Hikoki SV 13YB User manual

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et

propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé

dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Model Random Orbit Sander

Modèle Ponceuse orbitale rotative

Modelo Lijadora excentrica

SV

13YA • SV

13YB

01Eng_SV13YA_US 9/7/07, 18:111

Page is loading ...

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

01Eng_SV13YA_US 8/22/12, 8:483

English

4

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the influence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different

from those intended could result in a

hazardous situation.

5) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts.

This will ensure that the safety of the power

tool is maintained.

01Eng_SV13YA_US 8/22/12, 8:484

English

5

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving parts.

4. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

5. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

6. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction

Manual.

7. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with

its operation or unauthorized personnel.

8. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

9. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

10. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

11. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times.

Check for dust build-up frequently.

12. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may burn

out.

01Eng_SV13YA_US 8/22/12, 8:485

English

6

13. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

14. NEVER leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

15. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

17. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

18. NEVER leave the random orbit sander on floor and so on while spinning.

19. NEVER apply water or lubricating oil, otherwise hazards from electrical shocks may

result.

20. NEVER push the random orbit sander too strongly onto a surface.

Pushing the random orbit sander too strongly may cause the sanding paper to tear or

shorten the life of the sander itself.

21. ALWAYS operate the random orbit sander safely for correct use.

This random orbit sander is a portable dry plane surface sander that was designed for

finishing wood and metal surfaces and ground coats.

22. ALWAYS securely installing the sanding paper.

23. ALWAYS wear a protective mask when operating the random orbit sander in confined

spaces.

24. Definitions for symbols used on this tool

V ............ volts

Hz .......... hertz

A ............ amperes

no .......... no load speed

W ........... watt

........... Class II Construction

---/min ... revolutions per minute

01Eng_SV13YA_US 8/22/12, 8:486

English

7

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation “ means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Therefore, either the symbol “

” or the

words “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in

wet environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_SV13YA_US 8/22/12, 8:487

English

8

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool.

NAME OF PARTS

Fig. 1

SPECIFICATIONS

Model SV13YA SV13YB

Motor Single Phase, Series Commutator Motor

Power source Single Phase 120V AC 60 Hz

Current 2.4 A 2.0 A

No-load speed 7,000 – 12,000/min 12,000/min

Sanding pad size

5” (125 mm)

(Outer diameter)

Sanding paper size

5” (125 mm)

(Outer diameter)

Weight 3.1 lbs. (1.4 kg)

Fig. 2 (SV13YA Only)

Housing (A)

Housing (B)

Lower

cover (B)

Dust bug

Lower cover (A)

Nameplate

Switch

Pad

Dial

01Eng_SV13YA_US 8/22/12, 8:488

English

9

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Roughing or finishing of woodwork and metal surfaces.

䡬 Preliminary sanding of woodwork and metal surfaces before painting.

䡬 Paint removal.

䡬 Rust removal.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle

while the switch is in the ON position, the power tool will start operating immediately

and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as short as

practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a faulty receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Check your working environment

Ensure the following before operation;

䡬 No flammable gas, liquid, or object at worksite.

䡬 Sanding thin steel sheet may cause a high booming sound.

In this case, place a rubber mat under the workpiece.

䡬 Take appropriate noise preventive measures to prevent adverse affects on the

environment by electrical noise.

䡬 Clear the area of children or unauthorized personnel.

01Eng_SV13YA_US 8/22/12, 8:489

English

10

6. Installing the sanding paper

Since the attachment is a hook-and-loop

type, the sanding paper can be installed

easily by just pressing it onto the pad. When

installing the sanding paper, in order to

match it to the holes in the pad, gently fold

it along the axis of two holes as shown in

Fig. 3.

Next, use the holes along the fold as a guide

to match the sanding paper and the pad.

Finally, press the entire sanding paper

uniformly onto the pad.

7. Attaching and removing the dust bag

(1) Attaching the dust bag

As shown in Fig. 4, hold the dust gate and

push it in the direction of arrow A to attach

it to the dust outlet.

(2) Removing the dust bag

As shown in Fig. 4, hold the dust gate and

pull it in the direction of arrow B to remove

it from the dust outlet.

8. Adjustment of speed (SV13YA only)

The SV13YA is equipped with the electric

control circuit which enables non-step speed

control. To adjust the speed, turn the dial

shown in Fig. 5. When the dial is set to “1”,

the sander operates at the minimum speed

(7,000/min). When the dial set to “6”, the

sander operates at the maximum speed

(12,000/min). Adjust the speed according to

the material to be cut and working efficiency.

Fig. 5

Fig. 3

Sanding paper

Pad

Fig. 4

Dust gate

Dust outlet

Dust bag

B

A

Dial

01Eng_SV13YA_US 8/22/12, 8:4810

English

11

Material

Grain

Dial scale

Rough grinding Fine grinding

Paintwork:

Sanding 180 400 3 – 6

Repairs

(scratches, rust spots) 120 240 2 – 4

Stripping 40 80 2 – 4

Wood:

Softwood 60 – 80 240 3 – 6

Hardwood 60 180 3 – 5

Veneers 240 320 2 – 4

Metals:

Aluminium 80 240 2 – 4

Steel 60 240 3 – 6

Stainless steel 120 240 3 – 6

By adjusting the dial, match the speed to the material and type of work.

NOTE: Please use this table as a standard.

RANDOM ORBIT SANDER OPERATION

WARNING: Never apply water or grinding fluid when sanding. This could result in

electrical shock.

1. How to hold the random orbit sander

While gripping the housing, lightly press the

sander against the surface to be sanded so

that the sanding paper uniformly contacts

the surface, as shown in Fig. 6. DO NOT

apply excessive pressure to the sander while

sanding. Excessive pressure may cause

overload of the motor, reduced service life

of the sanding paper, and lowered sanding

or polishing efficiency.

2. How to move the random orbit sander

Move the sander by either moving it up and

down or by moving it in circles while

gradually progressing in a sideways

direction. (Figs. 7 and 8)

Fig. 6

Fig. 7

01Eng_SV13YA_US 8/22/12, 8:4811

English

12

3. Switching the sander ON and OFF

The power can be turned on by setting the

lever to ON (1) and turned off by setting the

lever to OFF (0).

NOTE:

Never turn the power switch ON when the sander is contacting the surface to be sanded.

This is necessary to preclude damage to the material. The same applies when switching

the power OFF.

CAUTION:

䢇 lmmediately after use, always turn the sander off and unplug it.

䢇 Since the sander may suck in dust and debris, be careful not to place it where there is

much dust and debris when it is still spinning right after use.

HOW TO INSTALL THE OPTIONAL ACCESSORIES

WARNING: Be sure to switch power OFF and disconnect the plug to avoid

accidents.

䡬 Mounting the polyester buff

Since the attachment is a hook-and-loop

type as with the sanding paper, the

polyester buff can be mounted by just

pressing it onto the pad (Fig. 9).

Fig. 8

Fig. 9

Polyester buff

01Eng_SV13YA_US 8/22/12, 8:4812

English

13

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Emptying and cleaning the dust bag

If the dust bag contains too much saw dust, dust collection will be affected. Empty the

dust bag when it gets full.

Remove the dust bag, open the fastener, and dispose of the contents.

2. Inspecting the sanding paper

Since use of worn-out sanding paper will degrade efficiency and cause possible damage

to the pad, replace the sanding paper as soon as excessive abrasion is noted.

3. Inspecting the screws

Regularly inspect all screws and ensure that they are fully tightened. Should any of the

screws be loosened, retighten them immediately.

WARNING: Using this random orbit sander with loosened screws is extremely

dangerous.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection, carbon brush inspection and

replacement on this tool should ONLY be performed by a HITACHI AUTHORIZED

SERVICE CENTER.

5. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

6. Service parts list

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried

out by a HITACHI AUTHORIZED SERVICE CENTER.

This Parts List will be helpful if presented with the tool to the HITACHI AUTHORIZED

SERVICE CENTER when requesting repair or other maintenance. In the operation and

maintenance of power tools, the safety regulations and standards prescribed in each

country must be observed.

01Eng_SV13YA_US 8/22/12, 8:4813

English

14

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are

not intended for use with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement part or accessory

with your tool. The use of any other attachment or accessory can be

dangerous and could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Sanding paper (Velcro type) (Grain: #120) (Code No. 308519) ....................................... 1

(2) Dust bag (Code No. 323004) .............................................................................................. 1

OPTIONAL ACCESSORIES …………… sold separately

䡬 Sanding paper

䡬 Polyester buff (Code No. 308515)

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

Size (Outer diameter) Type Grit No. Code No.

AA40 308516

AA60 308517

AA80 308518

5” (125 mm) Velcro type

AA120 308519

AA180 308520

AA240 308521

AA320 308522

AA400 308523

01Eng_SV13YA_US 8/22/12, 8:4814

Page is loading ...

39

English

A: ltem No.

B: Code No.

C: No. Used

D: Remarks

Français

A: No. élément

B: No. code

C: No. utilisé

D: Remarques

Español

A: N°. item

B: N°. codigo

C: N°. usado

D: Observaciones

SV13YA

ABC D

1 324-249 1

2 301-653 7 D4 × 20

3 993-195 1

4 324-207 1

5

–––––––

1

6 937-631 1

7 984-750 2 D4 × 16

8 324-246 1 120V

9 959-140 1

10 938-307 1

11 311-948 1

12

–––––––

1

13 324-206 1

14

–––––––

1

15 953-327 1 D8.8

16 322-764 1

17 322-761 1

18 626-VVM 1 626VVC2PS2L

19 322-763 1

20 322-762 1

21 930-483 2

22 999-041 2

23 340-616D 1 120V

24 360-696U 1 120V “17, 24”

25 629-VVM 1 629VVC2PS2L

26 324-521 1

27 324-208 1

28 324-212 1

29 600-2DW 1 6002DDWCMPS2L

30 309-422 1

31 993-244 1 M4 × 12

32 324-210 1

33 324-211 1

34 324-209 1

35 307-109 3 M4 × 16

501 323-004 1

502 308-519 1 A-P120

503 324-613 1

03Spa_SV13YA_US 8/22/12, 8:4939

40

English

A: ltem No.

B: Code No.

C: No. Used

D: Remarks

Français

A: No. élément

B: No. code

C: No. utilisé

D: Remarques

Español

A: N°. item

B: N°. codigo

C: N°. usado

D: Observaciones

SV13YB

ABC D

1 324-214 1

2 301-653 7 D4 × 20

3 993-195 1

4 324-207 1

5

–––––––

1

6 984-750 2 D4 × 16

7 937-631 1

9 938-307 1

10 311-948 1

11

–––––––

1

12 324-206 1

13

–––––––

1

14 953-327 1 D8.8

15 322-764 1

16 322-761 1

17 626-VVM 1 626VVC2PS2L

18 322-763 1

19 322-762 1

20 930-483 2

21 999-041 2

22 340-618D 1 120V

23 360-698U 1 120V “17, 24”

24 629-VVM 1 629VVC2PS2L

25 324-521 1

26 324-208 1

27 324-212 1

28 600-2DW 1 6002DDWCMPS2L

29 309-422 1

30 993-244 1 M4 × 12

31 324-210 1

32 324-211 1

33 324-209 1

34 307-109 3 M4 × 16

501 323-004 1

502 308-519 1 A-P120

03Spa_SV13YA_US 8/22/12, 8:4940

Page is loading ...

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construc-

tion activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

AVERTISSEMENT:

La poussière résultant d'un ponçage, d'un sciage, d'un meulage, d'un perçage ou de toute

autre activité de construction renferme des produits chimiques qui sont connus par l'Etat

de Californie pour causer des cancers, des défauts de naissance et autres anomalies de

reproduction. Nous énumérons ci-dessus certains de ces produits chimiques:

● Plomb des peintres à base de plomb,

● Silice cristalline des briques et du ciment et autres matériaux de maçonnerie, et

● Arsenic et chrome du bois d'oeuvre traité chimiquement.

Le risque d'exposition à ces substances varie en fonction de la fréquence d'exécution

de ce genre de travail. Pour réduire l'exposition à ces produits chimiques, travailler

dans un lieu bien ventilé, et porter un équipement de protection agréé, par exemple

un masque anti-poussière spécialement conçu pour filter les particules microscopiques.

ADVERTENCIA:

Algunos polvos creados por el lijado mecánico, el aserrado, el esmerilado, el taladrado

y otras actividades de construcción contienen sustancias químicas conocidas por le

Estado de California como agentes cancerígenos, defectos congénitos y otros daños

reproductores. Algunos ejemplos de estas sustancias químicas son:

● El plomo de las pinturas a base de plomo,

● El sílice cristalino de los ladrillos y cemento y otros productos de mampostería, y

● El arsénico y el cromo de la madera tratada químicamente.

El riesgo resultante de la exposición varía según la frecuencia con que se realiza este

tipo de trabajo. Para reducir la exposicíon a esta sustancias químicas: trabaje en un lugar

bien ventilado y realice el trabajo utilizando el equipamiento apropiado, tal como las

máscaras para el polvo especialmente diseñados para eliminar las partículas minúsculas.

400

Code No. C99138964 G

Printed in China

Issued by

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

Hitachi Koki U.S.A., Ltd.

PO Box 970

Braselton, GA 30517

Hitachi Koki Canada Corp.

450 Export Blvd. Unit B,

Mississauga ON L5S 2A4

Avenida Isaac Newton No.286, Piso 2, Colonia Polanco Sección V,

Delegación Miguel Hidalgo, C. P. 11560

México, D. F.

03Spa_SV13YA_US 9/23/14, 11:29 AM44

Hikoki SV 13YB User manual

This manual is also suitable for

Hikoki SV 13YB User manual

in other languages

Related papers

Other documents