ZiLOG Z16FMC3 User manual

ZiLOG
Brand
ZiLOG
Model
Z16FMC3
Type
User manual

This manual is also suitable for

ZiLOG Z16FMC3 is a versatile Flash microcontroller based on Zilog’s advanced ZNEO 16-bit CPU core. Optimized for motor control applications, this device supports the control of single- and multi-phase variable-speed motors. Target applications are large appliances, small appliances and HVAC.

Key features include:

  • 16-bit optimized single-cycle CISC core
  • Up to 128 KB of in-circuit programmable Flash memory
  • 12-Channel, 10-bit ADC with a 2.1μs conversion time
  • Highly integrated digital/analog peripherals
    • Operational Amplifier
    • Analog Comparator
    • Internal Precision Oscillator

ZiLOG Z16FMC3 is a versatile Flash microcontroller based on Zilog’s advanced ZNEO 16-bit CPU core. Optimized for motor control applications, this device supports the control of single- and multi-phase variable-speed motors. Target applications are large appliances, small appliances and HVAC.

Key features include:

  • 16-bit optimized single-cycle CISC core
  • Up to 128 KB of in-circuit programmable Flash memory
  • 12-Channel, 10-bit ADC with a 2.1μs conversion time
  • Highly integrated digital/analog peripherals
    • Operational Amplifier
    • Analog Comparator
    • Internal Precision Oscillator
Copyright ©2011 Zilog
®
, Inc. All rights reserved.
www.zilog.com
User Manual
Z16FMC
™
Series Motor
Control Development Kit
ZNEO
®
Motor Control Family
UM023402-0811
Foreword UM023402-0811
Z16FMC™ Series Motor Control Development Kit
User Manual
ii
DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF
THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for
use provided in the labeling can be reasonably expected to result in a significant injury to the user. A criti-
cal component is any component in a life support device or system whose failure to perform can be reason-
ably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
Document Disclaimer
©2011 Zilog, Inc. All rights reserved. Information in this publication concerning the devices, applications,
or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES
NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE
INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED
IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED
HEREIN OR OTHERWISE. The information contained within this document has been verified according
to the general principles of electrical and mechanical engineering.
Z8, Z8 Encore!, Z8 Encore! XP, Z8 Encore! MC, eZ80, ZNEO and Z16FMC are trademarks or registered
trademarks of Zilog, Inc. All other product or service names are the property of their respective owners.
Warning:
UM023402-0811 Revision History
Z16FMC™ Series Motor Control Development Kit
User Manual
iii
Revision History
Each instance in the Revision History table below reflects a change to this document from
its previous version. For more details, click the appropriate links in the table.
Date
Revision
Level Description Page
Aug
2011
02 Updated schematic diagram in Figure 7 to Rev C per CR#13165. 13
Nov
2010
01 Original issue. All
Revision History UM023402-0811
iv
Z16FMC™ Series Motor Control Development Kit
User Manual
UM023402-0811 Table of Contents
Z16FMC™ Series Motor Control Development Kit
User Manual
v
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Development Kit Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MC MDS Module Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Module Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3-Phase Motor Control Application Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Application Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ZDS II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting and Developer Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Recheck Procedures with the Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Zilog Customer Support Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Linix Motor Wiring Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table of Contents UM023402-0811
vi
Z16FMC™ Series Motor Control Development Kit
User Manual
UM023402-0811 Introduction
Z16FMC™ Series Motor Control Development Kit
User Manual
1
Introduction
Zilog’s Z16FMC
™
Series Motor Control Development Kit aids in the develoment of
motor control applications using Zilog’s 64-LQFP Z16FMC Motor Control MCU and pro-
vides an application-specific platform for creating a design based on the Z16FMC series
microcontroller. The development kit features a Motor Control Modular Development
System (MC MDS) module mounted on a 3-Phase Motor Control Application Board. A
24 VDC, 3200 RPM 3-phase motor is included with the kit.
Kit Features
The key features of the Z16FMC
™
Series Motor Control Development Kit include:
•
MC MDS Module
•
3-Phase Motor Control Application Board
•
USB Smart Cable with opto-isolator
•
3-phase 24 VDC, 30 W, 3200 RPM motor with spade connectors and Internal Hall Sen-
sors (powered by external adjustable 24 VDC supply, not included in kit)
•
Universal 5 VDC power supply
•
Motor Control Software and Documentation CD-ROM
For Z16FMC
™
Series Motor Control Development Kit installation and setup instructions,
refer to the Z16FMC
™
Series Motor Control Development Kit Quick Start Guide
(QS0079).
Development Kit Block Diagram
Figure 1 displays a block diagram of the Z16FMC
™
Series Motor Control Development
Kit.
MC MDS Module Description UM023402-0811
2
Z16FMC™ Series Motor Control Development Kit
User Manual
MC MDS Module Description
The MC MDS Module features the Z16FMC MCU, as shown in Figure 2. It provides cir-
cuitry that interfaces the chip to an external development PC running the Zilog Developer
Studio II (ZDS II) Integrated Development Environment (IDE), and to the 3-Phase Motor
Control Application Board.
Figure 1. Z16FMC Series Motor Control Development Kit
3.3V to
12V
Converter
Gate Drivers
and
Sensors
Power
MOSFETs
Phase B
Phase A
+24V, 1A
Analog Signals
AH
AL
BH
BL
CH
CL
PWM
Debug
Motor Control
MDS Module
Motor Control
Application Board
5 VDC
GND
Phase C
3.3V Power
Regulator
Z16FMC MCU
Speed
UM023402-0811 MC MDS Module Description
Z16FMC™ Series Motor Control Development Kit
User Manual
3
Module Features
The features of the MC MDS Module include:
•
A Z16FMC device operating at 20 MHz with 128 KB of internal Flash memory and
4 KB of internal register SRAM
•
20 MHz ceramic resonator Y1
•
Two SPDT switches, S2 and S3(labeled DIRECTION and STOP/RUN, respectively)
•
One 5 K potentiometer, R7
•
Green LED D1 (illuminates when 3.3 VDC is applied to the board)
•
Three general-purpose LEDs D2, D3 and D4
•
RS-232 port
•
6-pin DBG interface
•
Two 60-pin headers for connecting to the 3-Phase Motor Control Application Board
(JP1 and JP2; JP1 used for physical mounting only)
Figure 2. MC MDS Module
MC MDS Module Description UM023402-0811
4
Z16FMC™ Series Motor Control Development Kit
User Manual
Z16FMC MCU
The Z16FMC Series Flash microcontrollers are based on Zilog’s advanced ZNEO 16-bit
CPU core. Optimized for motor control applications, these devices support the control of
single- and multi-phase variable-speed motors. Target applications are large appliances,
small appliances and HVAC.
The Z16FMC
™
Series Motor Control Development Kit consists of circuitry to support and
present all the features of the Z16FMC MCU. The key features of the Z16FMC MCU
include:
•
16-bit optimized single-cycle CISC core
•
Up to 128 KB of in-circuit programmable Flash memory
•
Highly integrated digital/analog peripherals
– Operational Amplifier
– Analog Comparator
– Internal Precision Oscillator
– 4-Channel DMA Controller
– 12-bit PWM module with three complementary pairs or six independent PWM
outputs
•
Flexible communication interface including a 9-bit UART with LIN and IrDA, I
2
C,
and ESPI
•
12-Channel, 10-bit ADC with a 2.1μs conversion time
For more information about the Z16FMC MCU, refer to the Z16FMC Series
Motor Con-
trol Product Specification (PS0287) or the Z16FMC Series Flash Microcontroller Product
Brief (PB0229) available from the kit’s CD-ROM and also available for download at
www.zilog.com
.
Connector JP2
Connector JP2 is a 60-pin header that connects I/O from the Z16FMC MCU to the 3-Phase
Motor Control Application Board. Figure 3 displays the pin layout. Table 1, which fol-
lows, identifies the signals and their functions.
UM023402-0811 MC MDS Module Description
Z16FMC™ Series Motor Control Development Kit
User Manual
5
Figure 3. MC MDS Board Connector JP2
Table 1. Connector JP2 Signal Descriptions
Signal Pins
Direction
(with respect
to MCU) Description
ANA0 1 I Analog input to the ADC.
ANA1 2 I Analog input to the ADC.
ANA2 3 I Analog input to the ADC.
ANA6 4 I Analog input to the ADC.
ANA7 5 I Analog input to the ADC.
ANA3 6 I Analog input to the ADC.
ANA4 7 I Analog input to the ADC.
ANA5 8 I Analog input to the ADC.
VCC_3v3 9 n/a 3.3 VDC Power.
GND 10 n/a Ground.
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
ANA7
PD5_TXD1
PC1_TOUT
ANA3
PC3_SCK
PWMH1
PC4_MOSI
GND
ANA5
PA7_SDA
PD3
PC6_T2IN_PWMH0
GND
VCC_3v3
PC7_T2OUT_PWML0
ANA4
GND
PWML2
PA2
PWMH2
PC2_nSS
ANA0
PA6_SCL
PD6_nCTS1
PA4_RXD0
PC0_T1IN
PWML1
ANA1
PC5_MISO
PA3_nCTS0
ANA2
PD4_RXD1
-RESET
VCC_3v3
VCC_3v3
GND
ANA6
PA5_TXD0
GND
PH3_ANA11
GND
PA0
PA1 PF7
PG3
PWMH2 PWML2
PWMH1
PWML1
TXD1
RXD1
nCTS1
-RESET
DE1
PF7
PG3
JP2
HDR/PIN 2x30
JP2
HDR/PIN 2x30
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
20
21
21
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
42
42
43
43
44
44
45
45
46
46
47
47
48
48
49
49
50
50
51
51
52
52
53
53
54
54
55
55
56
56
57
57
58
58
59
59
60
60
MC MDS Module Description UM023402-0811
6
Z16FMC™ Series Motor Control Development Kit
User Manual
PC4_MOSI 11 I/O Port C[4]; used for general purpose I/O or MOSI.
PC5_MISO 12 I/O Port C[5]; used for general purpose I/O or MISO.
PWMH2 13 O PWM High Output.
PWML2 14 O PWM Low Output.
PC3_SCK 15 I/O Port C[3]; used for general purpose I/O or SCK.
PC2_nSS 16 I/O Port C[2]; used for general purpose I/O or nSS.
PWMH1 17 O PWM High Output.
PC6_T2IN_PWMH0 18 I/O Port C[6]; used for general purpose I/O or T2IN or
PWMH0.
GND 19 n/a Ground.
PC7_TOUT_PWML0 20 I/O Port C[7]; used for general purpose I/O or TOUT or
PWML0.
PWML1 21 O PWM Low Output.
PA2 22 I/O Port A[2]; used for general purpose I/O.
PC1_TOUT 23 I/O Port C[1]; used for general purpose I/O or T1OUT.
PD6_nCTS1 24 I/O Port D[6]; used for general purpose I/O or nCTS1.
PD3 25 I/O Port D[3]; used for general purpose I/O.
PD4_RXD1 26 I/O Port D[4]; used for general purpose I/O or RXD1.
PD5_TXD1 27 I/O Port D[5]; used for general purpose I/O or TXD1.
PC0_T1IN 28 I/O Port C[0]; used for general purpose I/O or T1IN.
PA0 29 I/O Port A[0]; used for general purpose I/O.
GND 30 n/a Ground.
PA1 31 I/O Port A[1]; used for general purpose I/O.
PF7 32 I/O Port F[7]; used for general purpose I/O.
PA3_nCTS0 33 I/O Port A[3]; used for general purpose I/O or nCTS0.
PG3 34 I/O Port G[3]; used for general purpose I/O.
PA4_RXD0 35 I/O Port A[4]; used for general purpose I/O or RXD0.
PA5_TXD0 36 I/O Port A[5]; used for general purpose I/O or TXD0.
NC 37 n/a No Connect.
NC 38 n/a No Connect.
GND 39 n/a Ground.
NC 40 n/a No Connect.
Table 1. Connector JP2 Signal Descriptions (Continued)
Signal Pins
Direction
(with respect
to MCU) Description
UM023402-0811 MC MDS Module Description
Z16FMC™ Series Motor Control Development Kit
User Manual
7
NC 41 n/a No Connect.
NC 42 n/a No Connect.
NC 43 n/a No Connect.
NC 44 n/a No Connect.
PA6_SCL 45 I/O Port A[6]; used for general purpose I/O or SCL.
GND 46 n/a Ground.
PA7_SDA 47 I/O Port A[7]; used for general purpose I/O or SDA.
GND 48 n/a Ground.
NC 49 n/a No Connect.
NC 50 n/a No Connect.
NC 51 n/a No Connect.
NC 52 n/a No Connect.
RESET 53 n/a SET is active Low.
PH3_ANA11 54 I/O Port H[3]; used for general purpose I/O or ANA11.
VCC_3v3 55 n/a 3.3 VDC Power.
GND 56 n/a Ground.
NC 57 n/a No Connect.
NC 58 n/a No Connect.
VCC_3v3 59 n/a 3.3 VDC Power.
NC 60 n/a No Connect.
Table 1. Connector JP2 Signal Descriptions (Continued)
Signal Pins
Direction
(with respect
to MCU) Description
MC MDS Module Description UM023402-0811
8
Z16FMC™ Series Motor Control Development Kit
User Manual
Connector JP3
Connector JP3 is a 26-pin header that allows access to the analog signals. Figure 4 dis-
plays the pin layout. Table 2, which follows, identifies the signals and their functions.
Figure 4. MC MDS Board Connector JP3
Table 2. Connector JP3 Signal Descriptions
Signal Pins
Direction
(with respect
to MCU) Description
V
REF
1 Input ADC Reference Voltage.
ANA11 3 Input Input to ADC.
ANA10 5 Input Input to ADC.
ANA2 7 Input Input to ADC.
ANA3 9 Input Input to ADC.
ANA7 11 Input Input to ADC.
ANA6 13 Input Input to ADC.
ANA5 15 Input Input to ADC.
ANA4 17 Input Input to ADC.
ANA1 19 Input Input to ADC.
ANA0 21 Input Input to ADC.
ANA8 23 Input Input to ADC.
ANA9 25 Input Input to ADC.
GND 2, 4, 6, 8, 10, 12, 14, 16,
18, 20, 22, 24, 26
n/a Ground.
VREF
PB5_ANA5
PB7_ANA7
PB3_ANA3
PB0_ANA0
PB6_ANA6
PB2_ANA2
PH0_ANA8
PB1_ANA1
PB4_ANA4
PH1_ANA9
PH2_ANA10
PH3_ANA11
JP3
HDR/PIN 2x13
JP3
HDR/PIN 2x13
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
20
21
21
22
22
23
23
24
24
25
25
26
26
UM023402-0811 MC MDS Module Description
Z16FMC™ Series Motor Control Development Kit
User Manual
9
Connector J1
Connector J1 is a 16-pin header that allows access to all Port E signals. Figure 5 displays
the pin layout. Table 3, which follows, identifies the Port E signals and their functions.
Jumper and Switch Settings
The MDS module has two SPDT switches (S2 and S3) and a 5 K potentiometer (R7) used
by the development kit’s preloaded demonstration software to perform the following func-
tions:
S2, DIRECTION. Used to change the 3-phase motor spin direction.
S3, STOP/RUN. Used to turn the 3-phase motor ON and OFF.
R7, SPEED. Used to adjust the 3-phase motor RPM.
Figure 5. MC MDS Board Connector JP1
Table 3. Connector JP1 Signal Descriptions
Signal Pins
Direction
(with respect
to MCU) Description
PE0 1 I/O Port E[0].
PE1 3 I/O Port E[1].
PE2 5 I/O Port E[2].
PE3 7 I/O Port E[3].
PE4 9 I/O Port E[4].
PE5 11 I/O Port E[5].
PE6 13 I/O Port E[6].
PE7 15 I/O Port E[7].
GND 2, 4, 6, 8, 10, 12, 14, 16 n/a GND.
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE7
J1
HDR/PIN 2x8
J1
HDR/PIN 2x8
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
3-Phase Motor Control Application Board UM023402-0811
10
Z16FMC™ Series Motor Control Development Kit
User Manual
Physical Dimensions
The footprint of the MC MDS module PCB is 9.5 cm x 9.30 cm. When mounted on the 3-
Phase Motor Control Application Board, the overall development kit height is 4.0 cm.
3-Phase Motor Control Application Board
The 3-Phase Motor Control Application Board provides circuitry that drives the 3-phase
24 VDC, 3200 RPM motor included with the development kit (see Figure 6). It provides
fused 24 VDC inputs for supplying external adjustable workbench power to run the motor,
and interfaces the motor to the Z16FMC MCU mounted on the MC MDS module.
Application Board Features
The features of 3-Phase Motor Control Application Board include:
•
Three spade lug connectors, one for each motor phase
•
Dual power MOSFETs for each motor phase
Figure 6. 3-Phase Motor Control Application Board
UM023402-0811 ZDS II
Z16FMC™ Series Motor Control Development Kit
User Manual
11
•
Heat sink temperature sensor
•
Spade lug connectors for power input from adjustable 24 VDC power source (for con-
nection to 3-phase motor)
•
5 A fuse, F1
•
Two 60-pin headers for connection to the MC MDS Module (JP1 and JP2; JP1 used
for physical mounting only)
Power MOSFETs and Gate Drivers
Each of the phase outputs on spade lugs P1, P2, and P3 are driven by a pair of power
MOSFETs, one for the high side and one for the low side. A gate driver circuit is associ-
ated with each pair of power MOSFETs.
Fused External Power Interface
An interface to an adjustable 0 VDC to 24 VDC workbench power supply is provided
through spade lug connectors P4 (+) and P5 (–). The input power is fused through 5 A
3 AG fuse F1.
Physical Dimensions
The footprint of the 3-Phase Motor Control Application Board PCB is 12.44 cm x
12.44 cm. With the MC MDS module mounted on it, the overall development kit height is
4.31 cm.
ZDS II
The Zilog Developer Studio II (ZDS II) Integrated Development Environment (IDE) is a
complete stand-alone system that provides a state-of-the-art development environment.
Based on the Windows
®
XP/Vista-32/Win 2000-SP4 user interfaces, ZDS II integrates a
language-sensitive editor, project manager, C-Compiler, assembler, linker, librarian, and
source-level symbolic debugger that supports the Z16FMC Series of devices.
Troubleshooting and Developer Guidelines
Before contacting Zilog Customer Support to submit a problem report, follow the steps
below. If there is a hardware failure, contact a local Zilog representative for assistance.
Linix Motor Wiring Information UM023402-0811
12
Z16FMC™ Series Motor Control Development Kit
User Manual
Recheck Procedures with the Quick Start Guide
Follow the procedures in the Z16FMC
™
Series Motor Control Development Kit Quick
Start Guide (QS0079) – contained in the kit – and verify that the kit is set up as specified
in the document.
Zilog Customer Support Contact
For additional troubleshooting solutions, refer to ZDS II Online Help. For valuable infor-
mation about customer and technical support, as well as hardware and software develop-
ment tools, visit the Zilog website at w
ww.zilog.com, where you’ll also find the latest
released versions of ZDS II.
Linix Motor Wiring Information
The Linix 3-phase motor included with the development kit provides three heavy-gauge
wires for phase connections and five light-gauge wires used to power and access internal
sensors, as indicated in Table 4.
Table 4. 3-Phase Motor Wiring Information
Wire Description
Heavy-gauge white wire Motor Phase A connection
Heavy-gauge blue wire Motor Phase B connection
Heavy-gauge green wire Motor Phase C connection
Light-gauge red wire Sensor power V
CC
(+)
Light-gauge black wire Sensor power ground (-)
Light-gauge white wire Sensor signal S
A
Light-gauge blue wire Sensor signal S
B
Light-gauge green wire Sensor signal S
C
UM023402-0811 Schematic Diagrams
Z16FMC™ Series Motor Control Development Kit
User Manual
13
Schematic Diagrams
Figures 7 through 9 display schematics for the 3-Phase Motor Control Application Board.
Figure 7. 3-Phase Motor Control Application Board Schematic, #1 of 3
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
V+
PHASE_A PHASE_BPHASE_BPHASE_B PHASE_C
GATE_AH
GATE_AL GATE_BL
GATE_BH
GATE_CH
GATE_CL
+BUS+BUS+BUS+BUS+BUS+BUS+BUS+BUS+BUS+BUS+VDC +BUS+BUS+BUS+BUS+BUS+BUS+BUS+BUS+BUS+BUS
GND
TH
CS+
CS-
TH
Title
Size Document Number Rev
Date: Sheet
of
96C0960-001
C
3 PHASE MOTOR CONTROL APPLICATION BOARD
A
13Monday, April 26, 2010
Title
Size Document Number Rev
Date: Sheet
of
96C0960-001
C
3 PHASE MOTOR CONTROL APPLICATION BOARD
A
13Monday, April 26, 2010
Title
Size Document Number Rev
Date: Sheet
of
96C0960-001
C
3 PHASE MOTOR CONTROL APPLICATION BOARD
A
13Monday, April 26, 2010
3 PHASE POWER STAGE
HEATSINK TEMP SENSOR
AB C
R5
10.00k
R5
10.00k
Q3
IXTP64N055T
Q3
IXTP64N055T
+
C4
3300uF 50V
+
C4
3300uF 50V
Q2
IXTP64N055T
Q2
IXTP64N055T
R4
NTC 10k
R4
NTC 10k
P5P5
P2P2
Q1
IXTP64N055T
Q1
IXTP64N055T
F1
5A FUSE
F1
5A FUSE
Q6
IXTP64N055T
Q6
IXTP64N055T
R6
150k
R6
150k
R3 10.0kR3 10.0k
C3
0.1uF 50V
C3
0.1uF 50V
Q5
IXTP64N055T
Q5
IXTP64N055T
C2
0.1uF 50V
C2
0.1uF 50V
P4P4
R2 10.0kR2 10.0k
+
C5
3300uF 50V
+
C5
3300uF 50V
P1P1
C1
0.1uF 50V
C1
0.1uF 50V
R1
0.100 OHM
R1
0.100 OHM
Q4
IXTP64N055T
Q4
IXTP64N055T
P3P3
Schematic Diagrams UM023402-0811
Z16FMC™ Series Motor Control Development Kit
User Manual
14
Figure 8. 3-Phase Motor Control Application Board Schematic, #2 of 3
5
5
4
4
3
3
2
2
1
1
D
D
C
C
B
B
A A
GATE DRIVE
BEMF DIVIDERS
12V SUPPLY
96C0960-001
B
3 PHASE MOTOR CONTROL APPLICATION BOARD
A
23Wednesday, June 08, 2005
Title
veRrebmuN tnemucoDeziS
teehS:etaD
of
GATE_AL
GATE_AH
PHASE_AAL
AH
PHASE_BBL
BH
GATE_BL
GATE_BH
PHASE_C
CH
GATE_CL
GATE_CH
PHASE_A PHASE_B PHASE_C
VAVA VBVBVBVB
CL
VCC_3.3V
VC
+12V
+12V
+12V
+12V
R10
150k
C6
10uF
R18 22.1
C19
10uF
C11
0.1uF
R12
150k
C13
10uF
R13 22.1
R20
86.6k
R7
10.00k
U2
IR2101
1
2
3
4
5
6
7
8
VCC
HIN
LIN
COM LO
VS
HO
VB
D3 BAV19
C12
0.1uF
L1
10uH
R15 22.1
R14 22.1
R9
10.00k
C14
10uF
C20
68pF
R11
10.00k
R16 22.1
U1
IR2101
1
2
3
4 5
6
7
8
VCC
HIN
LIN
COM LO
VS
HO
VB
C8
0.1uF
D4 BAV19
C17
10uF
D2 BAV19
C15
0.1uF
U3
IR2101
1
2
3
4
5
6
7
8
VCC
HIN
LIN
COM LO
VS
HO
VB
U4
TPS61041
1
2
3
4
5
SW
GND
FB
EN
VIN
R8
150k
D1 BAV19
C16
0.1uF
C18
10uF
C7
0.1uF
R17 22.1
C10
10uF
R19
10.0k
C9
10uF
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

ZiLOG Z16FMC3 User manual

ZiLOG
Brand
ZiLOG
Model
Z16FMC3
Type
User manual
This manual is also suitable for

ZiLOG Z16FMC3 is a versatile Flash microcontroller based on Zilog’s advanced ZNEO 16-bit CPU core. Optimized for motor control applications, this device supports the control of single- and multi-phase variable-speed motors. Target applications are large appliances, small appliances and HVAC.

Key features include:

  • 16-bit optimized single-cycle CISC core
  • Up to 128 KB of in-circuit programmable Flash memory
  • 12-Channel, 10-bit ADC with a 2.1μs conversion time
  • Highly integrated digital/analog peripherals
    • Operational Amplifier
    • Analog Comparator
    • Internal Precision Oscillator
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents