IKEA HOO D00S Program Chart

5019 618 33048/A

УСТАНОВКА И ЭКСПЛУАТАЦИЯ ВЫТЯЖКИ

Примечание к установке: Вытяжка должна быть установлена на расстоянии не менее

50 см от электрических конфорок и не менее 65 см от газовых, керосиновых или угольных

конфорок. Если интрукциями по установке газового прибора предусмотрено большее

расстояние, то данное указание должно быть соблюдено.

Примечание к установке и эксплуатации: Прежде чем установить или использовать

вытяжку внимательно прочитайте настоящее руководство. Чертежи приведены на первых

страницах. Фирма&изготовитель снимает с себя всякую ответственность за возникновение

каких&либо проблем, вреда или пожара, возникающих в результате несоблюдения

приведенных в настоящем руководстве инструкций.

Монтаж вытяжки рекомендуется доверятья квалифицированному специалисту.

ИНСТАЛИРАНЕ И УПОТРЕБА

Бележка за инсталирането: Аспираторът трябва да се инсталира на разстояние 50 см от

електрически печки и 65 см от печки на газ, нафта или смесени. Ако в инструкциите на

устройството за готвене на газ е указано по&голямо разстояние за тази спецификация,

трябва да се изпълнява това разстояние.

Бележка за инсталиране и употреба: Преди инсталиране или употреба на аспиратора

прочетете внимателно това ръководство & чертежите се намират на първите страници.

Производителят не носи отговорност за каквито и да било неудобства, повреди или

запалвания, предизвикани от неспазване на инструкциите, посочени в това ръководство.

Препоръчва се за инсталирането на аспиратора да се посъветвате с квалифициран техник.

INSTALAREA ȘI UTILIZAREA

Notă privind instalarea: Hota trebuie să fie instalată la o distanţă minimă de 50 cm faţă de arzătoarele

electrice și de 65 cm faţă de arzătoarele pe bază de gaze sau mixte. Dacă instrucţiunile de instalare

ale mașinii de gătit cu gaz specifică o distanţă mai mare decât cea indicată, trebuie să ţineţi cont de ea.

Notă privind instalarea și utilizarea: Înainte de a instala sau de a utiliza hota, citiţi cu atenţie acest

manual, desenele se găsesc pe primele pagini. Producătorul nu-și asumă nici o răspundere pentru

eventualele inconveniente, pagube sau incendii provocate aparatului, rezultate din nerespectarea

instrucţiunilor din acest manual.

Se recomandă să consultaţi un tehnician calificat pentru instalare.

INSTALLATION AND USE

For installation: The hood must be installed at least 50 cm from electric cookers and 65 cm from gas, gas oil or

coal cookers. If the installation instructions for a gas cooker specify a greater distance, then this distance must be

observed.

For installation and use: Before installing or using the hood, read this manual carefully. The drawings are at the

front of the manual. The Manufacturer declines all liabillity for any faults, damage or fires caused by the appliance

as a result of failure to observe the instructions and recommendations given in this manual.

Contact a qualified technician for installation.

RUS

61833048a.fm Page 2 Tuesday, February 21, 2006 7:28 PM

5019 618 33048/A

61833048a.fm Page 3 Tuesday, February 21, 2006 7:28 PM

5019 618 33048/A

61833048a.fm Page 4 Tuesday, February 21, 2006 7:28 PM

5019 618 33048/A

INSTALLATION AS AN EXTRACTOR OR FILTER HOOD

Important: the figures are on the first pages of this booklet.

• Fix the bracket on the rear of the hood near the coupling ring (Fig. 1.1a).

Note: the bracket can be adjusted horizontally, which enables the position of the hood to be adjusted (Fig. 1.1b).

• Trace a centre line on the wall between the hob and ceiling (Fig. 2.2).

Mark the distance from the hob (respecting the minimum distance) with the pencil and position the template (if provided)

against the wall on the mark (Fig. 2.3).

Then mark and drill the hole, insert the wall plug and partially tighten 1 screw (Fig. 2.4).

• Fix the flue support as close as possible to the ceiling (Fig. 3.1). For filter operation, in this phase, also fix the deflector (Fig.

3.2).

Hang the hood on the partially tightened screw (Fig. 3.3a - if necessary, adjust the hood horizontally by means of the

bracket - Fig- 3.3b)

Mark the hood fixing points:

2 at the bottom: remove the grease filters (Fig. 3.4), 2 at the top on the sides of the bracket.

Remove the hood, drill the holes, insert the plugs into the holes (Fig. 3.5), refit the hood, insert and tighten all the screws

(Fig.3.6 - Fig. 3.7)

External Exhaust Mode: Fumes are extracted and expelled to the outside through a fume hose fixed to the collar at the top

of the hood.

Caution! If the hood is equipped with a carbon filter, this must be removed.

Exhaust air must not be conveyed through a flue used for removal of fumes produced by gas combustion appliances or other

combustible materials, but must have an independent outlet. All national regulations governing extraction of fumes must be

observed.

Filter Hood: Air is filtered through a carbon filter and returned to the room.

Caution! If the hood is not already equipped with a carbon filter, one must be ordered and fitted prior to use.

Installing the telescopic flue

• Connect the hood to the mains supply and fix the telescopic flue to the flue bracket with two screws. Slide the bottom

section down into its seat on the top of the hood (Fig. 4).

ROSK H RUS BGCZPL GB

61833048a.fm Page 26 Tuesday, February 21, 2006 7:28 PM

5019 618 33048/A

1. Control panel.

Light :

move the switch to the right or press the button to switch

on.

Extraction speed :

move the switch to the right or press the next button to

increase extraction speed (or open the shutter ).

2. Grease filters.

3. Lamp covers(or halogen lamps, depending on the

model).

4. Telescopic flue.

Grease filters:

Metal grease filters have an unlimited

life and should be washed once a

month either by hand or in a

dishwasher at a low temperature and

in a short cycle. Washing in a

dishwasher can cause grease filters to

turn white, but this in no way affects

efficiency.

Press the handle to release the filter

Wash the filter and leave it to dry. Refit the filter in reverse

order.

Bulb/s:

Detach the lighting unit and remove

the burnt-out bulb.

Refit the filters.

Halogen bulbs:

Use a small screwdriver or any other

suitable tool to prise off the bulb cover.

Replace the bulb cover so that it clicks

into position.

Use only max 40 W

- E14 bulbs or max 20 W halogen

bulbs (depending on the model),

taking care not to touch them with

your hands.

Fitting or replacing the carbon filter

(filter hoods only).

Change the carbon filter every six months.

1. Remove the grease filters.

2. Fit the filters as shown in the figures below.

3. Reverse the above procedure to remove the carbon

filter.

4. Refit the grease filters.

CLEANING THE HOOD

Warning! Failure to remove oil and grease at least once a

month could lead to fire.

Use a soft cloth damped in a neutral detergent. Never use

abrasives or alcohol.

BEFORE USING THE HOOD

Please read these instructions carefully in order to get the

best out of your new hood.

Packaging materials can be dangerous for children. Keep

packaging materials (plastic bags, polystyrene, etc.) well out

of their reach.

Make sure the hood has not been damaged during transport.

Installation and electrical connections must be carried out by

a qualified technician in compliance with local safety

regulations.

CLACK!

61833048a.fm Page 27 Tuesday, February 21, 2006 7:28 PM

5019 618 33048/A

PROTECTING THE ENVIRONMENT

1. Packaging

Packaging materials are 100% recyclable and are marked

with the recycling symbol . Dispose of packaging materials

in compliance with local waste disposal regulations. Packaging

materials can be dangerous for children. Keep packaging

materials (plastic bags, polystyrene, etc.) well out of their

reach.

2. Appliance

This appliance is marked according to the European directive

2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment

and human health, which could otherwise be caused by

inappropriate waste handling of this product.

The symbol on the product, or on the documents

accompanying the product, indicates that this appliance may

not be treated as household waste. Instead it shall be handed

over to the applicable collection point for the recycling of

electrical and electronic equipment.

Disposal must be carried out in accordance with local

environmental regulations for waste disposal.

For more detailed information about treatment, recovery and

recycling of this product, please contact your local city office,

your household waste disposal service or the shop where you

purchased the product.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

WARNING!

• Do not allow children or infirm persons to operate

the appliance without supervision.

• Make sure that children do not play with the

appliance.

1. Do not connect the appliance to the mains electricity

supply until installation is completed. Always disconnect

the hood from the mains before performing any cleaning

or maintenance.

2. Do not “flambé” food under the hood. Naked flames

could cause fire.

3. Do not leave pans unattended when frying. Cooking oil

can catch fire.

4. Regular cleaning and maintenance is essential to correct

functioning and good performance. Regularly remove dirt

deposits. Regularly clean or replace filters. Never use

flammable materials as hoses for extracted air.

5. If the hood is used together with non-electrically powered

appliances, ambient negative pressure must not exceed

4Pa (4 x 10

-5

bars). Make sure that the room is

adequately ventilated.

Electrical connections

Before connecting the hood to the mains, make sure that the

voltage specified on the data plate corresponds to the voltage

in your home. The data plate is located inside the hood

behind the grease filter.

If the appliance is fitted with a power supply cable and plug,

the plug must be inserted in an accessible socket.

If the hood does not come pre-fitted with a mains plug, fit

one that conforms to applicable standards or use a double-

pole switch with a minimum breaking gap of 3 mm.

Replacement of the power supply cable with power plug or

flexible cable may only be carried out by an authorized

Service Centre or a qualified electrician.

Declaration of conformity

This product has been designed, manufactured and sold in

conformity to the following standards:

- safety objectives of the “Low Voltage” Directive

73/23/EEC

- protection requirements of “EMC” Directive 89/336/

EEC amended by Directive 93/68/EEC.

Trouble-shooting guide

Hood does not work:

• Is the power plug properly inserted in the mains socket?

• Is there a power failure?

• Is the mains fuse OK?

The hood is not extracting efficiently:

• Is the right extraction speed selected?

• Do the filters need to be cleaned or replaced?

• Are the air outlets blocked?

Light does not work:

• Does the bulb need to be replaced?

• Is the bulb correctly fitted?

• Is the mains fuse OK?

AFTER-SALES SERVICE

Before calling Technical Assistance

1. Check to see if you can fix the problem yourself

(see “Trouble-shooting guide”).

2. Switch the hood off for a few minutes then switch it back

on and see if the problem has gone.

3. If the problem persists, call Technical Assistance.

Specify:

• the nature of the problem,

• the model of hood, stated on the data plate inside the

hood, accessible by removing the grease filters.

• your full address,

• your telephone number and area code.

• the service code (the number appearing below the word

SERVICE on the data plate inside the hood behind the

grease filter).

If any repairs are needed, contact an authorised Service

Centre (to ensure that only original spare parts are used and

that repairs are made correctly).

Failure to comply with these instructions may compromise

the safety and quality of the product.

ROSK H RUS BGCZPL GB

61833048a.fm Page 28 Tuesday, February 21, 2006 7:28 PM

IKEA HOO D00S Program Chart

Related papers

Other documents