IKEA HOO E00 S is a versatile kitchen appliance that combines efficient odor and grease removal with elegant design. With its powerful extraction capabilities, it effectively eliminates fumes, smoke, and cooking odors, leaving your kitchen fresh and clean. The hood features adjustable extraction speeds, allowing you to customize its performance based on your cooking needs.
IKEA HOO E00 S is a versatile kitchen appliance that combines efficient odor and grease removal with elegant design. With its powerful extraction capabilities, it effectively eliminates fumes, smoke, and cooking odors, leaving your kitchen fresh and clean. The hood features adjustable extraction speeds, allowing you to customize its performance based on your cooking needs.
5019 618 33043
D F NL E
GB
P I GR
N
S
FINDK
EXTRACTOR OR FILTERING HOOD INSTALLATION
The minimum distance between the support surface of the recipients on the cooking device and the lowest part of the hood
must not be less than 50 cm in case of electric cookers and 65 cm for gas or combination cookers. If the installation instructions
for the gas cooker specify a greater distance, this must be taken into account. The fume hose and hose clamps are not supplied.
Contact a qualified technician for installation.
1. Mark a centre-line on the wall from the cooktop to the ceiling (1).
2. Taking into account the above-mentioned distances from the cooktop, mark the distance from the cooktop with a pencil and place the
template against the wall on the mark (2).
3. Using the template supplied, mark the holes, drill them and insert the rawlplugs(3), then partly screw in 2 screws in the top holes (4) and
hook the hood.
4. remove the grease filter/s (5).
5. Mark the holes for secure fixing (6).
6. Remove the hood from the bracket, drill and insert the wall plugs (7).
7. Hook the hood, tighten the two top screws (8) and insert the two safety screws in the bottom holes (9).
8. Fix the flue support to the wall as close as possible to the ceiling: drill and insert 2 plugs per wall (10), position the support (11) and fix it
with the 2 screws (12).
Extractor Version: steam and fumes are exhausted to the outside. Proceed as follows:
fit the collar with non-return valve supplied with the product (X) onto the exhaust opening of the hood, exerting light pressure. Screws are not
required to attach the collar. Then fit the adaptor for the exhaust pipe (Y) onto the collar, exerting light pressure. Fit an exhaust pipe which is
long enough to vent externally (13A). Care must be taken to ensure that the tube and adaptor fastening does not impede the electric shutter
from opening and closing . Important: If the hood is equipped with a carbon filter, this must be removed. The discharge air must not be ducted
to a flue used for removing fumes produced by appliances using gas or other fuels, but must have a separate outlet. All national regulations on
air discharge must be observed.
Filtering Version: The air is filtered by a carbon filter and recycled in the surrounding environment. In this case, fit the special deflector (13F)
to the lower flue, fixing it with 4 screws. Important: if the hood does not have a carbon filter, order one and fit it before use.
Connect the hood to the mains supply (14) and fix the telescopic flue to the flue bracket with two screws (15A). Slide the bottom section
down into its seat on the top of the hood and fix with two screws (15B).
Preparing the flange: remove the protective film (A) from the flange and apply it to the lower edge of the frame as shown in B.
Fitting the flange: fit the three brackets (16), partially undo the 6 screws (2 per bracket), bend and position the flange between the hood and
the brackets (17) so that the side with the protective strip is facing the edge of the hood. Fix the flange as close as possible to the brackets on
the edge of the hood.
GB
The hood's top surface can support a maximum
weight of 10 Kg.
61833043.fm Page 4 Thursday, April 6, 2006 9:14 AM
5019 618 33043
D F NL E
GB
P I GR
N
S
FINDK
1. Control panel
2. Grease filters
3. Grease filter handles
4. Light above cooker (depending on model)
5. Telescopic flue
To clean the grease filter
Clean the grease filter once a month.
1. Disconnect the electrical power supply.
2. Remove the grease filters - Fig. 1:
a - push the handles backwards
b - and then downwards.
3. After cleaning the grease filter refit in reverse order,
making sure the entire extraction surface is covered.
Fitting or replacing the carbon filter:
Change the carbon filter every six months.
1. Disconnect the electrical power supply.
2. Remove the grease filters (Fig. 1 - a, b).
3. Fit the filters over the motor: make sure the pins R on the
manifold match the slots S, then turn clockwise until
locked.
4. Carry out in the reverse order to remove.
5. Refit the grease filters.
Replacing bulbs
1. Disconnect the electrical power supply.
2. Remove the grease filters (Fig. 1 - a, b).
3. Remove the burnt-out bulb.
Replace using 40W max E14 bulbs only.
4. Refit the grease filters.
Halogen lamps:
Use a small screwdriver or other
suitable tool to prise off the cover. Refit
the cover.
5. Use only max 40 W - E14 bulbs
or max 20 W halogen bulbs
(depending on the model),
taking care not to touch them
with your hands.
CONTROL PANEL
Light switch.
The switch has two positions (lights OFF - lights ON).
To switch on the lights: move the switch to the right.
Extraction speed selection switch.
The extraction speed switch has different settings,
depending on the amount of steam and fumes.
To increase the extraction speed: move the switch to the
right.
Cleaning the hood
Warning! Failure to remove oil/grease (at least once a
month) could lead to fire.
Use a soft cloth with a neutral detergent. Never use abrasive
substances or alcohol.
Before using the hood
Please read these instructions carefully and keep them for
future reference, in order to ensure best use of your hood.
Packaging materials (plastic bags, polystyrene, etc.) can be
dangerous for children and should be kept well out of their
reach.
Make sure the hood has not been damaged during transport.
Installation and electrical connections must be carried out by
a qualified technician in compliance with the current local
regulations.
Fig.1
Fig.2
61833043.fm Page 5 Thursday, April 6, 2006 9:14 AM
5019 618 33043
D F NL E
GB
P I GR
N
S
FINDK
SAFEGUARDING THE ENVIRONMENT
1. Packaging
Packing materials are 100% recyclable and are marked with the
recycling symbol . Comply with local regulations for their
disposal. Packaging materials (plastic bags, polystyrene, etc.) can be
dangerous for children and should be kept well out of their reach.
2. Product
This appliance is marked in compliance with European Directive
2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is scrapped suitably, you can help
prevent potentially damaging consequences for the environment and
health.
The symbol on the appliance or accompanying documentation
indicates that this product should not be disposed of as unsorted
municipal waste but must be taken to a collection point for the
treatment of WEEE.
Disposal must be carried out in accordance with local environmental
regulations for waste disposal.
For further information on the treatment, recovery and recycling of
this appliance, contact your competent local authority, the collection
service for household waste or the shop where you purchased the
appliance.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
WARNING!
• Do not allow children or infirm persons to operate the
appliance without supervision.
• Make sure children do not play with the appliance.
1. Do not connect the appliance to the mains electricity supply until
installation is completed. Always disconnect the hood from the
mains before performing any cleaning or maintenance.
2. Do not “flambé” food under the hood. Naked flames could
cause a fire.
3. Do not leave pans unattended when frying. Cooking oil can
catch fire.
4. Regular cleaning and maintenance is essential to correct
functioning and good performance. Regularly remove dirt
deposits. Regularly clean or replace filters. Never use flammable
materials as hoses for extracted air.
5. If the hood is used together with non-electrically powered
appliances, ambient negative pressure must not exceed 4Pa
(4 x 10
-5
bars). Make sure the room is adequately ventilated.
Electrical connections
Before connecting the hood to the power supply, make sure the
voltage specified on the dataplate matches that in your home. The
dataplate is located inside the hood behind the grease filter.
If the appliance is fitted with a power cable and plug, the plug must
be placed in an accessible position.
If the hood does not come pre-fitted with a mains plug, fit one that
conforms to applicable standards or use a double-pole switch with a
minimum breaking gap of 3 mm.
Replacement of the power supply cable with power plug or flexible
cable may only be carried out by an authorized Service Centre or a
qualified electrician.
Declaration of conformity
This product has been designed, manufactured and sold in
conformity to the following standards:
- safety objectives of "Low Voltage" Directive 73/23/EEC.
- protection requirements of “EMC” Directive 89/336/EEC
amended by Directive 93/68/EEC.
Troubleshooting guide
The hood does not work:
• Is the plug properly inserted in the power socket?
• Is there a power failure?
• Is the fuse blown?
The hood is not extracting efficiently:
• Is the right speed selected?
• Do the filters need cleaning or replacing?
• Are the air outlets blocked?
The light does not work:
• Does the bulb need replacing?
• Is the bulb correctly fitted?
• Is the fuse blown?
AFTER-SALES SERVICE
Before calling the After-sales Service
1. Check if you can fix the problem yourself (see ”Troubleshooting
guide”).
2. Switch the hood off and then on again to check if the problem
has gone.
3. If the problem persists, contact the After-sales Service.
Specify:
• the nature of the problem,
• the model of hood, stated on the data plate inside the hood,
accessible by removing the grease filters.
• your full address,
• your telephone number and area code.
• the service code (the number appearing below the word
SERVICE on the data plate inside the hood behind the grease
filter).
If any repairs are needed, contact an authorised Service Centre (to
ensure that only original spare parts are used and that repairs are
made correctly).
Failure to comply with these instructions may compromise the safety
and quality of the product.
61833043.fm Page 6 Thursday, April 6, 2006 9:14 AM
-
1
-
2
-
3
IKEA HOO E00 S is a versatile kitchen appliance that combines efficient odor and grease removal with elegant design. With its powerful extraction capabilities, it effectively eliminates fumes, smoke, and cooking odors, leaving your kitchen fresh and clean. The hood features adjustable extraction speeds, allowing you to customize its performance based on your cooking needs.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Whirlpool WSLESS 66 AS X User guide
-
Bauknecht DBAG 56 AS X User guide
-
-
Whirlpool AKR 1050 IX User guide
-
KitchenAid KEICD 10010 User guide
-
Whirlpool AKR 987 JA Program Chart
-
KINGSWOOD KGCH70X User guide
-
Bauknecht DDEI 5790 IN Program Chart
-
Ignis AKS 561 GY Program Chart
-