Watts BT-WR02 User guide

Watts
Brand
Watts
Model
BT-WR02
Type
User guide

Watts BT-WR02 is a wireless thermostat that offers precise temperature control, energy-saving features, and flexible scheduling options for your home's heating and cooling system. Program up to 4 daily events to match your unique comfort preferences and save energy when you're away. The large, backlit display ensures easy reading even in low-light conditions, while the intuitive interface makes programming a breeze. Plus, with its wireless design, you can place the thermostat anywhere in your home for optimal temperature control.

Watts BT-WR02 is a wireless thermostat that offers precise temperature control, energy-saving features, and flexible scheduling options for your home's heating and cooling system. Program up to 4 daily events to match your unique comfort preferences and save energy when you're away. The large, backlit display ensures easy reading even in low-light conditions, while the intuitive interface makes programming a breeze. Plus, with its wireless design, you can place the thermostat anywhere in your home for optimal temperature control.

USER GUIDE GB
1 channel RF Receiver 230Vac (EFHRFR 001)
TECHNICAL CHARACTERISTICS
MODES DESCRIPTION
- Radio frequency RF receiver (868 Mhz).
- Personal code on each product.
- Equipped with a push button to select AUTO, MANUAL or RF INIT
mode.
- To be used only with ours thermostats.
LED INDICATOR
PPL IMP 2362A
RADIO CONFIGURATION MODE
1. Install and plug the Receiver. Then press the Receiver push button during 4
seconds, the Green LED should lit up indicating that the Receiver is now in radio
configuration mode waiting for a thermostat configuration address.
2. Please refer to the thermostat leaflet for enter the thermostat in “RF Init” mode.
3. Verify that radio signals are correctly received by the Receiver. On the Receiver,
the Green LED should blink at each radio signal received from the thermostat.
4. Exit the Radio configuration mode on the thermostat. (Please refer to the
thermostat leaflet)
5. Now starting up your installation in AUTO mode..
Yellow Red Green
0 0 0
Automatic mode, HEATER stopped
0 1 0 Automatic mode, HEATER operating
1 0 0
Manual mode OFF forced
1 1 0 Manuel mode HEATER forced
0 or 1 0 or 1 quick flash Reception of an order, 4 flash
0 or 1 0 or 1 1 Waiting for a configuration signal (cf. configuration)
0 0 slow blink ERROR see repair sequence bellow:
Repair instructions
- Verify the emitter batteries.
- Verify the emitter/receiver range.
- No perturbation by an apparatus at less than 50cm of
the receiver.
- No perturbation by an apparatus on the 868 MHz
frequency (continuous transmission).
By pressing on the push
button
nothing happens
- Verify that the receiver is correctly connected
- Verify main power supply (230VAC)
Manual Mode LED.
(Yellow)
Heating LED.
(Red)
RF LED.
(Green)
Mode push button
AUTO Mode
Manual Mode
(Heater forced)
Manual Mode
(Stop forced)
Press button
during 4sec
Press button
Press button
Press button RF init
Press button
Operating temperature 0°C - 50°C (32°F – 122°F)
Electrical
Protection Class II - IP44
Power Supply 230Vac 50Hz
Radio frequency and
Receiving zone
868 MHz, <10mW.
Range of approximately 100m in open space.
Range of approximately 30m in residential environment.
certifications CE. EN 300220-1, EN 301489-1
(Radio frequency certifications)
Output Relay 12A 250Vac
BEDIENUNGSANLEITUNG
D
FUNK-INITIALISERUNG (Funk-Paarung)
Einzel Funk-Empfängereinheit 230Vac (EFHRFR 001)
TECHNISCHE DATEN
BETRIEBSARTEN
- Funk-Empfängereinheit (868 MHz)
- Eigene, unverwechselbare Verschlüsselung bei jedem Produkt
-Mit Mode Taste für AUTO, HAND- oder FUNK-
INITIALISIERUNGSMODUS
-Einsatz nur in Verbindung mit einem Funk-Thermostaten dieser
Baureihe
LED ANZEIGE
Handbetrieb LED.
(Gelb)
Heizen LED.
(Rot)
Funk LED.
(Grün)
Gelb Rot Grün
0 0 0 Automatisch, Heizung inaktiv
0 1 0 Automatisch, Heizung aktiv
1 0 0
Manuell, Heizung inaktiv
1 1 0 Manuell, Heizung aktiv
0 oder
1
0 oder
1 schnell blinkend Erhalten einer Anforderung.
0 oder
1
0 oder
1 1 Warten auf Konfigurationssignal (siehe
Konfiguration)
0 0 langsam blinkend FEHLER siehe Reparaturanleitung unten:
Reparaturanleitung
- Batterien des Empfängers prüfen
- Reichweite von Sender und Empfänger
prüfen
- Störungen durch Geräte in weniger als 50 cm
Entfernung vom Empfänger?
- Störung durch Geräte auf der Frequenz 868
MHz (dauerhafte Übertragung)?
Keine Reaktion nach Drücken des
Hand-Knopfs
- Korrekten Anschluss des Empfängers prüfen
- Netzspannung von 230 V/AC prüfen
Betriebstemperatur 0°C - 50°C (32°F – 122°F)
Schutzart Schutzklasse II - IP 44
Betriebsspannung 230Vac 50Hz
Funk Frequenz und
Empfangsbereich
868 MHz, <10mW.
Funk-Reichweite offene Distanz: ca. 100 m.
Funk-Reichweite in Gebäuden: ca. 30 m
Zulassungen CE. EN 300220-1, EN 301489-1
(Radio frequency certifications)
Schaltleistung Relais 12A 250Vac
Mode Taste
AUTO Mode
Handbetrieb
(Heizen)
Manual Mode
(Stop Modus)
Taste 4 sec.
drücken
Taste drücken
Taste drücken
Taste drücken RF init
Taste drücken
1. Versorgen Sie den Funk-Empfänger mit Netzspannung. Drücken Sie die Mode Taste
für ca. 4 Sek. Die grüne LED sollte aufleuchten. Der Empfänger befindet sich nun im
Funk-Initialisierungsmodus und ist für bereit für die Paarung mit dem Funk-Thermostat.
2. Bitte beachten Sie die Bedienungsanleitung des Funk-Thermostaten und bringen Sie
diesen in den Modus Funk-Konfiguration (Funk-Paarung).
3. Stellen Sie sicher, dass der Funk-Empfänger das Funk-Signal korrekt erhalten hat. Am
Empfänger sollte die grüne LED beim Empfang eines Funk-Signals blinken.
4. Verlassen Sie die Funk-Konfiguration am Thermostaten. (Bitte die entsprechende
Bedienungsanleitung beachten).
5. Betreiben Sie die Anlage im Autobetrieb
  • Page 1 1
  • Page 2 2

Watts BT-WR02 User guide

Watts
Brand
Watts
Model
BT-WR02
Type
User guide

Watts BT-WR02 is a wireless thermostat that offers precise temperature control, energy-saving features, and flexible scheduling options for your home's heating and cooling system. Program up to 4 daily events to match your unique comfort preferences and save energy when you're away. The large, backlit display ensures easy reading even in low-light conditions, while the intuitive interface makes programming a breeze. Plus, with its wireless design, you can place the thermostat anywhere in your home for optimal temperature control.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Other documents