JVC LT-55N6105A LED TV Owner's manual

LT-55N6105A 55" 4K UHD

Q.MENU

MENU

INPUT

HOME

EXIT

BACK

INFO

SUBTITLE

Pg Dn

RECALL

GUIDE

1

2

3

4

Table of Contents

Never place a television set in an unstable location. A television set may fall, causing serious personal

injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such

as:

- Using cabinets or stands recommended by the manufacturer of the television set.

- Only using furniture that can safety support the television set.

- Ensuring the television set is not overhanging the edge of the supporting furniture.

- Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring

both the furniture and the television set to a suitable support.

- Not placing the television set on cloth or other materials that may be located between the television set

and supporting furniture.

- Educating children about the dangers of climbing on furniture to reach the television set or its

controls

If your existing television set is being retained and relocated, the same considerations as above should

be applied.

The plug or appliance coupler is used as the disconnect device, the disconnect device shall remain

readily operable.

WARNING

5

6

7

8

9

10

11

14

15

16

17

18

19

20

22

23

25

27

28

30

32

33

35

37

38

Accessories-------------------------------------------------------------------------------------------------------------

Introduction-------------------------------------------------------------------------------------------------------------

Basic Functions----------------------------------------------------------------------------------------------------------

Specifications-------------------------------------------------------------------------------------------------------------

Stand instructions (optional)--------------------------------------------------------------------------------------

General Description--------------------------------------------------------------------------------------------------

Overview of back panel------------------------------------------------------------------------------------------------

Overview of front panel------------------------------------------------------------------------------------------------

Overview of remote control--------------------------------------------------------------------------------------------

Installing Batteries in the Remote Control-------------------------------------------------------------------------

External Connection--------------------------------------------------------------------------------------------------

Antenna connection-----------------------------------------------------------------------------------------------------

Connecting VCR---------------------------------------------------------------------------------------------------------

Connecting a Camcorder----------------------------------------------------------------------------------------------

Connecting DVD Player/Set-Top Box via HDMI-----------------------------------------------------------------

Connecting Digital Audio System------------------------------------------------------------------------------------

Supporting signals----------------------------------------------------------------------------------------------------

Basic operation---------------------------------------------------------------------------------------------------------

Menu Operation----------------------------------------------------------------------------------------------------------

Menu system instruction--------------------------------------------------------------------------------------------

Picture----------------------------------------------------------------------------------------------------------------------

Sound ---------------------------------------------------------------------------------------------------------------------

Setting ---------------------------------------------------------------------------------------------------------------------

Lock-------------------------------------------------------------------------------------------------------------------------

PVR Option---------------------------------------------------------------------------------------------------------------

Program-------------------------------------------------------------------------------------------------------------------

Network -------------------------------------------------------------------------------------------------------------------

About ----------------------------------------------------------------------------------------------------------------------

Home Operation ------------------------------------------------------------------------------------------------------

SOURCE setup --------------------------------------------------------------------------------------------------------

APP setup ---------------------------------------------------------------------------------------------------------------

Digital Media Player---------------------------------------------------------------------------------------------------

Troubleshooting--------------------------------------------------------------------------------------------------------

5

Accessories

Please make sure the following items are included with your LED TV. If any items are missing,

contact your dealer.

1 x remote control

2 x AAA batteries

1 x user manual

2 x Base Legs

4 x Base Screws

1 x 3.5mm to L-R Audio Cable

1 x 3.5mm to Y/V, Pb, Pr Video Cable

6

Introduction

Basic Functions

Input terminals used for external equipment connection

1 x ANT. IN input

2 x USB inputs

3 x HDMI inputs

1 x Shared Mini Component and Composite Input

1 x Digital Optical Audio Out

1 x Headphone output

1 x RJ-45 input

7

Introduction

Specifications

NOTES:

• Design and specifications are subject to change without notice.

• Weight and Dimension shown are approximate.

Digital: DVB-T

Analog: PAL: BG, I, DK,

SECAM: BG, D/K

TV receive system

Analog: Antenna:

46.25MHz-855.25MHz

Digital：

DVB-T/T2: 5-12,21-69

TV with stand

TV without stand

TV with stand

TV without stand

≤ 1W

Standby comsumption

Weight

(Net weight)

Dimensions

(LxWxH)

Model

LED panel resolution

≥5Wx2

Speaker output power

Power supply

Frequency range

PAL/NTSC/SECAM

Video in

Power consumption

DC 3V

(Two AAA size batteries)

Controller power

o o

0 C-40 C

Operating temperature

Display size

Antenna input

75 ohms

110-240V~, 50/60Hz

150W

400 cd/m

5000:1(Dynamic)

Brightness(typ.)

Contrast ratio

2

3840x2160

55" Diagonal (max.)

LT-55N6105A

1227X86.9X722.3mm

1227X266X777.7mm

10.4kg

10.25kg

8

Stand instructions (optional)

How to assemble the stand

If you need to remove or assemble the stand please read the following instructions.

- Before attaching/detaching the stand, make sure to turn off the TV.

-Lay the TV face down on a soft cloth or a towel to prevent scratches.

Assembling instruction:

- To disconnect the stand from the TV, perform the above steps in reverse order.

Step2: Align the Base Legs against the corresponding screw holes on the bottom of the TV.

Insert and tighten the screws to attach the Base Legs to the TV.

Step2: Before performing work, spread cushioning over the base area to lay the LED TV on.

Put the television on the table.

9

General Description

Overview of back panel

General Description

Overview of back panel

You can connect the TV with video devices such as DVD/VCD player, VCR and video camera to

enjoy the high quality picture.

General Description

Overview of back panel

Headphone

DVD player

Camcorder

DVD player

PC (HDMI-output)

Blu-ray disc player

USB

Note:

The product and illustrations in this user's manual are only for explanation purposes and

may vary depending on model.

ANTENNA

Y/V

Pb

Pr

YPbPr/V

L

R

AUDIO

HDMI 1

(ARC)

HDMI 2

HDMI 3

USB 1

5V 500mA

USB 2

5V 500mA

OPTICAL

OUT

General Description

Overview of front panel

10

The Multifunction Button on the bottom of your TV(see below) can control your TV’s basic features,

including the on-screen menu. To use the more advanced features, you must use the remote control.

Multifunction Button Description

Display/Hide the icons: Press the Multifunction Button once to display the icons shown above.

The icons will be hidden after 5 seconds of inactivity.

Short press the button, move the loop to the right, select the icon.Icon selection:

Long press the key to achieve the function of the selected icon.Icon function selection:

Icon Description:

Power off Icon: Corresponding to the “POWER” button of remote.

CH+ Icon: Corresponding to the “CH+” button of remote.

CH- Icon: Corresponding to the “CH-” button of remote.

Input Icon: Corresponding to the “Input” button of remote.

Volume+ Icon: Corresponding to the “VOL+” button of remote.

Volume- Icon: Corresponding to the “VOL-” button of remote.

Remote Control Sensor/Power Indicator

POWER(power on / key function)

CH+

Press&Hold: Select Press: Move

CH- VOL+ VOL- INPUT

Q.MENU

MENU

INPUT

HOME

EXIT

BACK

INFO

SUBTITLE

Pg Dn

RECALL

GUIDE

11

Note:

1) On average, the batteries should last for about a year.

2) If you don't intend to use the remote control for a long period of time, remove batteries

to avoid damage due to leakage.

3) Do not mix old and new batteries or different types.

4) Do not throw batteries into fire or water.

5) The batteries (battery pack or batteries installed) should not be exposed to excessive

heat such as sunshine, fire or the like.

General Description

Overview of Remote Control



Ž



‘

’

“

”

•

Œ



12

General Description

Overview of Remote Control

1. POWER: Turn the TV on or switch it to standby.

2. INPUT: This button is used to switch among

different sources, Select a source and press

ENTER button to confirm.

3. Number Buttons(0-9): Directly select channel

with buttons.number

4. RECALL: Switch to the previous program.

5. INFO: Display the program information.

6. GUIDE: Open the Electronic Program Guide (EPG)

in DTV mode.

7. When connected to a network,YouTube: press this

key to view YouTube directly.

8. HOME: Press it to go to App home page.

9. NETFLIX: When connected to a network, press this

key to view NETFLIX directly.

10. Q.MENU: Press this key to go to quick menu.

11. MENU: Display the main menu or exit the

current menu.

12. ENTER: Validation key.

Q.MENU

MENU

INPUT

HOME

EXIT

BACK

INFO

SUBTITLE

Pg Dn

RECALL

GUIDE



Ž



‘

’

“

”

•

Œ



13

General Description

Overview of Remote Control

13. Arrow button : Use to select s pqtu

on-screen menu items and change menu

values.

14. BACK: Return.

15. source button: In ATV , the button is used to

set NICAM sound system. In DTV , the source

button is used to set the audio language.

16. EXIT: Exit the menu.

17. VOL -: Press these buttons to adjust the +/

volume.

18. CH : / Press these buttons to change channel

upward or downward.

19. MUTE: Press this button to cut off the sound of

the TV set temporarily, press again to resume.

20. COLOR It's used as shown in the EPG BUTTONS:

or Program Edit menu.

21. DIGITAL MEDIA PLAYER CONTROL BUTTONS:

Includes Play/Pause, Stop, Previous, Next, Back,

Forward used in USB mode. A USB memory

device must be connected to one of the USB ports

for recording.

22. SUBTITLE: In USB mode, press this button to

turn on/turn off subtitles (for a program with

subtitles).

Q.MENU

MENU

INPUT

HOME

EXIT

BACK

INFO

SUBTITLE

Pg Dn

RECALL

GUIDE



Ž



‘

’

“

”

•

Œ



14

External Connection

Antenna connection

Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected

to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder cable, you need to

use the 300ohm/75ohm converter to connect the antenna cable to the antenna jack. For details

please refer to the following drawing.

75ohm coaxial cable

Antenna cable

Antennas with 300 W flat twins Leads

Antennas with 75 W Round Leads

Use a 75ohm - 300ohm converter

300ohm coaxial cable

Antenna feeder

General Description

Installing Batteries in the Remote Control

Installing Batteries

1

Open the battery compartment

cover on the back side.

2

Insert two 1.5V AAA size batteries

in correct polarity. Don´t mix old or

used batteries with new ones.

3

Point the remote towards the remote control

sensor of the TV and use it within 8 meters.

Do not put used batteries in your household

rubbish as this can negatively affect the

environment. Contact your local council for

battery recycling options.

Close the cover.

15

These instructions assume that you have already connected your TV to an antenna or a cable

TV system. Skip step 1 if you have not yet connected to an antenna or a cable system.

VCR Rear Panel

TV Rear Panel

White

Red

ANT

ANT OUT S-VIDEO

AUDIO OUT

Red

Blue

Green

VIDEO OUT

2

3

Red

Blue

Green

2

Red

White

3

1

Follow the instructions in Viewing a VCR or Camcorder Tape to

view your VCR tape.

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection

terminal to the cable.

1. Unplug the cable or antenna from the back of the TV.

2. Connect the cable or antenna to the ANT IN terminal on the

back of the VCR.

3. Connect an RF Cable between the ANT OUT terminal on the

VCR and the ANT IN terminal on the TV.

4. Connect a Component Cable between the COMPONENT

[Y, Pb, Pr] jacks on the DVD player and YPbPr jack on the TV.

5. Connect Audio Cables between the AUDIO OUT jacks on the

VCR and the AUDIO jack on the TV.

Note:

1. Whenever you connect an external device to your TV, make

sure that power on the unit is turned off.

2. When connecting an external device, match the color of the

connection terminal to the cable.

2

1

Audio Cable (Not supplied)

YPbPr cable(Not supplied)

RF Cable (Not supplied)

3

ANTENNA

Y/V

Pb

Pr

YPbPr/V

L

R

AUDIO

HDMI 1

(ARC)

HDMI 2

HDMI 3

USB 1

5V 500mA

USB 2

5V 500mA

OPTICAL

OUT

16

The rear panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you

to view the camcorder tapes without using a VCR.

Each Camcorder has a different back panel configuration.

When connecting a Camcorder or DVD, match the color of the connection terminal to the cable.

Green

Red

White

1. Connect a Video Cable between the Y/V,Pb,Pr jack on the TV and

the VIDEO OUT jack on the camcorder/ DVD player..

2. Connect Audio Cables between the AUDIO L and AUDIO R jacks on the

TV and the AUDIO OUT jacks on the camcorder/DVD player..

Notes:

1. Whenever you connect an external device to your TV, make sure

that power on the unit is turned off.

2. When connecting an external device, match the color of the

connection terminal to the cable.

White

Red

Camcorder

Video Cable (Not supplied)

1

Audio Cable (Not supplied)

2

TV Rear Panel

Green

Blue

Red

White

Red

ANTENNA

Y/V

Pb

Pr

YPbPr/V

L

R

AUDIO

HDMI 1

(ARC)

HDMI 2

HDMI 3

USB 1

5V 500mA

USB 2

5V 500mA

OPTICAL

OUT

17

External Connection

Connecting DVD Player/Set-Top Box via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

What is HDMI?

HDMI, or high-definition multimedia interface, is an interface that enables the transmission of digital

audio and video signals using a single cable without compression.

Multimedia interface is a more accurate name for it especially because it allows multiple channels

of digital audio (5.1 channels).

Each DVD player/STB has a different back panel configuration.

Connect an HDMI Cable between one of the HDMI connectors on the TV and the HDMI connector

on the DVD player/Set-Top Box.

Notes:

1.Whenever you connect an external device to your TV, make sure that power on the unit

is turned off.

2.When connecting an external device, match the color of the connection terminal to the

cable.

HDMI Cable (Not supplied)

TV Rear Panel

HDMI 1

(ARC)

HDMI 2

HDMI 3

18

External Connection

Connecting Digital Audio System

5.1 CH audio is possible when the TV is connected to an external device

supporting 5.1 CH.

Connect an OPTICAL Cable between the Optical Output on the TV and the

Digital Audio Input jacks on the Digital Audio System. When a Digital Audio

System is connected to the OPTICAL terminal:

Decrease the gain (volume) of the TV, and adjust the volume level with the

Digital Audio System's volume control.

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

Digital Audio System

TV Rear Panel

OPTICAL

SPDIF

ANTENNA

Y/V

Pb

Pr

YPbPr/V

L

R

AUDIO

HDMI 1

(ARC)

HDMI 2

HDMI 3

USB 1

5V 500mA

USB 2

5V 500mA

OPTICAL

OUT

Page is loading ...

JVC LT-55N6105A LED TV Owner's manual

JVC LT-55N6105A LED TV Owner's manual

Related papers

Other documents