Charge device using built-in charge cable:
Connect attached micro-USB charge cable (1) to any micro-USB device.
For Apple Lightning devices, use included 8-pin connector adapter (3).
Press power button (5) to begin charging. Monitor charge status via screen icon on your device.
To stop charging, remove cable from your device.
Charge device using your own charge cable:
Connect USB charge cable included with your own device to 2.1A Output Port (2) on
Power Bank.
Press power button (5) to begin charging. Monitor charge status via screen icon on
your device.
To stop charging, remove cable from your device.
*Note: Power Bank LEDs remain lit while device is charging and show remaining battery capacity.
When device is full, Power Bank continues to safely trickle charge device. When charge cable is
removed, Power Bank shuts off within 10-20 seconds
Charge 10000 2-Port
Power Bank:
Connect USB/micro-USB charge cable (7)
to micro-USB IN port (4).
Connect/charge via any powered USB port.
Use USB/AC adapter (not included) for faster
results.
Four LEDs (6) flash in 25% increments and remain
solid when corresponding capacity is reached.
*Note: LEDs may not provide an accurate reading
while battery is recharging. For optimum performance,
make sure all LEDs have stopped flashing and remain
solid to ensure full charge capacity. Total recharge
time (0% - 100%) = about 13 hours.
No tandem charge — disconnect devices before
recharging Power Bank.
3
Thank you for purchasing the RichardSolo 10000 mAh 2-Port Power Bank. Please read these instructions before operation
and save for future reference.
10000 mAh 2-Port Power Bank
INSTRUCTION MANUAL
54
6
1
3
2
OUT1 - Built-in micro-USB output cable (5V 1A)
OUT2 - USB output port (5V 2.1A)
Micro-USB/Lightning 8-pin adapter located behind
micro-USB cable (1)
IN - Micro-USB input port (5V 1A)
Power button
4 LED charge capacity indicators (25%, 50%, 75%, 100%)
USB/micro-USB charge cable (Not shown in diagram)
1
2
3
4
5
6
7
Check remaining
charge capacity:
Tap/release power button (5)
to check remaining power
bank charge capacity:
1 LED flashing = less than
25%; 1 LED solid = about
25%; 2 LEDs = about 50%;
3 LEDs = about 75%; 4 LEDs
= about 75-100%.
Specifications:
Capacity: 10000 mAh
Cell Type: Li-polymer battery
Input: DC 5V 1A
Port 1 Output: DC 5V 1A
(built-in micro-USB cable)
Port 2 Output: DC 5V 2.1A
Size: 5.79" x 3.0" x 0.55"
(14.7 x 7.7 x 1.4 cm)
Weight: 10.0 oz. (283.5 g)
USB Compatibility:
Port 1 (1A): built-in cable for
micro-USB devices + Lightning
adapter for 8-pin Apple devices
Port 2 (2.1A): iPhone/iPod,
smartphones, MP3 players,
iPad/tablets (use your own
cable)
Package Contents:
10000 mAh 2-Port Li-polymer
battery
USB/micro-USB charge cable
Instructions
1
2
1
1
2
2
3
3
4
10000 mAh 2-Port Power Bank
INSTRUCTION MANUAL
Continue
Safety Instructions
Read all instructions and warnings prior to using this product. Failure to read and follow these safety
instructions could result in fire, explosion, electrical shock or other hazard causing serious and/or fatal
injury and/or property damage.
Do not modify, disassemble, open, drop,
crush, puncture, or shred this product
Do not expose this product to rain or water
Avoid excessive heat (open flame,
sunlight, etc.)
Keep away from high voltage devices
This product is not a toy — keep away from
children
Maintenance:
Do not store in a depleted state
— battery power cells can be damaged
Charge Power Bank at least once per
month when not in use.
Keep unit dry — avoid damp conditions
and corrosive material.
Do not clean with harsh chemicals,
soaps or detergents
1
2
3
4
5
1
2
3
4
Questions? Please email us at: RichardSoloHelp@gmail.com 2301 Kerner Blvd. Suite C, San Rafael, CA 94901 USA www.RichardSolo.com
/
