Fujitsu ASMA13BETA Installation guide

Brand: Fujitsu

Model: ASMA13BETA

Category: Split-system air conditioners

Type: Installation guide

En-1

1. SAFETY PRECAUTIONS

• Read carefully all of safety information written in this manual before you install or use the

air conditioner.

• The warnings and precautions indicated in this manual contain important information

pertaining to your safety. Be sure to observe them.

• Hand this manual, together with the operating manual, to the customer. Request the

customer to keep them on hand for future use, such as for relocating or repairing the

unit.

WARNING

Indicates a potentially or imminently hazardous situation which, if

not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or

moderate injury or damage to property.

WARNING

To avoid getting an electric shock, never touch the electrical components soon after the

power supply has been turned off. After turning off the power, always wait 10 minutes or

more before you touch the electrical components..

Installation of this product must be done by experienced service technicians or

professional installers only in accordance with this manual. Installation by non-

professional or improper installation of the product might cause serious accidents such

as injury, water leakage, electric shock, or ﬁ re. If the product is installed in disregard of

the instructions in this manual, it will void the manufacturer’s warranty.

Do not turn on the power until all work has been completed. Turning on the power

before the work is completed can cause serious accidents such as an electric shock or

a ﬁ re.

If refrigerant leaks when you are working, ventilate the area. If the leaking refrigerant is

exposed to a direct ﬂ ame, it may produce a toxic gas.

Installation must be performed in accordance with regulations, codes, or standards for

electrical wiring and equipment in each country, region, or the installation place.

Do not use this equipment with air or any other unspeciﬁ ed refrigerant in the refrigerant

lines. Excess pressure can cause a rupture.

During installation, make sure that the refrigerant pipe is attached ﬁ rmly before you

run the compressor. Do not operate the compressor under the condition of refrigerant

piping not attached properly with 2-way or 3-way valve open. This may cause abnormal

pressure in the refrigeration cycle that leads to rupture and even injury.

When installing or relocating the air conditioner, do not mix gases other than the

speciﬁ ed refrigerant (R32) to enter the refrigerant cycle.

If air or other gas enters the refrigerant cycle, the pressure inside the cycle will rise to

an abnormally high value and cause rupture, injury, etc.

For appropriate working of the air conditioner, install it as written in this manual.

To connect indoor unit and outdoor unit, or indoor unit and branch box, use air

conditioner piping and cables available through your local distributor. This manual

describes proper connections using such installation set.

Do not modify power cable, use extension cable or branch wiring. Improper use may

cause electric shock or ﬁ re by poor connection, insufﬁ cient insulation or over current.

Do not purge the air with refrigerants but use a vacuum pump to vacuum the

installation.

There is no extra refrigerant in the outdoor unit for air purging.

Do not use means to accelerate the defrosting process or to clean, other than those

recommended by the manufacturer.

The appliance shall be stored in a room without continuously operating ignition sources

(for example: open ﬂ ames, an operating gas appliance or an operating electric heater.

Do not pierce or burn.

Be aware that refrigerants may not contain an odour.

Using the same vacuum pump for different refrigerants may damage the vacuum pump

or the unit.

Use a clean gauge manifold, vacuum pump and charging hose for R32 or R410A

exclusively.

WARNING

Do not modify this unit, such as opening a hole in the cabinet.

During the pump-down operation, make sure that the compressor is turned off before

you remove the refrigerant piping.

Do not remove the connection pipe while the compressor is in operation with 2 way or 3

way valve open. This may cause abnormal pressure in the refrigeration cycle that leads

to rupture and even injury.

CAUTION

This unit must be installed by qualiﬁ ed personnel with a capacity certiﬁ cation of handling

refrigerant ﬂ uids. Refer to regulation and laws in use on installation place.

Install the unit by following local codes and regulations in force at the place of

installation, and the instructions provided by the manufacturer.

This unit is part of a set constituting an air conditioner. The unit must not be installed

alone or be installed with non-authorized device by the manufacturer.

When installing pipes shorter than 3 m, sound of the outdoor unit will be transferred to

the indoor unit, which will cause large operating sound or some abnormal sound.

To protect the persons, earth( ground) the unit correctly, and use the power cable

combined with an Earth Leakage Circuit Breaker (ELCB).

The units are not explosion proof, and therefore should not be installed in explosive

atmosphere.

This unit contains no user-serviceable parts. Always consult experienced service

technicians for repairing.

When moving or relocating the air conditioner, consult experienced service technicians

for disconnection and reinstallation of the unit.

Children should be monitored to ensure they do not play with the device.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety. Children should be supervised to ensure that they do

not play with the appliance.

Do not touch the aluminum ﬁ ns of heat exchanger built-in the indoor or outdoor unit to

avoid personal injury when you install or maintain the unit.

Do not place any other electrical products or household belongings under indoor unit or

outdoor unit. Condensation dripping from the unit might get them wet, and may cause

damage or malfunction of your property.

Precautions for using R32 refrigerant

The basic installation work procedures are the same as conventional refrigerant (R410A,

R22) models.

However, pay careful attention to the following points:

WARNING

Since the working pressure is 1.6 times higher than that of refrigerant R22 models,

some of the piping and installation and service tools are special. (See “2.1. Special

tools for R32 (R410A)”.)

Especially, when replacing a refrigerant R22 model with a new refrigerant R32 model,

always replace the conventional piping and ﬂ are nuts with the R32 and R410A piping

and ﬂ are nuts on the outdoor unit side.

For R32 and R410A, the same ﬂ are nut on the outdoor unit side and pipe can be used.

Models that use refrigerant R32 and R410A have a different charging port thread

diameter to prevent erroneous charging with refrigerant R22 and for safety. Therefore,

check beforehand. [The charging port thread diameter for R32 and R410A is 1/2 inch.]

Be more careful than R22 so that foreign matter (oil, water, etc.) does not enter the

piping.

Also, when storing the piping, securely seal the opening by pinching, taping, etc.

(Handling of R32 is similar to R410A.)

AIR CONDITIONER

Wall Mounted Type

INSTALLATION MANUAL

For authorized service personnel only.

PART No.9385991354

Contents

1. SAFETY PRECAUTIONS .......................................................................................... 1

2. ABOUT THIS PRODUCT........................................................................................... 3

3. SELECTING THE MOUNTING POSITION ............................................................... 4

4. INSTALLATION DIAGRAM ........................................................................................ 5

5. INDOOR UNIT INSTALLATION ................................................................................ 5

6. OUTDOOR UNIT INSTALLATION ............................................................................ 7

7. FINISHING................................................................................................................. 8

8. TEST RUN ................................................................................................................. 8

9. CUSTOMER GUIDANCE .......................................................................................... 8

10. FRONT PANEL REMOVAL AND INSTALLATION ..................................................... 8

11. OPTIONAL KIT INSTALLATION ................................................................................ 9

12. PUMP DOWN OPERATION (FORCED COOLING OPERATION) .......................... 10

13. SELECTING THE REMOTE CONTROLLER CUSTOM CODE .............................. 10

14. FUNCTION SETTING.............................................................................................. 10

15. ERROR CODES ...................................................................................................... 12

ไทย

English

IM_01_9385991354-EN.indd 1IM_01_9385991354-EN.indd 1 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-2

CAUTION

1.Installation (Space)

• That the installation of pipe-work shall be kept to a minimum.

• That pipe-work shall be protected from physical damage.

• That compliance with national gas regulations shall be observed.

• That mechanical connections shall be accessible for maintenance purposes.

• In cases that require mechanical ventilation, ventilation openings shall be kept clear

of obstruction.

• When disposing of the product is used, be based on national regulations, properly

processed.

2.Servicing

2-1.Service personnel

• Any person who is involved with working on or breaking into a refrigerant circuit

should hold a current valid certiﬁ cate from an industry-accredited assessment

authority, which authorizes their competence to handle refrigerants safely in accord-

ance with an industry recognised assessment speciﬁ cation.

• Servicing shall only be performed as recommended by the equipment manufacturer.

Maintenance and repair requiring the assistance of other skilled personnel shall be

carried out under the supervision of the person competent in the use of ﬂ ammable

refrigerants.

• Servicing shall be performed only as recommended by the manufacturer.

2-2. Work

• Prior to beginning work on systems containing ﬂ ammable refrigerants, safety

checks are necessary to ensure that the risk of ignition is minimised. For repair to

the refrigerating system, the precautions in 2-2 to 2-8 shall be complied with prior to

conducting work on the system.

• Work shall be undertaken under a controlled procedure so as to minimize the risk of

a ﬂ ammable gas or vapour being present while the work is being performed.

• All maintenance staff and others working in the local area shall be instructed on the

nature of work being carried out.

• Work in conﬁ ned spaces shall be avoided.

• The area around the workspace shall be sectioned off.

• Ensure that the conditions within the area have been made safe by control of ﬂ am-

mable material.

2-3.Checking for presence of refrigerant

• The area shall be checked with an appropriate refrigerant detector prior to and dur-

ing work, to ensure the technician is aware of potentially ﬂ ammable atmospheres.

• Ensure that the leak detection equipment being used is suitable for use with ﬂ am-

mable refrigerants, i.e. non sparking, adequately sealed or intrinsically safe.

2-4.Presence of ﬁ re extinguisher

• If any hot work is to be conducted on the refrigeration equipment or any associated

parts, appropriate ﬁ re extinguishing equipment shall be available at hand.

• Have a dry powder or CO

ﬁ re extinguisher adjacent to the charging area.

2-5.No ignition sources

• No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained ﬂ ammable refrigerant shall

use any sources of ignition in such a manner that it may lead to the risk of ﬁ re or

explosion.

• All possible ignition sources, including cigarette smoking, should be kept sufﬁ ciently

far away from the site of installation, repairing, removing and disposal, during which

ﬂ ammable refrigerant can possibly be released to the surrounding space.

• Prior to work taking place, the area around the equipment is to be surveyed to make

sure that there are no ﬂ ammable hazards or ignition risks. “No Smoking” signs shall

be displayed.

2-6.Ventilated area

• Ensure that the area is in the open or that it is adequately ventilated before breaking

into the system or conducting any hot work.

• A degree of ventilation shall continue during the period that the work is carried out.

• The ventilation should safely disperse any released refrigerant and preferably expel

it externally into the atmosphere.

2-7. Checks to the refrigeration equipment

• Where electrical components are being changed, they shall be ﬁ t for the purpose

and to the correct speciﬁ cation.

• At all times the manufacturer’s maintenance and service guidelines shall be fol-

lowed.

• If in doubt consult the manufacturer’s technical department for assistance.

• The following checks shall be applied to installations using ﬂ ammable refrigerants.

- The charge size is in accordance with the room size within which the refrigerant

containing parts are installed.

- The ventilation machinery and outlets are operating adequately and are not

obstructed.

- If an indirect refrigerating circuit is being used, the secondary circuit shall be

checked for the presence of refrigerant.

- Marking to the equipment continues to be visible and legible. Markings and signs

that are illegible shall be corrected.

- Refrigeration pipe or components are installed in a position where they are

unlikely to be exposed to any substance which may corrode refrigerant contain-

ing components, unless the components are constructed of materials which are

inherently resistant to being corroded or are suitably protected against being so

corroded.

2-8. Checks to electrical devices

• Repair and maintenance to electrical components shall include initial safety checks

and component inspection procedures.

• If a fault exists that could compromise safety, then no electrical supply shall be con-

nected to the circuit until it is satisfactorily dealt with.

• If the fault cannot be corrected immediately but it is necessary to continue opera-

tion, an adequate temporary solution shall be used.

• This shall be reported to the owner of the equipment so all parties are advised.

• Initial safety checks shall include.

- That capacitors are discharged: this shall be done in a safe manner to avoid pos-

sibility of sparking.

- That there no live electrical components and wiring are exposed while charging,

recovering or purging the system.

- That there is continuity of earth bonding.

3.Repairs to sealed components

• During repairs to sealed components, all electrical supplies shall be disconnected

from the equipment being worked upon prior to any removal of sealed covers, etc.

• If it is absolutely necessary to have an electrical supply to equipment during servic-

ing, then a permanently operating form of leak detection shall be located at the most

critical point to warn of a potentially hazardous situation.

• Particular attention shall be paid to the following to ensure that by working on elec-

trical components, the casing is not altered in such a way that the level of protection

is affected.

• This shall include damage to cables, excessive number of connections, terminals

not made to original speciﬁ cation, damage to seals, incorrect ﬁ tting of glands, etc.

• Ensure that apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded such that they no longer

serve the purpose of preventing the ingress of ﬂ ammable atmospheres.

• Replacement parts shall be in accordance with the manufacturer’s speciﬁ cations.

NOTE: The use of silicon sealant may inhibit the effectiveness of some types of leak

detection equipment.

Intrinsically safe components do not have to be isolated prior to working on

them.

4.Repair to intrinsically safe components

• Do not apply any permanent inductive or capacitance loads to the circuit without

ensuring that this will not exceed the permissible voltage and current permitted for

the equipment in use.

• Intrinsically safe components are the only types that can be worked on while live in

the presence of a ﬂ ammable atmosphere.

• The test apparatus shall be at the correct rating.

• Replace components only with parts speciﬁ ed by the manufacturer.

• Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

5.Cabling

• Check that cabling will not be subject to wear, corrosion, excessive pressure, vibra-

tion, sharp edges or any other adverse environmental effects.

• The check shall also take into account the effects of aging or continual vibration

from sources such as compressors or fans.

6.Detection of ﬂ ammable refrigerants

• Under no circumstances shall potential sources of ignition be used in the searching

for or detection of refrigerant leaks.

• A halide torch (or any other detector using a naked ﬂ ame) shall not be used.

7.Leak detection methods

• Electronic leak detectors shall be used to detect ﬂ ammable refrigerants, but the

sensitivity may not be adequate, or may need re-calibration. (Detection equipment

shall be calibrated in a refrigerant-free area.)

• Ensure that the detector is not a potential source of ignition and is suitable for the

refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant

and shall be calibrated to the refrigerant employed and the appropriate percentage

of gas (25 % maximum) is conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with most refrigerants but the use of

detergents containing chlorine shall be avoided as the chlorine may react with the

refrigerant and corrode the copper pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be removed/extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall

be recovered from the system, or isolated (by means of shut off valves) in a part of

the system remote from the leak.

Oxygen free nitrogen (OFN) shall then be purged through the system both before

and during the brazing process.

IM_01_9385991354-EN.indd 2IM_01_9385991354-EN.indd 2 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-3

12.Recovery

• When removing refrigerant from a system, either for servicing or decommissioning,

it is recommended good practice that all refrigerants are removed safely.

• When transferring refrigerant into cylinders, ensure that only appropriate refrigerant

recovery cylinders are employed.

• Ensure that the correct number of cylinders for holding the total system charge are

available.

• All cylinders to be used are designated for the recovered refrigerant and labelled for

that refrigerant (i.e. special cylinders for the recovery of refrigerant).

• Cylinders shall be complete with pressure relief valve and associated shut-off valves

in good working order.

• Empty recovery cylinders are evacuated and, if possible, cooled before recovery

occurs.

• The recovery equipment shall be in good working order with a set of instructions

concerning the equipment that is at hand and shall be suitable for the recovery of

ﬂ ammable refrigerants.

• In addition, a set of calibrated weighing scales shall be available and in good work-

ing order.

• Hoses shall be complete with leak-free disconnect couplings and in good condition.

• Before using the recovery machine, check that it is in satisfactory working order, has

been properly maintained and that any associated electrical components are sealed

to prevent ignition in the event of a refrigerant release.

Consult manufacturer if in doubt.

• The recovered refrigerant shall be returned to the refrigerant supplier in the correct

recovery cylinder, and the relevant Waste Transfer Note arranged.

• Do not mix refrigerants in recovery units and especially not in cylinders.

• If compressors or compressor oils are to be removed, ensure that they have been

evacuated to an acceptable level to make certain that ﬂ ammable refrigerant does

not remain within the lubricant.

• The evacuation process shall be carried out prior to returning the compressor to the

suppliers.

• Only electric heating to the compressor body shall be employed to accelerate this

process.

• When oil is drained from a system, it shall be carried out safely.

Explanation of symbols displayed on the indoor unit or outdoor unit.

WARNING

This symbol shows that this equipment uses a ﬂ ammable

refrigerant.

If the refrigerant is leaked, together with an external ignition

source, there is a possibility of ignition.

CAUTION

This symbol shows that the Operation Manual should be

read carefully.

CAUTION

This symbol shows that a service personnel should be

handling this equipment with reference to the Installation

Manual.

CAUTION

This symbol shows that there is information included in the

Operation Manual and/or Installation Manual.

2. ABOUT THIS PRODUCT

2.1. Special tools for R32 (R410A)

Tool name Change from R22 to R32(R410A)

Gauge manifold

Pressure is high and cannot be measured with a conven-

tional (R22) gauge. To prevent erroneous mixing of other

refrigerants, the diameter of each port has been changed.

It is recommended to use gauge with seals -0.1 to 5.3 MPa

(-1 to 53 bar) for high pressure.

-0.1 to 3.8 MPa (-1 to 38 bar) for low pressure.

Charge hose

To increase pressure resistance, the hose material and base

size were changed.(R32/R410A)

Vacuum pump

A conventional vacuum pump can be used by installing a

vacuum pump adapter.

(Use of a vacuum pump with a series motor is prohibited.)

Gas leakage detector

Special gas leakage detector for HFC refrigerant R32 or

R410A.

Copper pipes

It is necessary to use seamless copper pipes and it is desirable that the amount of residual

oil is less than 40 mg/10 m. Do not use copper pipes having a collapsed, deformed or

discolored portion (especially on the interior surface). Otherwise, the expansion value or

capillary tube may become blocked with contaminants.

As an air conditioner using R32(R410A) incurs pressure higher than when using R22, it is

necessary to choose adequate materials.

Thicknesses of copper pipes used with R32(R410A) are as shown in the table below.

Never use copper pipes thinner than 0.8 mm even when it is available on the market.

Thicknesses of Annealed Copper Pipes

Nominal diameter (in.) Outer diameter (mm) Thickness (mm)

1/4 6.35 0.80

3/8 9.52 0.80

8.Removal and evacuation

• When breaking into the refrigerant circuit to make repairs – or for any other

purpose –conventional procedures shall be used.

However, it is important that best practice is followed since ﬂ ammability is a consid-

eration.

The following procedure shall be adhered to:

• remove refrigerant

• purge the circuit with inert gas

• evacuate

• purge again with inert gas

• open the circuit by cutting or brazing

• The refrigerant charge shall be recovered into the correct recovery cylinders.

• The system shall be “ﬂ ushed” with OFN to render the unit safe.

• This process may need to be repeated several times.

• Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and

continuing to ﬁ ll until the working pressure is achieved, then venting to atmosphere,

and ﬁ nally pulling down to a vacuum.

• This process shall be repeated until no refrigerant is within the system.

• When the ﬁ nal OFN charge is used, the system shall be vented down to atmos-

pheric pressure to enable work to take place.

• This operation is absolutely vital if brazing operations on the pipe work are to take

place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and

there is ventilation available.

9.Charging procedures

• In addition to conventional charging procedures, the following requirements shall be

followed.

- Ensure that contamination of different refrigerants does not occur when using

charging equipment.

- Hoses or lines shall be as short as possible to minimize the amount of refrigerant

contained in them.

- Cylinders shall be kept upright.

- Ensure that the refrigeration system is earthed prior to charging the system with

refrigerant.

- Label the system when charging is complete (if not already).

- Extreme care shall be taken not to overﬁ ll the refrigeration system.

• Prior to recharging the system it shall be pressure tested with OFN.

• The system shall be leak tested on completion of charging but prior to commission-

ing.

• A follow up leak test shall be carried out prior to leaving the site.

10.Decommissioning

• Before carrying out this procedure, it is essential that the technician is completely

familiar with the equipment and all its details.

• It is recommended good practice that all refrigerants are recovered safely.

• Prior to the task being carried out, an oil and refrigerant sample shall be taken in

case analysis is required prior to re-use of reclaimed refrigerant.

• It is essential that electrical power is available before the task is commenced.

a) Become familiar with the equipment and its operation.

b) Isolate system electrically.

c) Before attempting the procedure ensure that:

• mechanical handling equipment is available, if required, for handling refriger-

ant cylinders;

• all personal protective equipment is available and being used correctly;

• the recovery process is supervised at all times by a competent person;

• recovery equipment and cylinders conform to the appropriate standards.

d) Pump down refrigerant system, if possible.

e) If a vacuum is not possible, make a manifold so that refrigerant can be removed

from various parts of the system.

f) Make sure that cylinder is situated on the scales before recovery takes place.

g) Start the recovery machine and operate in accordance with manufacturer’s

instructions.

h) Do not overﬁ ll cylinders. (No more than 80 % volume liquid charge).

i) Do not exceed the maximum working pressure of the cylinder, even temporarily.

j) When the cylinders have been ﬁ lled correctly and the process completed, make

sure that the cylinders and the equipment are removed from site promptly and

all isolation valves on the equipment are closed off.

k) Recovered refrigerant shall not be charged into another refrigeration system

unless it has been cleaned and checked.

11.Labelling

• Equipment shall be labelled stating that it has been de-commissioned and emptied

of refrigerant.

• The label shall be dated and signed.

• Ensure that there are labels on the equipment stating the equipment contains ﬂ am-

mable refrigerant.

IM_01_9385991354-EN.indd 3IM_01_9385991354-EN.indd 3 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-4

WARNING

To install a unit that uses R32 refrigerant, use dedicated tools and piping materials

that have been manufactured speciﬁ cally for R32(R410A) use. Because the pressure

of R32 refrigerant is approximately 1.6 times higher than R22, failure to use dedicated

piping material or improper installation can cause rupture or injury. Furthermore, it can

cause serious accidents such as water leakage, electric shock, or ﬁ re.

Do not use a vacuum pump or refrigerant recovery tools with a series motor, since it

may ignite.

2.2. Power

WARNING

Always use a special branch circuit and install a special receptacle to supply power to

the room air conditioner.

Use a circuit breaker and receptacle matched to the capacity of the air conditioner.

Install a leakage circuit breaker in accordance with the related laws and regulations and

electric company standards.

The circuit breaker is installed in the permanent wiring. Always use a circuit that can trip

all the poles of the wiring and has an isolation distance of at least 3 mm between the

contacts of each pole.

CAUTION

The power source capacity must be the sum of the air conditioner current and

the current of other electrical appliances. When the current contracted capacity is

insufﬁ cient, change the contracted capacity.

When the voltage is low and the air conditioner is difﬁ cult to start, contact the power

company the voltage raised.

2.3. Electric requirement

CAUTION

Be sure to install a breaker of the speciﬁ ed capacity.

Regulation of cables and breaker differs from each locality, refer in accordance with

local rules.

Voltage rating

1 ø 220 V (50 Hz)

Operating range

198-242 V

Cable

Conductor

size [mm

]

Type Remarks

Power supply cable 1.5 Type 60245 IEC57

2cable + Earth (Ground),

1ø220-230-240V

Connection cable 1.5 Type 60245 IEC57

3cable + Earth (Ground),

1ø220-230-240V

Selected sample: Select the correct cable type and size according to the country or

region’s regulations.

Max. wire length: Set a length so that the voltage drop is less than 2%. Increase the

wire diameter when the wire length is long.

Breaker Speciﬁ cation

Circuit breaker

(over current)

Current : 10(A)

Earth leakage breaker Leakage current : 30mA 0.1sec or less

Select the appropriate breaker of the described specification according to the national

or regional standards.

Select the breaker that enough load current can pass through it.

• Before starting work check that power is not being supplied to all poles of the indoor

unit and outdoor unit.

• Install all electrical works in accordance to the national standard.

• Install the disconnect device with a contact gap of at least 3 mm in all poles nearby the

units. (Both indoor unit and outdoor unit)

• Install the circuit breaker nearby the units.

2.4. Pipe length

Maximum length

Maximum height

(between indoor and outdoor)

15m 5m

CAUTION

If the units are further apart than the maximum length of the piping is speciﬁ ed, correct

operation can not be guaranteed.

The outdoor unit with the refrigerant removed from the packaging is sealed.

(Indoor unit, the refrigerant is not sealed.)

2.5. Additional charge

For the additional amount, see the table below.

Pipe length

7.5 m 15 m Rate

Additional refrigerant

None +120 g 16 g/m

Maximum amount of refrigerant charge

770 g

2.6. Operating range

Cooling mode

Dry mode

Outdoor temperature 21 to 46 ˚C

2.7. Accessories

The following installation accessories are supplied.

Use them as required.

Name and Shape Q’ty Name and Shape Q’ty Name and Shape Q’ty

Operating manual

Installation manual

(This manual)

Wall hook bracket

Remote controller

holder

Battery

Tapping screw

(M4 × 20 mm)

Cloth tape

Tapping screw

(M3 × 12 mm)

Insulation (Drain hose)

The following items are necessary to install this air conditioner. (The items are not included

with the air conditioner and must be purchased separately.)

Name Q’ty Name Q’ty

Connection pipe assembly 1 Wall cap 1

Connection cable 1 Saddle 1 set

Wall pipe 1 Drain hose 1

Decorative tape 1 Tapping screws 1 set

Vinyl tape 1 Sealant 1

2.8. Optional parts

Refer to each installation manual for the method of installing optional parts.

Parts name Model No. Application

Wired Remote Controller UTY-RNN*M For air conditioner operation

Apple-catechin ﬁ lter UTR-FA13-1

Ion deodorization ﬁ lter UTR-FA13-2

3. SELECTING THE MOUNTING POSITION

Decide the mounting position with the customer as follows:

• Do not set to a place where there is oily smoke, oil is used in the factory, the unit can

contact sea breeze, sulﬁ de gases will be generated in the hot spring area, corrosive

gases will be generated, animal may urine on the unit and ammonia will be generated

and a dusty place.

Indoor unit

(1) Install the indoor unit level on a strong wall which is not subject to vibration.

(2) The inlet and outlet ports should not be obstructed : the air should be able to blow all

over the room.

(3) Install the unit a dedicated electrical branch circuit.

(4) Do not install the unit where it will be exposed to direct sunlight.

(5) Install the unit where connection to the outdoor unit is easy.

(6) Install the unit where the drain hose can be easily installed.

(7) Take servicing, etc. into consideration and leave the spaces shown in “4. INSTALLA-

TION DIAGRAM”. Also install the unit where the ﬁ lter can be removed.

(8) Indoor unit should be set to a place where it is free from the inﬂ uence of the electronic

instant on/off type ﬂ uorescent lamp and the thin TV screen.

Correct initial installation location is important because it is difﬁ cult to move unit after it is

installed.

IM_01_9385991354-EN.indd 4IM_01_9385991354-EN.indd 4 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-5

5. INDOOR UNIT INSTALLATION

WARNING

During transportation or relocation of the indoor unit, pipes shall be covered with the

wall hook bracket for protection. Do not move the product by holding the indoor unit

pipes.

(When operating, There is a possibility that the stress is applied to the pipe joint, ﬂ am-

mable gas may leak.)

Indoor unit piping direction

The piping can be connected in

the 3 directions indicated in the

following.

When the piping is connected in

direction 2 or 3 , cut along the

piping groove in the side of

the front cover with a hacksaw.

2: Right

outlet

3: Bottom

outlet

1: Rear

outlet

(Rear)

Cutting the hole in the wall for the connecting piping

(1) Cut a 80 mm diameter hole in the wall at the position shown in the following.

(2) When cutting the wall hole at the inside of the wall hook bracket, cut the hole to a point

of intersection of centering marks.

When cutting the wall hole at the outside of the wall hook bracket, cut the hole at a

point of 10 mm below.

(3) Cut the hole so that the outside end is lower (5 to 10 mm) than the inside end.

(4) Always align the center of the wall hole. If misaligned, water leakage will occur.

(5) Cut the wall pipe to match the wall thickness, stick it into the wall cap, fasten the cap

with vinyl tape, and stick the pipe through the hole.

(6) For left piping and right piping, cut the hole a little lower so that drain water will ﬂ ow

freely.

Wall hook bracket

Lower

Centring marks

80 mm hole

10 mm

or over

Fasten with vinyl tape

5 to

10 mm

low

Wall pipe*

Wall cap*

(Inside) (Outside)

Wall

*Field supplied

WARNING

Always use the wall pipe. If the wall pipe is not used, the cable that is connected

between the indoor unit and the outdoor unit may touch metal, and cause an electric

discharge.

Installing the wall hook bracket

Wall hook bracket

Tapping screw (large)

(Accessory, 8 pcs)

(1) Install the wall hook bracket so that it

is correctly positioned horizontally and

vertically.

If the wall hook bracket is titled, water

will drip to the ﬂ oor.

(2) Install the wall hook bracket so that

it is strong enough to support the

weight of the unit.

• Fasten the wall hook bracket to the wall with 6 or more screws through the holes near

the outer edge of the bracket.

• Check that there is no rattle at the wall hook bracket.

CAUTION

Install the wall hook bracket both horizontally and vertically aligned. Misaligned

installation may cause water leakage.

Forming the drain hose and pipe

[Rear piping, Right piping, Bottom piping]

Pipe (top)

Indoor unit

drain hose

(bottom)

• Install the indoor unit piping in the direction

of the wall hole and bind the drain hose and

pipe together with vinyl tape.

• Install the piping so that the drain hose is at

the bottom.

• Wrap the pipe of the indoor unit that visible

from the outside with decorative tape.

• For right or bottom outlet piping, cut off the

piping outlet cutting groove with a hacksaw.

CAUTION

Install heat insulation around both the gas and liquid pipes. Failure to do so may cause

water leaks.

Use heat insulation with heat resistance above 120 °C. Reverse cycle model only.

In addition, if the humidity level at the installation location of the refrigerant piping is

expected to exceed 70%, install heat insulation around the refrigerant piping. If the

expected humidity level is 70-80%, use heat insulation that is 15 mm or thicker and if

the expected humidity exceeds 80%, use heat insulation that is 20 mm or thicker.

If heat insulation is used that is not as thick as speciﬁ ed, condensation may form on

the surface of the insulation. In addition, use heat insulation with heat conductivity of

0.045 W/(m•K) or less (at 20 °C).

Outdoor unit

(1) If possible, do not install the unit where it will be exposed to direct sunlight.

(If necessary, Install a blind that does not interfere with the air ﬂ ow.)

(2) Do not install the unit where a strong wind blows or where it is very dusty.

(3) Do not install the unit where people pass.

(4) Take your neighbors into consideration so that they are not disturbed by air blowing

into their windows or by noise.

(5) Provide the space shown in “4. INSTALLATION DIAGRAM” so that the air ﬂ ow is not

blocked.

Also for efﬁ cient operation, leave open three of the four directions front, rear, and both

sides.

(6) Install the unit where keep away more than 3m from the antenna of TV set and Radio.

(7) Outdoor unit should be set to a place where both drainage and itself will not be

affected when heating.

WARNING

Install the unit where is capable to support the weight of the unit. Secure the unit ﬁ rmly

so that the unit does not topple or fall.

CAUTION

Do not install the unit in the following areas:

• Area with high salt content, such as at the seaside. It will deteriorate metal parts,

causing the parts to fail or the unit to leak water.

• Area ﬁ lled with mineral oil or containing a large amount of splashed oil or steam,

such as a kitchen. It will deteriorate plastic parts, causing the parts to fail or the unit

to leak water.

• Area where is close to heat sources.

• Area that generates substances that adversely affect the equipment, such as sulfuric

gas, chlorine gas, acid, or alkali.

It will cause the copper pipes and brazed joints to corrode, which can cause refriger-

ant leakage.

• Area that can cause combustible gas to leak, contains suspended carbon ﬁ bers or

ﬂ ammable dust, or volatile inﬂ ammables such as paint thinner or gasoline.

• If gas leaks and settles around the unit, it can cause a ﬁ re.

• Area where animals may urinate on the unit or ammonia may be generated.

• Do not use the unit for special purposes, such as storing food, raising animals, grow-

ing plants, or preserving precision devices or art objects. It can degrade the quality of

the preserved or stored objects.

• Install the unit where drainage does not cause any trouble.

• Install the indoor unit, outdoor unit, and power supply cable at least 1 m away from a

television or radio receivers. The purpose of this is to prevent TV reception interfer-

ence or radio noise.

(Even if they are installed more than 1 m apart, you could still receive noise under

some signal conditions.)

• If children may approach the unit, take preventive measures so that they cannot

reach the unit.

• Install the indoor unit on the wall where the height from the ﬂ oor is more than 1.8 m.

4. INSTALLATION DIAGRAM

Installation dimensions

Wall hook bracket

6 cm or over

5 cm or over

[INDOOR UNIT]

[OUTDOOR UNIT]

150 cm or over

180 cm or over

9 cm or over

(Wall cap)

Remote

controller

10 cm or over

60 cm or over

25 cm or

over

10 cm or over

20 cm or

over

5 cm or over

48 cm

27 cm

Remote controller holder

The ﬂ are connection

part should be installed

outdoors.

Tapping screw (small)

IM_01_9385991354-EN.indd 5IM_01_9385991354-EN.indd 5 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-6

[For Left rear piping (Drain hose), Left piping (Drain hose)]

Interchange the drain cap and the drain hose.

For left piping, cut off the piping

outlet cutting groove with a

hacksaw.

Remove the drain cap by pulling

the projection at the end of the

cap with pliers, etc.

Drain cap

Indoor unit drain hose

* The drain caps have 2 shapes. (The shapes are different

according to the model.)

For the B-type drain cap, use a pair of cutting pliers or

similar tool to pull off the projection on the tip of the cap.

Drain cap

Insert the drain cap

until it butts against

the drain port.

No gap

Hexagonal

wrench

Drain cock

Drain cap

Use a hexagonal wrench (4 mm at

opposite side) to insert the drain cap

until it contacts the tip of drain cock.

Drain hose

Insert the drain hose until it

butts against the drain port.

• After passing the indoor piping and drain

hose through the wall hole, hang the

indoor unit on the hooks at the top and

bottom of the wall hook bracket.

[Installing the indoor unit]

Indoor unit

(Fitting)

Bottom hooks

Wall hook

bracket

Top hooks

• Hang the indoor unit

from the hooks at the

top of the wall hook

bracket.

Indoor unit

(Spacer)

Wall hook bracket

• Insert the spacer, etc. between the indoor unit and the

wall hook bracket and separate the bottom of the indoor

unit from the wall.

• After hooking the indoor unit to the top hook, hook the ﬁ ttings

of the indoor unit to the two bottom hooks while lowering the

unit and pushing it against the wall.

CAUTION

• Insert drain hose and drain cap securely. Drain should slope down to avoid water

leakage.

• When inserting the drain hose, no other material than water should be applied.

Application of other material than water will cause deterioration of the hose, and may

cause water leakage.

• After you remove a drain hose, be sure to attach the drain cap.

• When you secure the piping and drain hose with tape, arrange the drain hose so that

it comes under bottom of piping.

• For drain hose piping in low temperature environment, you need to apply frozen

protection to prevent a frozen drain hose. After cooling operation is performed in low

temperature environment, (when outdoor temperature under 0 °C,) water in the drain

hose could be frozen. Frozen drain water will block the water ﬂ ow in the hose, and

may cause water leakage at the indoor unit.

Flare connection (Pipe connection)

Flaring

(1) Cut the connection pipe to the necessary length with a pipe cutter.

(2) Hold the pipe downward so that cuttings will not enter the pipe and remove the burrs.

(3) Insert the ﬂ are nut onto the pipe and ﬂ are the pipe with a ﬂ aring tool.

Insert the ﬂ are nut (always use the ﬂ are nut

attached to the indoor and outdoor units

respectively) onto the pipe and perform the ﬂ are

processing with a ﬂ are tool.

Use the special R410A ﬂ are tool, or the

conventional (for R22) ﬂ are tool.

When using the conventional ﬂ are tool, always

use an allowance adjustment gauge and secure

the A dimension shown in the table below.

Check if [L] is

ﬂ ared uniformly

and is not cracked

or scratched.

Pipe

Die

Pipe outside diameter

Pipe outside

diameter

A (mm)

Flare tool for R410A

Clutch type

Conventional (R22) ﬂ are tool

Clutch type Wing nut type

ø 6.35 mm (1/4”) 0 to 0.5 1.0 to 1.5 1.5 to 2.0

ø 9.52 mm (3/8”) 0 to 0.5 1.0 to 1.5 1.5 to 2.0

Connection

(1) Install the outdoor unit wall cap (supplied with

the optional installation set or procured at the

site) to the wall pipe.

(2) Connect the outdoor unit and indoor unit

piping.

(3) After matching the center of the ﬂ are surface

and tightening the nut hand tight, tighten the

nut to the speciﬁ ed tightening torque below

with a torque wrench.

Tighten with two wrenches.

Wrench (ﬁ xed)

Flare nut

Connection pipe

Indoor unit pipe

Torque

wrench

Flare nut size and tightening torque

To prevent

gas leakage,

coat the ﬂ are

surface with

refrigerator oil.

Flare nut [mm (in.)] Tightening torque [N•m (kgf•cm)]

6.35 (1/4) dia. 16 to 18 (160 to 180)

9.52 (3/8) dia. 32 to 42 (320 to 420)

CAUTION

• Fasten a ﬂ are nut with a torque wrench as instructed in this manual. If fastened too

tight, the ﬂ are nut may be broken after a long period of time and cause a leakage of

refrigerant.

HOW TO CONNECT THE WIRE TO THE TERMINALS

(1) Use ring terminals with insulating sleeves as shown in the ﬁ gure below to connect to

the terminal block.

(2) Securely crimp the ring terminals to the wires using an appropriate tool so that the

wires do not come loose.

(3) Use the speciﬁ ed wires, connect them securely, and fasten them so that there is no

stress placed on the terminals.

(4) Use an appropriate screwdriver to tighten the terminal screws. Do not use a

screwdriver that is too small, otherwise, the screw heads may be damaged and

prevent the screws from being properly tightened.

(5) Do not tighten the terminal screws too much, otherwise, the screws may break.

(6) See the table below for the terminal screw tightening torques.

Tightening torque

M3.5 screw 0.8 to 1.0 N • m ( 8 to 10 kgf • cm )

M4 screw 1.2 to 1.8 N • m (12 to 18 kgf • cm)

M5 screw 2.0 to 3.0 N • m (20 to 30 kgf • cm)

Screw with special washer

Ring terminal

Terminal board

Terminal block

Wire

Sleeve

Ring terminal

Wire

Strip

10 mm

Indoor unit wiring

(1) Open the intake grille. Remove the tapping screw for the wire cover and remove the

wire cover.

Screw

Wire cover

IM_01_9385991354-EN.indd 6IM_01_9385991354-EN.indd 6 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-7

(2) Remove the tapping screw and while minding the cable clamp hook, remove the cable

clamp.

Screw

Cable clamp

Cable

clamp

Hook

(3) Connect the end of the connection cable fully into the terminal block.

12 3 4 5 6

Terminal block

Earth screw

Cable clamp

Connection cable

25 mm

35 mm

CAUTION

• Match the terminal block numbers and connection cable colors with those of the

outdoor unit. Incorrect wiring may cause a ﬁ re.

• When ﬁ xing the connection cable with the cable clamp, always fasten the cable at the

plastic jacket portion, but not at the insulator portion. If the insulator is chafed, electric

leakage may occur.

• Always connect the earth (ground) wire. Improper earthing (grounding) work can

cause electric shocks.

• Connect the connection cables ﬁ rmly to the terminal block. Imperfect installation may

cause a ﬁ re.

• Do not use the ground screw for the indoor unit to the outdoor unit unless it is

speciﬁ ed.

6. OUTDOOR UNIT INSTALLATION

Switch cover

Hook

Screw

• Set the unit on a strong stand, such as one made of

concrete blocks to minimize shock and vibration.

• Do not set the unit directly on the ground because it will

cause trouble.

Switch cover removal

(1) Remove the screw.

(2) Push downward the cover.

Installing the switch cover

After inserting the hook of Switch cover, then push upward,

and then tighten the tapping screw.

WARNING

• Install the unit where it will not be tilted by more than 5°.

• When installing the outdoor unit where it may exposed to strong wind, fasten it

securely.

Air purge

Always use a vacuum pump to purge the air.

Refrigerant for purging the air is not charged in the outdoor unit at the factory.

Close the high pressure side valve of the gauge manifold fully and do not operate it during

the following work.

CAUTION

• Refrigerant must not be discharged into atmosphere.

• After connecting the piping, check the joints for gas leakage with gas leak detector.

(1) Check if the piping connections are secure.

(2) Check that the stems of 2-way valve and 3-way valve are closed fully.

(3) Connect the gauge manifold charge hose to the charging port of the 3-way valve

(side with the projection for pushing in the valve core).

(4) Open the low pressure side valve of the gauge manifold fully.

(5) Operate the vacuum pump and start pump down.

(6) Slowly loosen the ﬂ are nut of the 3-way valve and check if air enters, then retighten

the ﬂ are nut.

(When the ﬂ are nut is loosened the operating sound of the vacuum pump changes

and the reading of the compound pressure gauge goes from minus to zero.)

(7) Pump down the system for at least 15 minutes, then check if the compound pressure

gauge reads -0.1 MPa (-76 cmHg, -1 bar).

(8) At the end of pump down, close the low pressure side gauge of the gauge manifold

fully and stop the vacuum pump.

(9) Slowly loosen the valve stem of the 3-way valve. When the compound pressure

gauge reading reaches 0.1-0.2 MPa, retighten the valve stem and disconnect the

charge hose from the 3-way valve charging port.

(If the stem of the 3-way valve is opened fully before the charge hose is

disconnected, it may be difﬁ cult to disconnect the charge hose.)

(10) Fully open the valve stems of the 2-way valve and 3-way valve using a hexagon

wrench. (After the valve stem begins to turn, turn it with a torque of less than

2.9 N • m until it stops turning.)

(11) Firmly tighten the 2-way valve and 3-way valve blank cap and the charging port cap.

Charging port

3-way valve

Charging

port cap

2-way valve

High pressure

side valve

(closed)

Compound pressure gauge

-0.1 MPa (-76 cmHg -1 bar)

Low pressure

side valve

Gauge manifold

Pressure gauge

Flare nut

Valve stem

Blank cap

Charge hose

Vacuum pump

Charge hose

Tightening torque [N • m(kgf • cm)]

Blank cap 20.0 to 25.0 (200 to 250 )

Charging port cap 12.5 to 16.0 (125 to 160 )

Additional charge

Refrigerant suitable for a piping length of 7.5 m is charged in the outdoor unit at the

factory.

When the piping is longer than 7.5 m, additional charging is necessary.

For the additional amount, see the table below.

Pipe length 7.5 m 15 m Rate

Additional refrigerant None +120 g 16 g/m

CAUTION

• When adding refrigerant, add the refrigerant from the charging port at the completion

of work.

• The maximum length of the piping is 15 m. If the units are further apart than this,

correct operation can not be guaranteed.

Between 7.5 m and 15 m, when using a connection pipe other than that in the table,

charge additional refrigerant with 16g/1 m as the criteria.

Outdoor unit wiring

2(N)

Cable clamp

Screw

Earth

(Ground)

screw

Earth

(Ground)

screw

Indoor unit terminal block

Connection cable

Outdoor unit terminal block

Power supply cable

Earth

(Ground)

screw

Earth

(Ground)

screw

Cable clamp

(1) Remove the outdoor unit switch cover.

(2) Remove the outdoor unit cable clamp and nylon

clamp.

(3) Securely crimp the ring terminals to the cables

using an appropriate tool so that the wires do not

come loose.

(4) Connect the ring terminals fully into the terminal

block.

(5) Fasten the sheath with a cable clamp.

(6) Install switch cover.

IM_01_9385991354-EN.indd 7IM_01_9385991354-EN.indd 7 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-8

CAUTION

Be careful not to generate a spark as follows for using a ﬂ ammable refrigerant.

• Do not remove the fuse while the power is on.

• Do not disconnect the wiring while the power is on.

• It is recommended to position the outlet connection in a high position. Place the cords

so that they do not get tangled.

• Match the terminal block numbers and connection cable colors with those of the

outdoor unit. Incorrect wiring may cause a ﬁ re.

• When ﬁ xing the connection cable with the cable clamp, always fasten the cable at the

plastic jacket portion, but not at the insulator portion. If the insulator is chafed, electric

leakage may occur.

• Always connect the earth (ground) wire. Improper earthing (grounding) work can

cause electric shocks.

• Connect the connection cables ﬁ rmly to the terminal block. Imperfect installation may

cause a ﬁ re.

• Do not use the ground screw for the indoor unit to the outdoor unit unless it is

speciﬁ ed.

7. FINISHING

CONNECTION PIPE, CABLE AND DRAIN HOSE

(Rear)

(A)Rear

outlet

(C)Bottom

outlet

(B)Right

outlet

(1) Insulate between pipes.

[(A)Rear, (B)Right, and (C)Bottom piping]

• Overlap the connection pipe heat insulation and indoor unit pipe heat insulation and

bind them with vinyl tape so that there is no gap.

Connection pipe

heat insulation

Indoor unit pipe

heat insulation

Bind the pipes together

so that there is no gap.

[Example of the right piping]

Indoor unit (Rear)

Vinyl tape

Overlap

Check that:

• When connected from the left rear, the drain hose is at the bottom left of the wall pipe.

(For connection from the left rear)

Drain hose

Wall pipe

(View from indoors)

Connection pipe

Connection cable

Saddle*

Outside

wall cap*

Sealer

putty*

(Outdoors)

Wall

*Locally purchased

Pipe

Check the following:

Prohibited Prohibited Prohibited

Good

Drain hose

Saddle

Lifted up

Wave

End in water

8. TEST RUN

• Perform test operation and check items 1 and 2 below.

• For the test operation method, refer to the operating manual.

• The outdoor unit, may not operate, depending on the room

temperature. In this case, press the TEST RUN button on the

remote controller while the air conditioner is running. (Point

the transmitter section of the remote controller toward the air

conditioner and press the TEST RUN button with the tip of a

ball-point pen, etc.)

• To end test operation, press the remote controller START/STOP button.

(When the air conditioner is run by pressing the TEST RUN button, the OPERATION

indicator lamp and TIMER indicator lamp will simultaneously ﬂ ash slowly.)

1. Indoor unit

(1) Is operation of each button on the remote control unit normal?

(2) Does each lamp light normally?

(3) Do the airﬂ ow direction louver operate normally?

(4) Is the drain normal?

2. Outdoor unit

(1) Is there any abnormal noise and vibration during operation?

(2) Will noise, wind, or drain water from the unit disturb the neighbors?

(3) Is there any gas leakage?

Transmitter

section

TEST RUN button

9. CUSTOMER GUIDANCE

Explain the following to the customer in accordance with the operating manual.

(1) Starting and stopping method, operation switching, temperature adjustment, timer,

airﬂ ow switching, and other remote controller operations.

(2) Air ﬁ lter removal and cleaning, and how to use the air louvers.

(3) Give the operating and installation manuals to the customer.

10. FRONT PANEL REMOVAL AND INSTALLATION

Intake grille removal

(1) Open the intake grille.

(2) Pull down the knob.

(3) Lift the intake grille upward and until

the bearing at the top of the intake

grille is removed.

Intake grille

Knob

Intake grille installation

(1) The ﬁ xing axle of the intake grille is

installed on the front panel.

(2) Lay down the intake grille.

Intake grille

Mounting shaft

Bearing

Front panel

Front panel removal

(1) Remove intake grille (Refer to the item of intake grille removal.)

(2) Remove six screws.

(3) The thumb is hung on the lower part as shown in the ﬁ gure, and it pulls to the front,

pushing [p] mark, and bottom hooks (two position)is removed from wall hook bracket.

Screws

(6 position)

Front panel

Wall hook bracket

Push

[p] mark

(4) The front panel is pulled to the front, raising the upper surface, and a front panel is

removed.

Front panel

IM_01_9385991354-EN.indd 8IM_01_9385991354-EN.indd 8 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-9

Front panel installation

(1) Firstly, ﬁ t the lower part of the front panel, and insert top and bottom hooks. (Top

center and both sides)

(2) Six screws is attached.

(3) The intake grille is attached.

Top hole (center)

Top hook (center)

Front panel

Indoor unit

Top holes

(two sides)

Top hooks (two sides)

CAUTION

Install the front panel and intake grille securely.

If installation is imperfect, the front panel or intake grille may fall off and cause injury.

11. OPTIONAL KIT INSTALLATION

This air conditioner can be connected with the following optional kits. Refer to each

installation manual for the method of installing parts.

• Wired remote controller

11.1. Before installing optional remote controller

• When you use optional remote controller, some functions may not be used.

• Please use the recommended optional remote controller.

CAUTION

Before installing, be sure to disconnect all power supply.

Don’t touch the heat exchanger.

During installing or removing operation, be sure not to have wire caught by parts or

draw it hard. Or it may result troubles to the air-conditioner.

Avoid place in direct sunlight.

Select place that will not be affected by the heat from a stove, etc.

Before setting up the optional kit, please conﬁ rm whether air-conditioner can receive the

signal.

Do not connect the optional remote controller to the terminal for power supply.

When connecting the optional remote controller with the indoor unit, please use the

connecting cable packaged up with the optional remote controller.

Recommended cable length of optional remote controller is 10 m. Make sure to do

insulate of connecting part when extended the cable.

]

11.2. Remote controller cable modiﬁ cation

(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then

remove the insulation from the cut end of the cable.

(2) Connect the remote controller cable and connecting cable. (supplied with wired remote

controller)

Important: Be sure to solder wires to connect. Be sure to insulate the connection

between the wires.

Connecting cable

White

Red

White

Red

Black

Insulated

connection

Remote

controller cable

Remote

controller cable

20 mm

11.3. Front panel, control box cover and display case

removal

(1) Refer to “10. FRONT PANEL REMOVAL AND INSTALLATION” to remove the front

panel.

(2) Remove the screw then remove the control cover.

(3) Remove the display case and connector.

Control cover

Screw

CN10

Connector

Screw

Display case

DISPLAY

11.4. Connecting cable to control board connector

(1) Pass the cable from the hole in the back of indoor unit.

(2) Connect the cable to the control board connector.

(3) Hook the cable to the rib.

hole

IM_01_9385991354-EN.indd 9IM_01_9385991354-EN.indd 9 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-10

CN9

Rib

Connect the cable

REMOCON

(4) Use cable clip and screw to fasten the cable of wired remote controller.

Screw

Cable clip

Conduit

holder

Screw

Cable clip

Wire of

wired

remote

controller

Original cable of

control unit

11.5. Front panel, control box cover and display case

installation

]

Install front panel, control box cover and display case by the reverse procedures as stated

in “11.3. Front panel, control box cover and display case removal”.

12. PUMP DOWN OPERATION

(FORCED COOLING

OPERATION)

To avoid discharging refrigerant into the atmosphere at the time of relocation or disposal,

recover refrigerant by doing the forced cooling operation according to the following

procedure.

(1) Conduct preliminary operation for 5 to 10 minutes using the forced cooling operation.

Start the forced cooling operation. Keep on pressing the MANUAL AUTO button of the

indoor unit for more than 10 seconds. The operation indicator lamp and timer indicator

lamp will begin to ﬂ ash simultaneously during test run. (The forced cooling operation

cannot start if the MANUAL AUTO button is not kept on pressing for more than 10

seconds.)

(2) Close the valve stem of 2-way valve completely.

(3) Continue the forced cooling operation for 2 to 3 minutes, then close all the valve

stems on the 3-way valves

(4) Stop the operation.

• Press the START/STOP button of the remote controller to stop the operation.

• Press the MANUAL AUTO button when stopping the operation from the indoor unit

side.

(It is not necessary to press down for more than 10 seconds.)

CAUTION

Please check the refrigerant circuit for any leaks before starting the pump down

operation.

Do not proceed with the pump down operation if there is no refrigerant left in the circuit

due to bent or broken piping.

During the pump down operation, be sure to turn off the compressor before removing

the refrigerant piping.

13. SELECTING THE REMOTE CONTROLLER

CUSTOM CODE

When two or more air conditioners are installed in a room and the remote controller is

operating an air conditioner other than the one you wish to set, change the custom code

of the remote controller to operate only the air conditioner you wish to set (four selections

possible).

When two or more air conditioners are installed in a room, please contact your retailer to

set the individual air conditioner custom codes.

• Conﬁ rm the setting of the remote controller custom code and the printed circuit board

setting.

If these are not conﬁ rmed, the remote controller cannot be used to operate for the air

conditioner.

Selecting the Remote Controller Custom Code

Use the following steps to select the custom code of the remote controller. (Note that the

air conditioner cannot receive a custom code if the air conditioner has not been set for the

custom code.)

(1) Press the START/STOP button until only the clock

is displayed on the remote controller display.

(2) Press the MODE button for at least 5 seconds to

display the current custom code (initially set to

(3) Press SET TEMP. (

) ( ) button to change the

custom code between

→ → → . Match

the code on the display to the air conditioner

custom code.

(4) Press the MODE button again to return to the clock

display. The custom code will be changed.

If no buttons are pressed within 30 seconds after the custom code is displayed, the

system returns to the original clock display. In this case, start again from step 1.

The air conditioner custom code is set to A prior to shipment.

Contact your retailer to change the custom code.

The remote controller resets to custom code A when the batteries in the remote

controller are replaced. If you use a custom code other than custom code A, reset the

custom code after replacing the batteries.

If you do not know the air conditioner custom code setting, try each of the custom codes

(

→ → → ) until you ﬁ nd the code which operates the air conditioner.

14. FUNCTION SETTING

Perform the Function Setting according to the installation conditions using the remote

controller.

CAUTION

• Conﬁ rm whether the wiring work for Outdoor unit has been ﬁ nished.

• Conﬁ rm that the cover for the electrical enclosure on the outdoor unit is in place.

• This procedure changes to the function settings used to control the indoor unit according

to the installation conditions. Incorrect settings can cause the indoor unit to malfunction.

• After the power is turned on, perform the Function Setting according to the installation

conditions using the remote controller.

• The settings may be selected between the following two: Function Number and Setting

Value.

• Settings will not be changed if invalid numbers or setting values are selected.

Entering the Function Setting Mode

While pressing the FAN button and SET TEMP. ( ) simultaneously, press the RESET

button to enter the function setting mode.

]

STEP 1

Setting the Remote controller Custom Code

Use the following steps to select the custom code of

the remote controller. (Note that the air conditioner

cannot receive a signal if the air conditioner has not

been set for the custom code.) The custom code

that is set through this process is applicable only to

the custom code in the FUNCTION SETTING. For

details on how to set the custom code through the

normal process, refer to SELECTING THE REMOTE

CONTROLLER CUSTOM CODE.

1 Press the SET TEMP. ( ) ( ) button to change the custom code between →

→

→ . Match the code on the display to the air conditioner custom code. (initially

set to

) (If the custom code does not need to be selected, press the MODE button

and proceed to STEP 2.)

2 Press the MODE button to accept the custom code, and proceed to STEP 2.

The air conditioner custom code is set to prior to shipment.

Contact your retailer to change the custom code.

The remote controller resets to custom code

when the batteries in the remote

controller are replaced. If you use a custom code other than custom code

, reset

the custom code after replacing the batteries.

If you do not know the air conditioner custom code setting, try each of the custom

codes (

→ → → ) until you ﬁ nd the code which operates the air conditioner.

IM_01_9385991354-EN.indd 10IM_01_9385991354-EN.indd 10 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-11

STEP 2

Selecting the Function Number and Setting Value

1 Press the SET TEMP. ( )

(

) buttons to select the function

number.

(Press the MODE button to switch

between the left and right digits.)

2 Press the FAN button to proceed to

setting the value.

(Press the FAN button again to return to

the function number selection.)

3 Press the SET TEMP. (

)

(

) buttons to select the setting value.

(Press the MODE button to switch between the left and right digits.)

Press the TIMER MODE button, then after you hear the beep emitted from the indoor

unit, press the START/STOP button to conﬁ rm the settings.

5 Press the RESET button to cancel the function setting mode.

6 After completing the FUNCTION SETTING, be sure to turn off the power and turn it

on again.

CAUTION

After turning off the power, wait 30 seconds or more before turning on it again.

The Function Setting does not become active unless the power is turned off then on

again.

Filter sign

Select appropriate intervals for displaying the ﬁ lter sign on the indoor unit according to the

estimated amount of dust in the air of the room.

If the indication is not required, select “No indication” (03).

(♦... Factory setting)

Setting Description

Function

Number

Setting Value

Standard (400 hours)

Long interval (1,000 hours) 01

Short interval (200 hours) 02

♦ No indication 03

Room temperature control for cooling

Depending on the installed environment, correction of the room temperature sensor may

be required. Select the appropriate control setting according to the installed environment.

(♦... Factory setting)

Setting Description

Function

Number

Setting Value

♦ Standard

Lower control 01

Auto restart

Enable or disable automatic restart after a power interruption.

(♦... Factory setting)

Setting Description

Function

Number

Setting Value

♦ Enable

Disable 01

* Auto restart is an emergency function such as for power outage etc. Do not attempt to

use this function in normal operation. Be sure to operate the unit by remote controller or

external device.

Function number

Setting

value

Room temperature sensor switching

(Only for wired remote controller)

When using the Wired remote controller temperature sensor, change the setting to “Both”

(01).

(♦... Factory setting)

Setting Description

Function

Number

Setting Value

♦ Indoor unit

Both 01

00: Sensor on the indoor unit is active.

01: Sensors on both indoor unit and wired remote controller are active.

* Remote controller sensor must be turned on by using the remote controller

Remote controller custom code

(Only for wireless remote controller)

The indoor unit custom code can be changed. Select the appropriate custom code.

(♦... Factory setting)

Setting Description

Function

Number

Setting Value

♦ A

B01

C02

D03

Setting record

Record any changes to the settings in the following table.

Setting Description Setting Value

Filter sign

Room temperature control for cooling

Auto restart

Room temperature sensor switching

Remote controller custom code

After completing the FUNCTION SET TING, be sure to turn off the power and turn it on

again.

IM_01_9385991354-EN.indd 11IM_01_9385991354-EN.indd 11 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

En-12

15. ERROR CODES

If you use a wireless remote controller, the lamp on the photo detector unit will output error

codes by way of blinking patterns. If you use a wired remote controller, error codes will

appear on the remote controller display. See the lamp blinking patterns and error codes in

the table. An error display is displayed only during operation.

Error display

Wired

remote

controller

Error code

Description

OPERATION

lamp

(green)

TIMER

lamp

(orange)

POWERFUL

lamp

(green)

●

(1)

●

(1)

◊

Serial communication error

●

(1)

●

(2)

◊

Wired remote controller

communication error

●

(1)

●

(5)

◊

Check run unfinished

●

(2)

●

(1)

◊

Unit number or Refrigerant circuit

address setting error

[Simultaneous Multi]

●

(2)

●

(2)

◊

Indoor unit capacity error

●

(2)

●

(3)

◊

Combination error

●

(2)

●

(4)

◊

• Connection unit number

error (indoor slave unit)

[Simultaneous Multi]

• Connection unit number error

(indoor unit or branch unit)

[Flexible Multi]

●

(2)

●

(7)

◊

Master unit, slave unit set-up error

[Simultaneous Multi]

●

(3)

●

(2)

◊

Indoor unit PCB model

information error

●

(3)

●

(5)

◊

Manual auto switch error

●

(4)

●

(1)

◊

Room temp. sensor error

●

(4)

●

(2)

◊

Indoor unit Heat Ex. Middle temp.

sensor error

●

(5)

●

(1)

◊

Indoor unit fan motor error

●

(5)

●

(3)

◊

Drain pump error

●

(5)

●

(7)

◊

Damper error

●

(5)

●

(15)

◊

Indoor unit error

●

(6)

●

(2)

◊

Outdoor unit main PCB model

information error or

communication error

●

(6)

●

(3)

◊

Inverter error

●

(6)

●

(4)

◊

Active filter error, PFC circuit

error

●

(6)

●

(5)

◊

Trip terminal L error

●

(6)

●

(8)

◊

Outdoor unit rush current limiting

resister temp. rise error.

●

(6)

●

(10)

◊

Display PCB microcomputers

communication error

●

(7)

●

(1)

◊

Discharge temp. sensor error

●

(7)

●

(2)

◊

Compressor temp. sensor error

●

(7)

●

(3)

◊

Outdoor unit Heat Ex. liquid temp.

sensor error

●

(7)

●

(4)

◊

Outdoor temp. sensor error

●

(7)

●

(5)

◊

Suction Gas temp. sensor error

●

(7)

●

(6)

◊

• 2-way valve temp. sensor error

• 3-way valve temp. sensor error

●

(7)

●

(7)

◊

Heat sink temp. sensor error

●

(8)

●

(2)

◊

• Sub-cool Heat Ex. gas inlet

temp. sensor error

• Sub-cool Heat Ex. gas outlet

temp. sensor error

●

(8)

●

(3)

◊

Liquid pipe temp. sensor error

●

(8)

●

(4)

◊

Current sensor error

●

(8)

●

(6)

◊

• Discharge pressure sensor error

• Suction pressure sensor error

• High pressure switch error

●

(9)

●

(4)

◊

Trip detection

●

(9)

●

(5)

◊

Compressor rotor position

detection error (permanent stop)

●

(9)

●

(7)

◊

Outdoor unit fan motor error

●

(9)

●

(9)

◊

4-way valve error

●

(10)

●

(1)

◊

Discharge temp. error

●

(10)

●

(3)

◊

Compressor temp. error

●

(10)

●

(4)

◊

High pressure error

●

(10)

●

(5)

◊

Low pressure error

●

(13)

●

(2)

◊

Branch boxes error

[Flexible Multi]

Display mode

●

: 0.5s ON / 0.5s OFF

◊

: 0.1s ON / 0.1s OFF

( ) : Number of flashing

[Troubleshooting with the indoor unit display]

OPERATION

OPERATION indicator lamp (green)

TIMER

TIMER indicator lamp (orange)

POWERFUL

POWERFUL indicator lamp (green)

[Troubleshooting with the Wired Remote Controller Display (Option)]

If an error occurs, the following display will be shown. (“Er” will appear in the set room

temperature display.)

Error code

IM_01_9385991354-EN.indd 12IM_01_9385991354-EN.indd 12 1/11/2560 BE 5:04 PM1/11/2560 BE 5:04 PM

Fujitsu ASMA13BETA Installation guide

Brand: Fujitsu

Model: ASMA13BETA

Category: Split-system air conditioners

Type: Installation guide

Download PDF

report

Fujitsu ASMA13BETA Installation guide

Fujitsu ASMA13BETA Installation guide

Related papers

Other documents