email@windonbay.com 07.03.19
|
92-W2151-01
INSTALLATION GUIDE: COMMERCIAL KITCHEN FAUCET
PRODUCT SPECS AND STANDARDS:
DESCRIPTION:
• Brass under body with flexible supplies.
• Flexible supply lines with 9/16-24
(3/8" Compression) ends.
• Single Hole Mounting: (Ø 1-1/4” Min to
Ø 1-5/8” Max)
OPERATION:
• Requires less than 5LB force to operate valve
• Flow adjustment: 90° turn from full hot to
full cold
• 1.8 GPM (6.8 L/min) Aerator
PRODUCT SPECS AND STANDARDS:
STANDARDS:
• ASME A112.18.1/CSA B125.1
• NSF/ANSI 61
• NSF/ANSI 372
• CEC (CALIFORNIA ENERGY COMMISSION)
WARRANTY:
• 25 Year drip-free warranty
• Product to be free of defects in material
or workmanship
PRODUCT WARRANTY:
Windon Bay faucets have been manufactured to our high quality standards and workmanship. The warranty covers defects in materials and/ or
workmanship to the original purchaser/home owner (warranty is not transferable to another person). The faucet is warranted to remain
drip-free during normal use. All parts and finishes will be free from manufacturing defects. With the exception of items listed below, this product has a limited
warranty against defects in materials or workmanship for a period of 1 year from the date of purchase. The warranty is voided if the product is found to be
misused or the following cleaning instructions were not followed. Damage due to accidents or installation is not warranted.
1. Faucet valve cartridges have a limited warranty for a period of 25 years from the date of purchase. This date is stamped on the valve cartridge.
2. Product finish has a limited warranty for a period of 25 years from the date of purchase. Failure to follow the cleaning instructions listed below voids all
finish warranty. Damage due to accidents or installation is not warranted.
This warranty covers replacement of cartridges, parts and finish only. It does not include labor charges and/or damage incurred during
installation. Windon Bay will provide free of charge all parts and cartridges found to be covered under the warranty; any part that proves defective in
material and/or workmanship under normal installation, use and service. Finish warranty is not covered if finish is exposed to extreme use of cleaners
containing abrasives and alcohol, extreme cleaning, extreme chemical use, or any damage due to abuse or neglect (Oil Rubbed Bronze and Matte Black
finish is warranted for 1 year).
**Please see cleaning instructions provided with each faucet. This warranty excludes all industrial, commercial, and business usage of faucets and only
pertains to single dwelling residential use. Faucets used for other than single dwelling residential use are covered by a 1-year limited warranty from the date
of purchase.
NOTE:
While your faucet may differ in appearance to
item shown, it will install with in the same manner.
CLEANING INSTRUCTIONS:
Use only a clean, soft cloth, water, and mild hand
soap to clean unit.
WARNING: Do NOT use abrasive cleaners,
chemicals, or abrasive cleaning pads to clean
fixture. A very hard protective coating has been
applied to this product to maintain it’s appearance,
but this product could be damaged with improper
cleaning. Failure to follow cleaning instructions will
void product warranty.
HELPFUL TOOLS
Adjustable
Wrench
Safety
Glasses
Phillips
Screwdriver
email@windonbay.com 07.03.19
|
92-W2151-01
INSTALLATION GUIDE: COMMERCIAL KITCHEN FAUCET
2
Accepts a 3/8”
Compression
Fitting
*SUPPLY STOPS NOT INCLUDED
1
3
TURN OFF WATER SUPPLIES.
Ensure mounting surface requirements are
as follows:
• Single Hole Mounting: (Ø 1-1/4” Min to
Ø 1-5/8” Max)
1
MOUNT UNIT ON KITCHEN SINK.
Place Hoses one at a time through mounting
hole. Lower Faucet into position. If installing
optional deckplate, place hoses through
deckplate first. Secure with Rubber Washer,
Metal Washer, and Mounting Nut. Final tighten
screws of Mounting Nut with Phillips
Screwdriver.
2
ASSEMBLE WATER SUPPLY LINES.
Inlet supplies are 3/8" Compression. Secure
to water supply and wrench tighten.
3
1
1
4
"
MIN
1
5
8
"
MAX
4
5
INSTALLATION GUIDE: COMMERCIAL KITCHEN FAUCET
email@windonbay.com 07.03.19
|
92-W2151-01
CARTRIDGE VALVE REPLACEMENT:
TURN OFF WATER SUPPLIES.
Should you need to replace the Valve Cartridge,
please follow the steps below.
• Remove Handle by removing Set Screw using
a Hex Wrench.
• Remove Valve Cartridge Cap Nut and
Retaining Ring.
• Replace Cartridge.
• Reassemble in reverse order.
6
TURN ON WATER AND FLUSH
THE SYSTEM.
Remove Spray Head from faucet. Turn on Water
Supplies and flush system for 1 minute.
Reassemble Spray Head to faucet. Activate faucet
and inspect for leaks at all connections.
4
CONFIRM PROPER INSTALLATION
Check for leaks and proper operation of faucet.
5
CARTRIDGE CAP
RETAINING RING
CARTRIDGE
SET SCREW
CARTRIDGE VALVE REPLACEMENT
6
CALIFORNIA PROPOSITION 65:
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to www. P65Warnings.ca.gov.
Wash hands after installation, repair, or removal of this product.
email@windonbay.com 07.03.19
|
92-W2151-01
ROUGH-IN DIAGRAM: COMMERCIAL KITCHEN FAUCET
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) UNLESS
OTHERWISE SPECIFIED. DIMENSIONS SUBJECT TO
CHANGE WITHOUT NOTICE.
3
3
16
"
81mm
MAX DECK THICKNESS
2
3
16
"
55mm
1-1/4" MIN DECK HOLE SIZE
5"
127mm
9/16-24 UNEF-2B
20
3
8
"
517mm
8
1
8
"
206mm
8
11
16
"
220mm
10
11
16
"
272mm
2"
51mm
MIN TO SINK LEDGE
2"
51mm
MIN TO WALL
RPG05-112703
CARTRIDGE
1
RPG05-112894-XX (XX=FINISH)
SPRAYHEAD ASSEMBLY WITH SEALS
2
1
2
REPAIR PARTS: COMMERCIAL KITCHEN FAUCET
-
1
-
2
-
3
-
4
Windon Bay W2151SS Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Safavieh BRF1057C Dimensions Guide
-
Pacific Bay PB-LU02CP User guide
-
Speakman SB-2141 Installation guide
-
-
Fontaine MFF-AVZK3-CP Installation guide
-
-
-
-
BOMANN BZ 6029 Owner's manual
-
KRAUS KPF-1690-FF-100BG User manual
