VonHaus 3500087 User manual

Type
User manual
LONG REACH
PAINT ROLLER
3500087 - Instruction Manual
01 0818
CONTENTS
Safety Instructions 1
Specification 2
Assembly 3
Assembly 4
Usage 5
Cleaning & Maintenance 6
Cleaning & Maintenance 7
Hints & Tips, Surface Preparation 8
Troubleshooting 9
Warranty 10
WARNING
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE
1
INTENDED USE.
Only use the Paint Roller as described in
this instruction manual.
This Paint Roller it is not suitable for
industrial or commercial use.
The use of any accessory or attachment
or performance of any operation with this
product other than those recommended
in this instruction manual may present a
risk of personal injury and/or damage to
property.
This Paint Roller is not intended for
use by persons with reduced physical,
sensory or mental capabilities, or lack
of experience and knowledge, unless
they have been given supervision or
instructions concerning use of the
product by a person responsible for their
safety.
Children should be supervised to ensure
they do not play with the product.
WORK AREA SAFETY.
Keep your work area clean and well lit.
Cluttered or dark areas invite accidents.
Always ensure there is adequate
ventilation when painting.
We also recommend wearing goggles
and overalls.
You must clean the Paint Roller Barrel
thoroughly after each use.
STORAGE & MAINTENANCE.
Store the product out of reach of children
and do not allow persons unfamiliar
with the product or these instructions to
operate the product.
The following safety symbols may
appear on this product. Please ensure
you understand their meanings before
operating the Paint Roller in order
to prevent personal injury and avoid
damage to the tool.
SAFETY SYMBOLS
WARNING! Pay
attention to all
safety and
guidance
Read manual
before use
Wear eye
protection
SPECIFICATION
1. ROLLER FRAME & COLLAR.
2. BARREL COLLAR.
3. ROLLER BARREL.
4. SPLATTER SHIELD.
5. PLUNGER.
6. PAINT TUBE/HANDLE.
7. FRAME CONNECTOR.
1
5
6
8
9
10
11
12
13
14
2
3
4
8. FILL TUBE CONNECTOR.
9. FLOOR STAND.
10. PAINT CAN CLIP.
11. FILL TUBE.
12. TUBE EXTENSION RIBS.
13. DUCK VALVE.
14. FILL TUBE COLLAR.
15. PETROLEUM JELLY (not pictured).
7
ROLLER BARREL IS SUPPLIED ALREADY
ASSEMBLED.
ASSEMBLY
Connect the ROLLER BARREL to the
ROLLER FRAME and secure with the
BARREL COLLAR by turning clockwise.
Secure the FLOOR STAND into the small
openings at the base of the PAINT TUBE/
HANDLE.
Insert the ROLLER FRAME into the end
of the PAINT TUBE as shown. Secure by
turning the COLLAR clockwise.
Clip the SPLATTER SHIELD into the end of
the ROLLER BARREL and onto the ROLLER
FRAME.
3
1 2
3 4
ASSEMBLY
Insert the DUCK VALVE into the centre of
the FILL TUBE COLLAR as shown.
Clip the FILL TUBE to the PAINT CAN CLIP
ensuring the ring (circled) sits behind the
arm. This will prevent the FILL TUBE being
lifted out of the paint during the extraction
process.
With the PAINT CAN CLIP and FILL TUBE
assembled, this can now be inserted and
connected to the desired paint can.
Screw the FILL TUBE COLLAR and DUCK
VALVE to the base of the PAINT TUBE.
5
78
6
NOTE: For deeper paint containers, we recommend you attach a piece of plastic tubing or
hose (38.1mm in diameter) to the end of the FILL TUBE.
USAGE
5
IMPORTANT: Before use, it is important that both the FILL TUBE nozzle and DUCK VALVE
are lubricated with the PETROLEUM JELLY. This will prevent any air being withdrawn into the
paint tube.
IMPORTANT: Pump the plunger downwards slightly to inject the paint into the PAINT
BARREL before withdrawing more paint. Repeat this process several time to prime the
PAINT BARREL before first use.
Place the FILL TUBE COLLAR over the FILL
TUBE nozzle and firmly push down until fully
inserted. This is easier when held at a 45˚ angle.
Holding the PAINT TUBE with one hand,
hold the PLUNGER with the other and slowly
withdraw. DO NOT exceed the MAX volume
(0.52L)
To remove the PAINT TUBE from the FILL
TUBE nozzle, firmly hold the top of the PAINT
CAN CLIP as shown and pull the PAINT TUBE
away.
Sit the Paint Roller down on a dust sheet or
newspaper using the FLOOR STAND before
you are ready to begin painting or during
breaks.
ENSURE FILL
TUBE AND
UNIT ARE
COMPLETELY
STRAIGHT.
CLEANING & MAINTENANCE
With the ROLLER BARREL removed, fill a
bucket or large container with warm, soapy
water.
Attach the PAINT CAN CLIP/FILL TUBE to
the bucket or container and insert the nozzle
into the PAINT TUBE.
Extract the soapy water by pulling the
PLUNGER so all of the water is inside the
PAINT TUBE.
Pump all of the water back out of the PAINT
TUBE and into the bucket or container.
REPEAT this process around 5 times until the
PAINT TUBE is clean.
NOTE: You may wish to dispose of the dirty
water after 2 pumps and replace with warm
and soapy clean water to aid the removal of
paint.
Remove the ROLLER FRAME and immerse
the PAINT TUBE in a fresh bucket of warm,
soapy water.
As in the previous step, pull back the
PLUNGER and pump the warm water in and
out of the PAINT TUBE to clean.
Repeat 4-5 times until the water remains clear.
Disassemble the FILL TUBE COLLAR and
DUCK VALVE at the base of the PAINT TUBE
ready for cleaning as shown below.
Wash the removable components in warm,
soapy water and scrub clean with a soft
sponge.
Completely dry the DUCK VALVE & FILL
TUBE COLLAR before re-coating with a thin
layer of the PETROLEUM JELLY supplied.
CLEANING & MAINTENANCE
Using a pair of pliers (not supplied) pull out the centre of the ROLLER BARREL and end cap.
Wash all of these components in warm soapy water until they are completely clear of any paint
residue.
Soak up any moisture using a towel and leave the Paint Roller sponge to completely dry before
reassembling.
Remove the PLUNGER from the PAINT TUBE and wipe away any excess water.
When the PLUNGER is completely dry, apply a new layer of PETROLEUM JELLY around the rubber
seal rings using your finger and insert the PLUNGER back into the PAINT TUBE.
Secure into position using the locking ring.
7
IMPORTANT: DO NOT dispose of the end cap or the centre of the ROLLER BARREL.
These are needed when purchasing new replacement accessories.
Only use the perforated Paint Roller (spares available online). Standard Rollers will not work.
Inspect the Paint roller for lint before painting, if needed, wash and dry before use.
When using the Long Reach Paint Roller for the first application, it will take most of the paint in the
PAINT TUBE to saturate the Roller. A second fill of the PAINT TUBE may be needed.
Ensure you keep the Roller moving when applying pressure on the PLUNGER to prevent any
dripping.
If the Paint Roller starts to slide along the walls, remove any pressure from the PLUNGER. This
indicates too much paint has been inserted into the ROLLER BARREL.
When painting in tight spaces, partially fill the PAINT TUBE as this will reduce the overall length of
the Paint Roller making it easier to handle.
When leaving the Long Reach Paint Roller unattended for a long period of time, wrap the ROLLER
BARREL in cling film or a bag to prevent it from drying out.
Ensure the type of paint being used can be cleaned using mineral spirits or warm water. Avoid using
any gloss pains as this will easily block the PAINT TUBE.
Always protect you floor surfaces by placing dust sheets down before painting.
If you are using the FLOOR STAND, ensure all pressure has been removed from the PLUNGER to
prevent any paint from dripping.
HINTS & TIPS
SURFACE PREPARATION
With any paint task, you should always ensure that you have prepared your surface to get the best finish.
You must ensure all surfaces are free from dust, dirt, rust and grease. Lightly pressure wash decks or exterior
surfaces and ensure they are completely dry before painting.
With pre-coated or pre-painted surfaces, lightly rub down with sandpaper to ensure a good bond for the paint.
With bare wood surfaces, wipe with a damp rag to ensure the surface is free of dust.
NOTE: Allow to dry completely before painting
TROUBLESHOOTING
PROBLEM SOLUTION
PAINT TAKES TOO LONG TO
APPEAR ON THE SURFACE.
AIR IS DRAWN INTO THE
PAINT TUBE.
PAINT IS LEAKING OUT OF
THE ENDS OF THE PAINT
ROLLER.
PLUNGER IS DIFFICULT TO
PUSH AND PULL.
FILL TUBE IS DIFFICULT IN
INSERT/REMOVE.
If you are having difficulty using this product and require support, please
The PAINT TUBE may require a second fill
with paint. The ROLLER BARREL takes time to
saturate.
Ensure the FILL TUBE and PAINT TUBE are
clear or any blockages that may prevent any
paint being withdrawn and dispensed.
Ensure PETROLEUM JELLY has been applied
to the end of the PLUNGER, DUCK VALVE and
FILL TUBE COLLAR before use.
Be sure the FILL TUBE has been fully inserted
into the FILL TUBE COLLAR when extracting
paint.
The end cap needs to be securely attached to
the end of the ROLLER BARREL after being
cleaned or replaced. Ensure it clicks into place
when attached.
The BARREL COLLAR may be loose. Follow the
assembly instructions on page 3 for guidance.
Lubrication is required. Use the PETROLEUM
JELLY around the seal rings located at the end
of the PLUNGER.
Lubrication is required. Use the PETROLEUM
JELLY around the FILL TUBE COLLAR if
required.
9
DISPOSAL INFORMATION
COPYRIGHT
WARRANTY
Please recycle where facilities exist. Check with your local authority for recycling advice.
All material in this instruction manual are copyrighted by DOMU Brands.
Any unauthorised use may violate worldwide copyright, trademark, and other laws.
To register your product and find out if you qualify for a free extended warranty please go to
www.Vonhaus.com/Warranty.
Please retain a proof of purchase receipt or statement as proof of the purchase date.
The warranty only applies if the product is used solely in the manner indicated in the Warnings page of this
manual, and all other instructions have been followed accurately. Any abuse of the product or the manner in
which it is used will invalidate the warranty.
Returned goods will not be accepted unless re-packaged in its original packaging and accompanied by a
relevant and completed returns form. This does not affect your statutory rights.
No rights are given under this warranty to a person acquiring the appliance second-hand or for commercial or
communal use.
Thank you for purchasing the Long Reach Paint Roller.
VonHaus® is a registered trademark of DOMU Brands Ltd
Made in China for DOMU Brands Ltd M24 2RW
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

VonHaus 3500087 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI