Kichler Lighting 85054CH is a dimmable LED fixture compatible with most standard incandescent dimmers, LED dimmers, and electronic low voltage dimmers. It features a mounting strap that can be adjusted to suit the position of the fixture, making it suitable for various installation scenarios. The fixture comes with a glass shade that needs to be gently slid over the three arms onto the main body and secured with knobs. For optimal performance, an electronic low voltage dimmer is recommended.
Kichler Lighting 85054CH is a dimmable LED fixture compatible with most standard incandescent dimmers, LED dimmers, and electronic low voltage dimmers. It features a mounting strap that can be adjusted to suit the position of the fixture, making it suitable for various installation scenarios. The fixture comes with a glass shade that needs to be gently slid over the three arms onto the main body and secured with knobs. For optimal performance, an electronic low voltage dimmer is recommended.
IS-85054-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Remove the needed punch outs and aach mounng strap[A]
to outlet box[D] with the two (2) strap mounng screws[E].
Mounng strap can be adjusted to suit posion of xture.
2) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole
and two raised dimples, wrap ground wire from outlet
box around green ground screw, and thread into hole.
b) On xtures where a cupped washer is provided, aach
ground wire from outlet box under cupped washer and
green ground screw, then thread into mounng strap.
If xture is provided with ground wire, connect xture ground
wire to outlet box ground wire with wire connector aer
following the above steps. Never connect ground wire to black
or white power supply wires.
Fixture Diagram
Parts List
[A] Mounting
Strap
[B] Main Body
[C] Flat Head
Screw
[D] Outlet Box
[E] Strap
Mounting
Screws
[F] Glass
[G] Knobs
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the
Naonal Electrical Code (NEC) and all local code specicaons.
If you are not familiar with code requirements, installaon by a
cered electrician is recommended.
DIMMING:
This LED xture is compable with most standard incandescent
dimmers, LED dimmers, and electronic low voltage dimmers.
For opmal performance, an electronic low voltage dimmer should
be used.
CLEANING:
Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning
products may damage the nish.
Installaon Instrucons
This device complies with part 15 of the FCC Rules. Operaon is subject to the
following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instrucons, may cause
harmful interference to radio communicaons. However, there is no guarantee that
interference will not occur in a parcular installaon. If this equipment does cause
harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
For warranty informaon please visit: kichler.com/warranty
Installaon Instrucons (connued)
3) Make wire connecons. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
4) Push xture to wall. NOTE: Fixture to be mounted with glass in
the down posion. Make sure all wires are inside canopy and
do not get pinched between wall and canopy of xture. Use
the one (1) at head screw[C] to secure the canopy to the wall
by threading into the top of the canopy. Tighten to secure.
5) Carefully install the glass[F] by gently sliding over the three (3)
arms onto the main body[B] and secure into place with three
(3) knobs[G] as shown.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
D
A
E
C
F
G
B
Page is loading ...
IS-85054-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Remove the needed punch outs and aach mounng strap[A]
to outlet box[D] with the two (2) strap mounng screws[E].
Mounng strap can be adjusted to suit posion of xture.
2) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole
and two raised dimples, wrap ground wire from outlet
box around green ground screw, and thread into hole.
b) On xtures where a cupped washer is provided, aach
ground wire from outlet box under cupped washer and
green ground screw, then thread into mounng strap.
If xture is provided with ground wire, connect xture ground
wire to outlet box ground wire with wire connector aer
following the above steps. Never connect ground wire to black
or white power supply wires.
Fixture Diagram
Parts List
[A] Mounting
Strap
[B] Main Body
[C] Flat Head
Screw
[D] Outlet Box
[E] Strap
Mounting
Screws
[F] Glass
[G] Knobs
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the
Naonal Electrical Code (NEC) and all local code specicaons.
If you are not familiar with code requirements, installaon by a
cered electrician is recommended.
DIMMING:
This LED xture is compable with most standard incandescent
dimmers, LED dimmers, and electronic low voltage dimmers.
For opmal performance, an electronic low voltage dimmer should
be used.
CLEANING:
Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning
products may damage the nish.
Installaon Instrucons
This device complies with part 15 of the FCC Rules. Operaon is subject to the
following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instrucons, may cause
harmful interference to radio communicaons. However, there is no guarantee that
interference will not occur in a parcular installaon. If this equipment does cause
harmful interference to radio or television recepon, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
For warranty informaon please visit: kichler.com/warranty
Installaon Instrucons (connued)
3) Make wire connecons. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
4) Push xture to wall. NOTE: Fixture to be mounted with glass in
the down posion. Make sure all wires are inside canopy and
do not get pinched between wall and canopy of xture. Use
the one (1) at head screw[C] to secure the canopy to the wall
by threading into the top of the canopy. Tighten to secure.
5) Carefully install the glass[F] by gently sliding over the three (3)
arms onto the main body[B] and secure into place with three
(3) knobs[G] as shown.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
D
A
E
C
F
G
B
Page is loading ...
-
1
-
2
-
3
-
4
Kichler Lighting 85054CH User manual
- Type
- User manual
Kichler Lighting 85054CH is a dimmable LED fixture compatible with most standard incandescent dimmers, LED dimmers, and electronic low voltage dimmers. It features a mounting strap that can be adjusted to suit the position of the fixture, making it suitable for various installation scenarios. The fixture comes with a glass shade that needs to be gently slid over the three arms onto the main body and secured with knobs. For optimal performance, an electronic low voltage dimmer is recommended.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 85068PN User manual
-
Kichler Lighting 85068PN User manual
-
Kichler Lighting 11315NILED User manual
-
Kichler Lighting 11319NILED User manual
-
Kichler Lighting 85064CH User manual
-
Kichler Lighting 85081CH User manual
-
Kichler Lighting 85078CH User manual
-
Kichler Lighting 11315OZLED User manual
-
Kichler Lighting 85081CH User manual
-
Kichler Lighting 85049CH User manual
