2. Kichler Lighting
  3. 85057CH

Kichler Lighting 85057CH, 85054CH, 85055CH, 85056CH User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 85057CH User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • Where can I find warranty information for this fixture?
    What type of cleaning products should be used on this fixture?
    Which type of dimmer switch should be used with this fixture for optimal performance?
    What should be done if the fixture causes interference with radio or television reception?
    In what position should the fixture be mounted?
    How many screws are needed to secure the canopy to the wall?
    How many knobs are needed to secure the glass to the main body?
IS-85054-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Remove the needed punch outs and aach mounng strap[A]
to outlet box[D] with the two (2) strap mounng screws[E].
Mounng strap can be adjusted to suit posion of xture.
2) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole
and two raised dimples, wrap ground wire from outlet
box around green ground screw, and thread into hole.
b) On xtures where a cupped washer is provided, aach
ground wire from outlet box under cupped washer and
green ground screw, then thread into mounng strap.
If xture is provided with ground wire, connect xture ground
wire to outlet box ground wire with wire connector aer
following the above steps. Never connect ground wire to black
or white power supply wires.
Fixture Diagram
Parts List
[A] Mounting
Strap
[B] Main Body
[C] Flat Head
Screw
[D] Outlet Box
[E] Strap
Mounting
Screws
[F] Glass
[G] Knobs
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the
Naonal Electrical Code (NEC) and all local code specicaons.
If you are not familiar with code requirements, installaon by a
cered electrician is recommended.
DIMMING:
This LED xture is compable with most standard incandescent
dimmers, LED dimmers, and electronic low voltage dimmers.
For opmal performance, an electronic low voltage dimmer should
be used.
CLEANING:
Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning
products may damage the nish.
Installaon Instrucons
This device complies with part 15 of the FCC Rules. Operaon is subject to the
following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instrucons, may cause
harmful interference to radio communicaons. However, there is no guarantee that
interference will not occur in a parcular installaon. If this equipment does cause
harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
For warranty informaon please visit: kichler.com/warranty
Installaon Instrucons (connued)
3) Make wire connecons. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
4) Push xture to wall. NOTE: Fixture to be mounted with glass in
the down posion. Make sure all wires are inside canopy and
do not get pinched between wall and canopy of xture. Use
the one (1) at head screw[C] to secure the canopy to the wall
by threading into the top of the canopy. Tighten to secure.
5) Carefully install the glass[F] by gently sliding over the three (3)
arms onto the main body[B] and secure into place with three
(3) knobs[G] as shown.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
D
A
E
C
F
G
B
Page is loading ...
IS-85054-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Remove the needed punch outs and aach mounng strap[A]
to outlet box[D] with the two (2) strap mounng screws[E].
Mounng strap can be adjusted to suit posion of xture.
2) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole
and two raised dimples, wrap ground wire from outlet
box around green ground screw, and thread into hole.
b) On xtures where a cupped washer is provided, aach
ground wire from outlet box under cupped washer and
green ground screw, then thread into mounng strap.
If xture is provided with ground wire, connect xture ground
wire to outlet box ground wire with wire connector aer
following the above steps. Never connect ground wire to black
or white power supply wires.
Fixture Diagram
Parts List
[A] Mounting
Strap
[B] Main Body
[C] Flat Head
Screw
[D] Outlet Box
[E] Strap
Mounting
Screws
[F] Glass
[G] Knobs
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the
Naonal Electrical Code (NEC) and all local code specicaons.
If you are not familiar with code requirements, installaon by a
cered electrician is recommended.
DIMMING:
This LED xture is compable with most standard incandescent
dimmers, LED dimmers, and electronic low voltage dimmers.
For opmal performance, an electronic low voltage dimmer should
be used.
CLEANING:
Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning
products may damage the nish.
Installaon Instrucons
This device complies with part 15 of the FCC Rules. Operaon is subject to the
following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instrucons, may cause
harmful interference to radio communicaons. However, there is no guarantee that
interference will not occur in a parcular installaon. If this equipment does cause
harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
For warranty informaon please visit: kichler.com/warranty
Installaon Instrucons (connued)
3) Make wire connecons. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
4) Push xture to wall. NOTE: Fixture to be mounted with glass in
the down posion. Make sure all wires are inside canopy and
do not get pinched between wall and canopy of xture. Use
the one (1) at head screw[C] to secure the canopy to the wall
by threading into the top of the canopy. Tighten to secure.
5) Carefully install the glass[F] by gently sliding over the three (3)
arms onto the main body[B] and secure into place with three
(3) knobs[G] as shown.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
D
A
E
C
F
G
B
Page is loading ...
/