IEI Integration HTB-150-N6210 User manual

HTB-150-N6210 Medical Embedded System

Page i

User Manual

HTB-150-N6210 Box PC

MODEL: MODEL:

HTB-150-N6210

Medical Embedded System with Intel® Celeron® N6210 CPU,

LPDDR4x, 32 GB eMMC, RS-232, Dual GbE LAN,

USB 3.2 Gen 2, M.2, HDMI and RoHS

Rev. 1.00 – September 25, 2023

HTB-150-N6210 Medical Embedded System

Page ii

Revision

Date

Version

Changes

September 25, 2023

1.00

Initial release

HTB-150-N6210 Medical Embedded System

Page iii

Copyright

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or

other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

CONTACT INFORMATION

IEI Integration Corp.

Address:

No. 29, Zongxing Rd., Xizhi Dist.,

New Taipei City 221, Taiwan

Phone:

+886-2-8691-6798

Fax:

+886-2-6616-0028

Web Site:

www.ieiworld.com

Sales Email:

[email protected]

HTB-150-N6210 Medical Embedded System

Page iv

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the

equipment or result in personal injury. Warnings should be taken seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of

losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical information.

These messages should be read carefully as any directions or instructions

contained therein can help avoid making mistakes.

 
 
HTB-150-N6210 Medical Embedded System 
 
Page v 
Table of Contents 
INTRODUCTION .......................................................................................................... 1 
1 OVERVIEW .................................................................................................................. 2 
2 FEATURES ................................................................................................................... 2 
3 FRONT PANEL............................................................................................................. 3 
4 REAR PANEL .............................................................................................................. 3 
5 BOTTOM PANEL ......................................................................................................... 4 
6 TECHNICAL SPECIFICATIONS ...................................................................................... 5 
7 DIMENSIONS ............................................................................................................... 7 
UNPACKING ................................................................................................................. 8 
1 UNPACKING ................................................................................................................ 9 
2 PACKING LIST ............................................................................................................ 9 
INSTALLATION .......................................................................................................... 11 
1 SAFETY PRECAUTIONS ............................................................................................. 12 
2 ANTI-STATIC PRECAUTIONS ...................................................................................... 13 
3 INSTALLATION PRECAUTIONS ................................................................................... 15 
4 GBE CONNECTION ................................................................................................... 15 
5 RS-232 SERIAL DEVICE CONNECTION ..................................................................... 16 
6 AT/ATX MODE SELECTION ...................................................................................... 17 
7 MOUNTING THE SYSTEM .......................................................................................... 17 
7.1 Using Mounting Brackets ................................................................................ 17 
7.2 VESA Mounting ................................................................................................ 19 
8 POWER-ON PROCEDURE ........................................................................................... 20 
8.1 Installation Precautions ................................................................................... 20 
9 CLEAR CMOS .......................................................................................................... 21 
10 RESET THE SYSTEM ................................................................................................ 21 
11 AVAILABLE DRIVERS .............................................................................................. 22 
11.1 Driver Download ............................................................................................ 22 
12 SYSTEM MAINTENANCE ......................................................................................... 24 

 
 
HTB-150-N6210 Medical Embedded System 
 
Page vi 
BIOS .............................................................................................................................. 25 
1 INTRODUCTION ......................................................................................................... 26 
1.1 Starting Setup ................................................................................................... 26 
1.2 Using Setup ...................................................................................................... 27 
1.2.1 Keyboard Navigation ................................................................................ 27 
1.2.2 Touch Navigation ...................................................................................... 28 
1.3 Getting Help ..................................................................................................... 28 
1.4 Unable to Reboot after Configuration Changes .............................................. 29 
1.5 BIOS Menu Bar ................................................................................................ 29 
2 MAIN ........................................................................................................................ 30 
3 ADVANCED ............................................................................................................... 31 
3.1 CPU Configuration .......................................................................................... 32 
3.2 Trusted Computing ........................................................................................... 34 
3.3 IT5571 Super IO Configuration ....................................................................... 35 
3.3.1 Serial Port 1 Configuration ....................................................................... 36 
3.3.2 Serial Port 2 Configuration ....................................................................... 37 
3.4 IT5571 H/W Monitor ........................................................................................ 38 
3.5 RTC Wake Settings ........................................................................................... 39 
3.6 Serial Port Console Redirection ...................................................................... 40 
3.7 Network Stack Configuration ........................................................................... 41 
3.8 NVMe Configuration ........................................................................................ 42 
4 CHIPSET ................................................................................................................... 43 
4.1 System Agent (SA) Configuration .................................................................... 44 
4.1.1 Memory Configuration ............................................................................. 45 
4.1.2 Graphics Configuration ............................................................................. 46 
4.2 PCH-IO Configuration .................................................................................... 47 
4.2.1 PCI Express Configuration ....................................................................... 49 
4.2.2 SATA Configuration .................................................................................. 50 
4.2.3 HD Audio Configuration ........................................................................... 51 
5 SECURITY ................................................................................................................. 52 
6 BOOT ........................................................................................................................ 53 
7 SAVE & EXIT ............................................................................................................ 53 
A REGULATORY COMPLIANCE .............................................................................. 55 
B PRODUCT DISPOSAL .............................................................................................. 60 

HTB-150-N6210 Medical Embedded System

Page vii

C MAINTENANCE AND CLEANING PRECAUTIONS .......................................... 62

C.1.1 Maintenance and Cleaning ............................................................................. 64

C.1.2 Cleaning Tools ................................................................................................. 64

D SYMBOL DEFINITIONS .......................................................................................... 65

E WATCHDOG TIMER ................................................................................................. 67

F ERROR BEEP CODE ................................................................................................. 70

F.1 PEI BEEP CODES ...................................................................................................... 71

F.2 DXE BEEP CODES .................................................................................................... 71

G HAZARDOUS MATERIALS DISCLOSURE ......................................................... 72

G.1 ROHS II DIRECTIVE (2015/863/EU) ....................................................................... 73

G.2 CHINA ROHS ........................................................................................................... 74

HTB-150-N6210 Medical Embedded System

Page viii

List of Figures

Figure 1-1: HTB-150-N6210 Medical Embedded System ............................................................ 2

Figure 1-2: Front Panel .................................................................................................................. 3

Figure 1-3: Rear Panel .................................................................................................................... 3

Figure 1-4: Bottom Panel ............................................................................................................... 4

Figure 1-5: Dimensions (mm) ........................................................................................................ 7

Figure 3-1: Ethernet Connector ................................................................................................... 16

Figure 3-2: AT/ATX Switch Location ........................................................................................... 17

Figure 3-3: Mounting Bracket Retention Screws ...................................................................... 17

Figure 3-4: Mounting Dimensions ............................................................................................... 18

Figure 3-5: VESA Mounting Retention Screw Holes ................................................................. 19

Figure 3-6: Power Button and Power LED ................................................................................. 20

Figure 3-7: Clear CMOS Button ................................................................................................... 21

Figure 3-8: Reset Button Location .............................................................................................. 21

Figure 3-9: IEI Resource Download Center ................................................................................ 22

HTB-150-N6210 Medical Embedded System

Page ix

List of Tables

Table 1-1: Technical Specifications .............................................................................................. 6

Table 2-1: Package List ................................................................................................................ 10

Table 3-1: Ethernet Connector Pinouts ...................................................................................... 15

Table 3-2: Connector LEDs .......................................................................................................... 16

Table 3-3: RS-232 Serial Port Pinouts ........................................................................................ 16

Table 4-1: BIOS Navigation Keys ................................................................................................ 27

Table 4-2: BIOS On-screen Navigation Keys ............................................................................. 28

 
 
HTB-150-N6210 Medical Embedded System 
 
Page x 
List of BIOS Menus 
BIOS Menu 1: Main ....................................................................................................................... 30 
BIOS Menu 2: Advanced .............................................................................................................. 31 
BIOS Menu 3: CPU Configuration ............................................................................................... 32 
BIOS Menu 4: Trusted Computing .............................................................................................. 34 
BIOS Menu 5: IT5571 Super IO Configuration ........................................................................... 35 
BIOS Menu 6: Serial Port 1 Configuration Menu ....................................................................... 36 
BIOS Menu 7: Serial Port 2 Configuration Menu ....................................................................... 37 
BIOS Menu 8: IT5571 H/W Monitor .............................................................................................. 38 
BIOS Menu 9: RTC Wake Settings .............................................................................................. 39 
BIOS Menu 10: Serial Port Console Redirection ....................................................................... 40 
BIOS Menu 11: Network Stack Configuration ............................................................................ 41 
BIOS Menu 12: NVMe Configuration ........................................................................................... 42 
BIOS Menu 13: Chipset ................................................................................................................ 43 
BIOS Menu 14: System Agent (SA) Configuration .................................................................... 44 
BIOS Menu 15: Memory Configuration ....................................................................................... 45 
BIOS Menu 16: Graphics Configuration ..................................................................................... 46 
BIOS Menu 17: PCH-IO Configuration ........................................................................................ 47 
BIOS Menu 18: PCI Express Configuration ............................................................................... 49 
BIOS Menu 19: SATA Configuration ........................................................................................... 50 
BIOS Menu 20: HD Audio Configuration .................................................................................... 51 
BIOS Menu 21: Security ............................................................................................................... 52 
BIOS Menu 22: Boot ..................................................................................................................... 53 
BIOS Menu 23: Save & Exit .......................................................................................................... 54 

HTB-150-N6210 Medical Embedded System

Page 1

Chapter

1

1 Introduction

HTB-150-N6210 Medical Embedded System

Page 2

1.1 Overview

Figure 1-1: HTB-150-N6210 Medical Embedded System

The HTB-150-N6210 fanless medical embedded system is powered by Intel® Celeron®

N6210 processor and onboard 8GB LPDDR4x. It is designed for space-constrained

applications that require reliable operating at low power consumption.

The compact-size HTB-150-N6210 offers multiple I/O interfaces, giving you flexibility and

functionality in a small package. Interfaces include four USB 3.2 Gen 2 (10Gb/s) ports,

one RS-232 port, and one HDMI output port. In additional to two GbE ports, an M.2 A-key

slot is also available for installing the optional Wi-Fi 6E module to provide wireless

communication.

The HTB-150-N6210 is built-in with 32GB eMMC for storage, and it is capable of

supporting one M.2 PCIe SSD module via 2280 M-key slot.

1.2 Features

The HTB-150-N6210 has the following features

 Compact fanless medical device with great computing at low power

 Supports Intel® Celeron® N6210 processor, burst up to 2.6 GHz

 Onboard 8 GB power-efficiency LPDDR4x memory

 Reliable onboard 32 GB eMMC for storage

 Four USB 3.2 Gen2 (10Gb/s) ports provide fast peripheral connections

HTB-150-N6210 Medical Embedded System

Page 3

1.3 Front Panel

An overview of the front panel is shown in 691H691H568HFigure 1-2 below.

Figure 1-2: Front Panel

1.4 Rear Panel

692H692H569H The rear panel of the HTB-150-N6210 provides access to the following external I/O

connectors, button and switches as shown in Figure 1-3.

Figure 1-3: Rear Panel

HTB-150-N6210 Medical Embedded System

Page 4

1.5 Bottom Panel

The bottom panel has four screw holes for VESA 75 mounting.

Figure 1-4: Bottom Panel

HTB-150-N6210 Medical Embedded System

Page 5

1.6 Technical Specifications

The specifications for the Intel based medical embedded systems are listed below.

HTB-150-N6210

CPU

Intel® Celeron® Processor N6210

LAN

2 x Intel® I225-V Ethernet controllers

System Memory

On-board 8GB LPDDR4x

Storage

On-board 32GB eMMC

Expansion

1 x M.2 2230 A key slot (PCIe + USB)

1 x M.2 2280 M key slot (PCIe)

Wireless

Wi-Fi IEEE 802.11a/b/g/n/ax, Intel® Wi-Fi 6E AX210 (optional)

Bluetooth v5.2

Rear I/O

1 x 12V DC jack

1 x RS-232

1 x HDMI out

2 x GbE LAN

Front I/O

1 x Power on/off switch (with power LED)

1 x Reset button

1 x Clear CMOS

1 x ATX/AT switch

4 x USB 3.2 Gen 2 (Type A) (5V / 0.9A)

LED Indicator

Power LED

HDD LED

Thermal

Fanless

Construction Material

Extruded aluminum alloys

Mounting

VESA 75 x 75 mm

Power Requirement

12 V DC

HTB-150-N6210 Medical Embedded System

Page 6

Power Adapter

65 W FSP FSP065M-DHA medical-grade power adapter

(P/N: 63040-010065-500-RS)

Input: 100 V AC - 240 V AC, 50 Hz - 60 Hz, 2.0 A – 1.0 A

Output: 12 V 5.42 A

Operating Shock

5G peak acceleration (11ms duration)

Non-operating Shock

15G peak acceleration (11ms duration)

Vibration

1G

Storage/Transportation

Temperature

-20ºC - 60ºC

Humidity

10% - 95% (non-condensing)

Pressure

700 hPa - 1060 hPa

Operating

Temperature

0ºC - 40ºC

Humidity

20% - 80% (non-condensing)

Pressure

700 hPa - 1060 hPa

Weight (Net/Gross)

0.69 kg / 1.84 kg

Dimensions (W x D x H)

137 mm x 102.8 mm x 36 mm

Supported OS

Windows 10; Windows 11; Linux Ubuntu

Safety/ECM

CE, FCC Class B Part18, FCC Class B Part15,

UL 60601-1, IEC/EN 60601-1, IEC/EN 60601-1-2

Table 1-1: Technical Specifications

HTB-150-N6210 Medical Embedded System

Page 7

1.7 Dimensions

The dimensions of the HTB-150-N6210 are shown in 688H688H567HFigure 1-5.

Figure 1-5: Dimensions (mm)

HTB-150-N6210 Medical Embedded System

Page 8

Chapter

2

2 Unpacking

HTB-150-N6210 Medical Embedded System

Page 9

2.1 Unpacking

To unpack the medical embedded system, follow the steps below:

Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

external (second) box.

Step 2: Open the external (second) box.

Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

internal (first) box.

Step 4: Lift the system out of the boxes.

Step 5: Remove both polystyrene ends, one from each side.

Step 6: Make sure all the components listed in the packing list are present.

Step 0:

2.2 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do

not proceed with the installation. Contact the IEI reseller or vendor the

HTB-150-N6210 was purchased from or contact an IEI sales

representative directly by sending an email to 326H378H[email protected].

The HTB-150-N6210 medical embedded system is shipped with the following

components:

HTB-150-N6210 Medical Embedded System

Page 10

Quantity

Item

Image

1

HTB-150-N6210 medical embedded

system

1

Power cord

1

Medical grade power adapter

63040-010065-500-RS

(FSP FSP065M-DHA, 65W)

2

Mounting brackets

4

Mounting bracket retention screws

(M3*6)

4

VESA mount screws (M4*8)

Table 2-1: Package List

Page is loading ...

IEI Integration HTB-150-N6210 User manual

IEI Integration HTB-150-N6210 User manual

Related papers

Other documents