Smooth Fitness 2 User manual

USER’S MANUAL

6.17 MOTORIZED TREADMILL

USER WEIGHT LIMITATION: 350LBS (150KGS)

SERIAL NUMBER (Found on Frame):

6.17 MOTORIZD TREADMILL

2



WWW.SMOOTHFITNESS.COM

PRECAUTIONS

For Future Service or Related Questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your

treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

WARNING:

To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and

information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are

adequately informed of all warnings and precautions.

• Use the treadmill only as described in this manual.

• Place on a level surface, with 6 feet (2 m) of clearance behind it. Do not place the treadmill on any surface that

blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.

• When choosing a location for the treadmill makes sure that the location and position permit access to a plug.

• Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio,

or near water.

• Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the treadmill at all times.

• The treadmill should not be used by persons weighing more than 350 LBS (150 kgs)

• Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using

the treadmill. Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are

recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet,

wearing only stockings, or in sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be

on the same circuit.

• Always straddle the belt and allow it to start moving before stepping onto the belt.

• Always examine your treadmill before using to ensure all parts are in working order.

• Allow the belt to fully stop before dismounting.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your treadmill.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill.

Do not operate the treadmill with a damaged or frayed power cord.

• Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be

performed by an authorized service representative, unless authorized and/or instructed by the manufacturer.

Failure to follow these instructions will void the treadmill warranty.

• Never leave the treadmill unattended while it is running.

• The equipment is for Class B (Home Use).

3

6.17MOTORIZDTREADMILL



POWER REQUIREMENT

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN

ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS

TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE

PRODUCT, IF IT WILL NOT FIT THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED

ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes,

surges and noise interference can result from weather conditions or from other appliances being turned on or off. To

reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance

for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an

equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug

the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local

codes and ordinances.

This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like the plug illustrated in the

drawing below.

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

4



PREASSEMBLY

Open The Boxes:

You are now ready to open the boxes of your new equipment.

Make sure to inventory all of the parts that are included in the boxes.

Check the Hardware Comparison Chart for a full count of the number of parts included for this product to be assembled

properly. If you are missing any parts or have any assembly questions call your local Smooth Retailer.

Gather Your Tools:

Before starting the assembly of your unit, make sure that you have gathered all the necessary tools you may require to

assemble the unit properly. Having all of the necessary equipment at hand will save time and make the assembly quick and

hassle-free.

Clear Your Work Area:

Make sure that you have cleared away a large enough space to properly assemble the unit.

Make sure the space is free from anything that may cause injury during assembly.

After the unit is fully assembled, make sure there is a comfortable amount of free area around the unit for unobstructed

operation.

Invite a Friend:

Some of the assembly steps may require heavy lifting.

It is recommended that you obtain the assistance of another person when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product.

If you weigh more than 350LB (Approx. 150 Kg). It is not recommended that you use this product.

Serious injury may occur if the user’s weight exceeds the limit shown here. This product is not intended to

support users whose weight exceeds this limit.

Care and Maintenance :

1. The safety level can be maintained only if it is examined for damage and wear.

2. Replace the defect components immediately and do not use the equipment until it is repaired.

3. Always mount the equipment and straddle the running belt before you start the treadmill. Dismount from the

treadmill only after the running belt has stopped.

4. Always check for worn components like pulleys, belts etc.

5. Emergency Stop: You can stop the treadmill immediately by removing the safety key.

WWW.SMOOTHFITNESS.COM

5

6.17MOTORIZDTREADMILL



HARDWARE COMPARISON CHART

Hardware Chart:

For your convenience, we have identified the hardware used in the assembly of this product.

This chart is provided to help you identify those items that may be unfamiliar to you.

No. Description Qty.

310 Screw Cover 2

802 Φ8 Washer 10

804 M8x45mm Allen Head Cap Bolt 4

805 M8x51mm Allen Head Cap Bolt 2

806 Φ4x14mm Screw 4

830 M8x18mm Allen Head Cap Bolt 4

304 Hand bar Cover - LL 1

305 Hand bar Cover - LR 1

307 Hand bar Cover - RL 1

308 Hand bar Cover - RR 1

604 Upright Base Cover-L-Back 1

607 Upright Base Cover-R-Back 1

104 Safety Key 1

A 6mm Allen key 1

B 6mm Allen key 1

C Screw Driver 1

D Oil Can 1

E Power Cord 1

F 5mm Allen Wrench 1

WWW.SMOOTHFITNESS.COM

1 x

BA

C

5mm 6mm

1 x 1 x

1 x

D

8mm

10 x

2 x

M8x51mm

M8x45mm

4 x

M8x18mm

4 x

4 x14mm

F

5mm

1 x

E

104

1 x

MILLIMETERS

6.17 MOTORIZD TREADMILL

6



PARTS LIST

Part No. Description Qty. Order No.

100

101 Computer Button Cover 1 6.17- 101

102 Console Housing -Upper 1 6.17- 102

103 Computer 1 6.17- 103

104 Safety Key 1 6.17- 104

105 Safety Key Base 1 6.17- 105

106 Button Board 1 6.17- 106

107 Console Housing-Bottom 1 6.17- 107

108 Overlay 1 6.17- 108

200

201 Console Fixed Tube -Left 1 6.17- 201

202 Handbar Foam -Small 2 6.17- 202

203 Console Fixed Tube -Right 1 6.17- 203

206 Handpulse Sensor -Upper 2 6.17- 206

207 Handpulse Sensor -Bottom 2 6.17- 207

208 Handbar Foam -Big 2 6.17- 208

209 Handpulse Tube 1 6.17- 209

300

301 Upright- Left 1 6.17- 301

302 7 Pin Computer Wire 1 6.17- 302

303 2 Pin Safety Key Wire 1 6.17- 303

304 Handbar Cover -LL 1 6.17- 304

305 Handbar Cover -LR 1 6.17- 305

306 Upright Connect Frame-Left 1 6.17- 306

307 Handbar Cover -RL 1 6.17- 307

308 Handbar Cover -RR 1 6.17- 308

309 Upright Connect Frame-Right 1 6.17- 309

310 Screw Cover 2 6.17- 310

311 Upright-Right 1 6.17- 311

400

401 Main Frame 1 6.17- 401

402 Front Roller 1 6.17- 402

403 Front Roller Shaft 1 6.17- 403

404 Elevation Control Board 1 6.17- 404

405 Rear Roller 1 6.17- 405

406 Control Board 1 6.17- 406

407 Rear Roller-Shaft 1 6.17- 407

408 Elevation Motor 1 6.17- 408

409 Elevation Motor Gear Sleeve 1 6.17- 409

410 Running Deck Cross Brace 1 6.17- 410

411 Running Deck Cross Brace Foam 1 6.17- 411

412 Wheel Cushion 2 6.17- 412

413 Elevation Control Board Fixing Insert 6 6.17- 413

414 Conversion Cable 1 6.17- 414

WWW.SMOOTHFITNESS.COM

7

6.17MOTORIZDTREADMILL



PARTS LIST

Part No. Description Qty. Order No.

500

501 Motor Hood -Upper 1 6.17- 501

502 Motor Hood Decorative Cover- Left 1 6.17- 502

503 Motor Hood Decorative Cover- Right 1 6.17- 503

504 Motor Hood-Bottom 1 6.17- 504

505 Driving Motor 1 6.17- 505

506 Driving Motor Base 1 6.17- 506

507 Transportation Wheel-Front 2 6.17- 507

508 Driving Belt 1 6.17- 508

509 Plastic Clamp-Upper 2 6.17- 509

510 Plastic Clamp-Bottom 2 6.17- 510

511 Bracket 2 6.17- 511

512 Fold Up Support 1 6.17- 512

513 Shock 1 6.17- 513

514 Fold Up Support Wheel 1 6.17- 514

515 Fold Up Support Bush 2 6.17- 515

516 Elevation Support Frame 1 6.17- 516

600

601 Base Frame 1 6.17- 601

602 Upright Base Cover -L-L 1 6.17- 602

603 Upright Base Cover -L-R 1 6.17- 603

604 Upright Base Cover -L-Back 1 6.17- 604

605 Upright Base Cover -R-L 1 6.17- 605

606 Upright Base Cover -R-L 1 6.17- 606

607 Upright Base Cover -L-Back 1 6.17- 607

608 Power Switch Plate Base 1 6.17- 608

609 Power Breaker 1 6.17- 609

610 Power Switch 1 6.17- 610

611 Power Switch Board 1 6.17- 611

612 Electric Outlet 1 6.17- 612

613 Rubber Cushion 4 6.17- 613

614 Fold Up Locker 1 6.17- 614

615 Spring 1 6.17- 615

616 Transportation Wheel Pedal 1 6.17- 616

617 Transportation Wheel Holder 1 6.17- 617

618 Transportation Wheel-Rear 1 6.17- 618

700

701 Running Belt 1 6.17- 701

702 Side Rail 2 6.17- 702

703 Side Rail Insert Bar 2 6.17- 703

704 Left Rear End Cap-Outside 1 6.17- 704

705 Left Rear End Cap-Inner 1 6.17- 705

706 Left Rear End Cap-Decorative Cover 1 6.17- 706

707 Right Rear End Cap-Outside 1 6.17- 707

708 Right Rear End Cap-Inner 1 6.17- 708

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

8



PARTS LIST

Part No. Description Qty. Order No.

709 Left Rear End Cap-Decorative Cover 1 6.17- 709

710 Running Deck 1 6.17- 710

711 Running Deck Rubber Cushion 8 6.17- 711

712 Side Rail Guider 8 6.17- 712

800

801 Φ 2x6mm Screw 8 6.17- 801

802 Φ 8 Washer 24 6.17- 802

803 Φ 3.5x14mm Screw 27 6.17- 803

804 M 8x45mm Allen Head Cap Bolt 8 6.17- 804

805 M 8x51mm Allen Head Cap Bolt 4 6.17- 805

806 Φ 4x14mm Screw 76 6.17- 806

807 M 8x10mm Allen Head Cap Bolt 2 6.17- 807

808 M 8x70mm Allen Head Cap Bolt 2 6.17- 808

809 M 6x45mm Allen Head Cap Bolt 3 6.17- 809

810 M 8x30mm Bolt 10 6.17- 810

811 Φ 6 Washer 3 6.17- 811

812 M 10x38mm Allen Head Cap Bolt 2 6.17- 812

813 M10 Nut 5 6.17- 813

814 M 10x30mm Allen Head Cap Bolt 1 6.17- 814

815 M 4x12mm Bolt 4 6.17- 815

816 M 10x28mm Allen Head Cap Bolt 2 6.17- 816

817 M 8 Nut 6 6.17- 817

818 M 10x43mm Allen Head Cap Bolt 1 6.17- 818

819 Φ 10 Washer 2 6.17- 819

820 M 8x47mm Bolt 1 6.17- 820

821 M 8x85mm Motor Adjustment Bolt 1 6.17- 821

822 Φ 35x6mm Spring Washer 2 6.17- 822

823 Φ 25x12mm PU Cushion 1 6.17- 823

824 M 8x12mm Allen Head Cap Screw 2 6.17- 824

825 M 10x116mm Allen Head Bolt 1 6.17- 825

826 M 10x66mm Allen Head Cap Screw 1 6.17- 826

827 M 8x30mm Allen Head Cap Bolt 4 6.17- 827

828 Snap Link 1 6.17- 828

829 Φ 4x19mm Screw 16 6.17- 829

830 M 8x18mm Allen Head Cap Bolt 4 6.17- 830

831 M 16x139mm Bolt 2 6.17- 831

832 M 6 Nut 1 6.17- 832

833 M 8x52mm Allen Head Cap Bolt 1 6.17- 833

834 M 10x44mm Allen Head Cap Bolt 1 6.17- 834

835 M 8x38mm Allen Head Cap Bolt 1 6.17- 835

836 M 5x14mm Bolt 4 6.17- 836

837 Φ 6 Plastic Insert 4 6.17- 837

838 Φ 6.2 Plastic Insert 14 6.17- 838

839 Φ3x14 mm Screw 4 6.17- 839

840 Φ4x25 mm Screw 2 6.17- 840

841

Φ6﹢ Washer

2 6.17- 841

WWW.SMOOTHFITNESS.COM

9

6.17MOTORIZDTREADMILL



PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

10



PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

WWW.SMOOTHFITNESS.COM

11

6.17MOTORIZDTREADMILL



PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

12



PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

WWW.SMOOTHFITNESS.COM

13

6.17MOTORIZDTREADMILL



PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

14



PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

WWW.SMOOTHFITNESS.COM

15

6.17MOTORIZDTREADMILL



PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

16



ASSEMBLY

STEP 1:

A. Remove the carton and all packing material from the treadmill and

place the treadmill on the floor in an open area.

B. Raise up the Upright (301), and secure the Left Upright using two

M8x18mm Allen Head Cap Bolt (830), two Φ8 Washer (802), one

M8x51mm Bolt (805) and one Φ8 Washer (802).

C. Secure the Right Upright using two M8x18mm Allen Head Cap Bolt

(830), two Φ8 Washer (802), one M8x51mm Bolt (805) and one Φ8

Washer (802)

.

802

X 6

805

X 2

830

X 4

WWW.SMOOTHFITNESS.COM

17

6.17MOTORIZDTREADMILL



ASSEMBLY

STEP 2:

A. Rotate the Console Assembly (203) up and hold while the bolts are inserted.

B. Secure the Right Handbar with two M8x45mm Allen Head Cap Bolt (804)

and two Φ

8 Washer (802).

C. Secure the Left Handbar with two M8x45mm Allen Head Cap Bolt (804) and

two Φ

8 Washer (802) .

802

X 4

804 X 4

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

18



ASSEMBLY

STEP 3:

NOTE: Refer to

FOLDING INSTRUCTION on the page 22.

A. Fold up the running deck until it locks in correct position.

B. Attach Right Upright base cover- back (604) to the right upright, secure

with one 4 x 14mm screw (806).

C. Attach Left Upright base cover- back to the left upright, secure with

one 4 x 14mm screw.

806

X

2

WWW.SMOOTHFITNESS.COM

19

6.17MOTORIZDTREADMILL



ASSEMBLY

STEP 4:

A. Attach the Handbar Cover-LL (304) then attach the Handbar Cover-LR

(305), secure with one 4 x 14mm screw.

B. Attach the Handbar Cover-RR (308) then attach the Handbar Cover-RL

(307), secure with one 4 x 14mm screw.

806

X 2

WWW.SMOOTHFITNESS.COM

6.17 MOTORIZD TREADMILL

20



ASSEMBLY

STEP 5:

A. Loosen Handlebar securing bolts using the 6mm Allen key and push the Handlebar

down until the handlebar covers are fully seated in the uprights.

B. Tighten the Handlebar securing bolts.

C. Insert the Screw covers (310) to the uprights as shown the Close-up 3.

310

X 2

WWW.SMOOTHFITNESS.COM

Page is loading ...

Smooth Fitness 2 User manual

This manual is also suitable for

Smooth Fitness 2 User manual

Related papers

Other documents