Blue Sea Systems 1836 Installation guide

Blue Sea Systems
Brand
Blue Sea Systems
Model
1836
Type
Installation guide
Connector Pin Assignment System Overview
Screen Menu Functions
M2 OLED
Digital Monitor
QuickStart Installation Guide
360 Panel Mounting Kit PN 1525 sold separately
425 Sequoia Drive
Bellingham, WA 98226 USA
www.bluesea.com
p 360.738.8230
[email protected]
Components Included
1836 AC Ammeter
www.bluesea.com/products/1836
980020440 Rev.002
If you are not knowledgeable about electrical systems, have an
electrical professional install this unit. The diagrams in these
instructions pertain to the installation of the unit and not to the
overall wiring of the vessel.
Verify that all AC sources are disconnected before connecting or
disconnecting the Current Transformer (CT). Failure to do so will
generate lethal voltages on the CT.
If an inverter is installed on the vessel, its power leads must be
disconnected at the battery before the unit is installed. Many
inverters have a “sleep mode” in which their voltage potential may
not be detectable with measuring equipment.
If an AC generator is installed on the vessel, it must be stopped
and rendered inoperable before the unit is installed.
Verify that no other DC or AC sources are connected to the vessel’s
wiring before installing the unit.
If the unit must be removed, connect the CT leads together before
restoring power to the AC system.
WARNING
The back of the unit is not waterproof. Do not install where
the back of the monitor is exposed to water.
CAUTION
WARNING
The WARNING symbol refers to possible injury to the user or
significant damage to the monitor if the user does not follow
the procedures.
CAUTION
The CAUTION symbol refers to restrictions and rules with
regard to preventing damage.
Press any button to bring up the menu.
1. After start-up, press any button to access the menu.
2. Press the UP or DOWN arrow buttons to scroll through menu windows.
3. To set alarms and for more detailed information, see the online
manual at www.bluesea.com/products/1836
Connector Pin Assignment Table
8 Pin Connector*
Function
The M2 OLED Digital Meters come with a 5 year manufacturer’s
warranty. This means the meter is warranted to be free from defects
in materials or workmanship for 5 years from the date of first
purchase. The warranty is limited solely to the cost of repair or
replacement of the M2 Meter product. Costs associated with labor
or shipping of the defective parts are not covered.
Blue Sea Systems cannot accept liability for damage due to the
misuse of the M2 Meter.
Warranty
1 Required Connection
2
Required Connection
3
4
5
6
7
8
USB
DC Negative
DC Positive
Relay DC Out to Load
Relay DC +
AC 1 Current Transformer –
AC 1 Current Transformer +
AC 2 Current Transformer –
AC 2 Current Transformer +
Micro USB Port
Relay
(7713 12V)
(7717 24V)
Alarm (1070)
LED
(8033 Amber)
(8171 Red)
(8172 Green)
OROR
For the online manual that includes other configurations,
go to www.bluesea.com/products/1836
Optional
Transformer
AC Current Transformer
8256 (1X)
M2 Head Unit Surface Mount Gasket
Mounting Ring
Surface Mount Bezel
and Seal
Mounting Nut
Flat Mount Bezel
Screwdriver
(retail package only)
Bezel
Mount
Footer
Header
Carrier
Mount
#6-32 x 1/4"
Flat Head
Machine Screws
(4X)
#6-32 x 3/8"
Flat Head
Machine Screws
(4X)
Surface Mount Cover
Flat Mount Clamp
1836 AC Ammeter Connections
M2 Meter Navigation
Panel
Frame
To loads
From source
To loads
12345678
AC
1 H
AC
2 H
Connector
*The 8 pin low voltage connector supports wire sizes from 16-26 AWG
Flat Mount
Surface Mount
360 Panel Mount
PN 1525
(If retrofit to existing panel)
Mounting TemplatesMounting Options
STEP 1
STEP 2
STEP 3
Mounting
Substrate
Mounting
Substrate
Clamp
Flat
Mount
Bezel
Panel
Frame
360 Panel
Mount
Carrier
M2
Head
Unit
M2
Head
Unit
Surface
Mount
Bezel
and Seal
Panel
Frame
BezelFooter
Header
M2
Head
Unit
Use 1/4"
Mounting
Screws
Mounting
Ring and Nut
Surface
Mount
Gasket
Mounting
Ring and Nut
Mounting
Ring and Nut
Surface
Mount
Cover
Footer
Panel
Frame
Bezel
Header
Snap header
and footer
into mounting
clips and post.
Snap the
mounting bezel
into place
with the flat
edge up.
NOTE: During
installation use cover
to align the bezel
and gasket
Surface Mount
3.40" (86.5mm)
3.46" (87.9mm)
Ø2.125"
(54mm)
Flat Mount
3.34" (84.8mm)
3.00" (76.2mm)
3.00" (76.2mm)
3.34" (84.8mm)
  • Page 1 1
  • Page 2 2

Blue Sea Systems 1836 Installation guide

Blue Sea Systems
Brand
Blue Sea Systems
Model
1836
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents