Supermicro SUPER P6DLS User manual

Category
Motherboards
Type
User manual

This manual is also suitable for

®
SUPER
SUPER P6DLS
SUPER P6DLE
SUPER P6SLS
SUPER P6SLA
USER’S MANUAL
Revision 1.4
The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates.
SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF THE REPAIRING, REPLACING, OR
RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Unless you request and receive written permission from SUPERMICRO COMPUTER, you
may not copy any part of this document.
Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.
Copyright © 1998 by SUPERMICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America.
iii
Preface
About This Manual
This manual is written for system houses, PC technicians and
knowledgeable PC end users. It provides information for the instal-
lation and use of SUPER P6DLS/P6DLE/P6SLS/P6SLA
motherboard. SUPER P6DLS/P6DLE/P6SLS/P6SLA supports
Pentium II 233/266/300/333 MHz.
The Pentium II processor with the Dual Independent Bus Architec-
ture is housed in a new package technology called the Single Edge
Contact (S.E.C.) cartridge. This new cartridge package and its as-
sociated "Slot 1" infrastructure will provide the headroom for future
high-performance processors.
Manual Organization
Chapter 1, Introduction, describes the features, specifications and
performance of the SUPER P6DLS/P6DLE/P6SLS/P6SLA system
board, provides detailed information about the chipset, and offers
warranty information.
Refer to Chapter 2, Installation, for instructions on how to install the
Pentium II processor, the retention mechanism, and the heat sink
support. This chapter provides you with the instructions for han-
dling static-sensitive devices. Read this chapter when you want to
install or remove DIMM memory modules and to mount the system
board in the chassis. Also refer to this chapter to connect the floppy
and hard disk drives, IDE interfaces, parallel port, serial ports, as
well as the cables for the power supply, reset cable, Keylock/Power
LED, speaker and keyboard.
If you encounter any problem, please see Chapter 3, Troubleshoot-
ing, which describes troubleshooting procedures for video, memo-
ry, and the setup configuration stored in memory. Instructions are
also included on contacting a technical assistance support repre-
sentative and returning merchandise for service and the BBS# for
BIOS upgrades.
iv
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
Preface
Table of Contents
Preface
About This Manual ......................................................................................... iii
Manual Organization...................................................................................... iii
Quick Reference........................................................................................... viii
Chapter 1:
1-1 Overview............................................................................................... 1-1
SUPER P6DLS ............................................................................. 1-2
SUPER P6DLE ............................................................................. 1-3
SUPER P6SLA .............................................................................. 1-4
SUPER P6DLS Motherboard Layout........................................ 1-5
SUPER P6DLE Motherboard Layout........................................ 1-6
SUPER P6SLS Motherboard Layout ........................................ 1-7
SUPER P6SLA Motherboard Layout ........................................ 1-8
SUPER P6DLS Features............................................................ 1-9
SUPER P6DLE Features.......................................................... 1-11
SUPER P6SLS Features .......................................................... 1-13
SUPER P6SLA Features .......................................................... 1-15
1-2 PC Health Monitoring ...................................................................... 1-17
1-3 ACPI/PC 98 Features ...................................................................... 1-20
1-4 Chipset Overview.............................................................................. 1-22
1-5 Wake-on-LAN .................................................................................... 1-22
1-6 Power Supply .................................................................................... 1-22
1-7 National Semiconductor Super I/O................................................ 1-23
1-8 AIC 7880 SCSI Controller................................................................ 1-23
1-9 Warranty, Technical Support, and Service.................................. 1-24
Parts.............................................................................................. 1-24
BIOS .............................................................................................. 1-24
v
Labor............................................................................................. 1-25
Returns......................................................................................... 1-25
Chapter 2: Installation
2-1 Static-Sensitive Devices ................................................................... 2-1
Precautions ................................................................................... 2-1
Unpacking...................................................................................... 2-1
2-2 Pentium II Processor Installation................................................... 2-2
OEM Pentium II and Heat Sink Support.................................. 2-6
Removing the Pentium II Processor........................................ 2-7
2-3 Changing the CPU Speed ............................................................... 2-8
Turbo Function.............................................................................. 2-9
2-4 Mounting the Motherboard in the Chassis................................... 2-9
2-5 Connecting Cables............................................................................ 2-9
Power Supply Connector............................................................ 2-9
Infra-Red Connector ................................................................... 2-10
PW_ON Connector...................................................................... 2-11
Reset Connector ........................................................................ 2-11
Hard Drive LED .......................................................................... 2-12
Keylock/Power LED Cable Connector ................................... 2-12
Speaker Connector.................................................................... 2-13
SCSI LED..................................................................................... 2-13
Power Save State Select .......................................................... 2-13
ATX PS/2 Keyboard and Mouse Ports ................................... 2-14
Universal Serial Bus .................................................................. 2-14
ATX Serial Ports ......................................................................... 2-15
SMI................................................................................................. 2-15
CMOS Clear................................................................................. 2-16
External Battery ........................................................................... 2-16
Wake-on-LAN .............................................................................. 2-17
Fan Connectors.......................................................................... 2-17
vi
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
Table of Contents
vii
Chassis Intrusion Detector....................................................... 2-18
2-6 Installing/Removing the DIMM Modules...................................... 2-18
DIMM Module Installation.......................................................... 2-19
Removing DIMM Modules......................................................... 2-19
2-7 Connecting Parallel, FDD and HDD ............................................ 2-20
Parallel Port Connector ............................................................ 2-21
Floppy Connector ....................................................................... 2-22
IDE Interfaces ............................................................................. 2-23
SCSI Connectors......................................................................... 2-24
AGP Port....................................................................................... 2-26
Chapter 3: Troubleshooting
3-1 Troubleshooting Procedures ........................................................... 3-1
No Video ........................................................................................ 3-1
Troubleshooting Flowchart ........................................................ 3-2
Memory Error................................................................................. 3-3
Losing the System’s Setup Configuration.............................. 3-3
3-2 Technical Support Procedures........................................................ 3-4
3-3 Frequently Asked Questions............................................................. 3-4
3-4 Returning Merchandise for Service................................................. 3-7
viii
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
Quick Reference
Jumpers Function Page
JB1, JB2, JB3, JB4 CPU Speed Selection 2-8
JC1, JC2, JC3 External Bus Speed 2-8
JBT1 CMOS Clear 2-16
JP19 SMI 2-15
JP20 Power Save State
Select 2-13
JC4, JL2, JP17 Manufacturer Default 1-4
Connectors Function Page
J17 USB 2-14
J18 USB 2-14
J19 Printer Port 2-21
J20 COM 1 2-15
J21 COM 2 2-15
J32 ATX Power 2-9
J34 PS/2 KB and Mouse 2-14
JA1 UW SCSI 2-25
JA2 Ultra SCSI 2-24
JBT2 External Battery
Connector 2-16
JF1 IDE LED 2-12
Keylock 2-11
Speaker 2-12
JF2 IR Connector 2-10
PW_ON 2-10
Reset 2-11
JL1 Chassis Intrusion 2-18
JPA3 SCSI LED 2-13
JT1 CPU 1 Fan 2-17
JT2 CPU 2 Fan 2-17
JT3 Thermal/Overheat Fan 2-17
WOL Wake-on-LAN 2-17
1-1
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
SUPER P6DLS/P6DLE supports dual Pentium II 233/266/300/333
MHz processors. SUPER P6SLS/P6SLA supports single Pentium
II. They are based on Intel’s 440 LX chipset which enables Acceler-
ated Graphics Port (AGP), Wake-on-LAN, SDRAM, concurrent PCI
and Ultra DMA 33 MB/s burst data transfer rate.
All motherboards are ATX size and have 4 PCI slots, 3 ISA slots and
an AGP connector. SUPER P6DLS, P6DLE and P6SLS accommo-
date a total of 1 GB EDO or 512 MB SDRAM memory with 4 168-pin
DIMM sockets. SUPER P6SLA accommodates a total of 768 MB
EDO or 384 MB SDRAM memory with 3 168-pin DIMM sockets.
AGP reduces contention with the CPU and I/O devices by broaden-
ing the bandwidth of graphics to memory. It delivers a maximum of
532 MB/s 2x transfer mode which is quadruple the PCI speed!
Wake-on-LAN allows remote network management and configura-
tion of the PC, even in off-hours when the PC is turned off. This
reduces the complexity of managing the network.
Other features that maximize customer satisfaction and simplicity in
managing the computer are PC 98-ready and support for Advanced
Configuration and Power Interface (ACPI). With PC Health Monitor-
ing, you can protect your system from problems before they even
occur.
Included I/O on all motherboards are 2 EIDE ports, a floppy port, an
ECP/EPP parallel port, PS/2 mouse and PS/2 keyboard, 2 serial
ports, an infrared port and 2 USB ports. SUPER P6DLS and P6SLS
provide an on-board Adaptec 2940UW Ultra Wide SCSI controller
with fast data transfer rate of up to 40 MB/s.
1-2
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
SUPER P6DLS
Figure 1-1. SUPER P6DLS Motherboard Picture
1-3
Chapter 1: Introduction
SUPER P6DLE
Figure 1-2. SUPER P6DLE Motherboard Picture
1-4
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
SUPER P6SLA
Figure 1-3. SUPER P6SLA Motherboard Picture
1-5
Chapter 1: Introduction
Figure 1-4. SUPER P6DLS Motherboard Layout
®
J19
PRINTER
J21
COM2
J20
COM1
JJ14
J14
J13
J34
PS/2 KB
PS/2 MOUSE
J32
ATX POWER
J9
J11
J12
1
J10
JL2
1 JP19
PW_ON
RESET
IDE LED/KEYLOCK/SPEAKER
IR CON
JF2
Bank3
Bank2
Bank1
Bank0
JT3
+
-
BT2
BATTERY
IDE 1
IDE 2
1 1
J15 J16
FLOPPY
J22
1
JP20
1
JBT1
JBT2
1
1
1
JPA3
U27
BIOS
U29
ULTRA SCSI
JA2
JA1
UW SCSI
1
1
UA5
U14
UA7
1
WOL
J8
J2
J1
1
JT2
1
U9
1
JP17
U34
JA4
JB4
JB3
JB2
JB1
J17, J18
USB
JL1
JC3
JC2
JC1
JC4
S UPER P6DLS
SCSI
LED
—————Bus Speed–————
MHz JC1 JC2 JC3
50 ON ON ON
60 ON OFF OFF
66 OFF OFF OFF
75 OFF ON OFF
——–—–——————————
Chassis
Intrusion
Thermal
Control Fan
SCSI
Termination
AGP
JT1
CPU 2
FAN
CPU 1
FAN
Ext Battery
CMOS
Clear
——–—— Manufacturer Settings ————
JC4: OFF
JL1: OFF (normal)
ON (intrusion)
JL2: OFF
JP17: 2-3
JP19: 1-2 APIC SMI (default)
2-3 PIIX4 SMI
JP20: 1-2 PIIX4 CTL
2-3 Save PD State
JBT1: 1-2 (default)
2-3 CMOS Clear
To clear the CMOS completely,
disconnect the power source.
WOL: Wake-on-LAN
——–———————–———–——–——–—
CPU Core/
Bus Ratio
3.0
3.5
4.0
4.5
5.0
JB1
ON
OFF
ON
OFF
ON
JB2
OFF
OFF
ON
ON
OFF
JB3
ON
ON
OFF
OFF
OFF
JB4
ON
ON
ON
ON
ON
1-6
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
Figure 1-5. SUPER P6DLE Motherboard Layout
®
J19
PRINTER
J21
COM2
J20
COM1
JJ14
J14
J13
J34
PS/2 KB
PS/2 MOUSE
J32
ATX POWER
J9
J11
J12
1
J10
JL2
1 JP19
PW_ON
RESET
JF1
IDE LED/KEYLOCK/SPEAKER
IR CON
JF2
Bank3
Bank2
Bank1
Bank0
JT3
+
-
BT2
BATTERY
IDE 1
IDE 2
1 1
J15 J16
FLOPPY
J22
1
JP20
1
JBT1
JBT2
1
1
U27
BIOS
U29
U14
UA7
1
WOL
J2
J1
1
JT2
JT1
1
U9
1
JP17
U34
JB4
JB3
JB2
JB1
J17, J18
USB
JL1
JC3
JC2
JC1
JC4
S UPER P6DLE
—————Bus Speed–————
MHz JC1 JC2 JC3
50 ON ON ON
60 ON OFF OFF
66 OFF OFF OFF
75 OFF ON OFF
——–—–——————————
Chassis
Intrusion
Thermal
Control Fan
AGP
CPU 2
FAN
CPU 1
FAN
Ext Battery
CMOS
Clear
——–—— Manufacturer Settings ————
JC4: OFF
JL1: OFF (normal)
ON (intrusion)
JL2: OFF
JP17: 2-3
JP19: 1-2 APIC SMI (default)
2-3 PIIX4 SMI
JP20: 1-2 PIIX4 CTL
2-3 Save PD State
JBT1: 1-2 (default)
2-3 CMOS Clear
To clear the CMOS completely,
disconnect the power source.
WOL: Wake-on-LAN
——–———————–———–——–——–—
CPU Core/
Bus Ratio
3.0
3.5
4.0
4.5
5.0
JB1
ON
OFF
ON
OFF
ON
JB2
OFF
OFF
ON
ON
OFF
JB3
ON
ON
OFF
OFF
OFF
JB4
ON
ON
ON
ON
ON
1-7
Chapter 1: Introduction
Figure 1-6. SUPER P6SLS Motherboard Layout
®
J19
PRINTER
J21
COM2
J20
COM1
JJ14
J14
J13
J34
PS/2 KB
PS/2 MOUSE
J32
ATX POWER
J9
J11
J12
1
J10
JL2
1 JP19
PW_ON
RESET
JF1
IDE LED/KEYLOCK/SPEAKER
IR CON
JF2
Bank3
Bank2
Bank1
Bank0
JT3
+
-
BT2
BATTERY
IDE 1
IDE 2
1 1
J15 J16
FLOPPY
J22
1
JP20
1
JBT1
JBT2
1
1
1
JPA3
U27
BIOS
U29
ULTRA SCSI
JA2
JA1
UW SCSI
1
1
UA5
U14
UA7
1
WOL
J8
J2
J1
1
JT2
JT1
1
U9
1
JP17
U34
JA4
JB4
JB3
JB2
JB1
J17, J18
USB
JL1
JC3
JC2
JC1
JC4
S UPER P6SLS
SCSI
LED
—————Bus Speed–————
MHz JC1 JC2 JC3
50 ON ON ON
60 ON OFF OFF
66 OFF OFF OFF
75 OFF ON OFF
——–—–——————————
Chassis
Intrusion
Thermal
Control Fan
SCSI
Termination
AGP
J2 is for
termination
CPU 2
FAN
CPU 1
FAN
Ext Battery
CMOS
Clear
——–—— Manufacturer Settings ————
JC4: OFF
JL1: OFF (normal)
ON (intrusion)
JL2: OFF
JP17: 2-3
JP19: 1-2 APIC SMI
2-3 PIIX4 SMI (default)
JP20: 1-2 PIIX4 CTL
2-3 Save PD State
JBT1: 1-2 (default)
2-3 CMOS Clear
To clear the CMOS completely,
disconnect the power source.
WOL: Wake-on-LAN
——–———————–———–——–——–—
CPU Core/
Bus Ratio
3.0
3.5
4.0
4.5
5.0
JB1
ON
OFF
ON
OFF
ON
JB2
OFF
OFF
ON
ON
OFF
JB3
ON
ON
OFF
OFF
OFF
JB4
ON
ON
ON
ON
ON
1-8
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
Figure 1-7. SUPER P6SLA Motherboard Layout
JJ14
J14
J13
U34
J19
PRINTER
J21
COM2
J20
COM1
J34
PS/2 KB
PS/2 MOUSE
J32
ATX POWER
J1
J17, J18
USB
PW_ON RESET
JF1
IR CON
JF2
IDE LED/KEYLOCK/SPEAKER
Chassis Intrusion
JL1
U29
BIOS
1
WOL
J9
J11
J12
1
J10
JL2
J8
AGP
JT2
JT3
Overheat
Fan
+
-
BATTERY
BT2
JP20
1
J15 J16
1
1
J22
1
FLOPPY
IDE 1
IDE 2
JBT1
JBT2
Ext Battery
1
1
CMOS Clear
JC3
JC2
JC1
JC4
JB3
JB4
JB2
JB1
U27
U14
Bank1
Bank2
Bank0
1
CPU
FAN
JT1
U9
——–—— Manufacturer Settings ————
JC4: OFF
JL1: OFF (normal)
ON (intrusion)
JL2: OFF
JP20: 1-2 PIIX4 CTL
2-3 Save PD State
JBT1: 1-2 (default)
2-3 CMOS Clear
To clear the CMOS completely,
disconnect the power source.
WOL: Wake-on-LAN
JT1: CPU fan1
JT2: CPU fan2
JT3: Overheat fan
——–———————–———–——–——–—
—————Bus Speed–————
MHz JC1 JC2 JC3
50 ON ON ON
60 ON OFF OFF
66 OFF OFF OFF
75 OFF ON OFF
——–—–——————————
S UPER P6SLA
®
CPU Core/
Bus Ratio
3.0
3.5
4.0
4.5
5.0
JB1
ON
OFF
ON
OFF
ON
JB2
OFF
OFF
ON
ON
OFF
JB3
ON
ON
OFF
OFF
OFF
JB4
ON
ON
ON
ON
ON
1-9
Chapter 1: Introduction
SUPER P6DLS Features
The following list covers the general features of SUPER P6DLS:
CPU
Dual Pentium II processor 233/266/300/333 MHz
Memory
1 GB EDO or 512 MB SDRAM
Error Checking and Correction and Parity Checking support
Chipset
Intel 440LX
Expansion Slots
4 PCI slots
3 ISA slots
1 AGP slot
BIOS
AMI
®
Flash WINBIOS with boot block support
DMI 2.0, Plug and Play (PnP)
PC Health Monitoring (LM78)
Seven on-board voltage monitors for 2 CPU cores, +3.3V, ±5V,
and ±12V
Three-fan status monitors with firmware/software control on/off
CPU/chassis temperature monitor and control
CPU fan auto-off in sleep mode
CPU overheat control and alarm
Chassis intrusion detection
System resource alert
Hardware BIOS virus protection
Switching voltage regulator for the CPU core
SUPERMICRO SUPER Doctor and Intel
®
LANDesk
®
Client
Manager (LDCM) support
1-10
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
ACPI/PC 98 Features
Microsoft
®
OnNow
Slow blinking LED for suspend-state indicator
BIOS support for USB keyboard
Real time clock wake-up alarm
Main switch override mechanism
External modem ring-on if system is in SoftOff state
On-Board I/O
68-pin 16-bit Ultra-Wide SCSI connector and
50-pin 8-bit Ultra SCSI connector
2 EIDE Bus Master interfaces support Ultra DMA/33 and PIO
Mode 4
1 floppy interface
2 Fast UART 16550 serial ports
EPP (Enhanced Parallel Port) and ECP (Extended Capabilities
Port) parallel port
PS/2 mouse and PS/2 keyboard
Infrared port
2 USB ports
Dimensions
ATX (12" x 10.85")
CD Utilities
Intel LANDesk Client Manager for Windows NT
®
and Windows
95
®
(optional)
PIIX4 Upgrade Utility for Windows 95
BIOS Flash Upgrade Utility
DMI Browser for Windows 95
DMI Wizard
Super Doctor Utility ver 1.20b
1-11
Chapter 1: Introduction
SUPER P6DLE Features
The following list covers the general features of SUPER P6DLE:
CPU
Dual Pentium II processor 233/266/300/333 MHz
Memory
1 GB EDO or 512 MB SDRAM
Error Checking and Correction and Parity Checking support
Chipset
Intel 440LX
Expansion Slots
4 PCI slots
3 ISA slots
1 AGP slot
BIOS
AMI
®
Flash WINBIOS with boot block support
DMI 2.0, Plug and Play (PnP)
PC Health Monitoring (LM78)
Seven on-board voltage monitors for 2 CPU cores, +3.3V, ±5V,
and ±12V
Three-fan status monitors with firmware/software control on/off
CPU/chassis temperature monitor and control
CPU fan auto-off in sleep mode
CPU overheat control and alarm
Chassis intrusion detection
System resource alert
Hardware BIOS virus protection
Switching voltage regulator for the CPU core
SUPERMICRO SUPER Doctor and Intel LANDesk Client Man-
ager (LDCM) support
1-12
SUPER P6DLS/P6DLE/P6SLS/P6SLA User’s Manual
ACPI/PC 98 Features
Microsoft OnNow
Slow blinking LED for suspend-state indicator
BIOS support for USB keyboard
Real time clock wake-up alarm
Main switch override mechanism
External modem ring-on if system is in SoftOff state
On-Board I/O
2 EIDE Bus Master interfaces support Ultra DMA/33 and PIO
Mode 4
1 floppy interface
2 Fast UART 16550 serial ports
EPP (Enhanced Parallel Port) and ECP (Extended Capabilities
Port) parallel port
PS/2 mouse and PS/2 keyboard
Infrared port
2 USB ports
Dimensions
ATX (12" x 10.85")
CD Utilities
Intel LANDesk Client Manager for Windows NT and Windows 95
(optional)
PIIX4 Upgrade Utility for Windows 95
BIOS Flash Upgrade Utility
DMI Browser for Windows 95
DMI Wizard
Super Doctor Utility ver 1.20b
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Supermicro SUPER P6DLS User manual

Category
Motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI