CELED494K1018B7
49" SCREEN UHD LED TV
User manual
2
IMPORTANT WARNINGS AND SAFETY ADVICE
We invite you to read this user manual carefully and
completely before installing and using your device.
It is important that this user manual be kept with the device for
further consultation. If this device is to be transferred to another
person, make sure the user manual follows the device so that
the new user can be informed of the operation of the device.
The warning sign showing a lightning bolt in a
triangle indicates that this product contains
"dangerous electrical voltages".
CAUTION: TO AVOID THE RISK OF
ELECTROCUTION, DO NOT REMOVE
THE COVER (OR THE BACK OF THE
DEVICE).
NO PARTS ARE REPLACEABLE BY THE USER. PLEASE
CONTACT QUALIFIED PERSONNEL IN CASE OF FAILURE.
CAUTION
RISK OF ELECTRIC
SHOCK POWERED
DEVICE
DO NOT OPEN
The warning sign showing an exclamation
point in a triangle indicates that this point of
the manual requires special attention.
3
CAUTION: - TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR SERIOUS INJURY:
● This device must only be connected to a mains network
whose characteristics are identical to those shown on the
device identification plate.
● The mains plug must always be easily accessible. It serves
as a mains disconnecting switch of the device.
● To disconnect the device from the mains, the plug must be
disconnected. Hold the mains cable by its plug. Do not pull on
the mains cable to disconnect the plug.
● The mains cables must be routed so that they are not
trampled upon or pinched by objects placed on or against
them.
● If the mains cable of the device is damaged, it must be
replaced by the manufacturer, its after-sales service or a
similarly qualified person to avoid any danger.
● The device must not be exposed to dripping or splashing
water, moisture or liquids.
● Do not place the device near water, for example in a
bathroom or near a sink.
● No objects filled with liquids such as vases should be placed
on or above the device.
● Never touch the mains cable with wet hands, this could cause
a short circuit or electric shock.
● To avoid the risk of fire, do not place sources of open flames,
such as lighted candles, or heat sources such as radiators,
on or near the device.
● The device is intended for use only in a temperate climate.
● If smoke, an unusual odour or strange noise is emitted by the
device: unplug the mains cable from the electrical outlet and
consult the after-sales service or repair centre. Never attempt
4
to make repairs yourself, this could be potentially dangerous.
● Do not attempt to open or disassemble the device. This
would expose you to dangerous voltages.
● The slots and openings of the device are intended for
ventilation and to ensure its operation. To prevent
overheating, these openings must not be obstructed or
covered in any way, such as by newspapers, tablecloths or
curtains.
● Always leave a minimum distance of 10 cm around the
device for sufficient ventilation.
● Never push any object into the device through one of its
openings, as it may come into contact with electrical
components, which can cause an electric shock or fire.
● In case of thunderstorm or lightning, immediately unplug the
mains cable from the wall outlet.
● Always turn off the device when not in use. Unplug the mains
cable from the electrical outlet when the device will not be
used for a long period of time.
● Unplug the device from the electrical outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a dry, soft cloth for
cleaning.
● If the product does not bear the logo, it is a Class I
device. It must then be connected to a mains socket with a
protective earth connection.
CAUTION –: TO AVOID RISK OF INJURY OR
DAMAGE TO THE PRODUCT OR OTHER
EQUIPMENT:
● This product is intended for household and personal use only.
Do not use this product for commercial, industrial or other
purposes.
● Do not subject the product to strong shocks, extreme
temperatures or direct sunlight for prolonged periods.
5
● Keep the product away from magnetic objects, motors and
transformers.
● Do not use the product outdoors, regardless of weather
conditions.
● Install the device only on a stand (furniture, wall,…) that can
support its weight safely.
● WARNING: never place a TV on an unstable location. This
can fall, causing injuries or even the death of a person. Many
injuries, especially in the case of children, can be avoided by
taking simple precautions such as:
- The use of furniture or stands recommended by the TV
manufacturer.
- The exclusive use of furniture that can support the weight of
the TV safely.
- Make sure that the device does not protrude from the edge of
the furniture on which it is placed.
- Never place the device on a tall piece of furniture (e.g.
cabinets or bookcases) without attaching both the furniture
and the device to a suitable stand.
- Do not place the device on a trolley or on a stand that is not
stable. Do not install the device on any fabric or other
materials placed between its base and the supporting
furniture. The device could fall and be damaged or seriously
injure a person.
- Do not use or watch the TV while driving. This is dangerous,
and illegal in some countries.
- Explain to children the dangers they face when climbing on
the furniture to reach the device or its controls.
- If you keep this device and change the location, you should
apply the same considerations.
- CAUTION: to avoid accidents, this device must be securely
attached to the floor or wall according to the installation
6
instructions.
CAUTION: TO AVOID EYE HAZARDS:
● It is best to have soft indirect lighting to watch TV. Avoid
completely dark environments and any reflection on the
screen, as these can cause eyestrain.
USE AND HANDLING OF BATTERIES:
● CAUTION: danger of explosion if the batteries are not
inserted correctly or if they are replaced by a non-similar or
incompatible model.
● Replace the batteries only with batteries of the same type or
equivalent type.
● Batteries must not be exposed to excessive heat such as that
from the sun, fire or similar origin.
● Never throw batteries into fire and never expose them to heat
sources.
● Do not mix different types of batteries, or new and used
batteries.
● The batteries must be inserted according to the polarities
indicated on the battery and in the battery case of the remote
control.
● Used batteries must be removed from the remote control.
● The batteries must be disposed of safely at the assigned
specific collection points to preserve the environment. Follow
the disposal instructions indicated on the batteries and at the
collection points.
● Keep batteries out of the reach of children and animals. Only
adults are capable of handling the batteries.
7
For installation, handling, cleaning and disposal of the
device, refer to the following chapters of the user manual.
To avoid possible hearing damage, do not listen
at a high sound level for a long time.
EU Declaration of Conformity:
Market Maker Brand Licensing hereby declares that the device complies with the essential requirements and
other relevant provisions of Directive 2014/53/EU. The Declaration of Conformity can be viewed at the
following address:
http://www.mms-support.net/OTA/ECD_MMBL_CELED494K1018B7.pdf
8
SUMMARY
I. DESCRIPTION OF THE DEVICE ...................................................................................................... 10
A. Description of the TV ........................................................................................................................ 10
B. Remote control .................................................................................................................................. 12
II. TECHNICAL CHARACTERISTICS .................................................................................................... 14
III. INSTALLATION ................................................................................................................................. 16
A. Unpacking .......................................................................................................................................... 16
B. Wall mounting .................................................................................................................................... 16
C. Installing the feet ........................................................................................................................... 17
D. Basic connections ......................................................................................................................... 18
IV. OPERATION ...................................................................................................................................... 22
A. First Time installation ....................................................................................................................... 22
B. Main menu (TV settings) .................................................................................................................. 23
C. Basic operations ............................................................................................................................ 23
D. Setup ............................................................................................................................................... 28
1. Channel menu .................................................................................................................................. 29
2. Picture menu ................................................................................................................................... 31
3. Sound menu ..................................................................................................................................... 32
4. Time menu ....................................................................................................................................... 33
5. Lock menu ........................................................................................................................................ 35
6. Settings menu .................................................................................................................................. 36
E. AV and other modes ......................................................................................................................... 37
V. MAINTENANCE AND CLEANING ..................................................................................................... 38
VI. TROUBLESHOOTING TIPS ........................................................................................................... 39
VII. WARRANTY ...................................................................................................................................... 41
VIII. DISPOSAL ......................................................................................................................................... 42
9
This user manual, any modifications or any new version, is available on our website.
Information on the meaning of the conformity marking
The CE marking indicates that the product meets the main requirements of the European Directives
2014/35/EU (Low Voltage), 2014/30/EU (Electromagnetic Compatibility), 2014/53/EU (Radio Equipment),
2011/65/EU (Limitation of use of certain hazardous substances in electronic equipment).
10
I. DESCRIPTION OF THE DEVICE
A. Description of the TV
Front view of the TV
1- LED screen.
2- Feet.
3- IR (Infrared) sensor for remote control / power indicator.
4- STANDBY : (On/Off) to turn the TV on or off.
5- SOURCE : to select the input source.
6- MENU : to display the settings menu.
7- CH + / CH - : to scroll through the channels to the next or the previous one.
8- VOL + / VOL - : to increase or decrease the volume.
11
Back view of the TV
1. EARPHONE OR HEADPHONE OUTPUT: to connect a 3.5mm headphone jack.
2. COAX: to connect an external amplifier via a coaxial cable.
3. L / R / Video (AV): to connect the source of a VCR or DVD player.
4. YPbPr: to connect the YPbPr cable of a VCR or DVD player.
5. HDMI1 / HDMI2 / HDMI3 / HDMI4: allows the broadcast of an uncompressed digital video and
audio signal via a single cable.
6. ANT: to connect the coaxial cable of a terrestrial antenna.
7. USB1 / USB 2: to connect a USB device, such as a storage device to access the TV's media
functions.
8. VGA (PC): To connect your computer or other device equipped with a VGA jack for 15-pin D-
sub cable.
9. PC AUDIO: to broadcast the PC sound on the TV. Use a 3.5 mm stereo cable to connect the
PC to the TV.
12
B. Remote control
1- STANDBY
To put the TV on standby or turn it on.
2- MUTE
To turn off the sound.
3- NUMERIC KEYS
Press the keys to directly dial the channel number
you want to view.
4- TEXT
To display teletext.
5- PREVIOUS KEY
To return to the previous channel.
6- PMODE
To switch between image modes.
7- SMODE
To switch between the different Audio modes.
8- AUDIO
To select an audio track.
9- SLEEP
To set the time before standby.
10- SOURCE
To change the video source.
11- INFO
To view the source and available
information about a program.
12- CH + / CH -
To view the next or previous channel.
13- VOL + / VOL -
To increase or decrease the volume.
14- COLOURED KEYS
The coloured keys are used in the submenus.
15- ▲/▼/◄/►
Navigation keys.
16- OK
To confirm the selection.
17- MENU
To display the main menu or the previous menu.
18- EXIT
To exit the menu page.
19- SUBTITLE
To show or hide subtitles.
13
20- INDEX
To display the list of recordings or the teletext
index.
21- SIZE
Press repeatedly to change the size of the image.
22- REVEAL
To show or hide hidden texts in teletext mode.
23- MIX
TV and TXT images are mixed on a transparent
background.
24- HOLD
Play/Pause during Timeshift.
25- CANCEL /
To exit the OSD menu./ To read the previous file.
26- SUBPAGE /
To display the teletext subpage. / To read the next
file.
27- TVG
To view the digital program guide.
28- FAV /
To view the list of favourite programs./ To stop
playback.
29- FAV – /
To delete a channel from the list of favourite
programs. / For rewind.
30- FAV + /
To add a channel to the list of favourite programs./
For fast forward.
31- MEDIA
To enter the media (USB) mode immediately.
32- REC
To start RECORDING a digital program (in DTV
mode).
33- TIMESHIFT (Direct control)
To pause the current DTV program, and start
recording in the background.
34- TV / RADIO
To switch between TV and radio modes.
14
II. TECHNICAL CHARACTERISTICS
Reference
CELED494K1018B7
Model
NM49
Display
49" UHD LED TV
Resolution
3840 x 2160 pixels
Colour display
1.07G
Contrast
1200:1
Ratio
16:9
Service life
30.000 hours
Tuner
DTV HD (digital channel reception, TV guide, teletext display, multi-
language display)
TV power supply
100-240V~ 50/60Hz
Consumption
<108W
Dimensions
1224mm (L) × 151mm (D) × 752mm (H)
Weight
Approx. 13.7Kg
Base
Removable, in 2 parts
Operating temperature
0°C to 40°C
Remote control power supply
3V (2 x LR03/AAA 1.5 V batteries, not supplied)
USB port power supply
5V 0.5A
Hotel lock
Yes
Speaker
Built-in 2 x 8W
Inputs
Antenna, HDMI, YPbPr, AV, USB
Outputs
Earphones, Coaxial, Audio (L/R)
Functions via USB
PVR (digital video recorder)
Multimedia playback formats via
USB
Video: AVI, MP4, MOV, MPG, MKV, DAT, VOB, RMVB, TS, TRP, TP
Music: MP3, WMA, WAV, M4A, AAC
Photos: JPEG, PNG
Text: TXT, SRT, SSA, ASS, SMI, SUB
These characteristics are subject to change without notice.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI logo are trademarks of HDMI Licencing LLC in the
United States and other countries.
15
ACCESSORIES:
Feet ...................................................................................................................................................... 2 pieces
Remote control ..................................................................................................................................... 1 piece
User manual ......................................................................................................................................... 1 piece
The images provided in this manual are for illustrative purposes only, refer to the actual product for
confirmation.
PRODUCT DATA SHEET RELATING TO ENERGY
Brand
CONTINENTAL EDISON
Reference
CELED494K1018B7
(Model: NM49)
Energy efficiency class
A
Visible screen diagonal
123.5 cm; 49 inches
Power consumption in On mode (W)
78 W
Energy consumption (kWh per year), based on the power
consumption of a TV operating four hours a day for three hundred
and sixty-five days. The actual consumption depends on the
conditions of use of the TV.
114 kWh/year
Power consumption in Standby mode (W)
<0.5W
Power consumption in Off mode (W)
0.5W
Screen resolution (pixels)
3840 x 2160
16
III. INSTALLATION
A. Unpacking
Your TV must be unpacked and handled by 2 persons to avoid any risk of deformation or shock on the
LED screen.
Start by preparing a flat surface covered with a soft, thick cloth (for example, a blanket). The prepared
surface should be larger than the size of the TV. It will allow you to lay the TV flat, LED screen towards
the floor.
Before removing the TV from its packaging, read the "Wall mounting" and "Installing the feet"
paragraphs to prepare for the selected operation.
Remove the TV from its packaging by lifting it vertically, then lay the TV screen flat on the previously
protected flat surface so that you can attach either the feet or a wall mounting bracket (not supplied).
Packaging materials
- The packaging box is recyclable.
- Materials marked with the symbol are recyclable.
- >PE< = polyethylene; >PS< = polystyrene; >PP< = polypropylene; … This means
that they can be recycled by disposing of them in appropriate collection containers.
- Other packaging elements (adhesive, fasteners ...) must be disposed of with
household waste.
For more information: www.quefairedemesdechets.fr
B. Wall mounting
Contact a professional to get help with wall mounting your TV. We cannot be held responsible in
the event of damage or injury caused by the mounting of the TV.
The TV must be mounted on a vertical wall. This TV is not intended for mounting on a
sloping wall.
The TV must be switched off and disconnected from the mains when you mount it on the wall.
Failure to observe these precautions could result in the risk of electrification or electrocution.
The mounting bracket must correspond to the distances shown below.
NOTE: the supplied screws are used to attach the feet only. If you want to mount the TV on a wall,
contact a professional to find out how to install a wall mount.
Back view of your TV
17
C. Installing the feet
Your TV comes with unassembled feet. Before using this free standing TV on furniture, install
the feet as shown below.
Step 1
Place the TV flat, screen facing down, on a flat
surface covered with a soft, thick cloth to avoid
damaging it.
The lower edge of the TV should protrude
slightly from the edge of the flat surface to allow
the feet to be attached without damaging the
LED screen.
Step 2
Align the bottom of the TV with the feet until they
are fully in place (mounting holes aligned).
Step 3
Tighten the supplied screws using a
screwdriver.
NOTE: unplug the TV from the mains outlet when installing or removing the feet of the TV.
Contact one of our partners to learn more about how to install and remove the feet of the TV.
18
D. Basic connections
Make sure all cables are disconnected from the main unit before connecting the mains cable to
the wall outlet.
Read the instructions carefully before connecting any other device.
Connect to an outdoor antenna (ANT)
Plug an antenna into the antenna terminal to get the best possible picture quality. The use of
antenna amplifiers is optional or depends on the type of outdoor antenna used.
HDMI connection
1- Turn off your LED TV as well as the DVD player
(or any other external terminal).
2- Connect one end of the HDMI cable to your DVD
player (or any other external terminal) and the other end of
the cable to the back of your TV.
3- Turn on your TV LED as well as the DVD player
(or any other external terminal).
4- Select HDMI with the SOURCE key located on the
front of the TV or by pressing the SOURCE key on the
remote control directly.
HDMI cable
(not included)
19
Earphone/headphone connection
WARNING ABOUT LISTENING VOLUME WITH
HEADPHONES.
1. Be sure to turn down the volume before plugging in your
headset, then increase it later if necessary.
2. The sound of the TV speakers will be muted when a
headset is connected.
Coaxial connection
Use a coaxial cable to connect an audio amplifier or other audio decoding
device for coaxial audio output.
(The coaxial cable is not supplied)
Earphone cable and earphone
(not included)
20
AV connection
1. Turn off your LED TV as well as the DVD player (or any
other external terminal).
2. Connect one end of the cable to the VIDEO jack of
your DVD player (or any other external terminal) and the
other end of the cable to the VIDEO jack on the back of
your TV.
3. Connect the D (red) and L (white) audio connectors to
the AV audio jacks on the back of your DVD player (or any
other external terminal) and their end to the back of your
TV.
4. Turn on your TV as well as the DVD player (or any
other external terminal).
5. Select AV with the SOURCE key located on the front of
the TV or by pressing the SOURCE key on the remote
control directly.
NOTE: when connecting an external device, match the
colour of the terminal to that of the cable.
YPbPr and audio connection
1. Turn off the LED TV and the DVD player.
2. Use the green area connectors, connect the y (green)
connector, the Pb (blue) connector, and the Pr (red)
connector on the back of your DVD player to the
corresponding YPbPr connectors in the analog HD
component group located on the back of your TV.
3. Turn on the LED TV and the DVD player.
4. Select COMPONENT using the SOURCE key located on
the front of the TV or by pressing the SOURCE key on the
remote control directly.
NOTE: when connecting an external device, match the colour of the terminal to that of the cable
Cable
(not included)
Audio cable and YPbPr
(not included)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/