2. Computers & electronics
  3. Networking
  4. Buffalo Technology
  5. WLI-TX4-G54HP
WLI-TX4-G54HP

Buffalo Technology WLI-TX4-G54HP User manual

  • Hello! I am an AI chatbot trained to assist you with the Buffalo Technology WLI-TX4-G54HP User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
User Manual
High Power Wireless
Ethernet Converter
WLI-TX4-G54HP
www.buffalotech.com
v1.6
2
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
AOSS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Manual Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Ethernet Converter Manager . . . . . . . . . . . . . . . . . . . . . . . . 7
CongurationwithoutSoftware...........................11
Web-based Conguration . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Advanced Conguration . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
W i r e l e s s S e t t i n g s . . . . . . . . . . . . . . . . . . 1 8
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tro ub leshoot in g . . . . . . . . . . . . . . . . . . . . . . . . 24
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3
Congratulationsonyourpurchase!YournewHighPowerWirelessEthernetConverter
allowsyoutoconnectanydevicewithan Ethernet porttoawirelessnetwork.AOSS
makesforeffortlesssetupandourTurboGHighPowertechnologygivessuperbrange
and speed.
Contents
• Wireless Ethernet Converter
• Ethernet Converter Utility CD-ROM
• 7ft. Ethernet Cable
• AC Adapter
•QuickSetupGuide
• Warranty Statement
Ifanyitemsaremissing,pleasecontacttheresellerfromwhomyoupurchasedthis
product.
System Requirements
•DesktoporNotebookcomputerwithanRJ-45Ethernetport(forconguration)
•WebBrowser(Firefox1.0orlater,Mozilla5.0orlater,orIE5.0orlater)
•802.11bor802.11gaccesspoint(InfrastructureMode)ORadifferentcomputerwith
and802.11bor802.11gwirelessadapter(Ad-hocMode)
4
Getting Started
PlugtheA/CadapterintoanA/Cpowersourceandplugthe
connectorintothebackoftheEthernetConverter.Itwilltake
about30secondstobootup.
ScrewtheantennaintothetoporsideofyourWirelessEthernet
Converterasshown.Youmayalsoattachtheoptionalstand
ifyouwish.Forbestperformance,orienttheantennato
pointstraightup.Ifyouwanttosubstituteadifferent2.4GHz
antenna,makesurethatithasthecorrectRP-SMAconnector.
5
IfyourWirelessRouter/AccessPointsupportsAOSS,thenAOSScancongureyourwireless
networkforyou.TocongureyournetworkwithAOSS:
•ConrmthattheWirelessRouter/AccessPointandtheEthernetConverterarebothpoweredup.
•HoldintheAOSSbuttonontheWirelessRouter/AccessPointfor3seconds.
•HoldintheAOSSbuttonontheEthernetConverterfor3seconds.
AOSSwilltakeaboutaminutetocongureyourwirelessnetwork.Whennished,theAOSSLEDs
onboththeWirelessRouter/AccessPointandtheEthernetConverterwillstopblinkingandstaylit.
Younowhaveasecureconnection!
NOTES:
IfAOSSisused,thenanynon-AOSSwirelessclientdevicesinyournetworkwillhavetobe
manuallyre-conguredtoconnecttotheRouter/AccessPointinAOSSmode;pleaseconsultyour
Router/AccessPointdocumentationformoreinformationonaddingnon-AOSSdevices.
AOSSconguresyourSSID,encryptiontype,wireless
channel,andencryptionkey,andmakesasecure
connectionbetweenyourwirelesscomponents.Youmay
stillneedtorunyourrouter'scongurationutilityto
congureyourinternetconnection.
IfAOSSdoesnotnishproperly,powercycleboththe
Router/AccessPointandtheEthernetConverterand
attempttheAOSSprocessagain.AOSSworksbestwhen
therouterandtheEthernetConverterarephysicallyclose.Youcanalwaysmovethem
furtherapartwhencongurationiscomplete.
AOSS Installation
AOSS button
6
Ifyourwirelessrouter/accesspointdoesn'tsupportAOSS,you'llneedtocongure
theaccesspointmanually.Therearetwowaystodothis:youcanusetheEthernet
ConverterManagersoftwareifyouhaveaWindowsPConthenetwork(98/ME/2000/XP
only),oryoumayuseawebbrowser.Webbrowsercongurationmaybedonewithany
computerrunningarecentwebbrowser,includingMacintoshandLinuxmachines.Skip
to page 11forwebbasedconguration.
Manual Configuration
7
IfyouhaveaWindows98/ME/2000/XPmachinewithaCD-ROMdriveavailableonyour
computernetwork,theEthernetConverterManagermakesitsimpletocongurethe
EthernetConverter.ThefollowingstepswillguideyouthroughconguringtheEthernet
Converter via the Ethernet Converter Manager.
ConnectoneoftheEthernetConverter'sLANportstoanopenportonyournetwork's
router,switchorhubwiththeincludednetworkpatchcable.Iftherearenoports
available, you can temporarily remove a computer or other connected device and plug
the Ethernet Converter to that port. You can plug the Ethernet Converter directly to the
conguringcomputer,butwillhavetoconguresettingsmanuallyasdescribedonpage
17.
Oncethenetworkcablehasbeenpluggedin,plugtheEthernetConverter'sACAdapter
intoanavailablepoweroutlet.Thenattachthepowerconnectortothebackofthe
EthernetConverter.Thebootupprocesstakes30secondsandiscompletewhenboth
theWirelessandEthernetLEDsarelit.
ReturntothePCdesignatedforcongurationandinserttheincludedEthernetConverter
CD-ROMintothePC'sCD-ROMdrive.
TheEthernetConverterUtilityshouldlaunchautomatically.Ifitdoesnot,browseyour
CD-ROMdriveinWindowsandrunthesetup.exe program.
Configuration with Ethernet Converter Manager
8
ClickonEthernet Converter Manager.
TheEthernetConverterManagersoftwarewill
run. If the search doesn't begin automatically,
select the Search for an Ethernet Converter option
from the Editdropdownmenu.
9
TheEthernetConverterManagerwillsearchforall
BuffaloEthernetConvertersonyournetwork.The
processusuallytakeslessthanoneminute.Once
completed, the Search Resultswindowwillappear.
Search ResultswilllistallBuffaloEthernetConverters
onthenetwork.IfthereismorethanoneEthernet
Converterinthelist,selecttheoneyouwouldliketo
congure.PresstheIP Settings button to continue
conguration.
The IP Address Setupwindowwillopen.Checkthe
boxnexttoUse DHCP and press the OK button. The
EthernetConverterwillreboot;thisprocessmaytake
as long as a minute. The Ethernet Converter Manager
willthenre-scanthenetworkforEthernetConverters.
NOTE: IfyouwanttogiveyourEthernetConverter
astaticIPaddress,thanyoucanskipcheckingUse
DHCPandenteryourownIPAddressandSubnet
maskinthecoorespondingelds.IfusingastaticIP
address,itisrecommendedtopickoneinsideyour
existingnetwork'ssubnet.
10
Search Resultswillappearagain.Ifmorethanone
Ethernet Converter is present, select the proper
Ethernet Converter from the list. Then press the
Congure button.
TheEthernetConverterManagerwillconnect
youtotheEthernetConverter'swebbased
congurationtool.Youwillbepromptedfora
usernameandpassword.
By default, the username is root and there is no
password.
After entering the user name, press the OK button.
Pleaseskiptopage 13tocontinueconguration.
11
YoumayalsoentertheWeb-basedCongurationToolwithoutusingthesoftware.This
maybenecessarytoconguretheconverterwithouttheuseofaWindowsPC.Usethis
methodwithLinux,Macintosh,otherothernon-WindowsPCstoaccesstheWeb-based
CongurationTool.
RefertoyouroperatingsystemdocumentationonhowtocongureaStaticIPaddress.
TheEthernetConverterhasanIPaddressof1.1.1.1bydefault.You'llneedtocongure
thecomputertobeonthesamesubnet;anIPaddressof1.1.1.2isrecommendedforthe
computer.
Withtheincludednetworkpatchcable,connectoneoftheEthernetConverter'sLAN
portstoanopenEthernetportonarouter,switch,orhubonyournetwork.Alternately,
youcanplugtheEthernetConverterdirectlytotheconguringcomputer'sEthernetport.
Oncethenetworkcablehasbeenpluggedin,plugtheEthernetConverter'sACAdapter
intoanavailablepoweroutlet.Thenattachthepowerconnectortothebackofthe
EthernetConverter.Thebootprocesstakeslessthanaminuteandiscompletedwhen
both the Wireless and Ethernet lights are lit.
Configuration without PC Software
12
OnceyourcomputerhasaStaticIPaddressof1.1.1.2,
openyourwebbrowserandenter1.1.1.1 by typing it
intotheAddresseldandthenpressingEnter on your
keyboard.
Youwillbepromptedforausernameandpassword.
By default, the username is root and there is no
password.
After entering the user name, press the OK button.
13
TheWebBasedCongurationToolletsyou
changetheEthernetConverter'sconguration.
ThroughWebBasedConguration,youcan
changethewirelessnetworktheEthernet
Converterisassociatedwith,theIPaddressofthe
Ethernet Converter, and other important settings.
Afterlogginginonthepreviouspages,youwill
begreetedbythemaincongurationpage.
Thispagequicklyshowsyouwhatnetworkthe
EthernetConverterisconnectedtoaswellas
allowingyoutosearchforavailablenetworks.
TherststepinWebBasedCongurationshould
betosearchforanavailablewirelessnetwork.
To do this, press the Search button in the SSID
(Network Name) table.
After pressing the Search button, the Search for
SSIDprogramwillndanynetworksinyourarea
that are broadcasting their SSIDs. Select the
wirelessnetworkthatyouwouldliketoconnectto
and press the Select button.
Web-Based Configuration Tool
14
Afterselectingawirelessnetwork,youwillbereturnedtothemainWebBased
Congurationpage.
IfthewirelessnetworkyouareattemptingtoconnecttoisnotbroadcastingitsSSID,
thenyouwillberequiredtomanuallyentertheSSIDintotheSSIDeld.Aftertheeldis
populatedwiththeproperSSID,presstheApply Settings button.
Ifencryptionisenabledonthewirelessnetworkyou'veselected,youwillneedtoenterthe
encryptionkey(see
page 15).
15
ClickRefresh to see the current status of your
wirelessconnection.SSID (Network Name)willbe
populatednow(seepages 13-14ifitisn't).
Belowit,
Wireless Network Type may be set to
Infrastructure if you're connecting the Wireless
Ethernet Converter to a router or access point, or Ad
hocifyou'reconnectingittoanotherwirelessclient.
Encryption Mode should be set to use the same type
ofencryptionastheotherwirelessdevicesonyour
network.TheEthernetConvertersupportsWEP128,
WEP64,TKIP,andAESencryption.AESishighly
recommendedifallyourotherwirelessdevices
support it.
Totherightoftheencryptiondropboxistheeldwhereyouenteryour
encryption key.
SSID, Encryption Mode, and Encryption Keymustbesetexactlythesameinallofyour
wirelessdevices,ortheywillnotbeabletocommunicatewitheachother.
Checkyourrouter/accesspoint'sdocumentationifyoudon'tknowwhattheSSID,
EncryptionMode,andEncryptionkeyareonyournetwork.
16
Onceyou'veconguredthesebasicsettings(especiallySSID, the Encryption Mode, and
the Encryption Key),theEthernetConvertershouldbeabletoconnecttoyourother
wirelessdevices.Tocontinueconguringadvancedsettings,pleaseskiptothenextpage.
DisconnecttheEthernetConverterfromthewirednetworkconnectionandmoveittoits
desired location.
YoumayconnectfourwiredEthernetdevicestotheEthernetConverter'sLANports.
ConnecteddevicesmayincludeXBoxes,PS2s,HomeTheaterequipment,switches,
hubs,oranothercomputersystem.PlugtheACAdapterintoanearbypoweroutletand
connectittotheEthernetConverter.Powercycleanydevicesthatareconnectedtothe
Ethernet Converter.
IfyousetastaticIPaddressonyourcomputeron
page 11, then restore the computer's
IPsettingsto
obtain an IP Address automatically.
Congratulations!YourEthernetConverterissetup.Ifyouneedtocongureyour
Ethernet Converter further, use the Ethernet Converter Search Utility and press the
Congure button (page 8).TurntothenextpageforAdvanced Settings.
17
Mostuserswillneverneedtochangeanysettingsfortheir
Wireless Ethernet Converter besides the basic ones in the
maincongurationwindow,coveredonpages 13-15. If
you'reoneoftheexceptions,youmayaccessAdvanced
Settings by pressing the blue Advanced button in the bottom
rightcornerofthecongurationpage.
This is the Advanced Settings page. On the left, you
maychoosefromWirelessSettings,NetworkSettings,or
Management.Whenthepagerstopens,it'satWireless
Settings. Changes on the Advanced Settings page are not
applied until the Set button is pressed.
Advanced Settings
18
MAC Address - By default, the Ethernet Converter transmits
itsownMACaddress,butyoumaychangethissothatit
transmitstheMACaddressoftherstdevicepluggedintoit
totransmitadatapacket.
SSID-IntheSSIDeld,entertheSSIDnameofthewireless
networkthattheEthernetConverteristoconnectwith.Use
thesameSSIDasyourrouter/accesspoint.Youmaynd
available broadcasting SSIDs by pressing the Search button.
Wireless Network Type-ChoosebetweenInfrastructure
(AccessPointBased)orAd-hoc(ClienttoClient).
Wireless Channel-ThechannelwillbeautomaticallyselectedinInfrastructurenetworks.
ForAd-hocnetworks,bothclientsmustbesettothesamechannel.
Wireless Mode-ThewirelessmodeonlyappliestoAd-hocconnections.IftheEthernet
ConverterismakinganAd-hocconnectionwithan802.11bclient,thenselect802.11b
fromthedropdownmenu.Ifan802.11gclientisconnectingtotheEthernetConverter
then select the Auto-802.11g-802.11b option.
BSS Basic Rate Set - The basic rate set only applies to Ad-hoc connections. Select the
properratesetfortheAd-hocclienttheEthernetConverterisgoingtoassociatewith.
Older routers may require that you reduce the BSS Basic Rate set to Default(11b). If you
are unsure of the correct setting, try Default.
Wireless Settings
19
Frame Bursting Mode-FrameBurstingtechnologyallowsforquickerwirelessnetwork
speedsbyreducingtheoverheadforeachwirelesspacket.Ifyouraccesspointsupports
it, 125* High-Speed Mode offers the best overall performance of the frame bursting modes.
You may leave this set to the 125* High Speed Modeatalltimes;ifacompatableaccess
pointisnotavailablethenthedevicewilloperateasastandard802.11gdevice.
Wireless Output Power-Thewirelessoutputpowersettingchangesthepowerof
theEthernetConverter'sinternalradio.Reducingtheoutputpowercanoftenreduce
interferencewithotherdevices.Youshouldleavetheoutputpowersetat100%unless
youwanttoreducerangeorinterferencewithother2.4GHzdevicesisapparent.
Data Encryption-SelectWEP64,WEP128,TKIP,orAESencryptionfromthedropbox.If
WEPisselected,thenaWEPkeyorseriesofWEPkeysmustbeenteredintotheWEPkey
eld(s).PleaseselectwhetherthespecickeyisASCIIorHEXfromthepulldownlistnext
tothekeyelds.IfTKIPorAESisused,thenenterthepre-sharedkeyintheWPA-PSK
eld.
Wireless Settings
20
Automatic Assignment (DHCP Server) - This setting
allowstheEthernetConvertertoobtainitsIPaddress
automaticallyfromaDHCPserveronthenetwork.
Manual Assignment - This assigns the Ethernet
Converteraspecic("Static")IPaddress.IfaStaticIP
addressisselected,youmustenteraSubnetMaskas
well.
NOTES: ToconguretheEthernetConverterinthefuture,ausermustbothknowitsIP
address,and,beonthesamesubnet.BecarefulwhenchangingtheEthernetConverter’s
IPaddress!
IfchangestotheEthernetConverter’sIPaddressmakeitdifcultforyoutoaccessthe
web-basedcongurationutility,rememberthatyoucanusetheEthernetConverter
ManagementsoftwaretorecongureorresetDHCP(seepages8-9)oraStaticIP
address.IftheEthernetConverter'sIPaddresshasrevertedtothedefault1.1.1.1,you
maymanuallycongureyourcomputertoanIPaddressonthesamesubnet,suchas
1.1.1.2,allowingittoconnecttotheEthernetConverter(seepages11-12).Don'tforget
tochangeyourcomputer'sIPaddressbackwhenyou'venishedconguringtheEthernet
Converter.
TheIPAddressdoesnotneedtobeintherangeoftheDHCPserver'sscopeto
successfullypassDHCPrequeststonetworkclientsbehindtheEthernetConverter.
Network Settings
/