Contec SH-9008AT-POE NEW Reference guide

Contec
Brand
Contec
Model
SH-9008AT-POE NEW
Type
Reference guide

This manual is also suitable for

Contec SH-9008AT-POE NEW is an 8-port industrial switching HUB which conforms to the IEEE802.3ab (1000BASE-T) / IEEE802.3u (100BASE-TX) / IEEE802.3 (10BASE-T) standards, and is capable of PoE power supply based on IEEE802.3af, IEEE802.3at. By using a LAN cable of category 5 or greater, power can be supplied to PoE devices that conform to IEEE802.3af and IEEE802.3at.

Contec SH-9008AT-POE NEW is an 8-port industrial switching HUB which conforms to the IEEE802.3ab (1000BASE-T) / IEEE802.3u (100BASE-TX) / IEEE802.3 (10BASE-T) standards, and is capable of PoE power supply based on IEEE802.3af, IEEE802.3at. By using a LAN cable of category 5 or greater, power can be supplied to PoE devices that conform to IEEE802.3af and IEEE802.3at.

Reference Manual
CONTENTS
Industrial 8-port unmanaged Gigabit PoE Ethernet Switching HUB
SH-9008AT-POE
Introduction .................................................................. 4
Safety Precautions ...................................................... 9
Product Nomenclature and Function ............... 16
Setting Up ................................................................... 24
Appendix ...................................................................... 30
Customer Support and Inquiry ............................ 35
-
2
-
Table of Contents
Introduction ...................................................................... 4
1. Related Manuals ......................................................................................................................................................5
2. About the Product ..................................................................................................................................................6
3. Features ......................................................................................................................................................................7
4. Product Configuration List ..................................................................................................................................8
Safety Precautions ............................................................ 9
1. Safety Information ............................................................................................................................................... 10
2. Handling Precautions ......................................................................................................................................... 11
1. FCC PART 15 Class A Notice ...................................................................................................................... 13
2. EN55032Class A Notice .............................................................................................................................. 13
3. Usage limitation ................................................................................................................................................... 14
4. Environment ........................................................................................................................................................... 15
5. Inspection ............................................................................................................................................................... 15
6. Storage ..................................................................................................................................................................... 15
7. Disposal ................................................................................................................................................................... 15
Product Nomenclature and Function ........................... 16
1. Nomenclature of Product Components ..................................................................................................... 17
2. Description of Product Components ........................................................................................................... 18
1. LAN Port ........................................................................................................................................................... 18
2. Power Supply Connector ............................................................................................................................ 19
3. Power Failure Detection DIP Switch ....................................................................................................... 20
4. LED Indicator ................................................................................................................................................... 21
3. Connecting to Network ..................................................................................................................................... 22
1. Network Cable ................................................................................................................................................ 22
2. Connection Restrictions .............................................................................................................................. 23
Setting Up ....................................................................... 24
1. Power Supplies ..................................................................................................................................................... 25
2. Installation .............................................................................................................................................................. 26
1. Mounting on a DIN rail ............................................................................................................................... 26
2. Removing from a DIN Rail ......................................................................................................................... 27
3. Setting on the Wall ....................................................................................................................................... 28
4. Spacing between the system unit and any surrounding objects ............................................... 29
Appendix ........................................................................ 30
1. Hardware Specifications.................................................................................................................................... 31
2. Physical Dimensions ........................................................................................................................................... 33
-
3
-
Table of Contents
Customer Support and Inquiry ..................................... 35
1. Services .................................................................................................................................................................... 36
-
4
-
Introduction
This section provides necessary information of the product
such as the outline, bundled items and manuals before
actual use.
—
Introduction
—
SH-9008AT-POE Reference Manual
-
5
-
1. Related Manuals
The manuals related to the product are listed below.
Read them as necessary along with this document.
Must Read the Following Manuals.
Name
Purpose
Contents
How to get
Product Guide
Must read this after
opening the package.
This lists the product
configuration and describes
the precautions.
Included in the package
(Printed matter)
Reference Manual
(This document)
Read this when operating
the product.
This describes the hardware
aspects such as functions and
settings.
Download from
the Contec
website (PDF)
Download Manuals
Download the manuals accordingly from the following URL.
https://www.contec.com/download/
—
Introduction
—
SH-9008AT-POE Reference Manual
-
6
-
2. About the Product
This product is an 8-port industrial switching HUB which conforms to IEEE802.3ab (1000BASE-T)
/IEEE802.3u (100BASE-TX) /IEEE802.3 (10BASE-T) standard, and it is capable of PoE power supply
based on IEEE802.3af, IEEE802.3at.
By using a LAN cable of category 5 or greater, power can be supplied to PoE devices that conform
to IEEE802.3af and IEEE802.3at.
The functions including jumbo frames, AutoMDI / MDI-X, and auto negotiations are within.
Due to the fan-less design, this hub can be used in the places where the quietness or a longer lifetime
of the product is desired. Furthermore, a metal housing with excellent heat dissipation enables the
product to be operated in the temperature between -35°C and +70°C. The product can be set on
35mm-DIN rail or on the wall with the supplied brackets.
Carefully read this Reference Manual to connect the product with devices and establish the system.
—
Introduction
—
SH-9008AT-POE Reference Manual
-
7
-
3. Features
PoE power supply function based on IEEE802.3af,
IEEE802.3at
Power can be supplied to PoE devices that conform to IEEE802.3af, IEEE802.3at. Up to 30W per port and up to 120W * for all ports can
be powered.
*There is a limit to supply the power depending on the power input voltages.
Eight of 1000BASE-T ports are equipped
The product has eight ports which conform to IEEE802.3ab(1000BASE-T) / IEEE802.3u(100BASE-TX)/ IEEE802.3(10BASE-T).
Due to the fan-less design, this hub can be used in the places where the quietness or a longer lifetime of the product is desired.
Furthermore, a metal housing with excellent heat dissipation enables the product to be operated in the temperature between -35 °C and
+70 °C.
Capable of operating in a wide-ranged power inputs,
and features dual power support
The product is capable of operating in a wide range of DC power between 12 and 57VDC. Moreover, dual power supports the product
to continue to work even if one of the power supplies fails. Failures of the power supply can be seen with the LED on the front panel or
the failure detection relay circuit.
DIN rail mounting or Wall installation
With the supplied brackets, the product can be set on a 35mm-DIN rail or on the wall.
—
Introduction
—
SH-9008AT-POE Reference Manual
-
8
-
4. Product Configuration List
The product consists of the items listed below.
Check, with the following list, that your package is complete.
If you discover damaged or missing items, contact your retailer.
Product…1
Product Guide...1
Warranty Certificate...1
DIN-Rail Mounting
Bracket...1
(attached to the
product)
Power Connector...1
RJ45 Protection Cap...8
Screw…8
Wall Bracket...2
-
9
-
Safety Precautions
Understand the following definitions and precautions to
use the product safely.
Never fail to read them before using the product.
—
Safety Precautions
—
SH-9008AT-POE Reference Manual
-
10
-
1. Safety Information
This document provides safety information using the following symbols to prevent accidents
resulting in injury or death and the destruction of equipment and resources.
Understand the meanings of these labels to operate the equipment safely.
DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury or in property damage.
—
Safety Precautions
—
SH-9008AT-POE Reference Manual
-
11
-
2. Handling Precautions
WARNING
Always check that the power is turned off before connecting or disconnecting power cables.
Do not modify the product.
Do not use the product in locations exposed to a flammable or corrosive gas. It may cause
explosion, fire, electrical shock, or malfunction.
Do not allow this device to come into contact with foreign substances (metal particles,
flammable substances, liquids, etc.) This can cause fire or electrical shock.
Do not place this device in an unstable location or use incomplete mountings. This may cause
the device to fall.
Be sure to connect the product to the stipulated power supply voltage. Connecting to a
different voltage might cause a fire or electrical shock.
If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
This product is not intended for use in aerospace, space, nuclear power, medical equipment,
or other applications that require a very high level of reliability. Do not use the product in
such applications.
If using this product in applications where safety is critical such as in railways, automotive, or
disaster prevention or security systems, please contact your retailer.
CAUTION
Do not use or store the product in a location exposed to extremely high or low temperature
or susceptible to a rapid temperature changes.
Example: - Exposure to direct sun - In the vicinity of a heat source
Do not use the product in extremely humid or dusty locations. It is extremely dangerous to
use this product with its interior penetrated by water or any other fluid or conductive dust. If
this product must be used in such an environment, install it on a dust-proof control panel, for
example.
Avoid using or storing the product in locations subject to shock or vibration that exceeds
range of specification.
When transporting the product, take suitable measures to avoid applying shock or vibration
directly to the product.
Impact resistance: 15G (11ms) below.
Use the product in the specified operating condition (temperature, humidity, vibration and
shock).
The product should always be grounded (earth).
—
Safety Precautions
—
SH-9008AT-POE Reference Manual
-
12
-
Avoid installing in the place where ventilation of the product may compromise. Insufficient
aeration could heat up the product and lead to malfunctions or damages.
Do not use the product in the vicinity of devices that generate strong magnetic force or noise.
Such products will cause the product to malfunction (stop, reboot).
Do not use or store the product in the presence of chemicals.
When removing connectors or cables, always unplug the power cables connected to the
product first.
Do not modify the product. CONTEC will bear no responsibility for any problems, etc.,
resulting from modifying the product.
In the event of failure or abnormality (foul smells or excessive heat generation), un-plug the
power cables from an electric outlet immediately and contact your retailer.
To connect with peripherals, use a grounded, shielded cable.
To clean the product, wipe it gently with a soft cloth dampened with either water or mild
detergent. Do not use chemicals or a volatile solvent, such as benzene or thinner, to prevent
the paint to be scraped or discolored.
When connecting cables, first check the shapes of connectors, and then insert them in the
correct orientation. After they are connected, do not put too much load on the connected
part. Doing so may result in poor contact or damage to the product and the connected part.
To suppress noise emission from the product, set a ferrite core to the power cable and LAN
cable (refer to page 18 and 19).
Do not touch metal parts or terminals with your hands when the product is in operation.
Otherwise, the product may malfunction, or cause failure.
Do not touch the product or connectors with a wet hand to avoid electric shock.
The specifications of the product are subject to change without notice for enhancement and
quality improvement. Even when using the product continuously, be sure to read the manual
in the CONTEC's website and understand the contents.
When the product is used in a place that is affected by overcurrent or overvoltage (lightning
surge), select appropriate surge protection device for all of the route (Power line, signal line,
earth, etc.). Consult with the specialist regarding selecting, purchasing, and setting the surge
protection device.
When disposing of the product, follow the disposal procedures stipulated under the relevant
laws and municipal ordinances.
The ferrite core must be installed in interface connecting cable so that the product may suit
the above-mentioned standard.
Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever
(Including damages for loss of business profits) arising out of the use or inability to use the
CONTEC product or the information contained herein.
—
Safety Precautions
—
SH-9008AT-POE Reference Manual
-
13
-
1. FCC PART 15 Class A Notice
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
2. EN55032Class A Notice
Warning:
Operation of this equipment in a residential environment could cause radio interference.
CAUTION
The product standard applies to the main body only.
—
Safety Precautions
—
SH-9008AT-POE Reference Manual
-
14
-
3. Usage limitation
This product has not been developed or manufactured to be used in systems including the
equipment which is directly related to human lives *1 or the equipment which involves human safety
and may significantly affect the maintenance of public functions *2. Therefore, do not use the product
for such purposes.
*1: Medical devices such as life-support equipment and devices used in an operating theater.
*2: Main control systems at nuclear power stations, safety maintenance systems at nuclear facilities,
other important safety-related systems, operation control systems within group transport systems,
air-traffic control systems, etc.
—
Safety Precautions
—
SH-9008AT-POE Reference Manual
-
15
-
4. Environment
Use this product in the following environment. If used in an unauthorized environment, the board
may overheat, malfunction, or cause a failure.
Operating temperature
-35 - +50ºC
Humidity
5 - 95%RH (No condensation)
Corrosive gases
None
Floating dust particles
Not to be excessive
5. Inspection
Inspect the product periodically to use it safely.
Check the ventilation slit and make sure that it is not blocked by dust or foreign matter.
6. Storage
When storing this product, keep it in its original packing form.
Put this product in the storage bag.
Wrap it in the packing material, and then put it in the box.
Store the package at room temperature at a place free from direct sunlight, moisture, shock,
vibration, magnetism, and static electricity.
7. Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws
and municipal ordinances.
-
16
-
Product Nomenclature
and Function
This section describes product component names and their
functions, pin assignment of each connector.
—
Product Nomenclature and Function
—
SH-9008AT-POE Reference Manual
-
17
-
1. Nomenclature of Product Components
Component names of the product are shown in the figure below.
No.
Name
No.
Name
1
Power LED
6
Bracket Screw Holes for DIN-rail
Installation
2
Power Failure Detection Relay LED
7
Bracket Screw Holes for Wall Installation (M3)
3
Link / Act LED
8
Power Supply Connector:
PWR1, PWR2, Power Failure Detection
Relay
4
PoE LED
9
Power Failure Detection DIP Switch
5
LAN Port
Screw Holes for Grounding Wire (M3)
—
Product Nomenclature and Function
—
SH-9008AT-POE Reference Manual
-
18
-
2. Description of Product Components
Components such as connectors, switches are described.
1. LAN Port
This product has 8 LAN ports.
Pin Assignment
Pin number
Description
1
BI_DA+ with PoE power Output +
2
BI_DA- with PoE power Output -
3
BI_DB+ with PoE power Output +
4
BI_DC+
5
BI_DC-
6
BI_DB- with PoE power Output -
7
BI_DD+
8
BI_DD-
Setting Ferrite Core
To suppress noise emission from the product, set a ferrite core on LAN cable (0 turn) about two
centimeters away from the LAN port.
Recommended ferrite core: E04SR170730A (SEIWA)
—
Product Nomenclature and Function
—
SH-9008AT-POE Reference Manual
-
19
-
2. Power Supply Connector
Use the 6-pin connector to connect to external power.
Pin Assignment
Pin number
Signal name
Description
1
V1+
PWR-1 power supply (12 - 57VDC±5%)
2
V1-
PWR-1 power supply (GND)
3
FCOM
Power failure detection relay terminal (common)
4
FNC
Power failure detection relay terminal (normally closed)
5
V2
PWR-2 power supply (12 - 57VDC±5%)
6
V2-
PWR-2 power supply (GND)
This hub can be operated by supplying the power to either PWR-1 or PWR-2.
Moreover, the operation can be continued even when PWR-1 or PWR-2 is turned off while the power
is simultaneously supplied to them.
Setting Ferrite Core
To suppress noise emission from the product, set a ferrite core on the cable (1 turn) about two
centimeters away from the power connector.
Recommended ferrite core: E04SR401938 (SEIWA)
—
Product Nomenclature and Function
—
SH-9008AT-POE Reference Manual
-
20
-
3. Power Failure Detection DIP Switch
Power output failure can be detected with the set of the DIP switch.
The relay pins (pin-3 and pin-4) of the power connector are open in normal operation mode, but
they are closed before the power is supplied or when the power output of the PWR-1 or PWR-2
drops.
DIP-1
DIP-2
Description
OFF
ON
Relays are always open when the product is used.
OFF
ON
The relay closes when the power failure of PWR-1 drops below 7V.
ON
OFF
The relay closes when the power failure of PWR-2 drops below 7V.
ON
OFF
The relay closes when the power of PWR-1 or PWR-2 drops below 7V.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Contec SH-9008AT-POE NEW Reference guide

Contec
Brand
Contec
Model
SH-9008AT-POE NEW
Type
Reference guide
This manual is also suitable for

Contec SH-9008AT-POE NEW is an 8-port industrial switching HUB which conforms to the IEEE802.3ab (1000BASE-T) / IEEE802.3u (100BASE-TX) / IEEE802.3 (10BASE-T) standards, and is capable of PoE power supply based on IEEE802.3af, IEEE802.3at. By using a LAN cable of category 5 or greater, power can be supplied to PoE devices that conform to IEEE802.3af and IEEE802.3at.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents