Intermec EasyCoder 401 User manual

Category
Print & Scan
Type
User manual

Intermec EasyCoder 401 is a versatile linerless label printer designed for commercial applications. It excels in printing linerless self-adhesive labels, offering 60% more labels per roll compared to traditional labels with liner. The printer's direct thermal printing technology provides darker images with longer lifespans, and the labels exhibit higher resistance to chemicals, scratching, and UV light.

Intermec EasyCoder 401 is a versatile linerless label printer designed for commercial applications. It excels in printing linerless self-adhesive labels, offering 60% more labels per roll compared to traditional labels with liner. The printer's direct thermal printing technology provides darker images with longer lifespans, and the labels exhibit higher resistance to chemicals, scratching, and UV light.

EasyCoder 401
LinerLess Label Printer
P/N 1-960408-01
Edition 2
September 1998
User’s Manual
Intermec EasyCoder 401 Linerless – User's Manual
1
CONTENTS
Introduction Presentation of the EasyCoder 401 Linerless models .................................. 3
Get to Know Your Printer Front View ................................................................................................. 4
Rear View .................................................................................................. 4
Paper Stock Compartment .......................................................................... 5
Paper Load EasyCoder 401 Linerless Tear-Off (LLT).................................................... 6
EasyCoder 401 Linerless Cutter (LLC)....................................................... 9
Maintenance Printhead Cleaning ................................................................................... 12
External Cleaning ..................................................................................... 14
Cutter Cleaning ........................................................................................ 15
Printhead Replacement ............................................................................. 16
Troubleshooting ....................................................................................... 17
Intermec
EasyCoder 401 Linerless
User's Manual
Edition 2, September 1998
Part No. 1-960408-01
Intermec EasyCoder 401 Linerless – User's Manual
2
Information in this manual is subject to change without prior notice and does not represent a
commitment on the part of Intermec Printer AB.
© Copyright Intermec PTC AB, 1998. All rights reserved. Published in Sweden.
EasyCoder, Fingerprint, and LabelShop are registered trademarks of Intermec Technologies Corp.
Apple and Macintosh are registered trademarks of Apple Computer Inc.
Microsoft is a registered trademark of Microsoft Corporation.
Speedo is a trademark of Bitstream, Inc.
TrueType is a trademark of Apple Computer Inc.
Windows is a trademark of Microsoft Corporation.
FCC Notice
United States of America
WARNING:
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance
with the instructions manual, may cause interference to radio communications. It has been tested and found to
comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures may be required to correct the interference.
DOC Notice
Canada
Canadian Dept. of Communication
REGULATIONS COMPLIANCE
(DOC-A)
This digital apparatus does not exceed the class A limits for radio noise emissions from a digital apparatus as set out
in the radio interference regulations of the Canadian Department of Communication.
✳ ✳ ✳
Ministère des Communications du Canada
CONFORMITE DE REGLEMENTS
(DOC-A)
Le présent appareil numérique n´émet pas de bruits radio-électriques dépassant les limites applicables aux appareils
numériques de classe A prescrites dans le règlement sur brouillage radioélectrique édicté par le Ministère des
Communications du Canada.
Intermec EasyCoder 401 Linerless – User's Manual
3
INTRODUCTION
The Intermec EasyCoder 401 Linerless printers
come in two main models:
EasyCoder 401 Linerless Tear-Off (LLT)
EasyCoder 401 Linerless Cutter (LLC)
Both models are direct thermal printers intended for
printing linerless self-adhesive labels. The main
difference between the models is that the Tear-Off
model uses pre-perforated linerless strip with black
marks which is manually torn off, whereas the
Cutter model has an automatic paper cutter that cuts
off labels from continuous linerless strip with or
without black marks.
Linerless printing eliminates the liner (backing
paper), that usually protects the adhesive side of
self-adhesive labels, and is thus more economi-
cal with 60% more labels per roll, which gives
fewer paper reloads. Variable label length allows
for fewer label sizes in stock. The environment
also benefits from less waste.
The linerless paper gives higher resistance against
chemicals, scratching and UV light and a darker
image with longer life than common direct ther-
mal labels with liner.
EasyCoder 401 Linerless printers can be controlled
by a host computer using standard or custom-made
application software, e.g. the various Intermec
LabelShop label-design programs for Microsoft
Windows. Custom-made applications can be writ-
ten in the versatile Basic-inspired Intermec Finger-
print programming language.
Optionally, the EasyCoder 401 Linerless printers
can be fitted with a scalable fonts kit that allows the
use of outline fonts in Speedo and TrueType format
and a real-time clock circuit. The Tear-Off model
can also be fitted with a label-taken sensor or a
paper cutter.
Information on the different options can be found in
the Intermec EasyCoder 401 Linerless Technical
Manual, which also describes installation and com-
puter connection.
The following manuals may be of interest to the
operator or programmer:
Intermec EasyCoder 401 LL, Operator's Guide
Intermec Shell Standard 4.01, Startup Manual
Intermec EasyCoder 401 LL Technical Manual
Intermec Fingerprint Direct 6.13, Programmer's
Guide
Intermec Fingerprint 6.13, Programmer's Guide
Intermec Fingerprint 6.13, Reference Manual
Intermec LabelShop, various manuals
EasyCoder 401 Linerless Tear-Off EasyCoder 401 Linerless Cutter
401
LL
40
1
L
L
Intermec EasyCoder 401 Linerless – User's Manual
4
Thermal Printer 401
N
3
0
9
1
-
4
0
1
0
1
1
-1
1
S
e
ria
l #
115-230V 2.6-1.3A 50-60H
z
INTERMEC PRINTER AB
MADE IN SWEDEN
1
2
2
2
3
T
h
i
s
e
q
u
i
p
m
e
n
t
c
o
m
p
l
i
e
s
w
i
t
h
t
h
e
r
e
q
u
i
r
e
m
e
n
t
s
f
o
r
a
C
l
a
s
s
A
c
o
m
p
u
t
i
n
g
d
e
v
i
c
e
i
n
F
C
C
R
u
l
e
s
P
a
r
t
1
5
S
u
b
p
a
r
t
J
.
O
p
e
r
a
t
i
o
n
o
f
t
h
i
s
d
e
v
i
c
e
i
n
a
r
e
s
i
d
e
n
t
i
a
l
a
r
e
a
m
a
y
c
a
u
s
e
h
a
r
m
f
u
l
i
n
t
e
r
f
e
r
e
n
c
e
r
e
q
u
i
r
i
n
g
t
h
e
u
s
e
r
t
o
t
a
k
e
w
h
a
t
e
v
e
r
s
t
e
p
s
m
a
y
b
e
n
e
c
e
s
s
a
r
y
t
o
c
o
r
r
e
c
t
t
h
e
i
n
t
e
r
f
e
r
e
n
c
e
.
401 LL
GET TO KNOW YOUR PRINTER
Print Key
Label Taken Sensor
(option for EC 401 LLT only)
Display Window
LED Indicator Lamps
Cutter Interface Connector
Front Door (or cutter)
The front door can be swung open and removed
from the hinges. In EasyCoder 401 LLC, it is
replaced by a cutter unit, see next page.
Continued!
Voltage Switch
Provision for Parallel Interface Board
Display Contrast Adjustment
Main Switch
Mains Receptacle
Machine Sign
Serial Interface Connector "uart1:"
This illustration shows an EasyCoder 401 LLT printer.
From behind, both models look identical.
Intermec EasyCoder 401 Linerless – User's Manual
5
The paper stock compartment becomes accessible when the
right-hand and front doors or cutter are swung open. Although
the printer is operable when the doors are left opened or
completely removed, you are strongly recommended to keep
them closed during normal operation, so as to prevent the printer
mechanism from being exposed to dust.
This illustration shows an EasyCoder 401 LLC printer.
An adapter for 76 mm (3") paper roll cores is included in the
delivery and can be fitted on the paper supply spool.
Lock the adapter by means of the screw, making sure that the
screw hits the evenly rounded plastic surface, rather than the leaf
spring or the cam.
L
o
a
d
P
r
i
n
t
IMPORTANT PRINTHEAD AND RIBBON INFORMATION
T
h
e
u
s
e
o
f
a
n
y
t
h
e
r
m
a
l
t
r
a
n
s
f
e
r
r
i
b
b
o
n
s
, o
th
e
r
t
h
a
n
t
h
o
s
e
s
u
p
p
li
e
d
b
y
U
B
I
,
w
i
l
l
i
n
v
a
l
i
d
a
t
e
th
e
p
r
i
n
t
h
e
a
d
w
a
r
r
a
n
t
y
.
U
B
I
t
h
e
r
m
a
l t
r
a
n
s
f
e
r
r
ib
b
o
n
s
a
r
e
e
n
g
in
e
e
r
e
d
s
p
e
c
if
ic
a
l
ly
f
o
r
t
h
is
p
r
in
t
h
e
a
d
.
T
h
e
q
u
a
lit
y
o
f
t
h
e
r
m
a
l
a
n
d
t
h
e
r
m
a
l
t
r
a
n
s
f
e
r
m
e
d
ia
s
u
p
p
lie
s
in
t
h
is
p
r
in
t
e
r
is
a
ls
o
o
f
g
r
e
a
t
im
p
o
r
ta
n
c
e
f
o
r
t
h
e
q
u
a
lit
y
o
f
p
r
in
ti
n
g
b
a
r
c
o
d
e
s
a
n
d
a
lo
n
g
lif
e
o
f
t
h
e
p
r
in
t
h
e
a
d
. U
B
I
h
a
s
c
a
r
e
fu
lly
m
a
t
c
h
e
d
t
h
e
p
a
p
e
r
w
e
r
e
c
o
m
m
e
n
d
/
p
r
o
v
id
e
t
o
t
h
e
n
e
e
d
s
o
f
t
h
is
p
r
in
t
e
r
. W
e
t
h
e
r
e
f
o
r
e
s
t
r
o
n
g
ly
a
d
v
is
e
o
f
u
s
in
g
o
n
ly
U
B
I
r
e
c
o
m
m
e
n
d
e
d
/
p
r
o
v
id
e
d
s
u
p
p
lie
s
t
o
e
n
s
u
r
e
a
h
ig
h
q
u
a
lity
p
r
in
tin
g
.
T
E
A
R
-O
F
F
401 LL
GET TO KNOW YOUR PRINTER, cont'd.
Paper Supply Spool
Printhead Lift Knob
Thermal
Printhead
Slack Absorber
Tear-Off Edge
4
0
1 L
L
Paper Cutter
(incl. LTS)
Intermec EasyCoder 401 Linerless – User's Manual
6
PAPER LOAD
EasyCoder 401 LLT
Open the front and right-hand doors. Turn the printhead lift knob to “Load” position.
Remove the empty paper core, if any.
In case of paper roll with a 76.2 mm (3 inches) core, first
fit the adapter on the paper supply spool.Fit a new paper roll on the tip of the paper supply spool.
1
3
5a 5b
4
2
4
01
LL
Turn the label slack absorber clockwise
so it snap-locks into open position.
38-40 mm
(1.5")
76 mm
(3")
Intermec EasyCoder 401 Linerless – User's Manual
7
PAPER LOAD, cont'd.
EasyCoder 401 LLT
6
8 9
7
Push the paper inwards as far as it will go in the print
unit. Make sure that it runs under the label stop sensor.
Pull out the paper and thread it under the slack absorber
and through the print unit as illustrated. Then push the
roll inwards as far as it will go.
Turn the printhead lift knob to “Print” position.
Release the slack absorber (1). Adjust the green guide
ring so the paper is guided with a minimum of play (2). Close the front and side doors.
10
4
0
1
L
L
11
I
M
P
O
R
T
A
N
T
P
R
I
N
T
H
E
A
D
A
N
D
R
I
B
B
O
N
I
N
F
O
R
M
A
T
I
O
N
T
h
e
u
s
e
o
f
a
n
y
t
h
e
r
m
a
l
t
r
a
n
s
f
e
r
r
i
b
b
o
n
s
,
o
t
h
e
r
t
h
a
n
t
h
o
s
e
s
u
p
p
l
i
e
d
b
y
U
B
I
,
w
i
l
l
i
n
v
a
l
i
d
a
t
e
t
h
e
p
r
i
n
t
h
e
a
d
w
a
r
r
a
n
t
y
.
U
B
I
t
h
e
r
m
a
l
t
r
a
n
s
f
e
r
r
ib
b
o
n
s
a
r
e
e
n
g
i
n
e
e
r
e
d
s
p
e
c
i
f
i
c
a
l
ly
f
o
r
t
h
i
s
p
r
i
n
t
h
e
a
d
.
T
h
e
q
u
a
l
i
t
y
o
f
t
h
e
r
m
a
l
a
n
d
t
h
e
r
m
a
l
t
r
a
n
s
f
e
r
m
e
d
i
a
s
u
p
p
l
ie
s
in
t
h
i
s
p
r
i
n
t
e
r
i
s
a
l
s
o
o
f
g
r
e
a
t
i
m
p
o
r
t
a
n
c
e
f
o
r
t
h
e
q
u
a
l
i
t
y
o
f
p
r
i
n
t
in
g
b
a
r
c
o
d
e
s
a
n
d
a
l
o
n
g
l
i
f
e
o
f
t
h
e
p
r
i
n
t
h
e
a
d
.
U
B
I
h
a
s
c
a
r
e
f
u
l
ly
m
a
t
c
h
e
d
t
h
e
p
a
p
e
r
w
e
r
e
c
o
m
m
e
n
d
/
p
r
o
v
i
d
e
t
o
t
h
e
n
e
e
d
s
o
f
t
h
i
s
p
r
i
n
t
e
r
.
W
e
t
h
e
r
e
f
o
r
e
s
t
r
o
n
g
l
y
a
d
v
i
s
e
o
f
u
s
i
n
g
o
n
l
y
U
B
I
r
e
c
o
m
m
e
n
d
e
d
/
p
r
o
v
i
d
e
d
s
u
p
p
l
i
e
s
t
o
e
n
s
u
r
e
a
h
i
g
h
q
u
a
l
it
y
p
r
i
n
t
in
g
.
TEAR-OFF
4
0
1
L
L
This diagram shows the label web path.
2.
1.
Intermec EasyCoder 401 Linerless – User's Manual
8
Feed out two blank labels by pressing the <Print> key
twice.
PAPER LOAD, cont'd.
EasyCoder 401 LLT
12
13
401 LL
Tear of the labels by pulling down at the outer side.
# 1
# 2
2x
401 LL
Intermec EasyCoder 401 Linerless – User's Manual
9
PAPER LOAD
EasyCoder 401 LLC
Open the cutter unit and the right-hand door.
1
3
5a 5b
4
2
-
401 LL
Turn the printhead lift knob to “Load” position.
Remove the empty paper core, if any.
In case of paper roll with a 76.2 mm (3 inches) core, first
fit the adapter on the paper supply spool.Fit a new paper roll on the tip of the paper supply spool.
Turn the label slack absorber clockwise
so it snap-locks into open position.
38-40 mm
(1.5")
76 mm
(3")
Intermec EasyCoder 401 Linerless – User's Manual
10
PAPER LOAD, cont'd.
EasyCoder 401 LLC
6
8
10 11
9
Turn the printhead lift knob to “Print” position.
7
Thread the paper through the cutter so the equivalent of
at least one label protrudes outside the cutter.
Pull out the paper and thread it under the slack absorber
and through the print unit as illustrated. Then push the
roll inwards as far as it will go.
IM
PO
RT
AN
T PR
INT
H
E
A
D
A
N
D
RIB
B
ON
IN
F
OR
M
A
TIO
N
T
h
e
u
s
e o
f a
n
y
th
e
rm
a
l
t
ran
sfe
r
rib
b
o
n
s
, o
th
e
r t
h
a
n
t
h
o
s
e
su
p
p
lie
d
b
y
U
B
I, w
il
l
in
v
a
lid
a
te
t
h
e
p
ri
n
th
e
a
d
w
a
rra
nt
y
. U
B
I
th
e
rm
a
l t
ra
ns
fe
r rib
b
o
n
s
a
re
e
n
g
in
e
er
ed
s
pe
c
ific
a
lly f
o
r t
h
is
p
rin
th
e
a
d
T
he
q
u
a
lit
y
o
f t
h
e
rm
a
l a
nd
th
erm
a
l t
ra
ns
fe
r m
e
dia
s
u
p
p
lie
s
in
th
is
p
rin
te
r is a
ls
o
o
f g
r
e
a
t im
p
o
rt
a
f
o
r
th
e
q
ua
lity
o
f
p
rin
t
in
g b
a
r c
od
es
a
nd
a
lo
ng
life
o
f th
e p
rin
th
e
a
d
. U
B
I h
a
s
c
a
re
fu
lly
m
a
tc
h
e
d
p
ap
e
r w
e
r
e
c
o
m
m
e
n
d
/p
r
o
v
id
e
to
t
h
e
n
ee
d
s
o
f t
h
is
p
rint
e
r. W
e t
h
e
re
fo
re
st
ro
ng
ly
a
d
v
is
e
o
f u
s
i
o
n
ly
U
B
I
re
c
o
m
m
e
n
d
e
d
/p
ro
v
id
e
d
s
u
p
p
l
ie
s
t
o
en
s
u
re
a
h
ig
h
q
u
a
lit
y
p
rin
tin
g.
T
E
A
R
-
O
F
F
401 LL
Push the paper inwards as far as it will go in the print
unit. Make sure that it runs under the label stop sensor.
This diagram shows the label web path.
Release the slack absorber (1). Adjust the green guide
ring so the paper is guided with a minimum of play (2).
2.
1.
Intermec EasyCoder 401 Linerless – User's Manual
11
PAPER LOAD, cont'd.
EasyCoder 401 LLC
12
13
Close the cutter unit while pulling at the end of the paper.
Close the right-hand door.
Feed out and cut two blank copies by pressing the
<Print> key twice.
-
401 LL
# 2
# 1
4
0
1
L
L
2x
Intermec EasyCoder 401 Linerless – User's Manual
12
L
o
a
d
P
r
i
n
t
PRINTHEAD CLEANING
Open the front and right-hand doors.
1
3 4
2
Remove the paper supply.
Cleaning of the printhead on a regular basis, preferably in
connection with paper reload, is important for the life of the
printhead and for the printout quality. Below is a description on
how to clean the printhead by means of Cleaning Cards. If
additional cleaning is required, e.g. for removing adhesive
residue from the print roller, dispenser edge, or label path, use
a cotton swab moistened with isopropyl alcohol.
Caution:
Isopropyl alcohol [(CH
3
)
2
CHOH; CAS 67-63-0] is a highly
flammable, moderately toxic and mildly irritating substance.
Cleaning Card
T
h
i
s
p
r
e
-
s
a
t
u
r
a
t
e
d
d
i
s
p
o
s
a
b
l
e
T
h
e
r
m
a
l
P
r
i
n
t
e
r
C
l
e
a
n
i
n
g
C
a
r
d
i
s
d
e
s
i
g
n
e
d
t
o
s
a
f
e
l
y
a
n
d
e
f
f
e
c
t
i
v
e
l
y
r
e
m
o
v
e
a
l
l
d
i
r
t
,
i
n
k
,
t
a
p
e
,
r
e
s
i
d
u
e
,
a
d
h
e
s
i
v
e
a
n
d
o
t
h
e
r
c
o
n
t
a
m
i
n
a
n
t
s
f
r
o
m
T
h
e
r
m
a
l
P
r
i
n
t
H
e
a
d
s
.
T
h
i
s
C
l
e
a
n
i
n
g
c
a
r
d
w
i
l
l
i
m
p
r
o
v
e
p
r
i
n
t
q
u
a
l
i
t
y
a
n
d
t
h
e
l
i
f
e
o
f
t
h
e
T
h
e
r
m
a
l
P
r
i
n
t
H
e
a
d
.
N
O
T
E
:
F
o
r
T
h
e
r
m
a
l
T
r
a
n
s
f
e
r
P
r
i
n
t
e
r
s
,
r
e
m
o
v
e
r
i
b
b
o
n
.
O
p
e
n
p
o
u
c
h
a
n
d
r
e
m
o
v
e
E
a
s
y
C
o
d
e
r
C
l
e
a
n
i
n
g
C
a
r
d
.
L
i
f
t
t
h
e
r
m
a
l
p
r
i
n
t
h
e
a
d
a
n
d
i
n
s
e
r
t
E
a
s
y
C
o
d
e
r
C
l
e
a
n
i
n
g
C
a
r
d
.
L
o
w
e
r
p
r
i
n
t
h
e
a
d
a
n
d
p
r
e
s
s
F
E
E
D
o
r
P
R
I
N
T
.
I
f
p
r
i
n
t
e
r
r
e
t
u
r
n
s
a
n
e
r
r
o
r
m
e
s
s
a
g
e
,
r
e
p
e
a
t
t
h
e
p
r
o
c
e
d
u
r
e
b
u
t
p
r
e
s
s
F
E
E
D
o
r
P
R
I
N
T
b
e
f
o
r
e
l
o
w
e
r
i
n
g
t
h
e
p
r
i
n
t
h
e
a
d
.
T
h
e
p
r
i
n
t
e
r
w
i
l
l
s
t
a
r
t
f
e
e
d
i
n
g
a
f
t
e
r
p
r
i
n
t
h
e
a
d
i
s
l
o
w
e
r
e
d
.
A
l
l
o
w
a
f
e
w
s
e
c
o
n
d
s
f
o
r
E
a
s
y
C
o
d
e
r
C
l
e
a
n
i
n
g
C
a
r
d
t
o
d
r
y
,
t
h
e
n
i
n
s
e
r
t
d
r
y
c
a
r
d
f
o
r
a
s
e
c
o
n
d
t
i
m
e
,
f
e
e
d
t
o
r
e
m
o
v
e
r
e
m
a
i
n
i
n
g
c
o
n
t
a
m
i
n
a
t
i
o
n
.
R
e
m
o
v
e
C
l
e
a
n
i
n
g
C
a
r
d
a
n
d
d
i
s
p
o
s
e
o
f
p
r
o
p
e
r
l
y
.
U
s
e
E
a
s
y
C
o
d
e
r
C
l
e
a
n
i
n
g
C
a
r
d
s
b
e
f
o
r
e
i
n
s
e
r
t
i
n
g
e
v
e
r
y
r
o
l
l
o
f
l
a
b
e
l
s
t
o
c
k
o
r
t
i
c
k
e
t
s
t
o
c
k
.
W
o
r
k
s
o
n
a
l
l
E
a
s
y
C
o
d
e
r
P
r
i
n
t
e
r
s
D
i
r
e
c
t
i
o
n
s
R
E
C
O
M
M
E
N
D
E
D
U
S
A
G
E
:
S
A
F
E
E
A
S
Y
E
F
F
E
C
T
I
V
E
P
R
O
T
E
C
T
S
Y
O
U
R
E
Q
U
I
P
M
E
N
T
Turn the printhead lift knob to “Load” position.
Open the Cleaning Card pouch. The cleaning card
contains isopropyl alcohol, see “Caution” above.
4
0
1
LL
Intermec EasyCoder 401 Linerless – User's Manual
13
Load
Print
2.5 cm
(1")
1.
2.
LL
L
o
a
d
P
rin
t
2.5 cm
(1")
1.
2.
L
Lo
a
d
P
rin
t
401 LL
1.
Load
Print
01
LL
PRINTHEAD CLEANING, cont'd.
5
7
9 10
8
6
Pull out the cleaning card. Repeat if necessary.
Insert most of the cleaning card under the printhead (1).
Turn the printhead lift knob to “Print” position (2).
Pull out the cleaning card (1) and turn the printhead
lift knob to “Load” position (2).
Insert the cleaning card under the printhead again (1).
Turn the printhead lift knob to “Print” position (2).
Allow the cleaned parts to dry before
loading the printer with paper.
Wait for approx. 30 seconds.
12
11
10
9
8
7
6
5
4
3
2
1
30 s.
Intermec EasyCoder 401 Linerless – User's Manual
14
401 LL
EXTERNAL CLEANING
1
3
4
2
Always remove the power cord before cleaning!
Wipe external surface with a soft cloth moistened with
water and, if necessary, a mild detergent.
Never spray the printer. Protect the printer from water
when cleaning the premises.
Never use any sharp tools for removing stuck labels.
The printhead and the print roller are easily damaged.
T
EA
R
-O
FF
401 LL
IMPORTANT!
It is recommended to clean all surfaces in contact with the paper, including the
rubber roller, from adhesive residue at an interval of max. 3 km of paper feed
(corresponds approximately to 20 full size paper rolls). Use a cleaning card or a lint-
free cotton swab or cloth soaked with isopropyl alcohol.
Intermec EasyCoder 401 Linerless – User's Manual
15
CUTTER CLEANING
EasyCoder 401 LLC
Open the cutter.
1
3 4
2
Disconnect the brace and open the anvil blade by
lifting the arm. Wipe clean the anvil blade with the swab.
Regular cleaning from adhesive residue at the cutting edge of the
anvil blade at an interval of approximately 50,000 cuts is
essential for troublefree operation. Use WD-40 or a similar
substance
1
. If additional cleaning of the interior of the cutter unit
is required, use a cotton swab moistened with isopropyl alcohol.
Caution:
WD-40 is an anti-corrosion spray lubricant manufactured
by WD-40 Company Ltd., Milton Keynes, England,
which contains 50% alifatic petroleum distillate.
It is highly flammable and may be harmful if inhaled or
consumed and at prolonged skin contact.
Before use, carefully read the warning text on the container.
Soak a cotton swab with WD-40 multi-spray or similar
1
.
Close the anvil blade and lock it with the brace.
Then close the cutter.
-
4
0
1
LL
1
/. In food industry and retail applications
subject to specific regulations, the WD-
40 could be replaced with a pure
consumable vegetable oil. After dis-
solving the residue, carefully wipe clean
the anvil blade.
-
401 LL
Intermec EasyCoder 401 Linerless – User's Manual
16
PRINTHEAD REPLACEMENT
The quick-mount thermal printhead is easy to replace:
Turn off the printer.
Open the front and right-hand doors.
Lift the printhead and remove the paper stock.
Turn the printhead lock handle counter-clockwise to open posi-
tion, see illustration.
Remove the printhead assy carefully as far as the cables allow.
Remove the two printhead cables by pulling at the connectors.
If you want to change the lateral position of the printhead, move
the #T20 Torx screw to its alternative position.
Connect the two cables to the printhead.
Fit the replacement printhead assy back into the bracket so the
guide screw fits into its slot and the rear end of the assy is held by
the two lugs.
Turn the locking handle clockwise to locked position.
Load paper. Then lower the printhead.
Turn on the power. At power-up, the printer will automatically
reset itself to the characteristics of the printhead in regard of head
resistance.
Close the front and right-hand door and the printer is ready for
operation.
Lug
Guide Screw
Slot
Lug
Open Position
Lock Handle
Locked Position
Alternative position
for guide screw
Printhead assy
Slot (for alternative position
of guide screw)
Intermec EasyCoder 401 Linerless – User's Manual
17
TROUBLE SHOOTING
The list below is intended to help the operator to correct possible
printout troubles or flaws in printout quality, and to decide when
assistance from the Service dept. of the nearest Intermec dis-
tributor is required. Note that most problems are due to operat-
ing errors or normal wear of the printhead.
Symptom Possible Cause Remedy Refer to
Overall weak printout Adhesive build-up on printhead Clean printhead User's Manual
Wrong Paper type setup Change setup Technical Manual
Low Contrast setup Change setup Technical Manual
Printhead pressure too low Adjust both knobs Technical Manual
Worn printhead Replace printhead User's Manual
Wrong printhead voltage Replace CPU board Call Service
Printout weaker on one side Uneven printhead pressure Adjust outer knob Technical Manual
Weak spots Foreign particles on paper Wipe paper clean n.a.
Paper fibres on printhead Clean printhead User's Manual
Poor paper quality Use other media Technical Manual
Worn printhead Replace printhead User's Manual
Worn pressing roller Check/replace Call Service
Overall dark printout Wrong Paper Type setup Change setup Technical Manual
Contrast setup value too high Change setup Technical Manual
Printhead pressure too high Adjust both knobs Technical Manual
Wrong printhead voltage Replace CPU board Call Service
Excessive bleeding Wrong Paper Type setup Change setup Technical Manual
Contrast setup value too high Change setup Technical Manual
Printhead pressure too high Adjust both knobs Technical Manual
Faulty energy control Replace CPU board Call Service
White lines along paper web Printhead dirty Clean printhead User's Manual
Missing dots on printhead Replace printhead User's Manual
Large part of dot line missing Wrong X-start or Width setup Change setup Technical Manual
Failing printhead Replace printhead User's Manual
Failing strobe signal Check CPU-board Call Service
Last part of label missing Too small image buffer Increase buffer Technical Manual
Printout missing along inner edge Bad paper alignment Adjust User's Manual
X-start setup value too low Increase Technical Manual
Paper jams in printer Adhesive residue on printer parts Clean User's Manual
Adhesive residue in cutter Clean User's Manual
Compressed printing along web Too high release force required Change paper n.a.
Inferior ladder bar code printing Linerless less suited for ladder bar codes Change the layout n.a.
Bad cutting Adhesive residue on anvil blade Clean User's Manual
Paper jams in cutter unit Adhesive residue inside cutter unit Clean User's Manual
Parts of labels stuck inside cutter unit Clean User's Manual
Cutter does not cut Safety switch defect or not activated Check arm is closed User's Manual
Check switch Call Service
Wrong Fingerprint version (< 6.1) Check version Shell Manual
Printer does not feed LTS erroneously detects label not taken Adjust LTS Technical Manual
Intermec EasyCoder 401 Linerless – User's Manual
18
NOTES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Intermec EasyCoder 401 User manual

Category
Print & Scan
Type
User manual

Intermec EasyCoder 401 is a versatile linerless label printer designed for commercial applications. It excels in printing linerless self-adhesive labels, offering 60% more labels per roll compared to traditional labels with liner. The printer's direct thermal printing technology provides darker images with longer lifespans, and the labels exhibit higher resistance to chemicals, scratching, and UV light.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI