the frame brace hardware
first, then the upper bracket to brace hardware to 31 lb.-ft. (42Nm).
The lower nut on the frame/brace interface may be hard to get to on the passenger’s (right)
side because of the exhaust, if it is not accessible with the torque wrench and socket, use a
ratcheting wrench and tighten securely.
TECH TIP
g. D.19
g. D.21
NOTE
LoadLifter 5000 Series
MN-1080
11
g. D.20
G
I
9. Raise the axle and remove the safety stands.
10. Adjust the upper air spring assembly so it is as close to perpendicular as possible
to the upper and lower bracket by moving it within the slot in the upper bracket
(Fig. D.22).
11. Tighten the upper bracket/air spring hardware using a 3/8” ratcheting wrench. Since
there is no way to access these bolts with a torque wrench, snug the bolts only. Do
not over tighten.
The air spring assemblies will not be perfectly aligned when complete. This is an acceptable
condition.
g. D.22
NOTE
LoadLifter 5000 Series
MN-1080
12
LoadLifter 5000 Series
MN-1080
13
E. Installing the Air Lines
Air lines are routed from the air springs to Schrader valves. LoadLifter 5000 series air
lines come in two styles: nylon and braided stainless steel. Begin by choosing locations
for the Schrader valves and drill a 5/16” (8mm) hole, if necessary (Fig. E.1).
KEEP AT LEAST 6” (150MM) OF CLEARANCE BETWEEN ALL AIR LINES AND THE
EXHAUST SYSTEM. AVOID SHARP BENDS AND EDGES.
INSTALLING NYLON AIR LINES
1. For nylon air line, it is recommended that the air line be routed along the top of the
frame, forward of the axle, then down to the fitting (Fig. E.2). After cutting the air
line to length, install the air line thermal sleeve over the air line on the passenger’s
(right) side before inserting into the fitting. Secure the air lines to the upper coil spring
mount with zip ties (BB) supplied. Also see Figure E.8.
A. Inside fuel tank filler door C. License plate or
B. Inside rear wheel wells rear bumper area
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
A. B. C.
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
If a location for the Schrader valve other than the back of
the vehicle is chosen, it may be necessary to coil the
excess air line. The braided stainless steel air line cannot
be trimmed.
A. Inside fuel
tank filler
door
B. Inside rear
wheel wells
C. License
plate or rear
bumper area*
* For LoadLifter 5000 Ultimate Plus kits, the recommended location
for the Schrader valves is the rear bumper area or license plate.
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
A.
B.
C.
USE IN
Standard,
Ultimate,
7500XL
USE IN
Plus
upgrade kit
USE IN
Plus combo
manuals
MICHIGAN
XXX-XXX
www.MICHIGAN.gov
If a location for the Schrader valve other than the back of the vehicle is
chosen, it may be necessary to coil the excess air line. The braided
stainless steel air line cannot be trimmed.
USE IN
Plus
upgrade kit
g. E.1
g. E.2
CAUTION
Nylon air line shown
mounted and attached
forward of the axle.
Zip tied to upper spring
mount
Air line thermal sleeve
on passenger’s (right)
side.
LoadLifter 5000 Series
MN-1080
14
NOTE
g. E.5
Good cut Bad cut
Hex nuts
Star washer
Rubber washer
Air Line Setup for Compressor Integration
Air Line Setup Without Compressor System
Vehicle body
or bumper
Hex nuts
Flat washer
Star washer
Rubber washer
Nylon air line
to compressor
system and
Schrader valve
Flat
Flat
Vehicle body
or bumper
Braided stainless steel
air line to air spring
5/16” (8mm)
hole
AN to PTC
fitting
Schrader
valve
Vehicle
body or
bumper
AN
Schrader
valve
Air line hex nut
Flat washer
Nylon air line
to air spring
5/16” (8mm) hole
Braided
stainless
steel air line
to air spring
Hex nuts
Flat washer
Star washer
Rubber washer
Schrader
valve
Vehicle
body or
bumper
Nylon air line
to air spring
5/16” (8mm) hole
g. E.3
g. E.4
2. Cut the air line in half. Make clean, square cuts with a razor blade or hose cutter
(Fig. E.3). Do not use scissors or wire cutters.
3. Use zip ties to secure the air line to fixed points along the chassis. Do not pinch or kink
the air line. The minimum bend radius for the air line is 1
” (25mm)
. Leave at least 2”
(50mm) of slack in the air line to allow for any movement that might pull on the air line.
4. Install the Schrader valve in the chosen location (Fig. E.4).
INSTALLING BRAIDED STAINLESS STEEL AIR LINES
KEEP THE AIR LINE AWAY FROM THE FUEL LINE, BRAKE LINES AND ELECTRICAL
WIRES.
The braided stainless steel air line must be routed to the rear of the vehicle. Install the air line
through one of the openings between the upper coil spring mount and the frame and then
back to the rear where the inflation valves will be mounted (Fig. E.5).
CAUTION
LoadLifter 5000 Series
MN-1080
15
1. Use zip ties to secure the air line to fixed points along the chassis every 6” to 8” (150-
200mm). Leave at least 2” (50mm) of slack to allow for any movement that might pull on
the air line.
2. Tighten the air line hex nut finger-tight, then use 2 wrenches to turn 1 additional flat (1/6
of one full turn). Do not overtighten (Figs. E.6 or E.7). The easiest way to tighten the
fitting is off the vehicle.
Install the Schrader valve in the chosen location.
3. Coil and secure any excess air line in an area where it will not be susceptible to
damage. The braided stainless steel air line cannot be trimmed.
INSTALLING THE HEAT SHIELD
1. Attach the metal heat shield to the exhaust where it is closest to the passenger's
(right) side air spring (Fig. E.8).
Hex nuts
Star washer
Rubber washer
Air Line Setup for Compressor Integration
Air Line Setup Without Compressor System
Vehicle body
or bumper
Hex nuts
Flat washer
Star washer
Rubber washer
Nylon air line
to compressor
system and
Schrader valve
Flat
Flat
Vehicle body
or bumper
Braided stainless steel
air line to air spring
5/16” (8mm)
hole
AN to PTC
fitting
Schrader
valve
Vehicle
body or
bumper
AN
Schrader
valve
Air line hex nut
Flat washer
Nylon air line
to air spring
5/16” (8mm) hole
Braided
stainless
steel air line
to air spring
Hex nuts
Flat washer
Star washer
Rubber washer
Schrader
valve
Vehicle
body or
bumper
Nylon air line
to air spring
5/16” (8mm) hole
g. E.6
g. E.7
g. E.8
Air line
thermal sleeve
1/2” (13mm)
dead air space
between shield
and exhaust
LoadLifter 5000 Series
MN-1080
16
Inside, forward of axle view of
driver’s (left) side installation.
Inside, forward of axle view of
passenger’s (right) side installation.
1. The images show the finished installation of both sides (Figs. F.1, F.2, F.3 & F.4).
F. Finished Installation
g. F.1 g. F.2
Inside, rear of axle view
of passenger’s (right) side
installation.
Inside, over axle view of
passenger’s (right) side
installation.
g. F.3 g. F.4
LoadLifter 5000 Series
MN-1080
17
MAINTENANCE AND USE GUIDELINES
1. Check air pressure weekly.
2. Always maintain normal ride height. Never inflate beyond 100 PSI (7BAR).
3. If the system develops an air leak, use a soapy water solution to check all air line
connections and the inflation valve core before deflating and removing the air spring.
FOR SAFETY AND TO PREVENT POSSIBLE DAMAGE TO THE VEHICLE, DO NOT EXCEED
MAXIMUM GROSS VEHICLE WEIGHT RATING (GVWR) OR PAYLOAD RATING, AS
INDICATED BY THE VEHICLE MANUFACTURER.
ALTHOUGH THE AIR SPRINGS ARE RATED AT A MAXIMUM INFLATION PRESSURE OF
100 PSI (7BAR), THE AIR PRESSURE ACTUALLY NEEDED IS DEPENDENT ON LOAD AND
GROSS VEHICLE WEIGHT RATING.
Maximum Air PressureMinimum Recommended Pressure
100 PSI (7BAR)5 PSI (.34BAR)
LIMITED WARRANTY AND RETURN POLICY
Air Lift Company provides a limited lifetime warranty to the original purchaser of its load support
products, that the products will be free from defects in workmanship and materials when used
on cars and trucks as specified by Air Lift Company and under normal operating conditions,
subject to the requirements and exclusions set forth in the full Limited Warranty and Return
Policy that is available at www.airliftcompany.com/warranty.
For additional warranty information contact Air Lift Company customer service.
CAUTION
CAUTION
INSTALLATION CHECKLISTINSTALLATION CHECKLIST
Clearance test — Inflate the air springs to 40-60 PSI (2.8-4.1BAR) and make sure
there is at least 1/2” (13mm) clearance from anything that might rub against each
sleeve. Be sure to check the tire, brakes, frame, shock absorbers and brake cables.
Leak test before road test — Inflate the air springs to 40-60 PSI (2.8-4.1BAR) and
check all connections for leaks. All leaks must be eliminated before the vehicle is
road tested.
Heat test — Be sure there is sufficient clearance from heat sources, at least 6” (152mm)
for air springs and air lines. If a heat shield was included in the kit, install it. If there is no
heat shield, but one is required, call Air Lift customer service at (800) 248-0892.
Fastener test — Recheck all bolts for proper torque.
Road test — The vehicle should be road tested after the preceding tests. Inflate the
air springs to recommended driving pressures. Drive the vehicle 10 miles (16km) and
recheck for clearance, loose fasteners and air leaks.
Operating instructions — If professionally installed, the installer should review the
operating instructions with the owner. Be sure to provide the owner with all of the
paperwork that came with the kit.
INSTALLATION CHECKLIST
Need Help?
Contact Air Lift Company customer service department by calling (800)
248-0892.
For calls from outside the USA or Canada,
dial (517) 322-2144.
Need Help?
Contact Air Lift Company Customer Service at (800) 248-0892
or email service@airliftcompany.com.
For calls outside the U.S. or Canada, dial (517) 322-2144.
JJC-0919
Thank you for purchasing Air Lift Products — the Authorized Installer's choice!
Air Lift Company • 2727 Snow Road • Lansing, MI 48917 or P.O. Box 80167 • Lansing, MI 48908-0167
Printed in the USA
California: WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
Air Lift Company reserves the right to make changes and improvements to its products and publications at any time.
For the latest version of this manual, contact Air Lift Company at (800) 248-0892 or visit airliftcompany.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Air Lift 94375 Installation guide

Air Lift
Brand
Air Lift
Model
94375
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents