Shenzhen 3onedata Technology ES208G User manual

Brand
Shenzhen 3onedata Technology
Model
ES208G
Type
User manual
- 1 -
ES208G
Industrial Ethernet Switch
User Manual
Shenzhen 3onedata Technology Co., Ltd.
Tel: +86-755-26702668 Fax: +86-755-26703485
www.3onedata.com
Introduction
ES208G is a kind of gigabit unmanaged Industrial Ethernet switch,
it support 8 port 10/100/1000M RJ45 port, DC power supply
(12-48V). It adopted no fan, low power consumption design, IP40,
corrugate high strength iron shell, the performance is more
steadily. ES208G accorded with CE, FCC standard and Industrial
4 grades, DIN rail installation and wide operating temperature
(-25~70 ), it can satisfied some kinds of industrial environment,
it can provide reliable and quickly solution for your Ethernet
device.
Packing list
The unmanaged Ethernet switch is shipped with the following
items. If any of these items are missing or damaged, please
contact your customer service representative for assistance.
Industrial Ethernet Switch 1
User manual 1
DIN-Rail mounting kit 1
Warranty card 1
Feature
Support 8 ports 10Base-T/100Base-TX/1000 Base-TX
Support 10/100/1000M self-adaption
Support IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3ab
Support Store and forward
Support broadcast storm relieving
12 48VDC power input, power supply support non-polarity.
-25 70 working temperature
IP40 protect grade, high strength iron shell
DIN Rail installation
Panel layout
Vertical view and bottom view Front view
Rear view and Side view
1. Ground screw
2. Power input terminal block (3 bits)
3. Screw holes for Wall Mounting Kit
4. DIN-Rail mounting kit
5. 10/100/1000Base-T(X) port
6. PWR indicator
7. Gigabit Ethernet port indicator
Dimension
- 2 -
Unit (mm)
Power supply input
The switch provided 3 bit power supply input terminal block,
support DC input. Voltage input range is 12 48VDC (terminal
block defined as: V-, FG, V+). It can also work if connection
opposite.
Communication connector
10/100/1000BaseT(X) Ethernet port
The pinout of RJ45 port display as below, connect by UTP or STP.
The connect distance is no more than 100m. 1000Mbps is used
120Ω of UTP 5e; 100Mbps is used 120Ω of UTP 5; 10Mbps is
used 120Ω of UTP 3, 4, 5.
RJ 45 port support automatic MDI/MDI-X operation. That can
connect the PC, Server, Converter and HUB. Pin 1, 2, 3, 4, 5, 6, 7,
8 Corresponding connections in MDI. 1→3, 2→6, 3→1, 4→7,
5→8, 6→2, 7→4, 8→5, are used as cross wiring in the MDI-X
port of Converter and HUB. In MDI/MDI-X, 100/1000Base-TX
PIN defines is as follows:
PIN MDI MDI-X
1 BI_DA+/TX+ BI_DB+/RX+
2 BI_DA-/TX- BI_DB-/RX-
3 BI_DB+/RX+ BI_DA+/TX+
4 BI_DC+/ BI_DD+/
5 BI_DC-/ BI_DD-/
6 BI_DB-/RX- BI_DA-/TX-
7 BI_DD+/ BI_DC+/
8 BI_DD-/ BI_DC-/
Note 10Base-T/100Base-TX, “TX ”transmit data , “RX ”receive data ,
“ ”not use.
Gigabit MDI (straight-through cable)
Gigabit MDI-X (Cross over cable)
MDI/MDI-X auto connection makes switch easy to use for
customers without considering the type of network cable.
LED Indicator
LED indictor light on the front panel of product, the function of
each LED is described in the table as below.
System indication LED
LED State Description
PWR
ON Power is being supplied to power
input PWR input
OFF Power is not being supplied to
power input PWR input
LINK/ACT
(G1~G8)
ON Port connection regular.
Blinking Port connection active
OFF Port had no connection.
Installation
Before installation, confirm that the work environment meet the
installation require, including the power needs and abundant
space. Whether it is close to the connection equipment and other
equipments are prepared or not.
1. Avoid in the sunshine, keep away from the heat fountainhead or
the area where in intense EMI.
2. Examine the cables and plugs that installation requirements.
3. Examine whether the cables be seemly or not (less than 100m)
according to reasonable scheme.
4. Power: 12-48VDC power input
5. Environment: working temperature: -25 70
Storage Temperature: -40 85
Relative humidity 5% 95%
DIN Rail Installation
In order to use in industrial environments expediently, the product
adopt 35mm DIN-Rail installation, the installation steps as below:
1. Examine the DIN-Rail attachment
2. Examine DIN Rail whether be firm and the position is
1 8
- 3 -
suitability or not.
3. Insert the top of the DIN-Rail into the slot just below the
stiff metal spring.
4. The DIN-Rail attachment unit will snap into place as shown
below.
Wiring Requirements
Cable laying need to meet the following requirements,
1. It is needed to check whether the type, quantity and
specification of cable match the requirement before cable
laying;
2. It is needed to check the cable is damaged or not, factory
records and quality assurance booklet before cable laying;
3. The required cable specification, quantity, direction and
laying position need to match construction requirements, and
cable length depends on actual position;
4. All the cable cannot have break-down and terminal in the
middle;
5. Cables should be straight in the hallways and turning;
6. Cable should be straight in the groove, and cannot beyond the
groove in case of holding back the inlet and outlet holes.
Cables should be banded and fixed when they are out of the
groove;
7. User cable should be separated from the power lines. Cables,
power lines and grounding lines cannot be overlapped and
mixed when they are in the same groove road. When cable is
too long, it cannot hold down other cable, but structure in the
middle of alignment rack;
8. Pigtail cannot be tied and swerved as less as possible.
Swerving radius cannot be too small (small swerving causes
terrible loss of link). Its banding should be moderate, not too
tight, and should be separated from other cables;
9. It should have corresponding simple signal at both sides of the
cable for maintaining.
Specification
Technology
Standard: IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3ab
Flow control: IEEE802.3x, back pressure control
Exchange attribute
100M forward speed: 148810pps
1000M forward speed: 1488100pps
Transmit mode: store and forward
System exchange bandwidth: 16Gbps
MAC address table: 8K
Memory: 1Mbit
Interface
Gigabit Ethernet port: 10Base-T/100Base-TX/1000 Base-TX auto
speed control
Transfer distance
Twisted cable: 100M (standard CAT5/CAT5e cable)
LED indicator
Interface indicator: Link/ACT (G1~G8)
Power supply indicator: PWR
Power supply
Input Voltage: 24VDC (12~48VDC)
Type of input: 3 bits 7.62mm terminal block
Support non-polarity
Overload current protect: 4.0A
Consumption
No-load power consumption: 0.82W@24VDC
Full-load power consumption: 3.65W@24VDC
Working environment
Working temperature: -25 70
Storage temperature: -40 85
Relative Humidity: 5%~95 %( no condensation)
Mechanical Structure
Shell: IP40 protect grade, metal shell
Installation: DIN-Rail
Weight: 0.62kg
Size (W×H×D): 53mm×138mm×110mm
Industry Standard
EMI: FCC Part 15, CISPR (EN55022) class A
EMS: EN61000-4-2 (ESD), Level 2
EN61000-4-3 (RS), Level 2
EN61000-4-4 (EFT), Level 2
EN61000-4-5 (Surge), Level 2
EN61000-4-6 (CS), Level 2
EN61000-4-8, Level 2
Shock: IEC 60068-2-27
Free fall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Certification
CE, FCC, RoHS, UL508 (Pending)
Warranty: 3 years
  • Page 1 1
  • Page 2 2
  • Page 3 3

Shenzhen 3onedata Technology ES208G User manual

Brand
Shenzhen 3onedata Technology
Model
ES208G
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents