Steering Damper kit for Aprilia RSV Mille R
SD 175
Mounting Instructions
Note!1
Please note that there can be small differences
between your product and the images in
these instructions.
Note!1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not
cause damage to the product, wipe off the
excessive oil or grease with a cloth.
Note!1
Before you install this product, check the kit
contents. If anything is missing, please contact
an Öhlins dealer.
Warning!⚠
Before you install this product, read the Öhlins
Owner’s manual. This product is an important
part of the vehicle and the vehicle stability.
Kit Contents
Description Part No Pcs
Steering damper SD175 1
Bolt M6x16 01046-01 1
Bolt M6x25 01046-17 1
Plastic washer 02259-02 1
Spacer 02258-01 2
Öhlins sticker 00192-01 2
Sticker 00194-10 2
Owners Manual 07261-02 1
Kit content
Description Pcs. Part No.
Steering damper SD 175
Bolt M6x16 1 01046-01
Bolt M6x25 1 01046-17
Plastic washer 1 02259-02
Spacer 2 02258-01
Sticker Öhlins Racing AB 2 00192-01
Sticker 2 00194-10
Owners Manual 1
Set-up data
Stroke 65 mm
Recommended set-up 10 clicks from closed
Mounting
Instructions
Öhlins steering damper kit SD 175
for Aprilia RSV Mille R
Notes
SD 175, Issued 04 03 18
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00, fax +46 8 590 025 80.
E-mail: [email protected]
www.ohlins.com
2
1
Put the motorcycle on a work stand so that the
rear wheel barely touches the ground.
2
Mount the Öhlins steering damper in the
already made mounting points on the lower
triple clamp and under the air intake in front of
the steering head.
3
Recommended adjustment of steering damper
is 10 clicks from closed position.
Note!1
Check for clearance when turning to full stops.
Caution!✋
Make sure that you tighten all screws to the
correct torque and that nothing fouls or restricts
movement of the shock absorber/front fork/
steering damper when the suspension is fully
compressed or extended.
4
Continue your work according to the Owners
Manual, section Adjustments.
MOUNTING INSTRUCTIONS
Warning!⚠
We strongly recommend to let an Öhlins dealer
install this product.
Warning!⚠
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note!1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note!1
Before you install this product clean the vehicle.
Before you start
WARNING!
1. Installing a steering damper,
that is not approved by the
vehicle manufacturer, may
affect the stability of your
vehicle. Öhlins Racing AB can-
not be held responsible for any
personal injury or damage
whatsoever that may occur
after fitting the steering
damper. Contact an Öhlins
dealer or other qualified person
for advice.
2. Please study and make
certain that you fully under-
stand all the mounting instruc-
tions and the owner´s manuals
before handling this steering
damper kit. If you have any
questions regarding proper
installation procedures,
contact an Öhlins dealer or
other qualified person.
3. The vehicle service manual
must be referred to when
installing the Öhlins steering
damper.
WARNING!
Failure to follow warning
instructions could result in
severe or fatal injury to
anyone working with,
inspecting or using the
steering damper, or to
bystanders.
Kit contents
Before installing the sreering
damper, please check the
contents of the kit, listed on the
front page of this instruction. If
anything is missing, contact
your Öhlins dealer.
Öhlins Racing AB can not be
held responsible for any
damage whatsoever to shock
absorber or vehicle, or injury to
persons, if the instructions for
fitting and maintenance are
not followed exactly. Similarly,
the warranty will become null
and void if the instructions are
not adhered to.
NOTE!
During storage and transporta-
tion, especially at high ambient
temperature, the oil and grease
used for assembling may run
out inside the packing and
damage the expanded
polystyrene packing material.
This is not unusual and is in no
way detrimental to the steering
damper.
Öhlins products are subject to
continual improvement and
development. Consequently,
although these instructions
include the most up-to-date
information available at the
time of printing, there may be
minor differences between
your steering damper and this
manual. Please consult your
Öhlins dealer if you have any
questions with regard to the
contents of the manual.
Safety signals
Important information con-
cerning safety is distin-
guished in this manual by the
following notations.
The Safety alert symbol
means:
Caution! Your safety is
involved.
© Öhlins Racing AB.
All rights reserved.
Any reprinting or unauthorized
use without the written
permission of Öhlins Racing
AB is prohibited.
Printed in Sweden.
CAUTION!
Caution indicates that spe-
cial precautions must be
taken to avoid damage to the
steering damper.
NOTE!
This indicates information
that is of importance with
regard to procedures.
WARNING!
1. It´s advisable to have an
Öhlins dealer or other qualified
person to fit your steering
damper.
2. Instructions in the vehicle
service manual are to be
followed when changing the
shock absorber.
3. When working on a lifted
vehicle it must be securely
supported to prevent it from
falling.
Mounting Instructions
1
Put the motorcycle on a stand
and make sure it‘s steadily fixed
so it will not fall over.
2
Mount the Öhlins steering
damper in the already made
mounting points on the lower
triple clamp and under the air
intake in font of the steering
head.
NOTE!
Check for clearance when
turning to full stops.
3
Recommended adjustment of
steering damper is 10 clicks
from closed position.
NOTE!
Make sure that all bolts are
tightened to the correct torque
and that nothing fouls or
restricts movement of the steer-
ing damper when the suspen-
sion is being fully compressed
or extended.
4
Continue your work according
to the Owners Manual, section
Adjustments.
NOTE!
It is necessary to check the
tightening torque of all bolts
regularly.
NOTE!
The motorcycle should at no
times be driven with the steer-
ing damper at full close posi-
tion.
End eye to be
attached to
the right side
of the lower
triple clamp.
Spacer
Plastic washer
Spacer
Bolt M6x25
Bolt M6x16
Lower triple
clamp
3
MOUNTING INSTRUCTIONS
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SETUP DATA
Warning!⚠
Before you ride/drive, always make sure that the
setup is according to the recommended setup
data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make
any adjustments. Contact an Öhlins dealer if
you have any questions about setting up.
ADJUSTMENTS
Part no. MI_SD175_1
Issued 2016-03-14
Stroke 65 mm
Rec. Set-up 10 clicks
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ohlins 21400-xx Mounting Instruction
-
-
-
-
-
-
-
-
-