Motorola MC67 Quick start guide

Category
Rechargeable batteries
Type
Quick start guide
2
3
6
11
5
8
1
2
3
7
9
10
12
8
3
3
7
2
2
3
2
2
8
1
2
2
3
2
4
9
2
5
7
6
5
18
17
13
19
14
15
21
16
20
22
23
7
2
2
3
2
2
8
6
5
9
9
1 Talk
2 Navigation
3 Scan/Action Button
4 End
5 Orange Key
6 Blue Key
7 Home
8 Menu
9 Back
Numeric Keypad
Alpha-Numeric Keypad
Orange Key
>
>
Press the Orange key once to lock the
keypad into Alpha state.
Press the Orange key a second time to
return to the normal state.
Notifications
Charging/Battery Status LED:
Data Capture LED:
Slow blinking amber: Battery charging
Solid amber: Fully charged
Fast blinking amber: Charging error
Green: Good Decode
Data Capture
Charging/Battery Status
Radio Status
Radio Status LED:
Green: RF active
Note: Remove protective shipping film that covers the touch screen, exit
window and camera window before using.
Press the Orange key once to lock the keypad into
Alpha state.
Press the Orange key a second time to return to the
normal state.
Press the Blue key once to activate this state, followed
by another key.
Blue Key
>
Orange Key
>
>
4
(Note 1)
FEATURES CARD INSTALLATION
MicroSD Card Installation (Optional)
1. Remove the handstrap.
2. Lift the rubber access door.
3. Slide the SIM card holder up to
unlock.
4. Lift the SIM card holder.
5. Carefully lift the microSD card holder.
6. Insert the microSD card into the
card holder.
NOTE :
Proper position of the microSD card — the card
connector (i.e., gold contacts) should be facing out as
shown.
7. Gently lower the microSD card holder until it snaps
into place.
SIM Card Holder
microSD Card Holder
Rubber Access Door
SIM Card Installation (Optional)
8. Insert the SIM card into the SIM holder.
NOTE :
The proper position of the SIM card—the card
connector (i.e., gold area) should be facing outward
with the beveled corner facing away.
9. Lower the SIM card holder.
10. Slide the SIM card holder down to lock into place.
11. Close the rubber access door.
12. Install the battery.
MC67
WITH ANDROID™ OS
QUICK START GUIDE
1 Scan/Action Button
2 Up/Down Button
3 Microphone
4 Power Button
5 I/O Connector
6 Keypad
7 Scan/Action Button
8 Touch Screen (with screen
protector)
9 Data Capture LED
10 Charging/Battery Status LED
11 WAN Radio Status LED
12 Phone Speaker
13 Handstrap
14 Battery
15 Battery Latch
16 Camera Flash
17 Camera
18 Exit Window (see Data Capture
Options)
19 Tether
20 Scan/Action Button
21 Action Button
22 Stylus
23 Speaker
DSD Keypad
Note 1: To reset the MC67, press and hold the Power button until the menu appears
and then select Reset.
Use this key to access application dependent
function keys shown on the keypad in blue.
Use this key to access the secondary
layer of characters.
Use this key to access the secondary layer of characters
1
2
BATTERY REMOVAL
1. Insert the battery, bottom first, into the battery compartment.
2. Press down on the battery until the battery latch snaps into
place.
3. Replace the handstrap.
3
AVOID EXTREME
WRIST ANGLES
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are
trademarks or registered trademarks of Motorola Trademark Holdings, LLC and
are used under license. Android is a trademark of Google Inc. All other
trademarks are the property of their respective owners.
© 2014 Motorola Solutions, Inc. All rights reserved.
MN000114A01 Rev. B — January 2014
Imaging
Camera Decode
Camera Photo
1. Ensure that an application is open and a text
field is in focus (text cursor in text field).
2. Point the MC67 at the bar code.
3. Press the Scan button.
4. In the image window align the red target
over the bar code. When the MC67 decodes
the bar code the Scan/Decode LED light
green and a beep sounds.
5. Release the Scan button.
1. Touch > Camera.
2. Point the MC67 at an object.
3. Touch the shutter button.
Motorola Solutions, Inc.
1301 E. Elgonquin Rd. Schaumburg, IL 60196-1078, U.S.A.
GPS Information
When using the GPS feature of the MC67:
BATTERY INSTALLATION
DATA CAPTURE OPTIONS
AVOID EXTREME WRIST ANGLES
1. Unlatch the handstrap.
2. Press the Power button until the menu appears.
3. Touch Battery Swap.
4. Wait for the red LED to turn off.
5. Slide the battery latch to the right. The battery ejects slightly.
6. Grasp the battery and lift from the MC67.
1. Ensure that an application is open and a text field is in focus (text
cursor in text field).
2. Point the exit window at the bar code.
3. Press and hold the Scan button.
4. The red laser aiming pattern turn on to assit in aiming. When
the MC67 decodes the bar code the Scan/Decode LED light green
and a beep sounds.
5. Release the Scan button.
Acquiring satellite signals may take a few minutes. It is best to be outside and
have a clear, unobstructed view of the sky.
Without a clear view, acquisition takes much longer and could result in the
MC67 being unable to compute the initial position quickly.
Obtain a satellite fix before moving.
Shutdown GPS application when not in use.
For more information see the MC67 User Guide and the MC67 Integator Guide available at:
http://supportcentral.motorolasolutions.com
  • Page 1 1
  • Page 2 2

Motorola MC67 Quick start guide

Category
Rechargeable batteries
Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI