Casio CTK-581 User manual

WK3200/3700-E-1

E

USER’S GUIDE

738A-E-002A

CASIO Europe GmbH

Bornbarch 10, 22848 Norderstedt, Germany

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas).

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Important!

Please note the following important information before using this product.

• Before using the optional AD-5 Adaptor to power the unit, be sure to check the AC Adaptor

for any damage first. Carefully check the power cord for breakage, cuts, exposed wire and

other serious damage. Never let children use an AC adaptor that is seriously damaged.

• Never attempt to recharge batteries.

• Do not use rechargeable batteries.

• Never mix old batteries with new ones.

• Use recommended batteries or equivalent types.

• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated

near the battery compartment.

• Replace batteries as soon as possible after any sign they are getting weak.

• Do not short-circuit the battery terminals.

• The product is not intended for children under 3 years.

• Use only CASIO AD-5 adaptor.

• The AC adaptor is not a toy.

• Be sure to disconnect the AC adaptor before cleaning the product.

This mark applies in EU countries only.

E-1

Safety Precautions

Congratulations on your selection of the CASIO

electronic musical instrument.

• Before using the instrument, be sure to carefully

read through the instructions contained in this

manual.

• Please keep all information for future reference.

Symbols

Various symbols are used in this user’s guide and on

the product itself to ensure that the product is used

safely and correctly, and to prevent injury to the user

and other persons as well as damage to property.

Those symbols along with their meanings are shown

below.

DANGER

This symbol indicates information that, if ignored

or applied incorrectly, creates the danger of death

or serious personal injury.

WARNING

This indication stipulates matters that have the risk

of causing death or serious injury if the product is

operated incorrectly while ignoring this indication.

CAUTION

This indication stipulates matters that have the risk

of causing injury as well as matters for which there

is the likelihood of occurrence of physical damage

only if the product is operated incorrectly while

ignoring this indication.

738A-E-003A

Symbol Examples

This triangle symbol ( ) means that the

user should be careful. (The example at

left indicates electrical shock caution.)

This circle with a line through it (

)

means that the indicated action must not

be performed. Indications within or

nearby this symbol are specifically

prohibited. (The example at left indicates

that disassembly is prohibited.)

The black dot (

) means that the

indicated action must be performed.

Indications within this symbol are actions

that are specifically instructed to be

performed. (The example at left indicates

that the power plug must be unplugged

from the electrical socket.)

WK3200_e_01-09.p65 05.3.15, 6:16 PM1

E-2

738A-E-004A

Safety Precautions

● Never touch the AC adaptor while your

hands are wet.

Doing so creates the risk of electric shock.

● Use the AC adaptor where it will not be

splashed with water. Water creates the

risk of fire and electric shock.

● Do not place a vase or any other container

filled with liquid on top of the AC

adaptor. Water creates the risk of fire and

electric shock.

Batteries

Misuse of batteries can cause them to leak,

resulting in damage to nearby objects, or to

explode, creating the risk of fire and

personal injury. Always make sure you

observe the following precautions.

• Never try to take batteries apart or allow

them to become shorted.

• Never expose batteries to heat or dispose

of them by incineration.

• Never mix old batteries with new ones.

• Never mix batteries of different types.

• Do not charge the batteries.

• Make sure the positive (+) and negative

(–) ends of the batteries are facing

correctly.

Do not incinerate the product.

Never throw the product into fire.

Doing so can cause it to explode, creating

the risk of fire and personal injury.

Water and Foreign Matter

Water, other liquids, and foreign matter

(such as pieces of metal) getting into the

product create the risk of fire and electric

shock. Take the following steps

immediately.

1. Turn off power.

2. If you are using the AC adaptor for

power, unplug it from the wall outlet.

3. Contact your original retailer or an

authorized CASIO Service Provider.

Disassembly and Modification

Never try to take this product apart or

modify it in any way. Doing so creates the

risk of electric shock, burn injury, or other

personal injury. Leave all internal

inspection, adjustment, and maintenance up

to your original retailer or authorized

CASIO Service Provider.

DANGER

Alkaline Batteries

Perform the following steps immediately if

fluid leaking from alkaline batteries ever

gets into your eyes.

1. Do not rub your eyes! Rinse them with

water.

2. Contact your physician immediately.

Leaving alkaline battery fluid in your eyes

can lead to loss of sight.

WARNING

Smoke, Strange Odor, Overheating

Continued use of the product while it is

emitting smoke, a strange odor, or heat

creates the risk of fire and electric shock.

Take the following steps immediately.

1. Turn off power.

2. If you are using the AC adaptor for

power, unplug it from the wall outlet.

3. Contact your original retailer or an

authorized CASIO Service Provider.

AC Adaptor

● Misuse of the AC adaptor creates the risk

of fire and electric shock. Always make

sure you observe the following

precautions.

• Be sure to use only the AC adaptor

that is specified for this product.

• Use only a power source whose voltage

is the within the rating marked on the

AC adaptor.

• Do not overload electrical outlets and

extension cords.

● Misuse of the AC adaptor’s electric cord

can damage or break it, creating the risk

of fire and electric shock. Always make

sure you observe the following

precautions.

• Never place heavy objects on the cord

or subject it to heat.

• Never try to modify the cord or subject

it to excessive bending.

• Never twist or stretch the cord.

• Should the electric cord or plug become

damaged, contact your original retailer

or authorized CASIO Service Provider.

WK3200_e_01-09.p65 05.3.15, 6:16 PM2

E-3

Safety Precautions

CAUTION

AC Adaptor

● Misuse of the AC adaptor creates the

risk of fire and electric shock. Always

make sure you observe the following

precautions.

• Do not locate the electric cord near a

stove or other sources of heat.

• Never pull on the cord when

unplugging from the electrical outlet.

Always grasp the AC adaptor when

unplugging.

● Misuse of the AC adaptor creates the

risk of fire and electric shock. Always

make sure you observe the following

precautions.

• Insert the AC adaptor into the wall

outlet as far as it will go.

• Unplug the AC adaptor from the wall

outlet during lightening storms or

before leaving on a trip or other long-

term absence.

• At least once a year, unplug the AC

adaptor from the wall outlet and wipe

away any dust that is built up in the

area around the prongs of the plug.

Relocating the Product

Before relocating the product, always

unplug the AC adaptor from the wall outlet

and disconnect all other cables and

connecting cords. Leaving cords connected

creates the risk of damage to the cords, fire,

and electric shock.

Cleaning

Before cleaning the product, always unplug

the AC adaptor from the wall outlet first.

Leaving the AC adaptor plugged in creates

the risk of damage to the AC adaptor, fire,

and electric shock.

Batteries

Misuse of batteries can cause them to leak

resulting in damage to nearby objects, or to

explode, creating the risk of fire and

personal injury. Always make sure you

observe the following precautions.

• Use only batteries that are specified for

use with this product.

• Remove batteries from the product if you

do not plan to use it for a long time.

738A-E-005A

Dropping and Impact

Continued use of this product after it has

been damaged by dropping or subjecting it

to strong impact creates the risk of fire and

electric shock. Take the following steps

immediately.

1. Turn off power.

2. If you are using the AC adaptor for

power, unplug it from the wall outlet.

3. Contact your original retailer or an

authorized CASIO Service Provider.

Plastic Bags

Never place the plastic bag the product

comes in over your head or in your mouth.

Doing so creates the risk of suffocation.

Particular care concerning this precaution

is required where small children are

present.

Keep off of the product and stand.*

Climbing onto the product or stand can

cause it to tip over or become damaged.

Particular care concerning this precaution

is required where small children are

present.

Location

Avoid locating the product on an unstable

stand, on an uneven surface, or any other

unstable location. An unstable location can

cause the product to fall over, creating the

risk of personal injury.

WK3200_e_01-09.p65 05.3.15, 6:16 PM3

E-4

738A-E-006A

Safety Precautions

Connectors

Connect only the specified devices and

equipment to the product’s connectors.

Connection of a non-specified device or

equipment creates the risk of fire and

electric shock.

Location

Avoid the following locations for this

product. Such locations create the risk of

fire and electric shock.

• Areas subject to high humidity or large

amounts of dust.

• In food preparation areas or other areas

subject to oil smoke.

• Near air conditioning equipment, on a

heated carpet, in areas exposed to direct

sunlight, inside of a vehicle parked in the

sun, or any other area that subjects the

product to high temperatures.

Display Screen

• Never push on the display screen’s LCD

panel or subject it to strong impact. Doing

so can cause the LCD panel’s glass to

crack, creating the risk of personal injury.

• Should the LCD panel ever crack or break,

never touch the liquid inside of the panel.

LCD panel liquid can cause skin irritation.

• Should LCD panel liquid ever get inside

your mouth, immediately wash out your

mouth with water and contact your

physician.

• Should LCD panel liquid ever get into

your eyes or onto your skin, rinse with

clear water for at least 15 minutes, and

then contact a physician.

Sound Volume

Do not listen to music at very loud volumes

for long periods. Particular care concerning

this precaution is required when using

headphones. High volume settings can

damage your hearing.

Heavy Objects

Never place heavy object on top of the

product.

Doing so can make the product top heavy,

causing the product to tip over or the object

to fall from it, creating the risk of personal

injury.

Correct Stand* Assembly

An incorrectly assembled stand can tip over,

causing the product to fall and creating the

risk of personal injury.

Make sure you assemble the stand correctly,

following the assembly instructions that

come with it. Make sure you mount the

product on the stand correctly.

* Stand is available as an option.

IMPORTANT!

When using batteries, be sure to replace them or shift to

one of the alternate power sources whenever you notice

any of the following symptoms.

• Dim power indicator

• Instrument does not turn on

• Display that is flickering, dim, or difficult to read

• Abnormally low speaker/headphone volume

• Distortion of sound output

• Occasional interruption of sound when playing at high

volumes

• Sudden power failure when playing at high volumes

• Flickering or dimming of the display when playing at high

volume

• Continued sound output even after you release a key

• A tone that is totally different from the one that is selected

• Abnormal rhythm pattern and demo tune play

• Loss of power, sound distortion, or low volume when

playing from a connected computer or MIDI device

• Sudden power failure while reading from or writing to

external storage media

WK3200_e_01-09.p65 05.3.15, 6:16 PM4

E-5

738A-E-007A

Congratulations upon your selection of this CASIO musical instrument. This keyboard provides you with the following features

and functions.

❐ 550 Tones Include Rich Advanced Tones

A total of 332 Advanced Tones are programmed with DSP tones to make them richer and more powerful. Advanced tones like

Stereo Piano and Tremolo Electric Piano enhance the Piano and Electric Piano tones to create a totally new sound.

❐ 50 Drawbar Organ Tones

In addition to the 550 standards tones, the keyboard also includes 50 realistic drawbar organ tones. Drawbar organ tones can be

controlled using nine digital drawbars. You can also select percussion or key click, and even edit the parameters of preset tone

and save up to 100 original tones in user tone memory.

❐ Flash Memory

Built-in Flash memory lets you expand your selection of tones and rhythms by downloading data from the CASIO MUSIC SITE,

or by the CD-ROM that comes bundled with the keyboard. You can also store up to 200 SMF format music files for playback.

❐ PIANO SETTING Button

The press of a button optimizes the keyboard setup for piano play.

❐ 160 Preset Rhythms + 16 User Rhythms

A selection of 160 rhythms includes accompaniments for everything from rock to pops and jazz.

You can also transfer accompaniment data from your computer and store up to 16 of them as user rhythms in keyboard memory.

❐ Auto Accompaniment

Simply play a chord and the corresponding rhythm, bass and chord parts play automatically. One-touch Preset instantly recalls

the most suitable tone and tempo settings to match the rhythm you are using.

❐ Big, Information-packed Display

A big built-in display shows chord names, tempo setting, keyboard information, staff notation of notes played, and more for full

support of all your keyboard play. A built-in backlight keeps the display easy to read, even in total darkness.

❐ Song Memory

Record up to six parts in memory, along with their tone, volume, pan position, and other parameters for later playback. Realistic

ensemble play can also be created using the Auto Accompaniment function.

❐ Synthesizer Mode

Edit built-in sounds to produce your own original creations. Up to 120 of your own sounds can be stored in memory for recall,

just like the built-in tones.

❐ General MIDI compatibility

The General MIDI tones of this keyboard let you connect to a personal computer to enjoy “desktop music” capabilities. This

keyboard can be used as a desktop music input device or sound source, and it's just the thing for playback of commercially

available pre-recorded General MIDI music software.

❐ Powerful effects

A collection of powerful effects, such as DSP reverb, chorus, and more, give you total control over the type of sound you want.

You can even change the parameters of an effect to create your own, original effects. A 4-band equalizer is also included.

Introduction

WK3200_e_01-09.p65 05.3.15, 6:16 PM5

E-6

❐ Mixer

You can specify tone, volume, pan position, and other parameters for each built-in Auto Accompaniment part. You can also

control the same parameters for each channel during MIDI input.

❐ Registration Memory

Keyboard setups can be stored in memory for later recall and instant settings whenever you need them. Up to 32 setups (4 setups

x 8 banks) can be stored in registration memory.

❐ Data download from your computer

You can use your computer to download data from the CASIO MUSIC SITE.

❐ SmartMedia

TM

Card Slot

A built-in SmartMedia card slot helps to simplify transfer of data from a computer and lets you store volumes of data for later

recall when you need it. You can also load a card with a standard MIDI file (SMF) and play it back on the keyboard.

❐ Built-in floppy disk drive (WK-3700 only)

Save original tones or songs you created with the Song Memory to disk for long-term storage. You can also load a disk with a

standard MIDI file (SMF) and play it back on the keyboard.

Introduction

738A-E-008A

WK3200_e_01-09.p65 05.3.15, 6:16 PM6

E-7

738A-E-009A

Contents

Safety Precautions ................E-1

Introduction ...........................E-5

General Guide...................... E-10

Attaching the Score Stand ..................... E-11

Playing a Demo Tune .............................E-12

Power Supply ......................E-14

Using batteries .......................................E-14

Using the AC Adaptor .............................E-15

Auto Power Off.......................................E-15

Turning Off the Keyboard .......................E-16

Memory Contents...................................E-16

Connections ........................E-17

Basic Operations.................E-19

To play the keyboard ..............................E-19

Selecting a Tone.....................................E-19

PIANO SETTING Button ........................E-20

Using the PITCH BEND Wheel ..............E-21

Using the MODULATION .......................E-21

Using the Drawbar Organ

Mode .....................................E-22

To select a drawbar organ tone..............E-24

To edit a drawbar organ tone ................. E-24

Parameter Details ..................................E-25

To save an edited drawbar organ tone...E-26

Applying Effects to Tones ....E-27

Effect Blocks ..........................................E-27

Selecting a DSP Type ............................E-28

About the DSP Button ............................E-29

Selecting REVERB ................................E-29

Selecting CHORUS................................E-30

Using the Equalizer ................................E-31

Auto Accompaniment .........E-32

About the MODE Button ........................E-32

Selecting a Rhythm ................................E-32

Playing a Rhythm ...................................E-33

Adjusting the Tempo...............................E-33

Using Auto Accompaniment ...................E-33

Using an Intro Pattern ............................E-36

Using a Fill-in Pattern .............................E-36

Using a Rhythm Variation.......................E-37

Synchro Starting Accompaniment

with Rhythm Play ...................................E-37

Finishing with an Ending Pattern ...........E-37

Using One-touch Preset.........................E-38

Using Auto Harmonize ...........................E-38

Adjusting the Accompaniment Volume...E-39

Mixer Function..................... E-40

What you can do with the Mixer .............E-40

Turning Channels On and Off ................E-40

Using the Parameter Edit Mode .............E-41

How Parameters Work ...........................E-42

WK3200_e_01-09.p65 05.3.15, 6:16 PM7

E-8

738A-E-010A

Contents

Synthesizer Mode................ E-44

Synthesizer Mode Functions..................E-44

Creating a User Tone .............................E-47

Storing a User Tone In Memory .............E-50

Registration Memory ..........E-51

Registration Memory Features...............E-51

To Save a Setup in Registration

Memory ..................................................E-52

To Recall a Setup from Registration

Memory ..................................................E-52

Song Memory Function ......E-53

Tracks ....................................................E-53

Basic Song Memory operations .............E-53

Using Real-time Recording ....................E-54

Mixer Mode Settings ..............................E-55

Playing Back from Song Memory...........E-56

Recording Melody and Chords with

Step Recording ......................................E-56

Recording Multiple Tracks......................E-59

Correcting Mistakes While Step

Recording...............................................E-60

Editing Memory Contents.......................E-62

Editing a Song........................................E-64

Keyboard Settings ..............E-65

Using Layer ............................................E-65

Using Split ..............................................E-66

Using Layer and Split Together ..............E-67

Transposing the Keyboard .....................E-68

Using Touch Response ..........................E-68

Tuning the Keyboard ..............................E-69

Changing Other Settings........................E-70

Using the SMF Player .........E-74

Playing Back an SMF .............................E-76

Configuring Other Settings.....................E-77

MIDI....................................... E-79

What is MIDI? ........................................E-79

General MIDI..........................................E-79

MIDI Settings .........................................E-79

Using the Music Data Management

Software (on the Bundled CD-ROM) .....E-80

WK3200_e_01-09.p65 05.3.15, 6:16 PM8

E-9

Contents

738A-E-011A

Company and product names used in this

manual may be registered trademarks of

others.

Saving Data.......................... E-82

Using a SmartMedia Card......................E-83

Using the Floppy Disk Drive

(WK-3700 Only) .....................................E-84

Using External Storage Media ...............E-86

Saving Files ...........................................E-87

Loading a File ........................................E-88

Renaming a File .....................................E-90

Deleting a File ........................................E-90

Formatting External Storage Media .......E-91

Inputting Characters...............................E-92

SmartMedia Card Error Messages ........E-93

Disk Drive Error Messages

(WK-3700 Only) .....................................E-94

Troubleshooting .................. E-95

Specifications ......................E-98

Care of your Instrument ...E-101

Appendix ............................... A-1

Tone List...................................................A-1

Drum Assignment List ..............................A-9

Rhythm List ............................................ A-11

Fingered Chord Chart ............................A-12

Effect List ...............................................A-14

DSP Algorithm List .................................A-16

MIDI Implementation Chart

WK3200_e_01-09.p65 05.3.15, 6:16 PM9

E-10

738A-E-012A

General Guide

8 C0

K L

A B

I

TSR U

1 2 73 654

9

FD G HE

M MQN O P

V W X

Y Z [ \ ]

a b

J

_

c

*

1

*

2

*

3

WK3200_e_10-21.p65 05.3.18, 2:31 PM10

E-11

General Guide

738A-E-013A

• Illustrations in this User’s Guide shows the WK-3700.

1 POWER button

2 Power indicator

3 MODE button

4 EFFECT button

5 SYNTH button

6 MIXER button

7 TRANSPOSE/FUNCTION button

8 MAIN VOLUME knob

9 ONE TOUCH PRESET button

0 ACCOMP VOLUME button

A SONG MEMORY button

B 쎲WK-3700

DISK/CARD button

쎲WK-3200

CARD button

C DATA ACCESS lamp

D RHYTHM button

E TONE button

F DSP button

G PIANO SETTING button

H

[왖]

/

[왔]

/

[왗]

/

[왘]

CURSOR buttons

I EXIT button

J AUTO HARMONIZE button

K SPLIT button

L LAYER button

M Speaker

N Rhythm list

O Tone list

P Display

Q DEMO button*

4

R 쎲WK-3700

PHONES terminal

쎲WK-3200

PHONES/OUTPUT terminal

S CHORD root names

T Percussion instrument list

U Chord types name

V SMF PLAYER button

W CHANNEL button(1~16, DSP)/drawbar buttons

X DRAWBAR ORGAN button

Y INTRO/ENDING 1/2 buttons

Z VARIATION/FILL-IN 1/2 buttons

[ SYNCHRO/FILL-IN NEXT button

\ START/STOP button

] TEMPO buttons

_ SONG MEMORY TRACK buttons

a) BANK button

b) REGISTRATION buttons

c) STORE button

Attaching the Score Stand*1

Insert the score stand into the slot at the top

of the keyboard as shown in the illustration.

WK3200_e_10-21.p65 05.3.15, 6:16 PM11

E-12

a

Number buttons

b

[+]/[–] buttons

(YES/NO)

• For input of numbers to

change displayed settings.

• Negative values can be

changed only by using [+]

and [–] to increment and

decrement the displayed

value.

Playing a Demo Tune*4

Pressing the DEMO button starts demo tune play. There are 3 demo tunes, which continuously play in sequence. To stop demo

tune play, press either the DEMO button or the START/STOP button.

NOTE

• Pressing the [+]/[–] buttons skips to the next demo tune.

• The PIANO SETTING button, Layer, and Split are disabled while a demo tune is playing.

*

2

General Guide

738A-E-014A

*

3

• WK-3700

c

PITCH BEND wheel

d

MODULATION wheel

• WK-3200

c

MODULATION button

d

MODULATION button lamp

e

PITCH BEND wheel

c d

e

Front Panel

• WK-3700 only

f

Access lamp

g

Eject button

g

f

WK3200_e_10-21.p65 05.3.15, 6:16 PM12

E-13

Rear Panel

• WK-3700

h

MIDI OUT terminal

i

MIDI IN terminal

j

SUSTAIN/ASSIGNABLE JACK terminal

k

LINE OUT R, LINE OUT L/MONO terminal

l

DC 12V terminal

OUT IN

SUSTAIN/

ASSIGNABLE JACK

MIDI

DC 12V

h

i

j

k

OUT IN

SUSTAIN/

ASSIGNABLE JACK

MIDI

LINE OUT

R L/MONO

DC 12V

h

i

j k

l

• WK-3200

h

MIDI OUT terminal

i

MIDI IN terminal

j

SUSTAIN/ASSIGNABLE JACK terminal

k

DC 12V terminal

m

Rear Panel

General Guide

738A-E-015A

m

Card slot

NOTE

• Display examples shown in this User’s Guide are intended for illustrative purposes only. The actual text and values that

appear on the display may differ from the examples shown in this User’s Guide.

• Due to LCD element characteristics, display contrast changes depending on the angle from which you view it. The initial

default contrast setting is one that allows easy viewing for a musician seated directly in front of the display. You can also

adjust the contrast to the level that suits your particular needs. For more information, see page E-73.

WK3200_e_10-21.p65 05.3.15, 6:16 PM13

E-14

This keyboard can be powered by current from a standard

household wall outlet (using the specified AC adaptor) or by

batteries. Always make sure you turn the keyboard off

whenever you are not using it.

Using batteries

Always make sure you turn off the keyboard before loading

or replacing batteries.

To load batteries

1

Remove the battery compartment cover.

2

Load six D-size batteries into the battery

compartment.

• Make sure that the positive (+) and negative (–) ends

are facing correctly.

3

Insert the tabs on the battery compartment cover

into the holes provided and close the cover.

NOTE

• The keyboard may not function correctly if you load or

replace batteries with power turned on. If this happens,

turning the keyboard off and then back on again should

return functions back to normal.

Power Supply

tab

Important Battery Information

■

The following shows the approximate battery life.

Alkaline batteries ............................. 4 hours

The above value is standard battery life at normal

temperature, with the keyboard volume at a medium

setting. Temperature extremes or playing at very loud

volume settings can shorten battery life.

WARNING

Misuse of batteries can cause them to leak, resulting in

damage to nearby objects, or to explode, creating the risk of

fire and personal injury. Always make sure you observe the

following precautions.

• Never try to take batteries apart or allow them to

become shorted.

• Never expose batteries to heat or dispose of them by

incineration.

• Never mix old batteries with new ones.

• Never mix batteries of different types.

• Do not charge the batteries.

• Make sure the positive (+) and negative (–) ends of

the batteries are facing correctly.

CAUTION

Misuse of batteries can cause them to leak resulting in

damage to nearby objects, or to explode, creating the risk of

fire and personal injury. Always make sure you observe the

following precautions.

• Use only batteries that are specified for use with this

product.

• Remove batteries from the product if you do not plan

to use it for a long time.

738A-E-016A

WK3200_e_10-21.p65 05.3.15, 6:16 PM14

E-15

Using the AC Adaptor

Make sure that you use only the AC adaptor specified for

this keyboard.

Specified AC Adaptor: AD-12

Note the following important precautions to avoid damage

to the power cord.

● During Use

• Never pull on the cord with excessive force.

• Never repeatedly pull on the cord.

• Never twist the cord at the base of the plug or connector.

• The power cord should not be stretched tight while it is in

use.

● During Movement

• Before moving the keyboard, be sure to unplug the AC

adaptor from the power outlet.

● During Storage

• Loop and bundle the power cord, but never wind it around

the AC adaptor.

IMPORTANT!

• Make sure that the keyboard is turned off before

connecting or disconnecting the AC adaptor.

• Using the AC adaptor for a long time can cause it to

become warm to the touch. This is normal and does not

indicate malfunction.

Power Supply

Auto Power Off

When you are using battery power, keyboard power turns

off automatically whenever you leave it on without

performing any operation for about 6 minutes. When this

happens, press the POWER button to turn power back on.

NOTE

• Auto Power Off is disabled (it does not function) when

you are using the AC adaptor to power the keyboard.

To disable Auto Power Off

Hold down the TONE button while turning on the keyboard

to disable Auto Power Off.

• When Auto Power Off is disabled, the keyboard does not

turn off automatically no matter how long it is left with no

operation being performed.

• Auto Power Off is automatically enabled whenever you

turn on keyboard power.

Settings

Tone, rhythm, and other “main keyboard settings” in effect

when you turn off the keyboard manually by pressing

POWER button or when Auto Power Off turns off power are

still in effect the next time you turn power back on.

Main Keyboard Settings

Tone number, layer, split, split point, drawbar organ

tone settings, transpose, tuning, and contrast settings,

touch response, reverb, chorus, DSP, equalizer, rhythm

number, tempo, keyboard channel, MIDI In Chord

Judge on/off, accomp MIDI out on/off, assignable

jack setting, accompaniment volume, user area tones

(Synthesizer Mode), user area accompaniments, user

DSP area, pitch bend range, Auto Harmonize on/off,

Auto Harmonize type, Mixer hold, DSP hold, Auto

Accompaniment mode, all Mixer parameters, all

Synthesizer Mode parameters, Song Memory song

numbers, SMF player settings (play mode, manual

play part, SMF playback volume)

738A-E-017A

AC adaptor AD-12

AC outlet

OUT IN

SUSTAIN/

ASSIGNABLE JACK

MIDI

LINE OUT

R L/MONO

DC 12V

WK3200_e_10-21.p65 05.3.15, 6:16 PM15

E-16

Power Supply

Turning Off the Keyboard

• Be sure to press the POWER button to turn off power and

make sure that the LCD backlight is off before disconnecting

the AC adaptor or doing anything else.

• Never disconnect the AC adaptor while the keyboard is

turned on or try to turn off power using any other technique

besides pressing the POWER button. Doing so can cause

the contents of the keyboard’s Flash memory to become

corrupted. Strange keyboard operation and abnormal

startup when power is turned on are symptoms of

corrupted Flash memory contents. See “Troubleshooting”

on page E-95 for more information.

IMPORTANT!

• While the following message is on the display, never

turn off the keyboard by pressing the POWER button,

disconnecting the AC adaptor, etc.

(message) “Pls Wait” or “Bulk In”

Turning off the keyboard while the above message is

on the display can cause user data (user tones, song

memory data, etc.) currently stored in keyboard memory

or on external media to become corrupted. Once

corrupted, you may not be able to recall the data again.

Memory Contents

In addition to the above settings, data stored in the

Registration Mode and Song Memory Mode is also retained

when keyboard power is turned off.

Saving Setups and Memory Contents

About Flash memory

Your keyboard comes with built-in Flash memory, which can

continue to hold data even when electrical power is totally

cut off. This means that even after batteries go completely

dead, you can attach the AC adaptor, turn on power, and still

recall data stored in memory.

You can back up keyboard memory contents and other data

using the media described below.

• SmartMedia

TM

Card

See “Using a SmartMedia Card” on page E-83.

• Floppy Diskette (WK-3700 only)

See “Using the Floppy Disk Drive (WK-3700 Only)” on page

E-84.

• Computer hard disk

See “MIDI” on page E-79.

738A-E-018A

IMPORTANT!

• When running under battery power, be sure to replace

batteries as soon as possible after the first signs of low

battery power (dim power indicator lamp, dim display

characters, etc.) Though the keyboard’s Flash memory

is non-volatile (which means that data is not lost when

power is interrupted), data can be lost if power suddenly

fails while data is being written to flash memory*.

* While storing or deleting user data, while recording

with the synthesizer, while transferring data from a

computer, etc.

Initializing the Keyboard

Initialization can be used to return keyboard parameters to

their initial factory default settings, or to delete all data

currently in keyboard memory. See page E-73 for more

information about initialization.

Returning the keyboard to its initial factory defaults

You can use the CD-ROM that comes with the keyboard and

your computer to return the keyboard’s flash memory and

all of its parameters to their initial factory default settings.

See “Bundled CD-ROM Data” on page E-80 for details.

WK3200_e_10-21.p65 05.3.15, 6:16 PM16

E-17

Connections

• WK-3700

Phones and Line Out Terminals

Before connecting phones or other external equipment, be

sure to first turn down the volume settings of the keyboard

and the connected equipment. You can then adjust volume

to the desired level after connections are complete.

[Front]

Connecting Phones

1

Connecting phones cuts off output from the keyboard’s built-

in speakers, so you can play even late at night without

disturbing anyone.

[Rear Panel]

Connecting to Audio Equipment

2

Use commercially available cords to connect to the two jacks

as shown in Figure

2

. It is up to you to purchase connecting

cables like the ones shown in the illustration for connection.

Normally in this configuration, you must set the audio

equipment’s input selector to the setting that specifies the

terminal (such as AUX IN) that the keyboard is connected to.

Use the keyboard’s MAIN VOLUME knob to adjust the

volume level.

OUT IN

SUSTAIN/

ASSIGNABLE JACK

MIDI

LINE OUT

R L/MONO

DC 12V

Standard plugs

Guitar amplifier,

keyboard amplifier, etc.

Audio amplifier AUX IN, etc.

PIN plug

Standard jacks

INPUT 1

INPUT 2

LEFT

(White)

RIGHT

(Red)

Connecting to a Musical Instrument Amplifier

3

Use commercially available cords to connect to the two jacks

as shown in Figure

3

. It is up to you to purchase connecting

cables like the ones shown in the illustration for connection.

Use the keyboard’s MAIN VOLUME knob to adjust the

volume level.

• If your amplifier has only one input jack, connect a cord to

the L/MONO jack only.

NOTE

• You can also connect the keyboard’s MIDI terminal to a

computer or sequencer. See “MIDI” on page E-79 for

details.

738A-E-019A

1

PHONES Terminal

Stereo standard plug

• WK-3200

Phones/Output Terminal

Before connecting phones or other external equipment, be

sure to first turn down the volume settings of the keyboard

and the connected equipment. You can then adjust volume

to the desired level after connections are complete.

[Front]

Connecting Phones

1

Connecting phones cuts off output from the keyboard’s built-

in speakers, so you can play even late at night without

disturbing anyone.

Audio Equipment

2

Connect the keyboard to a audio equipment using a

commercially available connecting cord with a standard plug

on one end and two PIN plugs on the other end. Note that

the standard plug you connect to the keyboard must be a

stereo plug, otherwise you will be able to output only one of

stereo channels. In this configuration, you normally set the

input selector of the audio equipment to the terminal (usually

marked AUX IN or something similar) where the cord from

the keyboard is connected. See the user documentation that

comes with your audio equipment for full details.

LEFT

RIGHT

AUX IN or similar terminal

of audio amplifier

White

Red

PIN plug

Stereo standard

plug

Audio connection

PHONES/OUTPUT Terminal

Keyboard amp,

guitar amp, etc.

1

2

3

WK3200_e_10-21.p65 05.3.15, 6:16 PM17

E-18

Connections

Musical Instrument Amplifier

3

Use a commercially available connecting cord to connect the

keyboard to a musical instrument amplifier.

NOTE

• Be sure to use a connecting cord that has a stereo

standard plug on the end you connect to the keyboard,

and a connector that provides dual channel (left and

right) input to the amplifier to which you are connecting.

The wrong type of connector at either end can cause

one of the stereo channels to be lost.

• When connected to a musical instrument amplifier, set the

volume of the keyboard to a relatively low level and make

output volume adjustments using the amplifier’s controls.

Connection Example

NOTE

• You can also connect the keyboard to a computer or

sequencer. See “MIDI” on page E-79 for details.

Sustain/Assignable jack Terminal

You can connect an optional sustain pedal (SP-3 or SP-20) to

the SUSTAIN/ASSIGNABLE JACK terminal to enable the

capabilities described below.

For details on how to select the pedal function you want, see

“Changing Other Settings” on page E-70.

Sustain Pedal

• With piano tones, depressing the pedal causes notes to

linger, much like a piano’s damper pedal.

• With organ tones, depressing the pedal causes notes to

continue to sound until the pedal is released.

INPUT 1

INPUT 2

PIN jack

PIN plug (red)

PIN plug (white)

Stereo standard plug

Keyboard or

guitar amp

To keyboard’s

PHONES/OUTPUT

terminal

Standard plug

738A-E-020A

OUT IN

SUSTAIN/

ASSIGNABLE JACK

MIDI

LINE OUT

R L/MONO

DC 12V

SP-20

SUSTAIN/ASSIGNABLE JACK Terminal

Sostenuto Pedal

• As with the sustain pedal function described above,

depressing the sostenuto pedal causes notes to be sustained.

• This difference between a sostenuto and sustain pedal is

the timing. With a sostenuto pedal, you press the keys and

then depress the pedal before you release the keys. Only

the notes that are sounding when the pedal is depressed

are sustained.

Soft Pedal

Depressing the pedal softens the sound of the notes being

played.

Rhythm Start/Stop Pedal

In this case, the pedal performs the same functions as the

START/STOP button.

Accessories and Options

Use only the accessories and options specified for this

keyboard. Use of non-authorized items creates the danger of

fire, electrical shock, and personal injury.

WK3200_e_10-21.p65 05.3.15, 6:16 PM18

Page is loading ...

Casio CTK-581 User manual

Casio CTK-581 User manual

Related papers

Other documents