Black and Decker RapidRoller BDPR400 User manual

INSTRUCTION

MANUAL

See inside this instruction manual for complete instructions.

Lire le mode d’emploi pour connaître les directives en entier.

Consulte el interior de este manual de instrucciones para ver las

instrucciones completas.

Catalog Number BDPR400

QUICK START GUIDE

Push roller assembly over roller

frame until it snaps into place.

Thread handle collar on roller frame.

Snap paint can cover onto paint

can. (See “Filling RAPIDROLLER”

section if cover does not fit.)

Push fill valve down over fill tube

until orange cap is completely

covered.

Adjust roller head to desired angle. Begin rolling on wall and push plunger

to fill head and roller with paint.

Squeeze trigger for additional paint.

Insert fill tube into paint can cover.

Thank you for choosing Black & Decker! Go to

www.BlackandDecker.com/NewOwner to register your new product.

If you have a question or experience a problem with your Black & Decker purchase,

go to HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS for instant answers 24 hours a day.

If you can’t find the answer or do not have access to the internet, call 1-800-544-6986 from 8 a.m. to 5 p.m.

EST Mon. -- Fri. to speak with an agent. Please have the catalog number available when you call.

RAPIDROLLER

T

M

Squeeze trigger to free up the

plunger. Pull back plunger to draw

paint. (May take some force).

WARNING: To reduce the risk of injury, user must read and understand the instruction manual before using the RAPIDROLLER

TM

WARNING: Some paints contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. To

reduce your exposure wear appropriate safety equipment such as face masks, gloves, and other appropriate protective equipment. Please review

and follow the safety precautions on the paint container.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING

PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in

property damage.

WARNING:

• Do not use RAPIDROLLER

T

M

for purposes other than described in this manual. Failure to do so may result in injury to persons and or property

damage.

• For use only with water soluble and most oil based paints and stains. Not for use with oil based paints and stains that require cleaning solutions

stronger than mineral spirits (refer to label on original paint container). Do not use with paint removers, or the like. Liquids other than paint or

stain may damage product and result in injury to persons or property damage.

• Read the label on the original paint container and follow all directions. Failure to do so may result in injury to persons or property damage.

• Use proper eye protection and other safety equipment for skin and respiratory protection when mixing the paint, and when filling, using, and

cleaning the product. Paint and its fumes can cause personal injury.

• To reduce the risk of injury, use only in a well ventilated area.

• Thoroughly clean and rinse product after using with a particular paint. Mixing different paints in the product may result in property damage.

• To reduce the risk of injury, use only recommended accessories.

• When servicing, use only identical replacement parts. Failure to do so may result in personal injury.

SAVE THESE INSTRUCTIONS

FUNCTIONAL DESCRIPTION

1.)

Plunger

2.) Handle Assembly

3.) O-Rings

4.) Duck Bill Valve

5.)

Wiper Seal

6.) Orange Fill Cap Cover

7.) Roller Frame

8.) Inner End Cap

9.) Roller Core

10.) 3/8 in. perforated roller

11.) Outer End Cap

12.) Spatter Shield

13.) Can Cover

14.) Shroud

15. Fill Tube

16.) Hose Extension Ribs

17.) Petroleum Jelly

PETROLEUM JELLY

LA GELEE DE PETROLE

LA JALEA DE PETROLEO

2

1

3

4

5

6

7

8

9

10

11

12

13

15

COMPONENTS

16

14

17

2

IMPORTANT SAFETY INSTRUCTIONS

• Only use a perforated roller cover. Standard roller covers will not work.

• Inspect roller cover for lint before painting, if needed wash and dry before using.

• When using the R

APIDROLLER

TM

for the first application, it will take most of the paint in the RAPIDROLLER

TM

t ube to saturate the roller cover. A second

fill may be needed.

• Keep roller moving while pushing plunger in or squeezing trigger to prevent dripping.

• Stop pushing plunger in or squeezing trigger if the roller starts to skid, slide or drip.

• When painting in tight areas partially fill R

APIDROLLER

T

M

or pivot the frame . This reduces its overall length.

• When leaving R

A

PID

RO

LLER

TM

unattended for a longer period of time, wrap roller in a plastic bag to prevent drying, removing as much air as possible

from bag.

• Make sure the type of paint you use can be cleaned with either mineral spirits (for oil-based paints) or a warm water and soap solution (for water

soluble paints like latex).

•

Use drop cloths to protect your floors and anything else in the room that you do not want accidentally splattered with paint.

• When using kickstand, always pivot head to straight position and release pressure by pulling plunger out slightly.

1.) Lubricate part (a) and (b) using petroleum jelly provided. Attach

assembled roller (c) onto R

APIDROLLER

TM

frame (d). Make sure roller

assembly snaps into locking clip on outer end cap.

2.) Push roller frame (a) over end of handle assembly (d) ensuring O-ring

(b) is seated inside roller frame. Thread handle assembly collar (c)

snugly onto threads of roller frame (a).

3.) The spatter shield helps reduce spatter when painting, especially on

ceilings. Position the spatter shield by rotating around roller frame.

NOTE: Spatter shield is also helpful to prevent dripping when

R

APIDROLLER

TM

is resting on kickstand and is not in use. Just position

spatter shield under roller.

1.) Insert the small end of the fill tube (a) through the hole in the bottom

side of the paint can cover (b).

Push in until tight and to the ridge of the fill tube.

2.) Snap paint can cover onto paint can (fig. E). Lubricate top of fill tube

stem with a small amount of petroleum jelly included in carton.

NOTE: The can cover will not fit on some paint containers. It can be

stretched over larger cans or compressed slightly by squeezing to fit

smaller cans.

To fill the R

APIDROLLER

TM

when the can cover does not fit your paint

container, omit the can cover and place fill tube directly into container.

Hold the fill tube with hand to stabilize as needed.

A fill tube can clip is available as an optional accessory for use with other

size containers. See “Accessories”.

For deeper containers like 5 gallon pails, fit a section of ¾ inch I.D. (inner

diameter) clear tubing over the ribs of the fill tube to extend it

(fig. E1) and clip to side of pail with fill tube can clip. Cut bottom end of

tubing at slight angle. Tubing is available at most hardware stores.

3

Tips for painting with the RAPIDROLLER

T

M

Preparing the RAPIDROLLER

T

M

to paint

A

B

d

a

b

c

C

c

d

a

b

Filling the RAPIDROLLER

TM

with paint

D

a

b

E

E1

3.) Hold the RAPIDROLLER

T

M

at a 45 degree angle and place the fill valve (a) over the fill tube. Gently push the RAPIDROLLER

T

M

down until it bottoms

on the fill tube. MAKE SURE THE ORANGE FILL CAP COVER (a) IS COMPLETELY COVERED BY SHROUD OF CAN COVER.

NOTE: Remove cardboard spacer, and squeeze trigger to free up the plunger.

Pull plunger (b) all the way back to draw paint into R

APIDROLLER

TM

. (This may take some force.) Once tube

is full you are ready to start painting. Lift RAPIDROLLER

TM

slowly off fill tube.

N

OTE: If you do not receive a complete fill the first time, push plunger slowly to return paint to can and

t

hen pull back plunger making sure angle is correct and orange fill cap cover is fully seated.

1.) Begin rolling on wall and push plunger handle or squeeze trigger to feed paint into the roller cover.

NOTE: Initial saturation of the roller may require the full amount of paint from the first fill. Fill

R

APIDROLLER

TM

as needed.

H

ELPFUL HINTS

• The trigger only needs to be squeezed when paint is needed.

• If you are getting a dot pattern when painting, apply more paint.

• If the roller is sliding on the surface, apply less paint.

• You may notice petroleum jelly within the handle. This is necessary and will help in its operation and will

not affect the paint.

2.) The roller head can be adjusted to three different angles. Press the orange button on the

roller head to change the angle from straight to 40 or 80 degrees. Use straight on for

general painting and 40 or 80 degree angles for hard to reach places or when painting

close to ceiling or edging (fig. H).

NOTE: The handle (a) can be rotated to make it more comfortable when painting with an

angled roller frame.

To rotate handle to desired position, loosen collar (b), adjust handle and retighten collar

(fig H1).

3.) When not in use rest theR

APIDROLLER

TM

on the convenient kickstand (a).

• When using kickstand, R

APIDROLLER

TM

should always be on a drop cloth (b) or over newspaper in case of drips.

• When painting, kickstand should be pointed away from roller to avoid getting spatter on kickstand.

• Always rotate roller to the straight position before pacing on kickstand.

• To prevent drips, relieve pressure on R

APIDROLLER

TM

by pulling plunger out slightly.

NOTE: Attaching the spatter guard when using the kickstand helps insure that any dripping paint is contained.

1.) Pull plunger back to draw excess paint from roller frame into tube.

HINT: Place thumb over orange fill cap cover (a) to help remove the most

paint from the frame prior to pulling back plunger.

4

F

Painting with the RAPIDROLLER

T

M

a

b

G

I

a

b

J

H

a

b

H1

Cleaning the RAPIDROLLER

TM

a

K

2.) Return paint from RA

PID

RO

LLER

TM

to can by holding RA

PID

RO

LLER

TM

at a 45

degree angle and pushing fill valve onto fill tube until it bottoms on fill

tube. Make sure orange fill valve is completely covered by shroud of can

lid. Push plunger in until it stops.

3.) Scrape excess paint into can from roller.

Remove the roller by grasping the outer end cap and the roller frame and

using your thumb on the opposite hand to push the roller off as shown.

HINT: Wear disposable gloves or use a plastic bag over roller to keep

your hands clean.

4.) Remove the inner end cap by inserting the metal tube of the roller frame

into the cap about 1 inch and at an angle. Pull the roller frame gently

towards you (fig. N).

Remove the roller core. Empty any remaining paint.

Remove the outer cap by inserting the roller frame into the roller and

gently pushing the cap off (fig. O).

1.) Remove the fill tube from the paint can lid and push

it directly into the fill valve. When cleaning water soluble paints, submerge the fill tube into warm, soapy

water and pull the plunger in and out 5 or more times. When using oil based paints, instead of water, use

proper cleaning solvent listed on manufacturers container and dispose of properly.

HINT: Use a sink, a wash tub, or any container that will hold water to perform above flushing process.

Replace water when dirty or when moving to the next step.

2.) Remove the fill tube. Then submerge the roller frame, and ensuring the fill valve is also

under water, pull the plunger in and out 5 or more times (fig. Q).

HINT: When using a small container, pivot the roller frame to the 80 degree position to fit

inside container (fig. Q1).

3.) Remove roller frame and continue cleaning as needed. Submerge the handle in the warm, soapy

water and pull the plunger in and out 5 or more times.

HINT: Wipe off remaining paint from the end of plunger (a).

5

M

L

N

O

P

Q

Q1

Cleaning the RAPIDROLLER

TM

R

a

6

4.) Unthread valve cap and remove wiper seal and duck bill valve to clean.

Rinse all remaining parts and drain all fluid from the RAPIDROLLER

TM

.

5.) Remove tubing from frame (if needed) by pinching hose clamps. Flush

frame and tubing. Replace tubing and secure with hose clamps.

6.) Always purchase a perforated roller cover. A standard roller will not

work.

Lubrication helps with normal operation and should be done after cleaning and before each use.

1.) Turn the threaded assembly collar (a) near the trigger counterclockwise until the main

tube assembly slides off.

NOTE: When reassembling, black threaded collar (a) should be towards trigger handle.

2.) Apply petroleum jelly around and in between the rubber seals shown. Reassemble making sure the

rubber seals are not twisted or damaged. Tighten the locking collar.

3.) Apply petroleum jelly to the duck bill valve and wiper seal and replace within unit threading the

valve cap back into place.

4.) Apply petroleum jelly to the inner seals on the end caps (c & d) then

assemble the roller by placing the core (a) inside of roller cover (b) and

attaching end caps and as shown.

S

S1

Lubricating the RAPIDROLLER

TM

V

T

U

a

d

b

c

W

7

Troubleshooting

PROBLEM SOLUTION

Takes a long time for paint to appear on surface. See first note on “Painting with the RAPIDROLLER

TM

”. May take a

second fill.

Air is drawn into handle instead of paint. Slowly push handle in to expel air. Remove and reinsert product on

fill tube. Be sure fill tube is fully seated in valve body. If necessary,

apply petroleum jelly to fill tube which makes it easier to seat fill tube

and valve body.

Make sure O-ring is in place between handle assembly and roller

frame and well lubricated.

Difficult to insert or remove fill tube from valve. Put petroleum jelly in fill port opening and or fill tube.

Handle is difficult to move in and out. Lubricate rubber seals at end of plunger, or twist plunger slightly to

break seal.

Paint leaks out end cap. Make sure both end caps are pushed snugly into and are even with

the end of roller cover. If they are OK, remove end caps, clean out

any old paint and relubricate with petroleum jelly.

Paint leaks out of fill valve. Lubricate valve with petroleum jelly.

Make sure wiper seal is in place.

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or

call the BLACK & DECKER help line at 1-800-544-6986.

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool

service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location

nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or

visit www.blackanddecker.com

Warranty

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product

will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the

store is a participating retailer). Returns should be made within the time period of the retailerʼs policy for exchanges (usually 30 to 90

days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns

that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or

replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed

under "Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary

from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker

Service Center. This product is not intended for commercial use.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country

specific warranty information contained in the packaging, call the local company or see the website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free

replacement.

Accessories

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Recommended accessories for use with your RAPIDROLLER

TM

are available from your local dealer or authorized service center.

If you need assistance regarding accessories, please call: 1-800-544-6986

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

F

ill tube can clip - for use with containers which do not fit the round can cover provided. Available through a

Black & Decker Service Center.

When using larger containers such as a five gallon bucket, use the fill tube can clip with a length of 3/4 inch

I.D. tubing available at most large home centers. The tubing fits over the ribbed end of the fill tube.

Perforated roller sleeves are available at hardware stores.

Page is loading ...

Black and Decker RapidRoller BDPR400, BDPR400 User manual

Related papers

Other documents