DFI DT122-HR User manual

Brand: DFI

Model: DT122-HR

Category: Chassis components

Type: User manual

This manual is also suitable for

DT122-HR Installation Guide

DFI DT122-HR is a compact and versatile system featuring 3rd/2nd Generation Intel® CoreTM processors (under 45W). It offers a wide range of connectivity options including 2 LAN ports, 2 COM ports, 1 DVI-I, 1 VGA, 4 USB 2.0 ports, Mic-in, Line-in, and Line-out. Its expansion capabilities include 1 PCI slot and 1 PCIe x16 slot, allowing for customization and expansion. Whether for industrial automation, digital signage, or other embedded applications, the DFI DT122-HR provides a reliable and flexible solution.

DT122-HR

Installation Guide

www.dﬁ .com

• 1 DT122-HR system unit

• 1 HDD drive bay kit

• 1 Quick Installation Guide

• 1 CD disk includes:

- Drivers/Manual

•

Power Cord

•

Wall Mount Kit

Package Contents

Optional Items

Front View

Power Button

HDD LED

Power LED

Reset Button

Rear View

Line-out

COM 2

Mic-in

Line-in

DVI-I

(DVI-D Signal)

COM 1

PS/2 KB

PS/2 Mouse

VGA

LAN 1-2

USB 2.0

Expansion slot

Key Features

DT122-HR

PROCESSOR

3rd/2nd Generation Intel

Core

processors (under 45W)

CHIPSET

Intel

QM67

LAN

2 LAN ports

COM

2 COM ports

DISPLAYS

1 DVI-I, 1 VGA

USB

4 Type A USB 2.0/1.1 ports

2 Type A USB 2.0/1.1 ports

AUDIO

Mic-in, Line-in, Line-out

Removing the Chassis Cover

1. Make sure the system and all other peripheral devices

connected to it has been powered-off.

2. Disconnect all power cords and cables.

3. The 4 mounting screws on the sides of the system are

used to secure the cover to the chassis. Remove these

screws and then put them in a safe place for later use.

Mounting

screw

Mounting

screw

4. After removing the mounting screws, slide the cover

backwards.

Slide the Cover Backward

5. The memory sockets and SATA drive bay are readily

accessible after removing the chassis cover.

Memory socket

2.5"/3.5" SATA

drive bay

1. Remove the 4 mounting screws that secure the drive

bay to the system.

Installing a 2.5" or 3.5" SATA

Drive

lnstalling a 2.5" SATA Drive

2. Turn to the other side of the drive bay and remove the

4 mounting screws that secure the HDD brackets to

the drive bay.

Mounting screw

Drive bay

3. Align the mounting holes of the SATA drive with the

mounting holes on the HDD bracket and then use the

provided mounting screws to secure the drive in place.

Mounting screw

SATA drive

HDD bracket

Mounting screw

4. Turn to the other side of the drive bay. Use the

provided mounting screws from step 2 to secure the

SATA drive (with HDD bracket) onto the drive bay.

Mounting screw

Drive bay

Mounting screw

5. Place the SATA drive bay assembly into the chassis.

Secure the SATA drive bay with the mounting screws

you removed in step 1.

Mounting screw

6. Connect the SATA data cable and SATA power cable to

the connectors on the SATA drive.

SATA data cable

SATA power

cable

2. Insert the spacer into the anti-shock bumper. You will

ﬁ nd the spacers in the HDD drive bay kit that comes

with the DT122 package.

lnstalling a 3.5" SATA Drive

Drive bay

spacer

3. Place the SATA drive on the drive bay. Align the

mounting holes of the SATA drive with the mounting

holes on the drive bay.

SATA drive

Drive bay

1. Remove the 4 mounting screws that secure the drive

bay to the system.

Mounting screw

Drive bay

4. Use the provided mounting screws to secure the SATA

drive onto the drive bay.

5. Place the drive bay into the chassis. Secure the drive

bay with the mounting screws you removed in step 1.

Mounting screw

Drive bay

Mounting screw

6. Connect the SATA data cable and SATA power cable to

the connectors on the SATA drive.

SATA data cable

SATA power cable

Important:

When inserting the riser

card, please select a

card within 175mm (as

shown on the next

picture).

Installing the PCI or PCIe x16

Expansion Card

The PCIe x16 slot on the motherboard is used to in-

sert a TS200-1P and TS200-1E riser card.

To install the expansion card, you need to remove the

mounting bracket and the mounting screw that secure

the bracket to the chassis and then remove the brack-

. Put the screw and the brackets in a safe place for

later use.

Mounting bracket

Mounting screw

Bracket

PCIe x16 slot

Mounting bracket and

mounting screw

PCI slot

T200-1P

T200-1E

2. Insert the Expansion card with a bracket into the PCI

or PCIe x16 slot that is on the riser card. Replace the

screw you removed in step 1 to secure the bracket in

place.

Mounting bracket

and mounting

screw

PCI

Bracket

Expansion card

Rear view

Note:

The Expansion card used in the above illustrations may not resemble the

actual cards. These illustrations are for reference only.

There are 2 types of wall mount brackets:

• Type A

• Type B

Mounting Options

Wall mount

Type A wall mount kit include:

• 2 type A wall mount brackets

1. If the mounting screw has been previously attached to

the top cover of the system, please remove them ﬁ rst.

Mounting screw

2. At the sides of the system, use the mounting screws

removed in step 1 to secure the wall mount brackets

on each side of the system.

Mounting screw

180.00

319.00

80.00

120.00

160.00 28.60

4-#6-32

16 2

Ø4.00

Ø8.50

Ø5.00

Ø3.60

300.00

78.00

4.00

74.00

Wall mount bracket

Type B wall mount kit include:

• 2 type B wall mount brackets

• Bracket screws

1. The 4 mounting holes on the sides of the system are

used to mount the type B wall mount bracket.

2. Use the provided mounting screws to secure the type

B wall mount brackets on each side of the system.

Wall mount bracket

5.00

R2.50

Ø8.50

4.00

300.00

335.00

360.00

40.00

55.00

40.00

55.00

78.00

5.00

934-DT1220-100G

A26601313

Board Layout and Jumper Settings

USB 0-1, 8-9 Power Select JP6

5V (default) 1-2 On

5V_standby 2-3 On

PS/2 Power Select JP2

5V (default) 1-2 On

5V_standby 2-3 On

COM 1 (JP4), COM 2 (JP5) RS232/RS422/RS485 Select

RS232 (default) 1-2 On

RS422 Full Duplex 3-4 On

RS485 5-6 On

COM 1 (JP1), COM 2 (JP3) RS232/Power

RS232 (default) 1-3, 2-4 On

RS232 with power 3-5 (+5V),

4-6 (+12V) On

Power-on Select JP7

Power-on via power button (default) 1-2 On

Power-on via AC power;

Power-on via WOL After G3

2-3 On

Clear CMOS Data JP10

Normal (default) 1-2 On

Clear CMOS Data 2-3 On

Panel Power Select JP9

+12V 1-2 On

+5V 3-4 On

+3.3V (default) 5-6 On

PS/2 Mouse

PS/2 KB

COM 2

COM 1

DVI-I port

(DVI-D signal only)

DVI-I

VGA

LAN 1 (Intel)

USB 1

USB 0

LAN 2 (Realtek)

USB 9

USB 8

Mic-in

Line-in

Line-out

PS/2 power

select (JP2)

COM1 RS232/Power

select (JP1)

JP1

JP3

COM2 RS232/Power

select (JP3)

JP4

JP5

COM1 RS232/422/485

select ( )JP4

COM2 RS232/422/485

select ( )JP5

ASMedia

1442

CPU fan

DDR3_1 SODIMM

DDR3_2 SODIMM

COM6

COM5

COM4

COM3

ATX Power

Power-on

select ( )JP7

Chassis

intrusion

DIO

Front

panel

Standby

Power LED

SPI Flash

BIOS

System fan

Battery

USB 0-1, 8-9 power

select (JP6)

Realtek

ALC262

Front audio

CD-in

S/PDIF

Intel

QM67

SATA 4

SATA 5

SATA 0

SATA 1

USB 2-3

USB 4-5

Clear CMOS

(JP10)

Panel power

select ( )JP9

LCD/Inverter

power

LVDS LCD

panel

40 39

PCIE x16

PCIE x1 PCIE x1

SATA 3.0

SATA 2.0

Socket G2

rPGA 988B

DFI DT122-HR User manual

Brand: DFI

Model: DT122-HR

Category: Chassis components

Type: User manual

This manual is also suitable for

DT122-HR Installation Guide

Download PDF

report

DFI DT122-HR User manual

This manual is also suitable for

DFI DT122-HR User manual

Related papers

Other documents