Blueprint Lighting Campana Installation guide

Type
Installation guide

Blueprint Lighting Campana is a versatile lighting fixture designed to provide ambient light in residential and commercial spaces. Crafted from high-quality materials, it boasts a canopy, crossbar, slip ring, stem, and fixture body. Installation is straightforward, involving feeding fixture wires through various components, securing them to a junction box, and connecting wires. The fixture accommodates G9 bi-pin LED bulbs and glass globes, offering warm and inviting illumination.

Blueprint Lighting Campana is a versatile lighting fixture designed to provide ambient light in residential and commercial spaces. Crafted from high-quality materials, it boasts a canopy, crossbar, slip ring, stem, and fixture body. Installation is straightforward, involving feeding fixture wires through various components, securing them to a junction box, and connecting wires. The fixture accommodates G9 bi-pin LED bulbs and glass globes, offering warm and inviting illumination.

212-243-6300
315 W 39th St.
New York, NY 10018
Ceiling Fixture Installation Instructions
stem
2x #8-32 screws
3x wire nuts
crossbar
fixture body
canopy
slip ring
Ceiling Fixtures / Contents
212-243-6300
315 W 39th St.
New York, NY 10018
Ceiling Fixture Installation Instructions
1. Feed the fixture wires through the stem-nipple assembly as shown. Thread the stem-nipple
assembly into the top of fixture until the stem is flush. Tighten the set screw from the side.
stem
nipple
fixture wires
set screwtop of fixture
212-243-6300
315 W 39th St.
New York, NY 10018
Ceiling Fixture Installation Instructions
2. Slide the slip ring and canopy down over the stem, resting them on the top of the fixture below.
Make sure the slip ring set screw is slightly loosened to not scratch the stem as it is lowered.
3. Feed the fixture wires through the crossbar-nipple assembly. Thread the crossbar-nipple assembly
into the top of the stem until the stem and crossbar are flush.
crossbar
nipple
canopy
slip ring
stem
fixture wires
212-243-6300
315 W 39th St.
New York, NY 10018
Ceiling Fixture Installation Instructions
4. Hold the crossbar close to the ceiling and connect the fixture ground wire to the ceiling ground
wire.
5. Mount the crossbar to the junction box using the x2 provided #8-32 screws.
6. Connect the +/- fixture wires to the +/- ceiling wires.
fixture ground wire
#8-32 screws
crossbar
wire nuts
fixture wires
ceiling wires
212-243-6300
315 W 39th St.
New York, NY 10018
Ceiling Fixture Installation Instructions
7. Raise the canopy and slip ring up until the canopy is flush to the ceiling. Tighten the slip ring set
screw to lock the slip ring and canopy in place.
canopy
slip ring
stem
212-243-6300
315 W 39th St.
New York, NY 10018
Ceiling Fixture Installation Instructions
8. For glass globe installation (if applicable), Insert G9 bi pin LED bulbs into the sockets and then install
the glass globes by threading them onto the G9 threaded sockets.
G9 threaded
socket
G9 bi pin
LED bulb Glass Globe
with female G9
threaded insert
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Blueprint Lighting Campana Installation guide

Type
Installation guide

Blueprint Lighting Campana is a versatile lighting fixture designed to provide ambient light in residential and commercial spaces. Crafted from high-quality materials, it boasts a canopy, crossbar, slip ring, stem, and fixture body. Installation is straightforward, involving feeding fixture wires through various components, securing them to a junction box, and connecting wires. The fixture accommodates G9 bi-pin LED bulbs and glass globes, offering warm and inviting illumination.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI