INSTRUCTIONS FOR MODELS
92-SB-1042-02
For additional assistance or service please contact:
SPEAKMAN
®
800-537-2107
customerser[email protected]
www.speakman.com
SB-1042
HELPFUL TOOLS & SUPPLIES:
TOOLS AND SUPPLIES
Phillips
Screwdriver
Adjustable
Wrench
5 Gallon
Bucket
Safety
Glasses
Warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
SAFETY TIPS
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
• This faucet has an operating range of 20-80 psi.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives may damage the finish and
void the product warranty. Please be sure to only use
approved cleaners. Please contact Speakman for any
clarification of acceptable cleaners.
1
Verify the Rubber Washer (1) is seated at the
bottom of the Faucet. If not, place the Rubber
Washer (1) over hoses and align to base of
Faucet.
NOTE: For single hole sink only.
2
Place Hoses, one at a time, thru hole in
mounting surface. Lower Faucet into position. If
installing optional deckplate, place hoses
through deckplate first.
3
Slide Easy Mount Nut (1) upwards until it makes
contact with the underside of mounting surface.
Rotate by hand to final tighten.
4
Make connections to water supplies. The inlet
threads of the faucet are 9/16”-24 UNF and
will accept a 3/8” Compression Fitting.
Wrench Tighten. Do not over-tighten.
Accepts a 3/8”
Compression
Fitting
SUPPLY STOPS NOT INCLUDED
5
If water supply is 1/2" Compression, use the
provided adapter and 1/2" IPS faucet
connections (not supplied) ❶ or use the supplied
coupling nuts ❸ with 3/8” O.D. ball nose risers
(not supplied) ❷. Use wrenches to tighten
connections. Do not over-tighten.
INLET SUPPLIES NOT INCLUDED
6
Place the spray hose (exiting from base of
faucet) into a bucket. Turn ON water supplies.
Flush both HOT and COLD water for 1 minute
into the bucket.
7
Turn OFF water supplies. Connect the spray
hose to the outlet hose. This is a push to connect
connection. Make sure to push the hose
completely into the outlet fitting.
8
• Install the Weight Clip (1) at the point of the
hose marked “Weight Here”.
• Insert the Weight (2) onto the Clip (1) by
sliding it down onto the Clip (1).
WEIGHT
HERE
WEIGHT
HERE
9
Turn ON water supplies and check for leaks.
SB-1042 REPAIR PARTS
SPEAKMAN
®
ITEM NO. PART NO. DESCRIPTION
RPG05-108762 CARTRIDGE
RPG05-112989-XX (XX=FINISH) SPRAYHEAD ASSEMBLY WITH SEAL
NOTES:
COMPLIANCE:
CONNECTIONS:
• ASME A112.18.1/CSA B125.1
• NSF/ANSI 61
• NSF/ANSI 372
• CEC (CALIFORNIA ENERGY
COMMISSION)
Supply Connection:
1/2-14 NPSM-2A Connection or
9/16"-24 UNF Connection
(3/8" Compression)
FLOW DATA:
• 1.8 gpm (6.8L/min)
2"
MIN. TO LEDGE
51mm
2"
MIN. TO WALL
51mm
KITCHEN ROUGH-IN
35mm
1
3
8
"
MIN
2
1
8
"
53mm
1-3/8" MIN DECK HOLE SIZE
2
3
4
"
71mm
MAX DECK THICKNESS
4
1
2
"
115mm
1/2" - 14 NPSM THREAD
9
1
16
"
230mm
10
3
4
"
272mm
7
3
4
"
197mm
2
"
51mm
MIN DISTANCE
TO SINK EDGE
2
"
51mm
MIN DISTANCE
TO WALL
OR
SB-1042 ROUGH-IN DIAGRAM
SPEAKMAN
®
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) UNLESS
OTHERWISE SPECIFIED. DIMENSIONS SUBJECT TO
CHANGE WITHOUT NOTICE.
-
1
-
2
Speakman SB-1042-SS Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Speakman SB-1041-BN Installation guide
-
-
-
-
-
-
-
-
-
Speakman SB-2721 Installation guide
