EnviroLite EVTR24DI42WD Installation guide

Brand: EnviroLite

Model: EVTR24DI42WD

Type: Installation guide

EnviroLite EVTR24DI42WD is a LED direct/indirect troffer light with 42 Watts of power, suitable for damp locations and operating in temperatures ranging from -20°C to 45°C. It can be dimmed using a 0-10V dimmer, and it has a power factor of >0.9. The light is suitable for use in both residential and commercial applications, and it is easy to install and maintain. With its sleek design and energy-efficient LED technology, the EnviroLite EVTR24DI42WD is a great choice for any lighting project.

INSTRUCTION MANUAL

LED DIRECT/INDIRECT TROFFER LIGHT

This product has been manufactured with the highest standards of safety and quality.

CHARACTERISTICS:

Electrical System Input Power: 42 W

Input Voltage: 120-277 VAC

Input Frequency: 50/60 Hz

Power Factor: > 0.9

Dimmable: 0 – 10 V

Temperature Operating Temperature: -20°C to 45°C

TOOLS REQUIRED:

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

(1) Luminaire

Phillips

Screwdriver

Wire

Cutter

Wire

Stripper

Pliers

Ladder

Safety

Goggles

Electrical

Tape

2 Wire

Nuts

CAUTION:

1. Before starting installation of this fixture or removal of a previous fixture, disconnect

the power by turning off the circuit breaker or by removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL

QUESTIONS. If you have any non-electrical questions about this fixture, please call

our Customer Service Team at phone# on carton label.

3. KEEP your receipt and these Instructions for Proof of Purchase.

GENERAL:

1. All electrical connections must be in accordance with local, and national electrical

codes.

2. Prior to installation it is important to follow the following guidelines:

A. Turn off the main power at the circuit breaker before installing the fixture, to

prevent possible shock.

B. Be sure that all wires were not damaged during installation and that there are no

rough or sharp edges in contact with the wires.

WARNING:

 Min 75°C supply conductors, Type IC, INHERENTLY PROTECTED.

 This product must be installed in accordance with the applicable installation code by a

person familiar with the construction and operation of the product and the hazards

involved.

 Blinking light of this thermally protected luminaire may indicate overheating.

 Vapor barrier must be suitable for 75°C.

 Suitable for damp locations.

INSTALLATION AND ASSEMBLY:

1. Turn off the power at the circuit breaker box.

2. Remove the fixture from the packaging.

3. Rest the luminaire on the T-Bar of the ceiling

suspension system in the desired location.

(Fig. 1)

4. From above the ceiling, secure the Troffer to

T-Bar by bending built in T-bar clips (#1) on

all four corners of the fixture. (Fig. 2)

5. If local code requires, tie a wire to at least

two of the four T-bar clips (#1) located near

each corner of the Troffer to a structural

member of the ceiling. (Fig. 2)

6. Remove the access plate (#2) and locate the

black fixture wire and the white fixture wire.

(Fig. 3)

7. Remove the access plate located on end of

fixture (#3) and locate the purple fixture wire

and the grey fixture wire. (Fig. 3)

8. Thread the power supply wires through the

knockout hole in the access plate (#2). (Fig.

9. Connect the black supply wire and the white

supply wire to the quick connector. Connect

the supply ground wire to the fixture ground

screw.

10. If the fixture will not be connected to a

dimmer, cap off the purple and grey fixture

wires individually with a wire nut. (Fig. 4)

11. If the fixture will be connected to a dimmer,

thread the dimming wires through the

knockout hole in the access plate (#3) (Fig.

3) and connect the purple and grey fixture

wires to corresponding wires of the wall 0-

10V dimmer. (Fig. 5)

12. Restore power at the circuit breaker box.

Fig. 2

Fig. 4

PURPLE FIXTURE WIRE

GREY FIXTURE WIRE

NO DIMMING

Fig. 5

PURPLE FIXTURE WIRE PURPLE DIMMER WIRE

DIMMING CONNECTIONS

GREY FIXTURE WIRE GREY DIMMER WIRE

Fig. 3

Fig. 1

DIMMING:

Brand

Series

Model #

Wiring

Load

Capacity (A)

Dimming

Range

Max # of

Luminaires

@ 120V

Max # of

Luminaires

@ 277V

Leviton

Illumatech

IP710-LFZ

3-Way

5% - 100%

Lutron

Diva

DVSTV

3-Way

5% - 100%

Maestro

MS-Z101

3-Way

9% - 100%

Nova T

NTSTV

single

7% - 100%

Philips

Sunrise

Preset

SR500ZTUNV

3-Way

5% - 100%

Luxdrive

A019

4% - 100%

OPERATION:

 Turn on power at the circuit breaker or fuse box.

 Turn the light switch on to activate the fixture.

CARE AND CLEANING:

NOTE: Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a

dry soft cloth to dust or wipe carefully.

 Use a dry or slightly dampened clean cloth and wipe the surface of the fixture.

 Disconnect power to the fixture by turning off the circuit breaker or by removing the

fuse at the fuse box.

 Use a dry or slightly dampened clean cloth to wipe the interior surface of the fixture.

TROUBLESHOOTING:

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiver antenna.

 Increase the separation between the equipment and receiver.

 Install the product onto on a circuit different from that to which the receiver is

connected.

 Consult with the dealer or an experienced radio/TV technician for help.

 CAUTION: Any changes made to the electronics circuit will void this equipment’s

compliance with Part 15 of the FCC Rules and should not be operated.

Problem

Solution

The light will not turn on.

 Make sure the power supply is on.

 Test or replace the switch.

 Check the wiring.

 Make sure the grey and purple dimming wires

are not touching each other.

The fuse blows or circuit breaker

trips when light is turned on.

 Check the wire connections.

Page is loading ...

EnviroLite EVTR24DI42WD Installation guide

Brand: EnviroLite

Model: EVTR24DI42WD

Type: Installation guide

Download PDF

report

in other languages

français: EnviroLite EVTR24DI42WD Guide d'installation
español: EnviroLite EVTR24DI42WD Guía de instalación

EnviroLite EVTR24DI42WD Installation guide

EnviroLite EVTR24DI42WD Installation guide

in other languages

Related papers

Other documents