Xantech 172-78 is an infrared remote control extension system that allows you to control your satellite receiver, cable box, or VCR from a second room by sharing the coaxial cable connecting your video equipment to this second room’s TV. The kit includes an IR receiver, injector, coupler, dual IR emitter, and power supply. The IR receiver is placed in the remote room to receive IR signals from the handheld remote controller. The injector is located in the remote room and injects the remote control signal into the room-to-room coaxial cable.
Xantech 172-78 is an infrared remote control extension system that allows you to control your satellite receiver, cable box, or VCR from a second room by sharing the coaxial cable connecting your video equipment to this second room’s TV. The kit includes an IR receiver, injector, coupler, dual IR emitter, and power supply. The IR receiver is placed in the remote room to receive IR signals from the handheld remote controller. The injector is located in the remote room and injects the remote control signal into the room-to-room coaxial cable.
IR Receivers
1
INSTALLATION INSTRUCTIONS
172-78
XTRA LINK
®
2
REMOTE CONTROL EXTENSION SYSTEM
The Xtra Link 2 system provides full remote control operation of a satellite receiver, cable box or VCR from
a second room by sharing the coaxial cable connecting your video equipment to this second room’s TV.
The 172-78 Xtra Link consists of the following supplied parts:
1. One 291-10 Infrared Receiver. It is placed at the
remote room location to receive IR signals from the
handheld remote controller.
2. One INJ77 Injector. This unit, located in the Remote
Room, injects the remote control signal into the room-
to-room coaxial cable (along with the TV signal) and
passes it to the CPL77 Coupler in the Main room. It
also provides quick connection of the 291-00 IR Re-
ceiver and 781C-78 Power Supply cables.
3. One CPL77 Coupler. Located in the Main Room, this
Coupler extracts the remote control signal from the
coaxial cable and passes it to the emitters that control
your source equipment. In addition, the CPL77 con-
tains a 2-way RF splitter so that the TV signal can be
fed to a local TV.
4. One 284M Dual IR Emitter. The emitters on this
device allow control of two infrared remote controlled
audio/video components.
5. One 781C-78 Power Supply. This plugs into an
unswitched 220-240 VAC outlet to provide power to
the 291-00 IR Receiver.
CONNECTIONS
The Xtra Link system uses the coaxial cable that
carries the TV RF signal from the source equip-
ment in the main room to the remote room, to
send the IR control signals back to the source
equipment. The coaxial cable may be up to one
mile in length.
If you already have a coaxial cable connecting
your video equipment with a remote room, your
current hookup should be similar to Fig. 1. If it
isn't, run a single length of RG59 or preferably
RG6 cable from the Main Room to the Remote
Room.
NOTE: If RF amplifier(s) are used anywhere in
the line of coaxial cable between the CPL77
Coupler and the INJ77 Injector, you must use a
Xantech BYPASS77 KIT to route the IR com-
mands around the amplifier(s).
781C-78
Power Supply
284M
Dual Mouse Emitter
Front View Side View
IR RECEIVER
INJ77 INJECTOR
ANT INPUT
+12 V
REMOTE TV
EMITTER
LOCAL TV
CPL77 COUPLER
SAT/VCR
TO TV
SIDE VIEW
291-00 IR Receiver
SIDE VIEW
172-78 Xtra Link 2 System Parts
Fig. 1 Basic System Without Xtra Link
Satellite Dish
REMOTE ROOM
RF IN
MAIN ROOM
Room-to-Room Coaxial Cable
RF INOUT TO TV
SATELLITE RECEIVER
(Back Panel)
RF IN
VCR
(Back Panel)
OUT TO TV
Coaxial Cable
1ST
TV
RF SPLITTER
2-Way
Coaxial Cable
Coaxial Cable
2ND
TV
RF IN
2
172-78
When using more than one Xtra Link for more rooms, be sure the RF splitters you use are DC passing types,
such as Xantech part number 04027500 (2-way). Refer to Fig. 3.
INSTALLING THE 291-00 IR RECEIVER
Insert the cable mini plug attached to the 291-00 into the jack marked "IR RECEIVER" on the INJ77 Injector.
Refer to Fig. 2.
Plug the 781C-78 Power Supply cord into the jack marked "+12 V" on the INJ77 Injector. Plug the 781C-
78 into a 220 VAC unswitched outlet after you have made all other connections.
Position the 291-00 IR Receiver so that the infrared beam from the handheld remote control has a direct
view to the front of the unit (within 20 feet).
INSTALLING THE INJ77 INJECTOR
Insert the "TO TV" plug on the back of the INJ77 Injector into "RF IN" on the TV in the Remote Room.
Connect the room-to-room cable to "ANT INPUT" on the INJ77 Injector.
Satellite Dish
TV SIGNAL PATH
IR REMOTE CONTROL PATH
Hand Held
Remote
REMOTE
ROOM
RF IN
284M
Dual Mouse
Emitter Assembly
(Included)
MAIN ROOM
CPL77 COUPLER
(included)
Room-to-Room Coaxial Cable
(not included)
Coaxial Cable
(Not included)
Place emitters on
the IR sensor
window on front
panel of each
controlled unit.
Emitter
RF INOUT TO TV
SATELLITE
RECEIVER
(Back Panel)
RF IN
VCR
(Back Panel)
Emitter
IR Sensor Windows
(Front Panel)
Coaxial Cable
(not included)
To 220 V AC
(unswitched)
INJ77 INJECTOR
(included)
291-00
IR RECEIVER
(included)
2ND
TV
781C-78
Power Supply (included)
1ST
TV
RF IN
Coaxial Cable
(not included)
REMOTE
TV
EMITTER
LOCAL TV
CPL77 COUPLER
SAT/VCR
Front View Side View
OUT TO TV
IR RECEIVER
INJ77 INJECTOR
ANT INPUT
+12 V
TO TV
Front View
Side View
Fig. 2 Basic Xtra Link Hookup
INSTALLING THE CPL77 COUPLER
Insert the "SAT/VCR" plug on the back of the CPL77 Coupler into "OUT TO TV" on VCR in the Main Room.
Connect the room-to-room cable to "REMOTE/TV" on the CPL77 Coupler.
Make the remaining connections from the CPL77 Coupler to the TV, the VCR to the satellite receiver, etc.,
as shown in Fig. 2.
IR Receivers
3
172-78
INSTALLING THE XTRA LINK 284M DUAL IR EMITTER
Plug the 284M Dual IR Emitter into the jack marked "EMITTER" on the CPL77 Coupler in the Main Room.
The 284-10 emitters should be installed directly to the infrared sensor "window" on the front panel of the
satellite receiver, VCR, cable box, etc. Simply remove the paper backing exposing the adhesive surface
of each emitter and apply them to the center of the sensor window.
NOTE: Although the 284M appears dark to the eye, it is transparent to infrared. Positioning the 284M
directly over the infrared window(s) of the component(s) will not block direct IR control from a handheld
remote.
OPERATION
To use the Xtra Link Remote Control Extension System, simply point your handheld remote control(s) at
the 291-00 IR Receiver and press the desired button. A red LED on the front of the 291-00 will indicate the
reception of your infrared command.
NOTE: The maximum usable distance between your IR remote and the 291-00 Receiver will vary for each
remote and might be shorter than when directly used in the room containing the satellite receiver or other
IR controlled devices.
The 172-78 system
may be left on continuously as it does not affect the normal operation of the remote
controlled device(s) and consumes very little energy.
TO TV
Satellite Dish
TV SIGNAL PATH
IR REMOTE CONTROL PATH
Hand Held
Remote
REMOTE
ROOM
RF
IN
284M
Dual Mouse
Emitter Assembly
(included)
MAIN ROOM
CPL77 COUPLER
(included)
Room-to-Room Coaxial Cable
(not included)
Coaxial Cable
(not included)
Place emitters on
the IR sensor
window on front
panel of each
controlled unit.
Emitter
RF INOUT TO TV
SATELLITE
RECEIVER
(Back Panel)
RF IN
VCR
(Back Panel)
Emitter
IR Sensor Windows
(Front Panel)
Coaxial Cable
(not included)
INJ77 INJECTOR
(included)
291-00
IR RECEIVER
(included)
2ND
TV
1ST
TV
RF IN
Coaxial Cable
(not included)
REMOTE
TV
EMITTER
LOCAL TV
CPL77 COUPLER
SAT/VCR
Front View Side View
OUT TO TV
IR RECEIVER
INJ77 INJECTOR
ANT INPUT
+12 V
Front View Side View
RF SPLITTER
2-Way DC Passing
(Xantech # 04027500
not Included)
Room-to-Room
Coaxial Cable
(not included)
TO TV
REMOTE
ROOM
RF
IN
To 220 V AC
(unswitched)
3RD
TV
IR RECEIVER
INJ77 INJECTOR
ANT INPUT
+12 V
Front View Side View
Coaxial Cable
(not included)
Hand Held
Remote
781C78
Power Supply (included)
291-00
IR RECEIVER
(included)
781C78
Power Supply (included)
To 220 V AC
(unswitched)
INJ77 INJECTOR
(included)
Fig. 3 Advanced Multiroom Hookup
4
HOW TO AVOID PROBLEMS
In rare cases, the 291-00 IR Receiver may have to be moved to a different location if the unit is picking up
interference. This interference may, in severe cases, prevent the system from working.
Common examples of interference are:
• RF radiation from the TV set on which the 291-00 IR Receiver may have been placed.
• Direct or reflected sunlight.
• Fluorescent, Compact Fluorescent, Neon, Neon Art, Halogen lights or light dimmers.
• Infrared security systems.
You can confirm the source of the interference by temporarily turning off the remote room TV set, isolating
the 291-00 Receiver from all sunlight and turning off all lights, light dimmers and Infrared security systems.
Then check to see if the 291-00 operates the satellite receiver or other components.
If the 291-00 still does not work, reposition the 284M Emitter(s). It may not be located directly over the
component’s infrared receiving "window". Consult the owner's manual of the unit or the manufacturer for
the exact location of the infrared "window".
IMPORTANT: For installations involving more than two remote rooms, use the services of a competent
professional audio/video installer experienced in infrared remote control systems.
172-78
1/17/01
Rev.A
-
1
-
2
-
3
-
4
Xantech 172-78 User manual
- Type
- User manual
- This manual is also suitable for
Xantech 172-78 is an infrared remote control extension system that allows you to control your satellite receiver, cable box, or VCR from a second room by sharing the coaxial cable connecting your video equipment to this second room’s TV. The kit includes an IR receiver, injector, coupler, dual IR emitter, and power supply. The IR receiver is placed in the remote room to receive IR signals from the handheld remote controller. The injector is located in the remote room and injects the remote control signal into the room-to-room coaxial cable.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
C2G 37015 Owner's manual
-
PAC IR-X/HOME User manual
-
EDOBE XDOM IR LINK C Owner's manual
-
Nortek Contol Fan 2171-4 User manual
-
Channel Plus SVS-88 User manual
-
ONKYO TX-SV525R User manual
-
Vaux Electronics Aris 700 User manual
-
Mitsubishi WD-52525 User manual
-
Logic 3 RAT 1 User manual
-
